Search

In this study, a novel COF TABT @COF TATp modified magnetic MXene composite (CoFe 2 O 4 @Ti 3 C 2 @COF TABT @COF TATp ) was synthesized by Schiff base reaction and irre-versible enol-keto tautomerization, and employed to establish a sensitive monitoring method for six thiophene compounds in oilfield produced water samples based on magnetic solid-phase extraction (MSPE) prior to gas chromatography coupled with a triple quadruple mass spectrometer (GC-MS/MS). The designed magnetic materials exhibited unexpected enrichment ability to target thiophene compounds and achieved good extraction efficiencies ranging from 83 % to 98 %. The developed MSPE/GC-MS/MS method exhibited good linearity in the range of 0.001-100 μg L -1 , and obtained lower limits of detection ranging from 0.39 to 1.9 ng L -1 . The spiked recoveries of thiophene compounds obtained in three oilfield produced water samples were over the range of 96.26 %-99.54 % with relative standard deviations (RSDs) less than 3.7 %. Notably, benzothiophene, 4-methyldibenzothiophene and 4,6-dimethyldibenzothiophene were detected in three oilfield-produced water samples. Furthermore, the material still kept favorable stability after six recycling experiments. The adsorption kinetics, adsorption isotherms as well as adsorption thermodynamics of thiophene compounds were investigated in detail to provide insight into the mechanisms. Overall, the present work contributed a promising strategy for designing and synthesizing new functionalized materials for the enrichment and detection of typical pollutants in the environment., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier B.V. All rights reserved.)

The oil industry is facing substantial environmental challenges, especially in managing waste streams such as Oilfield Produced Water (OPW), which represents a significant component of the industrial ecological footprint. Conventional treatment methods often fail to effectively remove dissolved oils and grease compounds, leading to operational difficulties and incomplete remediation. Electrochemical oxidation (EO) has emerged as a promising alternative due to its operational simplicity and ability to degrade pollutants directly and indirectly, which has already been applied in treating several effluents containing organic compounds. The application of EO treatment for OPW is still in an initial stage, due to the intricate nature of this matrix and scattered information about it. This study provides a technological overview of EO technology for OPW treatment, from laboratory scale to the development of large-scale prototypes, identifying design and process parameters that can potentially permit high efficiency, applicability, and commercial deployment. Research in this domain has demonstrated notable rates of removal of recalcitrant pollutants (>90%), utilizing active and non-active electrodes. Electro-generated active species, primarily from chloride, play a pivotal role in the oxidation of organic compounds. However, the highly saline conditions in OPW hinder the complete mineralization of these organics, which can be improved by using non-active anodes and lower salinity levels. The performance of electrodes greatly influences the efficiency and effectiveness of OPW treatment. Various factors must be considered when selecting the electrode material, such as its conductivity, stability, surface area, corrosion resistance, and cost. Additionally, the specific contaminants present in the OPW, and their electrochemical reactivity must be considered to ensure optimal treatment outcomes. Balancing these considerations can be challenging, but it is crucial for achieving successful OPW treatment. Active electrode materials exhibit a high affinity for chloride molecules, generating more active species than non-active materials, which exhibit more significant degradation potential due to the production of hydroxyl radicals. Regarding scale-up, key challenges include low current efficiency, the formation of by-products, electrode deactivation, and limitations in mass transfer. To address these issues, enhanced mass transfer rates and appropriate residence times can be achieved using flow-through mesh anodes and moderate current densities, which have proven to be the optimal configuration for this process., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

