Search

Ethane is the second largest component among natural gas, and the detection of ethane is an effective method for rapid identification of the leakage of the natural gas pipelines. In this work, a homogeneous sampling membrane inlet was developed and coupled with the homemade photoelectron ionization miniature time-of-flight mass spectrometer (PEI-mini-TOFMS) for in situ, on-line and highly sensitive ethane detection. The membrane area of the homogeneous sampling membrane inlet was increased from 490 mm 2 to 1256 mm 2 , gaseous sample is injected from the top port and flowed through the membrane surface and out of the bottom two ports, with the three ports arranged in a triangular shape. The highest average flow velocity of the gas on the surface of the membrane reached 0.4 m s -1 , and the optimal gas pressure in the PEI source was enhanced from 2.2 Pa to 4.0 Pa with this new design. The new design improved the comprehensive sensitivity of ethane by a factor of 3.0 compared with that of the traditional two-hole membrane inlet with the membrane area of 490 mm 2 . The semiconductor cold trap controlled the sample relative humidity (RH) at 10-12%, enabling direct sampling for highly sensitive analysis with RH as high as 70% and temperature from 7 °C to 40 °C. The quantitative range was 1-50 ppmv with a limit of detection (LOD, S/N = 3) lowered to 420 ppbv within 1 min, and zero humidity quantitative calibration with cold trap further reduced the relative standard deviation (RSD) of the signal intensities to 2.84%. The performance of the novel method developed in this work demonstrated a potential application on the above-ground natural gas pipelines leakage monitoring., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 Elsevier B.V. All rights reserved.)

Formic and acetic acids are the most abundant gaseous organic acids and play the key role in the atmospheric chemistry. In iodine-adduct chemical ionization mass spectrometry (CIMS), the low utilization efficiency of methyl iodide and humidity interference are two major issues of the vacuum ultraviolet (VUV) lamp initiated CIMS for on-line gaseous formic and acetic acids analysis. In this work, we present a new CIMS based on VUV lamp, and the ion-molecular reactor is separated into photoionization and chemical ionization zones by a reducer electrode. Acetone was added to the photoionization zone, and the VUV photoionization acetone provided low-energy electrons for methyl iodide to generate I - , and the addition of acetone reduced the amount of methyl iodide by 2/3. In the chemical ionization zone, a headspace vial containing ultrapure water was added for humidity calibration, and the vial changes the sensitivity as a function of humidity from ambiguity to well linear correlation (R 2 > 0.95). With humidity calibration, the CIMS can quantitatively measure formic and acetic acids in the humidity range of 0%-88% RH. In this mode, limits of detection of 10 and 50 pptv are obtained for formic and acetic acids, respectively. And the relative standard deviation (RSD) of quantitation stability for 6 days were less than 10.5%. This CIMS was successfully used to determine the formic and acetic acids in the underground parking and ambient environment of the Shandong University campus (Qingdao, China). In addition, we developed a simple model based formic acid concentration to assess vehicular emissions., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024. Published by Elsevier B.V.)

Single photon ionization (SPI) based on vacuum ultraviolet (VUV) lamps has been extensively investigated and applied due to its clean mass spectra as a soft ionization method. However, the photon energy of 10.6 eV and photon flux of 10 11 photons s -1 of a commercial VUV lamp limits its range of ionizable analytes as well as its sensitivity. This work designs a chemical ionization focusing integrated (CIFI) ionization source time-of-flight mass spectrometry (TOFMS) based on a VUV lamp for the detection of volatile organic compounds (VOCs) and oxygenated volatile organic compounds (OVOCs). The photoelectrons obtained from the VUV lamp via the photoelectric effect ionized the oxygen and water in the air to obtain the reagent ions. The ion-molecule-reaction region (IMR) is constituted by a segmented quadrupole that radially focuses the ions using a radio-frequency electric field. This significantly enhances the yield and transport efficiency of the product ions leading to a great improvement in sensitivity. As a result, a 44-fold and 1154-fold increase in the signal response for benzene and pentanal were achieved, respectively. To verify the reliability of the ionization source, the linear correspondence and repeatability of benzene and pentanal were investigated. Satisfactory dynamic linearity was obtained in the mixing ratio range of 5-50 ppbv, and the relative standard deviation (RSD) of inter-day reached 3.91% and 6.26%, respectively. Finally, the CIFI-TOFMS was applied to the determination of OVOCs, and the LOD of 12 types of OVOCs reached the pptv level, indicating that the ionization source has the potential for accurate and sensitive online monitoring of atmospheric OVOCs.

Formamide has been classified as a Class 1B reproductive toxicant to children by the European Union (EU) Chemicals Agency. Foam mats are a potential source of formamide and ammonia. Online dopant-assisted atmospheric pressure photoionization time-of-flight mass spectrometry (DA-APPI-TOFMS) coupled with a Teflon environmental chamber was developed to assess the exposure risk of formamide and ammonia from foam mats to children. High levels of formamide (average 3363.72 mg/m 3 ) and ammonia (average 1586.78 mg/m 3 ) emissions were measured from 21 foam mats with three different raw material types: ethylene-vinyl acetate (EVA: n = 7), polyethylene (PE: n = 7), and cross-linked polyethylene (XPE: n = 7). The 28 day emission testing for the selected PE mat showed that the emissions of formamide were 2 orders of magnitude higher than the EU emission limit of 20 μg/m 3 , and formamide may be a permanent indoor contaminant for foam mat products during their life cycle. The exposure assessment of children aged 0.5-6 years showed that the exposure dose was approximately hundreds of mg/kg-day, and the age group of 0.5-2 years was subject to much higher dermal exposures than others. Thus, this study provided key relevant information for further studies on assessing children's exposure to indoor air pollution from foam mats.

