Search

Low salinity waterflooding has proven to accelerate oil production at core and field scales. Wettability alteration from a more oil-wetting to a more water-wetting condition has been established as one of the most notable effects of low salinity waterflooding. To induce the wettability alteration, low salinity water should be transported to come in contact with the oil-water interfaces. Transport under two-phase flow conditions can be highly influenced by fluids topology that creates connected pathways as well as dead-end regions. It is known that under two-phase flow conditions, the pore space filled by a fluid can be split into flowing (connected pathways) and stagnant (deadend) regions due to fluids topology. Transport in flowing regions is advection controlled and transport in stagnant regions is predominantly diffusion controlled. To understand the full picture of wettability alteration of a rock by injection of low salinity water, it is important to know i) how the injected low salinity water displaces and mixes with the high salinity water, ii) how continuous wettability alteration impacts the redistribution of two immiscible fluids and (ii) role of hydrodynamic transport and mixing between the low salinity water and the formation brine (high salinity water) in wettability alteration. To address these two issues, computational fluid dynamic simulations of coupled dynamic two-phase flow, hydrodynamic transport and wettability alteration in a 2D domain were carried out using the volume of fluid method. The numerical simulations show that when low salinity water was injected, the formation brine (high salinity water) was swept out from the flowing regions by advection. However, the formation brine residing in stagnant regions was diffused very slowly to the low salinity water. The presence of formation brine in stagnant regions created heterogeneous wettability conditions at the pore scale, which led to remarkable two-phase flow dynamics and internal redistribution of oil, which is referred to as the "pull-push" behaviour and has not been addressed before in the literature. Our simulation results imply that the presence of stagnant regions in the tertiary oil recovery impedes the potential of wettability alteration for additional oil recovery. Hence, it would be favorable to inject low salinity water from the beginning of waterflooding to avoid stagnant saturation. We also observed that oil ganglia size was reduced under tertiary mode of low salinity waterflooding compared to the high salinity waterflooding.

There are abundant examples of natural, engineering and industrial applications, in which "solute transport" and "mixing" in porous media occur under multiphase flow conditions. Current state-of-the-art understanding and modelling of such processes are established based on flawed and non-representative models. Moreover, there is no direct experimental result to show the true hydrodynamics of transport and mixing under multiphase flow conditions while the saturation topology is being kept constant for a number of flow rates. With the use of a custom-made microscope, and under well-controlled flow boundary conditions, we visualized directly the transport of a tracer in a Reservoir-on-Chip (RoC) micromodel filled with two immiscible fluids. This study provides novel insights into the saturation-dependency of transport and mixing in porous media. To our knowledge, this is the first reported pore-scale experiment in which the saturation topology, relative permeability, and tortuosity were kept constant and transport was studied under different dynamic conditions in a wide range of saturation. The critical role of two-phase hydrodynamic properties on non-Fickian transport and saturation-dependency of dispersion are discussed, which highlight the major flaws in parametrization of existing models.

Multiphase flow in porous media is important in a number of environmental and industrial applications such as soil remediation, CO 2 sequestration, and enhanced oil recovery. Wetting properties control flow of immiscible fluids in porous media and fluids distribution in the pore space. In contrast to the strong and weak wet conditions, pore-scale physics of immiscible displacement under intermediate-wet conditions is less understood. This study reports the results of a series of two-dimensional high-resolution direct numerical simulations with the aim of understanding the pore-scale dynamics of two-phase immiscible fluid flow under intermediate-wet conditions. Our results show that for intermediate-wet porous media, pore geometry has a strong influence on interface dynamics, leading to co-existence of concave and convex interfaces. Intermediate wettability leads to various interfacial movements which are not identified under imbibition or drainage conditions. These pore-scale events significantly influence macro-scale flow behaviour causing the counter-intuitive decline in recovery of the defending fluid from weak imbibition to intermediate-wet conditions.

Entry capillary pressure is one of the most important factors controlling drainage and remobilization of the capillary-trapped phases as it is the limiting factor against the two-phase displacement. It is known that the entry capillary pressure is rate dependent such that the inertia forces would enhance entry of the non-wetting phase into the pores. More importantly the entry capillary pressure is wettability dependent. However, while the movement of a meniscus into a strongly water-wet pore is well-defined, the invasion of a meniscus into a weak or intermediate water-wet pore especially in the case of angular pores is ambiguous. In this study using OpenFOAM software, high-resolution direct two-phase flow simulations of movement of a meniscus in a single capillary channel are performed. Interface dynamics in angular pores under drainage conditions have been simulated under constant flow rate boundary condition at different wettability conditions. Our results shows that the relation between the half corner angle of pores and contact angle controls the temporal evolution of capillary pressure during the invasion of a pore. By deviating from pure water-wet conditions, a dip in the temporal evolution of capillary pressure can be observed which will be pronounced in irregular angular cross sections. That enhances the pore invasion with a smaller differential pressure. The interplay between the contact angle and pore geometry can have significant implications for enhanced remobilization of ganglia in intermediate contact angles in real porous media morphologies, where pores are very heterogeneous with small shape factors., (Copyright © 2016 The Authors. Published by Elsevier Inc. All rights reserved.)

Using a visualization setup, we characterized the solute transport in a micromodel filled with two fluid phases using direct, real-time imaging. By processing the time series of images of solute transport (dispersion) in a two fluid-phase filled micromodel, we directly delineated the change of transport hydrodynamics as a result of fluid-phase occupancy. We found that, in the water saturation range of 0.6-0.8, the macroscopic dispersion coefficient reaches its maximum value and the coefficient was 1 order of magnitude larger than that in single fluid-phase flow in the same micromodel. The experimental results indicate that this non-monotonic, non-Fickian transport is saturation- and flow-rate-dependent. Using real-time visualization of the resident concentration (averaged concentration over a representative elementary volume of the pore network), we directly estimated the hydrodynamically stagnant (immobile) zones and the mass transfer between mobile and immobile zones. We identified (a) the nonlinear contribution of the immobile zones to the non-Fickian transport under transient transport conditions and (b) the non-monotonic fate of immobile zones with respect to saturation under single and two fluid-phase conditions in a micromodel. These two findings highlight the serious flaws in the assumptions of the conventional mobile-immobile model (MIM), which is commonly used to characterize the transport under two fluid-phase conditions.

In the last few decades, micro-models have become popular experimental tools for two-phase flow studies. In this work, the design and fabrication of an innovative, elongated, glass-etched micro-model with dimensions of 5 × 35 mm(2) and constant depth of 43 microns is described. This is the first time that a micro-model with such depth and dimensions has been etched in glass by using a dry etching technique. The micro-model was visualized by a novel setup that allowed us to monitor and record the distribution of fluids throughout the length of the micro-model continuously. Quasi-static drainage experiments were conducted in order to obtain equilibrium data points that relate capillary pressure to phase saturation. By measuring the flow rate of water through the flow network for known pressure gradients, the intrinsic permeability of the micro-model's flow network was also calculated. The experimental results were used to calibrate a pore-network model and test its validity. Finally, we show that glass-etched micro-models can be valuable tools in single and/or multi-phase flow studies and their applications.