The issue of material failure attributed to microbiologically influenced corrosion (MIC) is escalating in seriousness. Microorganisms not only facilitate corrosion but certain beneficial microorganisms also impede its occurrence. This study explored the impact of marine B. velezensis on the corrosion behavior of X65 steel in simulated offshore oilfield produced water. B. velezensis exhibited rapid growth in the initial stages, and the organic acid metabolites were found to promote corrosion. Subsequently, there was an increase in cross-linked "networked" biofilms products, a significant rise in the prismatic shape of corrosion products, and a tendency for continuous development in the middle and late stages. The organic/inorganic mineralized film layer formed on the surface remained consistently complete. Metabolic products of amino acid corrosion inhibitors were also observed to be adsorbed into the film. B. velezensis altered the kinetics of the X65 steel cathodic reaction, resulting in a deceleration of the electrochemical reaction rate. The mineralization induced by B. velezensis effectively slowed down the corrosion rate of X65 steel., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier B.V. All rights reserved.)

Nature-based solutions are encouraged for treating oilfield produced water from oil and gas extraction, a crucial undertaking that aligns with the Canadian oil sands industry's ambitious goal of zero waste, and the globally recognized Sustainable Development Goals (SDGs) pertaining to water conservation and ecosystem preservation. This study explored the use of peat-mineral mix (PMM), a leftover of inevitable oil sands mining, for treating low and high-strength wastewaters during biofiltration, which contained large molecular weight (44.3 kDa), which include alcohols, aliphatics, aromatics, and ketones, and can impart high toxicity to both fauna and flora (MicroTox: 99 %). The breakthrough curve indicated an effective initial adsorption phase driven by advection within the column dynamics. For complete organics removal and mechanistic insights, the wastewater was re-circulated in a continuous mode for up to 42 days. Here, we found that chemical oxygen demand was reduced from ∼85,000 mg/L to ∼965 mg/L). Kinetics investigations along with physicochemical characterization of PMM and wastewater suggested that chemisorption and anaerobic digestion contributed to the overall removal of contaminants. Chemisorption, led by hydrogen bonding and hydrophobic interactions, was the dominant mechanism, with a limited contribution from physical adsorption (surface area: 2.85 m2/g). The microbial community within the PMM bed was rich/diverse (Shannon > 6.0; Chao1 > 600), with ∼ 50 % unclassified phylotypes representing 'microbial dark matter'. High electric conductivity (332.1 μS cm -1 ) of PMM and the presence of Geobacter, syntrophs, and Methanosaeta suggest that direct interspecies electron transfer was likely occurring during anaerobic digestion. Both low and high-strength wastewaters showed effective removal of dissolved organics (e.g., naphthenic acids, acid extractable fraction, oil and grease content), nutrients, and potentially toxic metals. The successful use of PMM in treating oilfield produced water offers promising avenues for embracing nature-based remediation solutions at oil refining sites., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

Fluorescence spectroscopy is a powerful tool to determine polycyclic aromatic hydrocarbons (PAHs) owing to the strong endogenous fluorescence of these compounds. However, the presence of unknown interferences and overlapped spectra hinders the accurate determination of PAHs in oilfield produced water. Moreover, surfactants frequently coexist in oilfield produced water and will seriously affect the fluorescence signals of PAHs. Herein, a new methodology applying third-order calibration to process four-way (4D) fluorescence data was proposed to solve these problems and achieve accurate determination of pyrene, fluorene, phenanthrene, and fluoranthene as an example in oilfield produced water. The methodology is based on excitation-emission matrix fluorescence modulated by different concentrations of sodium dodecyl benzene sulfonate (SDBS) in the analyzed samples. The 4D fluorescence data were processed by third-order calibration methods including four-way parallel factor analysis (4-PARAFAC) and alternating weighted residue constraint quadrilinear decomposition (AWRCQLD), and the results were compared with those of second-order calibration methods. It was proved that third-order calibration was capable of accurately identifying and quantifying PAHs together with SDBS in oilfield produced water, which has better quantitative results and figures of merit compared to second-order calibration. This study provided a new approach to generating 4D fluorescence data and opened up an avenue for the accurate determination of PAHs in complex oilfield produced water with surfactants., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier B.V. All rights reserved.)