Natural gas pipeline leakage seriously endangers people's lives and properties, and there is an urgent need for on-site, rapid, and accurate locating the leakage point of the underground natural gas pipeline. Here, we added neon gas to natural gas pipelines as a tracer gas, and used a miniature time-of-flight mass spectrometry (mini-TOFMS) to on-site detect neon gas to quickly locate the leak point of underground natural gas pipelines. The mini-TOFMS used capillary tube sampling to directly analyze the leaked neon gas without sample preparation, and the analysis time of a single sample was only 60 s, which was less than one-seventeenth that of traditional off-line gas chromatography (GC) method. The mini-TOFMS exhibited a linear response range from 69 ppmv to 3.0 × 10 5 ppmv with the limit of detection (LOD, S/N = 3) of 19.0 ppmv. The correlation of GC and mini-TOFMS for Ne quantitative analysis was as high as 0.98. The performance of the newly designed method with the mini-TOFMS was demonstrated by on-site locating the underground natural gas pipeline leakage point in the experimental station. And leakage point of the natural gas pipeline, especially for those pipelines with different gas pressure buried under the same road, can be found more efficiently and accurately., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2022 Elsevier B.V. All rights reserved.)

Amines in fine particles constitute a significant fraction of secondary organic aerosols and have adverse effects on air quality and human health. To understand the chemical composition, variation characteristics, and potential sources of fine particulate amines in the coastal area in northern China, field sampling and chemical analysis were conducted in coastal Qingdao in the winter of 2018 and 2019. A total of 15 major amines were identified and quantified by using an ultra-high-performance liquid chromatography coupled with mass spectrometry. The average concentration of total amines in PM 2.5 samples was approximately 130 ng m -3 . Dimethylamine was the most abundant species with average fractions of 44.8% and 65.0% in the quantified amines during the two field campaigns, followed by triethylamine (22.9% and 8.7%) and methylamine (8.3% and 4.4%). The amines in PM 2.5 usually exhibited elevated concentrations in the presence of high levels of SO 2 and NO x or in the condition of high relative humidity. A receptor model of positive matrix factorization was employed and seven major sources were identified, including coal combustion, industrial production, vehicle exhaust, biomass burning, agricultural activities, secondary formation, and marine emission. Surprisingly, most of 15 amines in fine particles primarily originated from the primary emissions of anthropogenic activities particularly related to coal combustion and industrial productions, which should be given close concern to address the amine pollution., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2022 Elsevier B.V. All rights reserved.)

In the operation using sevoflurane as an anesthetic, some patients, especially children, will have agitation symptoms after awakening from anesthesia. The incidence of agitation is about 20%, and current detection methods cannot predict the probability of a patient with agitation. In this paper, a magnetic field enhanced photoelectron ionization (MEPEI) miniature time-of-flight mass spectrometer (TOFMS) was developed for point-of-care detection and verification of the relationship between postoperative agitation symptoms and sevoflurane concentration in exhaled breath. The MEPEI source is water vapor resistant and can directly ionize sevoflurane via capillary sampling and obtain its characteristic ion [C 4 H 3 F 6 O] + ( m / z 181), and the analysis time of exhaled breath is only 60 s. Three standard curves of 0.5-80 ppmv, 80-2000 ppmv and 2000-15 000 ppmv were formulated to quantitatively detect sevoflurane in different scenarios, the coefficient of determination ( R 2 ) was higher than 0.9882 and the relative standard deviation (RSD) of signal intensity was only 1.24%. The results indicated that four of the 46 child patients had agitation symptoms. Partial least squares-discriminant analysis (PLS-DA) was performed to analyze the data, and an identification and treatment strategy was established for child patients with agitation symptoms. The new miniature MEPEI-TOFMS was also successfully used to evaluate the concentration of sevoflurane in a medical environment. The real-time monitoring of sevoflurane concentration in exhalation indicates the potential of this method for low-cost and convenient point-of-care (POC) detection and diagnosis of agitation symptoms.

Ammonia (NH 3 ) is ubiquitous in the atmosphere, it can affect the formation of secondary aerosols and particulate matter, and cause soil eutrophication through sedimentation. Currently, the use of radioactive primary reagent ion source and the humidity interference on the sensitivity and stability are the two major issues faced by chemical ionization mass spectrometer (CIMS) in the analysis of atmospheric ammonia. In this work, a vacuum ultraviolet (VUV) Kr lamp was used to replace the radioactive source, and acetone was ionized under atmospheric pressure to obtain protonated acetone reagent ions to ionize ammonia. The ionization source is designed as a separated three-zone structure, and even 90 vol.% high-humidity samples can still be directly analyzed with a sensitivity of sub-ppbv. A signal normalization processing method was designed, and with this new method, the quantitative relative standard deviation (RSD) of the instrument was decreased from 17.5% to 9.1%, and the coefficient of determination was increased from 0.8340 to 0.9856. The humidity correction parameters of the instrument were calculated from different humidity, and the ammonia concentrations obtained under different humidity were converted to its concentration under zero humidity condition with these correction parameters. The analytical time for a single sample is only 60 sec, and the limit of detection (LOD) was 8.59 pptv (signal-to-noise ratio S/N = 3). The ambient measurement made in Qingdao, China, in January 2021 with this newly designed CIMS, showed that the concentration of ammonia ranged from 1 to 130 ppbv., (Copyright © 2021. Published by Elsevier B.V.)

Trimethylamine (TMA) is ubiquitous in the marine systems and may affect atmospheric chemistry as a precursor and strong stabilizer of atmospheric secondary aerosol, influencing cloud formation. Rapid and accurate measurement of the concentration of TMA in seawater is challenging due to their polarity, aqueous solubility, volatility and existence at low concentrations in marine environments. In this study, a dopant-assisted atmospheric pressure photoionization time-of-flight mass spectrometry (DA-APPI-TOFMS) coupled with a dynamic purge-release method was developed for rapid and sensitive analysis of TMA in seawater. A novel three-zones ionization source has been developed for improving the ionization efficiency of analyte molecules and minimizing the influence of high-humidity of the sample gas, which allowed direct analysis of high-humidity (RH> 90%) gas samples from microbubble purging process by the mass spectrometer. At atmospheric pressure, the three-zones ionization source allows the use of high-speed purge gas to quickly purge all organic amines dissolved in the water into the gas phase, ensuring quantitative accuracy. The limit of quantification (LOQ) for TMA down to 0.1 μg L -1 was obtained in less than 2 min by consuming only 2 mL seawater sample. This method was applied for the determination of the concentrations of TMA in the coastal seawater to validate its practicability and reliability for analysis of trace amines in marine environments., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2020 Elsevier B.V. All rights reserved.)

Gas-insulated switchgear (GIS) is widely used across multiple electric stages and different power grid levels. However, the threat from several inevitable faults in the GIS system surrounds us for the safety of electricity use. In order to improve the evaluation ability of GIS system safety, we propose an efficient strategy by using machine learning to conduct SF 6 decomposed components analysis (DCA) for further diagnosing discharge fault types in GIS. Note that the empirical probability function of different faults fitted by the Arrhenius chemical reaction model has been investigated into the robust feature engineering for machine learning based GIS diagnosing model. Six machine learning algorithms were used to establish models for the severity of discharge fault and main insulation defects, where identification algorithms were trained by learning the collection dataset composing the concentration of the different gas types (SO 2 , SOF 2 , SO 2 F 2 , CF 4 , and CO 2 , etc.) in the system and their ratios. Notably, multiple discharge fault types coexisting in GIS can be effectively identified based on a probability model. This work would provide a great insight into the development of evaluation and optimization on solving discharge fault in GIS.

One of the most abundant biological volatile organic compounds (BVOCs) in the atmosphere, monoterpene, is characterized by its short lifetime, low concentration, fast temporal and spatial variations, and wide variety of isomers. In this study, a multi-capillary column (MCC) was combined with high-pressure photoionization time-of-flight mass spectrometry (HPPI-TOF MS) and employed to develop an MCC-HPPI-TOF MS combination instrument as an online two-dimensional gas chromatography-mass spectrometry (GC-MS) method for the rapid qualitative and quantitative analysis of monoterpene isomers. As a result, six monoterpene isomers, α -pinene, β -pinene, α -terpinene, γ -terpinene, 3-carene, and limonene, were successfully isolated in 180 s with limits of detection (LODs) as low as 6 μg/m 3 without sample pre-enrichment. This method was successfully applied to the rapid online analysis of monoterpenes released from the branches and leaves of Cedrus atlantica and Sabina chinensis , which shows the capability and potential application of the method for the online detection of complex sample mixtures in environmental monitoring, process analysis, and other fields.

The increasing demand for rapid and sensitive roadside identification of trace illegal drugs drives the development of high-performance miniature mass spectrometric instrumentation and methodology. Here, we report a synchronized flash-thermal-desorption purging and ion injection (SFTDPI) method to increase the sensitive and rapid screening of volatile and nonvolatile illegal drugs for miniature ion trap mass spectrometry (ITMS). The flash-thermal desorption could reach 290 °C in 2.5 s, which could achieve efficient vaporization of nonvolatile noscapine with boiling point at 565 °C. ITMS using discontinuous atmospheric pressure interface (DAPI) has an ion utilization ratio of less than 1%, the synchronized purging for flash-thermal desorption and ion injection with DAPI could accurately control the time interval along with the desorption, gas purging, ionization and ion injection, and the sample utilization ratio increases more than five times. The miniature SFTDPI-ITMS presents good performance: (1) more than 60 times improvement in sensitivity was achieved compared to the previously reported thermal-desorption acetone-assisted photoionization ion trap mass spectrometer for nonvolatile drugs, and the minimum detectable quantity reaches 50 pg for fentanyl. (2) Ten kinds of mixing drugs with boiling point difference of 300 °C can be simultaneously identified within 3 s under a single analysis. SFTDPI-ITMS was deployed at the roadside checkpoint of Sino-Burmese border; fentanyl in the captured encapsulated powder and the suspected opiate had been successfully identified.

Illegal drug smugglings and crimes have long been a global concern, and an apparatus which can identify drugs on-the-spot is urgently demanded by law enforcement. A thermal desorption acetone-assisted photoionization miniature ion trap mass spectrometer was developed for on-site and rapid identification of illegal drugs at checkpoints. Acetone was chosen for dopant-assisted photoionization, and the sensitivity of selected drugs was further enhanced with protonated analyte molecular ions [M + H] + . For example, the sensitivity of ephedrine was improved by as high as 22-fold. The mass discrimination effect, which was usually considered as a shortcoming of ion trap mass analyzer, was ingeniously utilized to eliminate the protonated acetone reagent ions and maximize the trapping efficiency of analyte ions in mass analyzer. Twenty-seven drugs were analyzed, and the limits of detection (LODs) of selected illegal drugs were at the nanogram level with analysis time of 2 s. Analyte/dopant ion peak intensity ratios in mass spectra could be used for quantitation to improve the quantitative analysis performance of miniature ion trap mass spectrometer equipped with a discontinuous atmospheric pressure interface (DAPI) with the prerequisite that dopant ions and analyte ions could be simultaneously and effectively trapped by the ion trap. The RSD of signal intensity was reduced from 25.3% to 8.5%, and the linear range was extended from 0.5-25 to 0.5-100 ng/μL for methamphetamine. A temperature-resolved thermal desorption sampling strategy was developed and used to distinguish illegal drug components in plant-based drug samples and drinks containing illegal drugs.

Methanol-to-olefins (MTO) is a very important industrial catalysis technique for the production of light olefins, which is of great economic value and strategic significance. However, it is a great challenge for the traditional analytical methods to obtain the real-time information of product variation during MTO reaction process, which is vital for the conversion process research and mechanism explanation. In this study, a single photon ionization time-of-flight mass spectrometry (SPI-TOFMS) based on a windowless RF-discharge (WLRF) lamp was developed for real-time measurement of catalytic product during the initial stage of MTO reaction. The vacuum ultraviolet (VUV) photon energy was easily adjusted by changing the discharge gas. Argon (Ar) gas was eventually adopted as the discharge gas, since it produces photons with appropriate energy of 11.6 eV and 11.8 eV for ionization of light olefin molecules. The detection sensitivities of ethylene and propylene were largely improved to a substantially similar level with limits of detection (LODs) down to 16.98 and 9.64 ppbv, respectively. The initial stage of MTO reaction was real-time monitored with a high temporal resolution of 0.5 s, revealing that ethylene was the first olefin product followed by propylene. The successful application of WLRF-SPI-TOFMS in the monitoring of MTO catalytic process indicated broad application prospects of this instrument in the industrial reaction process monitoring.