In this study, a flat sheet ceramic membrane experimental device was constructed, and the thermodynamics of membrane fouling interface was studied for oilfield produced water. The flux of ceramic membrane in three kinds of model solutions were measured with time, as well as the surface tension, contact Angle and Zeta potential of solid. The thermodynamic mechanism of membrane fouling interface combined with XDLVO theory were explored for three kinds of model solutions. The thermodynamic study of the interface of ceramic plate membrane shows that the total interaction energy between membrane and oil droplets decreases with the increase of the distance between two interfaces at initial stage of membrane fouling, and finally transforms from the mutual attraction to the mutual repulsion. The total interaction energy between reservoir and oil droplet is shown as mutual attraction, and the total interaction energy decreases with the increase of the distance between reservoir and oil droplet interface. The zeta potential of crude oil was affected by salinity to some extent. The electrostatic shielding effect of the salt ions leads to a decrease in the ζ-potential of the three solutions. They are in the order: model solution A > model solution B > model solution C. This leads to a decrease in the electrostatic interaction (EL). And since the oil layer has the same composition as the oil droplets, the EL interactions in the three solutions can behave as mutual repulsion.

The corrosion behavior of Q235B carbon steel is investigated in water, LB medium, and oilfield produced water adding Pseudomonas fluorescens FSYZ01. After immersion at 30 °C for 13 days, the weight loss of carbon steel with this strain decreased by 32.23%, 54.07%, and 78.34%, respectively. X-ray diffraction (XRD) results show that P. fluorescens FSYZ01 inhibited conversion of iron oxides by hindering oxygen from approaching metal surface. Fourier transform infrared (FT-IR) and X-ray photoelectron spectrometer (XPS) results show that specific functional groups and bonds reacted with Fe(II/III) to form a dense and stable chelate-oxide protective layer, thereby inhibiting corrosion. Pyrolysis gas chromatography-mass spectrometer (Py-GCMS) results demonstrate the bacteria degraded C 12 to C 20 alkanes in oil. The inhibitory mechanism of crude oil-degrading bacteria P. fluorescens FSYZ01 on the carbon steel corrosion was proposed, so as to slow corrosion of oilfield produced water system pipeline and prolong its service life, helping to comprehend the microbial corrosion in the actual environment., (© 2023. The Author(s), under exclusive licence to Springer-Verlag GmbH Germany, part of Springer Nature.)

High boron (B) levels in oil and gas produced waters prevent its beneficial reuse as irrigation water without proper treatment. Aluminum (Al) electrocoagulation (EC) is a promising technology for B removal, but further research and development is needed to optimize EC for use in removing B from produced waters. To this end, B removal by adsorption onto insoluble aluminum hydroxide solids, generated by EC in simulated brines (up to 50,000 mg/L NaCl) and real oilfield produced waters, was studied. B removal during EC was greater than when aluminum hydroxide solids formed by EC were subsequently exposed to B containing solutions. Working parameters affecting B removal during the EC process, including current, total dissolved solid (TDS), temperature, pH, scale-forming cations and organic matter, were investigated to explore ways to achieve higher B removal. Boron removal increased with increased current loading and time, and with the concomitant increased Al solids concentration. However, too high a current loading limited B removal because of a change in the structure of the aluminum hydroxide solids. Higher TDS decreased B removal slightly, but lower TDS concentrations limited the use of higher current loadings. Temperature increased during EC treatment, particularly at higher current loadings, and this inhibited B removal due to an accelerated aggregation of amorphous Al solids into larger, denser, and presumably more crystalline particles. The best B removal occurred at pH 8, corresponding to a slightly positive zeta potential for aluminum hydroxide and a small but significant fraction of negatively charged B species. Scale-forming cations such as Ba 2+ and Sr 2+ had no obvious effect on the EC process. The presence of high concentrations of Mg 2+ and Ca 2+ resulted in low bulk pH values during the EC process and greater formation of solid products, but B removal did not decrease during a pH-controlled (pH = 8) EC process with these divalent cations present. Two produced water samples collected from oilfields in Kansas, US were treated using EC for 1 h, resulting in up to ~70 % B removal from solution with a current loading of 6.67 A/L, and up to 78 % with 13.33 A/L., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2022 Elsevier B.V. All rights reserved.)