An in-source, helical membrane inlet single photon ionization time-of-flight mass spectrometry (SPI-TOFMS) has been developed to improve the detection sensitivity of trace volatile organic compounds (VOCs) in water. A helical winding membrane and a four-stage differential pumping system of TOFMS was designed to improve and maintain the vapor pressure of analyte, which is linearly associated with the sensitivity of SPI. The helical winding increased the length of the hollow fiber membrane (HFM) from 7 cm to 100 cm and the pressure inside of SPI source was elevated from 3.6 Pa to 28 Pa, and then the sensitivity was increased by 16, 34.7, 32.3, 17.9 and 13.9 times for benzene, ethyl tert-butyl ether (ETBE), aniline, p-xylene, and chlorobenzene (MCBz) respectively. The limits of quantitation (LOQs) of benzene, ETBE, aniline, p-xylene and MCBz were 0.014, 0.143, 0.556, 0.036, 0.025 μg L -1 respectively with a measurement time of 50 s, which were enhanced by more than one order of magnitude compared to our previous work (reference [32]). The in-source design of helical winding membrane i.e. putting the membrane inside the SPI source dramatically reduced the response time to 1.33 min. This system has been evaluated for VOCs in sewage water of different laboratory buildings and automatic monitoring the pollutants in sewage water from a biological laboratory building. The automatic continuous analysis of organic pollutants in water has very important significance and broad application prospect for online assessment of water quality., (Copyright © 2018 Elsevier B.V. All rights reserved.)

Small molecule metabolites are widely used as biomarkers in the research field of metabolomics for disease diagnosis and exposure assessment. As a readily available biofluid containing plenty of volatile organic metabolites (VOMs), urine is ideal for non-invasive metabolomic analysis; however, there is still lack of rapid analysis method for VOMs in urine. Here we report a kind of rapid method for urine analysis by employing high-pressure photon ionization time-of-flight mass spectrometry (HPPI-TOFMS) combined with dynamic purge-injection. Various types of metabolites, such as ketones, alcohols, acids, sulfides, pyrroles and amines were detected directly by simple acidification or alkalization of urines. It is noteworthy that nitrogen-containing compounds, especially polar amines, could be ultrasensitively measured without any derivatization. The analytical capability of the direct HPPI-MS technique was demonstrated by analyzing five valuable metabolites, i.e., toluene, 2,5-dimethylpyrrole, trimethlyamine, styrene, and p-xylene, which exhibited relatively low limits of detection, wide linear range and satisfactory repeatability. Being highly sensitive and humidity-friendly, the whole analytical procedure is easily operated in less than 6 min. Interestingly, a new biomarker 2,5-dimethylpyrrole was exclusively found in the smoker's urine sample besides toluene. The work presents a novel tool for rapid nontarget disease biomarkers screening or target monitoring of specific compounds through the investigation of volatile metabolites in urine., (Copyright © 2018 Elsevier B.V. All rights reserved.)

Direct mass spectrometric measurements of saturated hydrocarbons, especially small n-alkanes, remains a great challenge because of low basicity and lack of ionizable functional groups. In this work, a novel high-pressure photoelectron-induced O 2 + cation chemical ionization source (HPPI-OCI) at kPa based on a 10.6 eV krypton lamp was developed for a time-of-flight mass spectrometer (TOFMS). High-intensity O 2 + reactant ions were generated by photoelectron ionization of air molecules in the double electric field ionization region. The quasi-molecular ions, [M-H] + , of C3-C6 n-alkanes, gradually dominated in the mass spectra when the ion source pressure was elevated from 88 to 1080 Pa, with more than 3 orders of magnitude improvement in signal intensity. As a result, the achieved limits of detection were lowered to 0.14, 0.11, 0.07, and 0.1 ppbv for propane, n-butane, n-pentane, and n-hexane, respectively. The performance of the HPPI-OCI TOFMS was first demonstrated by analysis of exhaled small n-alkanes from healthy smokers and nonsmokers. Then the concentration variations of exhaled small n-alkanes of four healthy volunteers were analyzed after alcohol consumption to explore the alcohol-hepatoxicity-related oxidative stress. In summary, this work provides new insights for controlling the O 2 + -participating chemical ionization by adjusting the ion source pressure and develops a novel direct mass spectrometric method for sensitive measurements of mall n-alkanes.

A real-time dynamic measurements of ammonia (NH 3 ) is crucial for understanding the atmospheric nucleation process. A novel method was developed for on line monitoring at the sub-second time scale for the gaseous ammonia in ambient air for months, based on a positive inhaling ion mobility spectrometry (IMS) with a 63 Ni ion source. The selective detection of NH 3 was achieved using a high resolution IMS with an optimization of the drift tube temperature above 150°C. This method improved the peak-to-peak resolution significantly, thus avoided the interferences of the adjacent peaks to the quantitative analysis of NH 3 . The time resolution of the IMS was less than 0.1s at a data averaging of 10 times. The limit of detection (LOD) achieved at sub-ppb level while a linear response of peak intensity versus concentration of NH 3 in the range of 10-60ppb and 60-400ppb were obtained. The relative standard deviations (RSD), the confidence level and the errors were 1.06%, 95% and ± 0.21ppb by measuring 100ppb NH 3 for 100 times. The effect of ambient humidity could be greatly reduced by using the drift temperature of over 150°C. At last, the application of measuring the NH 3 concentration evolutions of Dalian city was performed from June 19 to December 3 in 2015. The results illustrated a potential method of using IMS for a real-time measuring atmospheric NH 3 at an unprecedented accuracy and sensitivity with long-term stability., (Copyright © 2017 Elsevier B.V. All rights reserved.)

Chlorinated benzenes are typical precursors and indicators for polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) emissions from waste incinerators. Online and real-time monitoring of chlorobenzenes is a challenge due to their low concentration and complex nature of the flue gas. In this work, a continuous online monitoring system was built for detection of trace chlorinated benzenes based on a time-of-flight mass spectrometer (TOFMS). A single photon ionization (SPI) source based on a radiofrequency-excited windowless vacuum ultraviolet (VUV) lamp was developed for the first time to eliminate the signal attenuation resulting from the contamination of magnesium fluoride windows and to avoid the fragment ions. An automatic enrichment system including three parallel Tenax TA adsorption tubes was designed and coupled to the TOFMS to achieve the required ultrahigh sensitivity. The limits of quantitation at 7.65, 5.37 and 6.77pptv were obtained for monochlorobenzene (MCBz), dichlorobenzene (DCBz) and trichlorobenzene (TrCBz), respectively, within a 29-min analytical period. Moreover, this apparatus was applied to continuously online monitor the actual flue gas from a waste incinerator for three months. During this period, the concentrations of MCBz, DCBz and TrCBz detected in the flue gas were in the range of 100-1200, 50-800 and 50-300pptv, respectively. The relative standard deviation (RSD) of the sensitivity for the windowless VUV lamp ion source was 9.71% evaluated by the internal standard benzene over the 3-months flue gas monitoring. These results demonstrated the capability of this method in long-term analysis of the trace chlorinated benzenes in the flue gas., (Copyright © 2016 Elsevier B.V. All rights reserved.)

Photon ionization mass spectrometry (PI-MS) is a widely used technique for the online detection of trace substances in complex matrices. In this work, a new high-pressure photon ionization (HPPI) ion source based on a vacuum ultraviolet (VUV) Kr lamp was developed for time-of-flight mass spectrometry (TOFMS). The detection sensitivity was improved by elevating the ion source pressure to about 700 Pa. A radio frequency (RF)-only quadrupole was employed as the ion guide system following the HPPI source to achieve high ion transmission efficiency. In-source collision induced dissociation (CID) was conducted for accurate chemical identification by varying the voltage between the ion source and the ion guide. The high humidity of the breath air can promote the detection of some compounds with higher ionization potentials (IPs) that could not be well detected by single photon ionization (SPI) at low pressure. Under 100% relative humidity (37 °C), the limits of detection down to 0.015 ppbv (parts per billion by volume) for aliphatic and aromatic hydrocarbons were obtained. This HPPI-TOFMS system was preliminarily applied for online investigations of the exhaled breath from both healthy nonsmoker and smoker subjects, demonstrating its analytical capacity for complicated gases analysis. Subsequently, several frequently reported VOCs in the breath of healthy volunteers, i.e., acetone, isoprene, 2-butanone, ethanol, acetic acid, and isopropanol, were successfully identified and quantified.

Rationale: Sulfur hexafluoride (SF6 ) gas-insulated switchgear (GIS) is an essential piece of electrical equipment in a substation, and the concentration of the SF6 decomposition products are directly relevant to the security and reliability of the substation. The detection of SF6 decomposition products can be used to diagnosis the condition of the GIS., Methods: The decomposition products of SO2 , SO2 F2 , and SOF2 were selected as indicators for the diagnosis. A suitcase time-of-flight mass spectrometer (TOFMS) was designed to perform online GIS failure analysis. An RF VUV lamp was used as the photoelectron ion source; the sampling inlet, ion einzel lens, and vacuum system were well designed to improve the performance., Results: The limit of detection (LOD) of SO2 and SO2 F2 within 200 s was 1 ppm, and the sensitivity was estimated to be at least 10-fold more sensitive than the previous design. The high linearity of SO2 , SO2 F2 in the range of 5-100 ppm has excellent linear correlation coefficient R(2) at 0.9951 and 0.9889, respectively., Conclusions: The suitcase TOFMS using orthogonal acceleration and reflecting mass analyzer was developed. It has the size of 663 × 496 × 338 mm and a weight of 34 kg including the battery and consumes only 70 W. The suitcase TOFMS was applied to analyze real decomposition products of SF6 inside a GIS and succeeded in finding out the hidden dangers. The suitcase TOFMS has wide application prospects for establishing an early-warning for the failure of the GIS. Copyright © 2016 John Wiley & Sons, Ltd., (Copyright © 2016 John Wiley & Sons, Ltd.)

The specific locations of the double bonds in linear olefins can facilitate olefin catalytic synthetic reactions to improve the quality of target olefin products. We developed a simple and efficient approach based on single photon ionization time-of-flight mass spectrometry (SPI-TOFMS) combined with online ozonolysis to identify and quantify the linear olefin double bond positional isomers. The online ozonolysis cleaved the olefins at the double bond positions that led to formation of corresponding characteristic aldehydes. The aldehydes were then detected by SPI-TOFMS to achieve unique spectrometric "fingerprints" for each linear olefin to successfully identify the isomeric ones. To accurately quantify the isomeric components in olefin mixtures, an algorithm was proposed to quantify three isomeric olefin mixtures based on characteristic ion intensities and their equivalent ionization coefficients. The relative concentration errors for the olefin components were lower than 2.5% while the total analysis time was less than 2 min. These results demonstrate that the online ozonolysis SPI-TOFMS has the potential for real-time monitoring of catalytic olefin synthetic reactions.

A dopant-assisted reactive low temperature plasma (DARLTP) probe was developed for sensitive and specific detection of explosives by a miniature rectilinear ion trap mass spectrometer. The DARLTP probe was fabricated using a T-shaped quartz tube. The dopant gas was introduced into the plasma stream through a side-tube. Using CH2Cl2 doped wet air as the dopant gas, the detection sensitivities were improved about 4-fold (RDX), 4-fold (PETN), and 3-fold (tetryl) compared with those obtained using the conventional LTP. Furthermore, the formation of [M + (35)Cl](-) and [M + (37)Cl](-) for these explosives enhanced the specificity for their identification. Additionally, the quantities of fragment ions of tetryl and adduct ions such as [RDX + NO2](-) and [PETN + NO2](-) were dramatically reduced, which simplified the mass spectra and avoided the overlap of mass peaks for different explosives. The sensitivity improvement may be attributed to the increased intensity of reactant ion [HNO3 + NO3](-), which was enhanced 4-fold after the introduction of dopant gas. The limits of detection (LODs) for RDX, tetryl, and PETN were down to 3, 6, and 10 pg, respectively. Finally, an explosive mixture was successfully analyzed, demonstrating the potential of the DARLTP probe for qualitative and quantitative analysis of complicated explosives.