Produced water is the wastewater formed when water is brought from subsurface reservoirs during oil or gas extraction. Currently, produced water is mainly treated using conventional trains that contain adsorbates, membrane filters, phase separators and cyclones. This paper reviewed the detailed characteristics of oilfield-produced water and the assessment of multiple technologies at primary, secondary, and tertiary treatments stages. The effectiveness of the treatment technology from the production of waste, energy requirements, usage of chemicals and the treatment effect of contaminants has been discussed. Then a qualitative assessment was presented in terms of energy requirements, robustness, flexibility, waste generation, modularity, and mobility, which has become critical to the development and application prospects of any technology., (Copyright © 2022 Elsevier Ltd. All rights reserved.)

Oilfield produced water (OPW) is one of the most important by-products, resulting from oil and gas exploration. The water contains a complex mixture of organic and inorganic compounds such as grease, dissolved salt, heavy metals as well as dissolved and dispersed oils, which can be toxic to the environment and public health. This article critically reviews the complex properties of OPW and various technologies for its treatment. They include the physico-chemical treatment process, biological treatment process, and physical treatment process. Their technological strengths and bottlenecks as well as strategies to mitigate their bottlenecks are elaborated. A particular focus is placed on membrane technologies. Finally, further research direction, challenges, and perspectives of treatment technologies for OPW are discussed. It is conclusively evident from 262 published studies (1965-2021) that no single treatment method is highly effective for OPW treatment as a stand-alone process however, conventional membrane-based technologies are frequently used for the treatment of OPW with the ultrafiltration (UF) process being the most used for oil rejection form OPW and oily waste water. After membrane treatment, treated effluents of the OPW could be reused for irrigation, habitant and wildlife watering, microalgae production, and livestock watering. Overall, this implies that target pollutants in the OPW samples could be removed efficiently for subsequent use, despite its complex properties. In general, it is however important to note that feed quality, desired quality of effluent, cost-effectiveness, simplicity of process are key determinants in choosing the most suitable treatment process for OPW treatment., (Copyright © 2022 Elsevier Ltd. All rights reserved.)

Freshwater scarcity is a highly pressing and accelerating issue facing our planet. Therefore, there is a great incentive to develop sustainable solutions by reusing wastewater or produced water (PW), especially in places where it is generated abundantly. PW represents the water produced as a by-product during oil and gas extraction operations in the petroleum industry. It is the largest wastewater stream within the industry, with hundreds of millions of produced water barrels per day worldwide. This research investigates a reuse opportunity for PW to replace freshwater utilization in well stimulation applications. Introducing an environmentally friendly chelating agent (GLDA) allowed formulating a PW-based fluid system that has similar rheological properties in fresh water. This work aims at evaluating the rheological properties of the developed stimulation fluid. The thickening profile of the fluid was controlled by chelation chemistry and varying different design parameters. The experiments were carried out using a high-pressure, high-temperature (HPHT) viscometer. Variables such as polymer concentration and pH have a great impact on the viscosity, while temperature and concentration of the chelating agents are shown to control the thickening profile, as well as its stability and breakage behaviors. Furthermore, 50 pptg of carboxymethyl hydroxypropyl guar (CMHPG) polymer in 20 wt.% chelating solution was shown to sustain 172 cP viscosity for nearly 2.5 h at 150 °F and 100 S -1 shear rate. The newly developed fluid system, solely based on polymer, chelating agent, and PW, showed great rheological capabilities to replace the conventional stimulation fluids based on fresh water. The newly developed fluid can also have economic value realization due to fewer additives, compared with conventional fluids.

The multistage bio-contact oxidation reactor (BCOR) is a widely used biological strategy to treat wastewater, however, little is known about the performance and microbial community information of BCOR during the treatment of low-COD and high-salinity oilfield produced water. In this study, the performance of a multistage BCOR in treating produced water was investigated. The result suggested the BCOR could efficiently remove COD, BOD 5 , NH 4 + -N, and oil pollutants. Besides, high-throughput sequencing analysis revealed that oil content was the main variable in shaping the community structure. The highest total relative abundance of potential pollutants degraders in first BCOR stage suggested significant role of this stage in pollutants removal. In addition, the correlation analysis disclosed the key functional genera during the degradation process, including Rhodobacter, Citreibacter, and Roseovarius. Moreover, network analysis revealed that the microbial taxa within same module had strong ecological linkages and specific functions., (Copyright © 2021 Elsevier Ltd. All rights reserved.)

Reuse of oilfield-produced water (OPW) for crop irrigation has the potential to make a critical difference in the water budgets of highly productive but drought-stressed agricultural watersheds. This is the first peer-reviewed study to evaluate how trace metals in OPW used to irrigate California crops may affect human health. We modeled and quantified risks associated with consuming foods irrigated with OPW using available concentration data. The probabilistic risk assessment simulated OPW metal concentrations, crop uptake, human exposures, and potential noncancer and carcinogenic health effects. Overall, our findings indicate that there is a low risk of ingesting toxic amounts of metals from the consumption of tree nuts, citrus, grapes, and root vegetables irrigated with low-saline OPW. Results show increased arsenic cancer risk (at 10 -6 ) for adult vegetarians, assuming higher consumption of multiple foods irrigated with OPW that contain high arsenic concentrations. All other cancer risks are below levels of concern and all noncancer hazards are far below levels of concern. Arsenic risk concerns could be mitigated by practices such as blending high-arsenic OPW. Future risk assessment research should model the risks of organic compounds in OPW, as our study focused on inorganic compounds. Nevertheless, our findings indicate that low-saline OPW may provide a safe and sustainable alternative irrigation water source if water quality is adequately monitored and blended as needed prior to irrigation., (© 2020 The Authors. Risk Analysis published by Wiley Periodicals LLC on behalf of Society for Risk Analysis.)

Determining a representative microbial signature from any given location is dependent on robust sample collection and handling. Different sampling locations and hence sample properties can vary widely; for example, soil would be collected and handled differently compared to liquid samples. In the event that sample material has a low concentration of biomass, large quantities need to be collected for microbial community analysis. This is certainly the case when investigating the microbiology of oilfield systems, wherein produced water (PW) is one of the most common sources for microbial sampling. As the detrimental effects of microbial metabolism within these industrial milieus are becoming increasingly well-established, the characterization of microbial community composition using molecular biological analyses is becoming more commonplace for accurate monitoring. As this field continues to develop, the importance for standardized operating protocols cannot be understated, so that industry can make the most informed operational decisions possible. Accurately identifying oilfield microbial communities is paramount, as improper preservation and storage following sample collection is known to lead to erroneous microbial identifications. Preserving oilfield PW can be challenging, as many locations are remote, requiring lengthy periods of time before samples can be processed and analyzed. While previous studies have characterized the effects of various preservatives on concentrated, filtered, or purified microbial samples, to the best of our knowledge, no such study has been undertaken on low biomass liquid samples. To this end, we investigated the effectiveness of nine different preservation conditions on PW collected from the same sampling location within a heavy-oil producing field, and monitored how the microbial community changed over the period of a month. Our results reveal that the choice of preservative drastically affects microbial community, and should be selected with careful consideration before sampling occurs., (Copyright © 2020 Rachel and Gieg.)