Single-photon ionization mass spectrometry (SPI-MS) is a versatile and powerful analytical technique for online and real-time analysis of organic species; however, it is confronted with an intrinsic drawback of lacking structural information on the investigated molecules, let alone differentiation of isobaric compounds. In this work, we describe a first attempt to integrate in-source collision-induced dissociation (CID) to the SPI ion source in a SPI-MS instrument. The in-source CID was accomplished by elevating the pressure in the ion source to medium vacuum pressure (MVP) and raising the extraction voltage. With the aid of in-source CID, both the SPI-induced molecular ion and CID-generated fragment ion mass spectra can be obtained to endue each analyte with its unique spectrometric "fingerprint". The capability for differentiation of isobaric compounds is demonstrated by analyzing two groups of isobaric compounds with molecular weights of 72 and 106 Da, respectively, and quantitative analysis of p-xylene and ethylbenzene in gas mixture. As a result, isobaric compounds with different characteristic fragment ions or appearance energies can be successfully distinguished. The work presents a feasible method for practical applications of SPI-MS to differentiate isobaric compounds conveniently and rapidly without MS/MS technique or coupling additional separation technologies.

A novel analytical method coupling gas chromatography (GC) with single photon ionization time-of-flight mass spectrometry (SPI-TOF MS) has been developed. First of all, a double-wall-tube transfer line was built to combine GC with SPI-TOF MS, which realized seamless connection between GC and SPI ion source. Based on this, standard n-pentadecane and benzene/toluene/xylene standard gas mixtures were used to study important voltage parameters of the ion source. After the optimization of the ion source voltages, pure molecular ion peaks of the analytes were obtained in the mass spectra and qualitative analysis of different kinds of organic compounds were eventually realized rapidly and accurately. At last, GC/SPI-TOF MS was applied to the characterization of volatile and semvolatile organic compounds in diesel and two-dimensional spectra of GC×SPI-TOF MS were obtained. Without complicated spectra interpretation and data processing, volatile and semi-volatile organic compounds in diesel have been classified qualitatively by ion mass-to-charge ratio (m/z) in SPI mass spectra, including aliphatic compounds, aromatic compounds and nitrogen-containing compounds with low concentration such as benzopyrroles. Isomeric compounds in diesel were separated and identified by retention times of chromatographic peaks. The results indicate that the proposed analytical method of GC/SPI-TOF MS is suitable for the characterization of complicated samples such as diesel and environmental pollutants with easy operation and high efficiency.

A vacuum ultraviolet lamp based single photon ionization- (SPI-) photoelectron ionization (PEI) portable reflecting time-of-flight mass spectrometer (TOFMS) was designed for online monitoring gas samples. It has a dual mode ionization source: SPI for analyte with ionization energy (IE) below 10.6 eV and PEI for IE higher than 10.6 eV. Two kinds of sampling inlets, a capillary inlet and a membrane inlet, are utilized for high concentration and trace volatile organic compounds, respectively. A mass resolution of 1100 at m/z 64 has been obtained with a total size of 40 × 31 × 29 cm, the weight is 27 kg, and the power consumption is only 70 W. A mixture of benzene, toluene, and xylene (BTX), SO2, and discharging products of SF6 were used to test its performance, and the result showed that the limit of quantitation for BTX is as low as 5 ppbv (S/N = 10 : 1) with linear dynamic ranges greater than four orders of magnitude. The portable TOFMS was also evaluated by analyzing volatile organic compounds from wine and decomposition products of SF6 inside of a gas-insulated switchgear.

A nanoelectrospray ionization ion mobility spectrometer (nanoESI-IMS) working at ambient pressure and ambient temperature was developed as a detector of high performance liquid chromatography (HPLC) to achieve sensitive detection of amines with no derivatization and meanwhile provide another dimension of separation. The easier desolvation property of the charged droplets formed in nanoESI source enabled complete desolvation of the product ions of sixteen amines and drugs using the nanoESI-IMS at ambient temperature. Working at ambient temperature was good for suppressing the dissociation of thermal volatile ions, such as only the proton adducted molecular ions were observed for morphine in the nanoESI-IMS. Besides, the resolving power of the nanoESI-IMS also showed an increasing tendency as lowering the working temperature, an increment of 19 percent and 10 percent was observed for diethylamine and triethylamine as the temperature dropped from 92°C to 32°C. The resolving power of the nanoESI-IMS at 32°C for the 16 tested compounds was amid 33-44. With the nanoESI-IMS coupled to HPLC, a six-compound mixture including isomers was successfully separated and detected without any derivatization. And linear response ranges of 1 to 20, 0.5 to 20, and 0.8 to 20μgml(-1) and limits of detection of 0.25, 0.15, and 0.17μgml(-1) for triethylamine, diethylamine, and butylamine, respectively, were obtained with the hyphenated system. These results showed the excellent performance of the two-dimensional separation and detection method in direct qualitative and quantitative analyses of amines., (Copyright © 2014 Elsevier B.V. All rights reserved.)

With respect to massive consumption of ammonia and rigorous industrial synthesis conditions, many studies have been devoted to investigating more environmentally benign catalysts for ammonia synthesis under moderate conditions. However, traditional methods for analysis of synthesized ammonia (e.g., off-line ion chromatography (IC) and chemical titration) suffer from poor sensitivity, low time resolution, and sample manipulations. In this work, charge-transfer ionization (CTI) with O2(+) as the reagent ion based on a vacuum ultraviolet (VUV) lamp in a time-of-flight mass spectrometer (CTI-TOFMS) has been applied for real-time monitoring of the ammonia synthesis in a microreactor. For the necessity of long-term stable monitoring, a self-adjustment algorithm for stabilizing O2(+) ion intensity was developed to automatically compensate the attenuation of the O2(+) ion yield in the ion source as a result of the oxidation of the photoelectric electrode and contamination on the MgF2 window of the VUV lamp. A wide linear calibration curve in the concentration range of 0.2-1000 ppmv with a correlation coefficient (R(2)) of 0.9986 was achieved, and the limit of quantification (LOQ) for NH3 was in ppbv. Microcatalytic synthesis of ammonia with three catalysts prepared by transition-metal/carbon nanotubes was tested, and the rapid changes of NH3 conversion rates with the reaction temperatures were quantitatively measured with a time resolution of 30 s. The high-time-resolution CTI-TOFMS could not only achieve the equilibrium conversion rates of NH3 rapidly but also monitor the activity variations with respect to investigated catalysts during ammonia synthesis reactions.

Ion mobility spectrometry (IMS) has become the most deployed technique for on-site detection of trace explosives, and the reactant ions generated in the ionization source are tightly related to the performances of IMS. Combination of multiform reactant ions would provide more information and is in favor of correct identification of explosives. Fast switchable CO3(-)(H2O)n and O2(-)(H2O)n reactant ions were realized in a dopant-assisted negative photoionization ion mobility spectrometer (DANP-IMS). The switching could be achieved in less than 2 s by simply changing the gas flow direction. Up to 88% of the total reactant ions were CO3(-)(H2O)n in the bidirectional mode, and 89% of that were O2(-)(H2O)n in the unidirectional mode. The characteristics of combination of CO3(-)(H2O)n and O2(-)(H2O)n were demonstrated by the detection of explosives, including 2,4,6-trinitrotoluene (TNT), cyclo-1,3,5-trimethylene-2,4,6-trinitramine (RDX), ammonium nitrate fuel oil (ANFO), and black powder (BP). For TNT, RDX, and BP, product ions with different reduced mobility values (K0) were observed with CO3(-)(H2O)n and O2(-)(H2O)n, respectively, which is a benefit for the accurate identification. For ANFO, the same product ions with K0 of 2.07 cm(2) V(-1) s(-1) were generated, but improved peak-to-peak resolution as well as sensitivity were achieved with CO3(-)(H2O)n. Moreover, an improved peak-to-peak resolution was also obtained for BP with CO3(-)(H2O)n, while the better sensitivity was obtained with O2(-)(H2O)n.

An in-source, stretched, hollow fiber membrane (HFM) inlet has been developed to improve the sensitivity of on-line time-of-flight mass spectrometry (TOFMS) with a vacuum ultraviolet (VUV) lamp based single photon ionization (SPI) source for the direct analysis of liquid samples. A 2-cm HFM was stretched to 8 cm in length, and placed in the ion source and directly under the VUV lamp window with a distance of 15 mm. Compared with the conventional flow-through configuration under the same experimental conditions, the signal intensities of selected volatile organic compounds (VOCs) of methyl tert-butyl ether (MTBE), ethyl tert-butyl ether (ETBE), benzene, toluene and p-xylene were increased over 5-fold in magnitude, and the response time was shortened to one-third. The limits of detection (LOD) of MTBE, ETBE, benzene, toluene and p-xylene ranged from 0.25 to 1.3 μg L(-1) with a measurement time of 60 s, and three orders of linear range were obtained with correlation coefficients of 0.9972-0.9992. The present results suggest that the in-source stretched HFM is a simple and effective way to increase the sensitivity and shorten response time of the membrane inlet, and we believe that it will also be beneficial to other types of on-line mass spectrometer for the on-line analysis of VOCs in water with a VUV lamp based SPI ion source.

A platform consisting of a halogen lamp, a low temperature plasma (LTP) probe, and a miniature rectilinear ion trap mass spectrometer (RIT-MS) has been constructed and evaluated to detect organic and inorganic explosives on solid surfaces. This platform features two attractive characteristics: high sensitivity for the explosives with low volatility, and rapid analysis speed for the explosives on large surface areas. With non-contact heating by the halogen lamp, the signal intensities for the explosives with relatively high volatility were improved by over an order of magnitude, compared to those obtained at room temperature; and even more, the explosives with low volatility, which could hardly be detected at room temperature, were able to be readily identified. The limits of detection (LODs) of the selected explosives were all at the picogram level (e.g., 10 pg and 20 pg for TNT and RDX, respectively) with a heating time of 3 s. Using manual surface swabbing, the analysis of explosives on a large surface area (7.5 cm × 2.5 cm) was accomplished within 10 s, and an acceptable sensitivity could be acquired; additionally, inorganic explosives (black powder and firecracker) were successfully detected. Without any sample pretreatment, the platform was used to analyze the wastewater from an explosives factory, confirming the existence of 2,4,6-trinitrotoluene (TNT), 2,4-dinitrotoluene (2,4-DNT), and 2,6-dinitrotoluene (2,6-DNT), and the concentration of TNT was determined to be 5 ng mL(-1). All these results indicated that the proposed platform was a promising technique for security monitoring and environmental analysis.

Ion mobility spectrometry (IMS) is a key trace detection technique for explosives and the development of a simple, stable, and efficient nonradioactive ionization source is highly demanded. A dopant-assisted negative photoionization (DANP) source has been developed for IMS, which uses a commercial VUV krypton lamp to ionize acetone as the source of electrons to produce negative reactant ions in air. With 20 ppm of acetone as the dopant, a stable current of reactant ions of 1.35 nA was achieved. The reactant ions were identified to be CO(3)(-)(H(2)O)(n) (K(0) = 2.44 cm(2) V(-1) s(-1)) by atmospheric pressure time-of-flight mass spectrometry, while the reactant ions in (63)Ni source were O(2)(-)(H(2)O)(n) (K(0) = 2.30 cm(2) V(-1) s(-1)). Finally, its capabilities for detection of common explosives including ammonium nitrate fuel oil (ANFO), 2,4,6-trinitrotoluene (TNT), N-nitrobis(2-hydroxyethyl)amine dinitrate (DINA), and pentaerythritol tetranitrate (PETN) were evaluated, and the limits of detection of 10 pg (ANFO), 80 pg (TNT), and 100 pg (DINA) with a linear range of 2 orders of magnitude were achieved. The time-of-flight mass spectra obtained with use of DANP source clearly indicated that PETN and DINA can be directly ionized by the ion-association reaction of CO(3)(-) to form PETN·CO(3)(-) and DINA·CO(3)(-) adduct ions, which result in good sensitivity for the DANP source. The excellent stability, good sensitivity, and especially the better separation between the reactant and product ion peaks make the DANP a potential nonradioactive ionization source for IMS.

A home-made stir bar sorptive extraction (SBSE) apparatus was combined to a single photon ionization time-of-flight mass spectrometer (SPI-TOFMS) for rapid and sensitive determination of trace volatile organic compounds (VOCs) in water. The home-made SBSE bar, low-cost and disposable, was used for VOCs extraction. A thermal desorption (TD) device was designed to desorb the analytes from the SBSE bar, and a high throughput interface was developed to transfer the analytes into the ionization chamber of the SPI-TOFMS. The combination of large extraction volume of SBSE bar, and the direct measurement power of SPI-TOFMS enable a short analysis time for VOCs in water with high sensitivity, for example the limits of detection (LODs) were in the range of 7.4-11.1 ng L(-1) for benzene, toluene, and p-xylene (BTX) within 15 min. BTX aqueous solutions were chosen to demonstrate the quantitative capability, the linear range was from 0.05 to 100 μg L(-1) and the correlation coefficients were better than 0.996. The proposed method was successfully applied for the analysis of VOCs in urban river water.