The consecutive occurrence of drought and reduction in natural water availability over the past several decades requires searching for alternative water sources for the agriculture sector in California. One alternative source to supplement natural waters is oilfield produced water (OPW) generated from oilfields adjacent to agricultural areas. For over 25 years, OPW has been blended with surface water and used for irrigation in the Cawelo Water District of Kern County, as permitted by California Water Board policy. This study aims to evaluate the potential environmental impact, soil quality, and crop health risks of this policy. We examined a large spectrum of salts, metals, radionuclides ( 226 Ra and 228 Ra), and dissolved organic carbon (DOC) in OPW, blended OPW used for irrigation, groundwater, and soils irrigated by the three different water sources. We found that all studied water quality parameters in the blended OPW were below current California irrigation quality guidelines. Yet, soils irrigated by blended OPW showed higher salts and boron relative to soils irrigated by groundwater, implying long-term salts and boron accumulation. We did not, however, find systematic differences in 226 Ra and 228 Ra activities and DOC in soils irrigated by blended or unblended OPW relative to groundwater-irrigated soils. Based on a comparison of measured parameters, we conclude that the blended low-saline OPW used in the Cawelo Water District of California is of comparable quality to the local groundwater in the region. Nonetheless, the salt and boron soil accumulation can pose long-term risks to soil sodification, groundwater salinization, and plant health; as such, the use of low-saline OPW for irrigation use in California will require continual blending with fresh water and planting of boron-tolerant crops to avoid boron toxicity., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2020 Elsevier B.V. All rights reserved.)

The chemistry of bacterial biofilms as well as the nutritional composition of culture environments may differ at any time within a growth process, especially for SRB consortia within oil wells with limited carbon sources. In the oilfield, the presence of SRB biofilms on surfaces of steel substrates leads to microbiologically influenced corrosion and compromised material integrity. In this work, the survival of SRB cells and their impact on the pipeline steel corrosion within simulated CO 2 -saturated oilfield-produced water with different concentrations of organic carbon source have been investigated. Cell counts reduced with the level of carbon source reduction (CSR) after incubation but more sessile cells survived at 80% CSR (moderate carbon starvation) compared to 100% CSR (extreme carbon starvation). The energy needed for cellular survival as well as biological support toward MIC could have been harnessed by a combination of extracellular Fe o oxidation and intracellular sulfate reduction even after carbon source starvation. Severe anodic steel dissolution was observed at the end of the culture period within the simulated CO 2 -saturated oilfield-produced water, and this is attributed to SRB-led MIC and CO 2 corrosion. Pipeline steel corroded more when cultured within 80% CSR compared to the medium with both lactate and citrate. Steel substrate corroded less with 100% CSR due to severely weakened SRB biofilms from nutrient deprivation., (Copyright © 2019 Elsevier B.V. All rights reserved.)

Separation and purification of oilfield produced water (OPW) is a major environmental challenge due to the co-production of the OPW during petroleum exploration and production operations. Effective capture of oil contaminant and its in-situ photodegradation is one of the promising methods to purify the OPW. Based on the photocatalytic capability of graphitic carbon nitride (GCN) which was recently rediscovered, photodegradation capability of GCN for OPW was investigated in this study. GCN was synthesized by calcination of urea and further exfoliated into nanosheets. The GCNs were incorporated into polyacrylonitrile nanofibers using electrospinning, which gave a liquid-permeable self-supporting photocatalytic nanofiber mat that can be handled by hand. The photocatalytic nanofiber demonstrated 85.4% degradation of OPW under visible light irradiation, and improved the degradation to 96.6% under UV light. Effective photodegradation of the photocatalytic nanofiber for OPW originates from synergetic effects of oil adsorption by PAN nanofibers and oil photodegradation by GCNs. This study provides an insight for industrial application on purification of OPW through photocatalytic degradation under solar irradiation., (Copyright © 2018 Elsevier Ltd. All rights reserved.)