A magnetic field enhanced photoelectron ionization (MEPEI) source combined with single photon ionization (SPI) was developed for an orthogonal acceleration time-of-flight mass spectrometer (oaTOFMS). A commercial radio frequency (rf) powered vacuum ultraviolet (VUV) lamp was used as SPI light source, and the photoelectrons generated by photoelectric effect were accelerated to induce electron ionization (EI). The MEPEI was obtained by applying a magnetic field of about 800 G with a permanent annular magnet. Compared to a nonmagnetic field photoelectron ionization source, the signal intensities for SO(2), SF(6), O(2), and N(2) in MEPEI were improved more than 2 orders with the photoelectron energy around 20 eV, while most of the characteristics of soft ionization still remained. Simulation with SIMION showed that the sensitivity enhancement in MEPEI was ascribed to the increase of the electron moving path and the improvement of the electrons transmission. The limits of detection for SO(2) and benzene were 750 and 80 ppbv within a detection time of 4 s, respectively. The advantages of the source, including broad range of ionizable compounds, reduced fragments, and good sensitivity with low energy MEPEI, were demonstrated by monitoring pyrolysis products of polyvinyl chloride (PVC) and the intermediate products in discharging of the SF(6) gas inpurity.

A less laborious, structure-simple, and performance-reliable printed circuit board (PCB) based Bradbury-Nielsen gate for high-resolution ion mobility spectrometry was introduced and investigated. The gate substrate was manufactured using a PCB etching process with small holes (Φ 0.1 mm) drilled along the gold-plated copper lines. Two interdigitated sets of rigid stainless steel spring wire (Φ 0.1 mm) that stands high temperature and guarantees performance stability were threaded through the holes. Our homebuilt ion mobility spectrometer mounted with the gate gave results of about 40 for resolution while keeping a signal intensity of over 0.5 nano-amperes.

A novel combined ion source based on a vacuum ultraviolet (VUV) lamp with both single photon ionization (SPI) and chemical ionization (CI) capabilities has been developed for an orthogonal acceleration time-of-flight mass spectrometer (oaTOFMS). The SPI was accomplished using a commercial 10.6 eV krypton discharge lamp with a photon flux of about 10(11) photons s(-1), while the CI was achieved through ion-molecule reactions with O(2)(+) reactant ions generated by photoelectron ionization at medium vacuum pressure (MVP). To achieve high ionization efficiency, the ion source pressure was elevated to 0.3 mbar and the photoionization length was extended to 36 mm. As a result, limits of detection (LODs) down to 3, 4, and 6 ppbv were obtained for benzene, toluene, and p-xylene in MVP-SPI mode, and values of 8 and 10 ppbv were obtained for toluene and chloroform, respectively, in SPI-CI mode. As it is feasible to switch between MVP-SPI mode and SPI-CI mode rapidly, this system is capable of monitoring complex organic mixtures with a wide range of ionization energies (IEs). The analytical capacity of this system was demonstrated by measuring dehydrogenation products of long-chain paraffins to olefins through direct capillary sampling and drinking water disinfection byproducts from chlorine through a membrane interface.

A new sampling wand concept for ion trap mass spectrometers equipped with discontinuous atmospheric pressure interfaces (DAPI) has been implemented. The ion trap/DAPI combination facilitates the operation of miniature mass spectrometers equipped with ambient ionization sources. However, in the new implementation, instead of transferring ions pneumatically from a distant source, the mass analyzer and DAPI are separated from the main body of the mass spectrometer and installed at the end of a 1.2 m long wand. During ion introduction, ions are captured in the ion trap while the gas in which they are contained passes through the probe and is pumped away. The larger vacuum volume due to the extended wand improves the mass analysis sensitivity. The wand was tested using a modified hand-held ion trap mass spectrometer without additional power or pumping being required. Improved sensitivity was obtained as demonstrated with nano-electrospray ionization (ESI), atmospheric pressure chemical ionization (APCI), and low temperature plasma (LTP) probe analysis of liquid, gaseous, and solid samples, respectively.

A novel bipolar ionization source based on a commercial vacuum-UV Kr lamp has been developed for ion mobility spectrometry (IMS), which can work in both negative and positive ion mode. Its reactant ions formed in negative ion mode were predominantly assigned to be O(3)(-)(H(2)O)(n), which is different from that of the (63)Ni source with purified air as carrier and drift gases. The formation of O(3)(-)(H(2)O)(n) was due to the production of ozone caused by ultraviolet radiation, and the ozone concentration was measured to be about 1700 ppmv by iodometric titration method. Inorganic molecules such as SO(2), CO(2), and H(2)S can be easily detected in negative ion mode, and a linear dynamic range of 3 orders of magnitude and a limit of detection (S/N = 3) of 150 pptv were obtained for SO(2). Its performance as a negative ion source was investigated by the detection of ammonium nitrate fuel oil explosive, N-nitrobis(2-hydroxyethyl)amine dinitrate, cyclo-1,3,5-trimethylene-2,4,6-trinitramine, and pentaerythritol tetranitrate (PETN) at 150 degrees C. The limit of detection was reached at 45 pg for PETN, which was much lower than the 190 pg using (63)Ni ion mobility spectrometry under the same experimental condition. Also, its performance as an ordinary photoionization source was investigated in detecting benzene, toluene, and m-xylene.

A novel membrane inlet interface coupled to a single-photon ionization (SPI) miniature time-of-flight mass spectrometer has been developed for on-line rapid measurement of volatile organic compounds (VOCs). The vacuum ultraviolet (VUV) light source for SPI was a commercial krypton discharge lamp with photon energy of 10.6 eV and photon flux of 10(10) photons/s. The experimental results showed that the sensitivity was 5 times as high as obtained with the traditional membrane inlet. The enrichment efficiency could be adjusted in the range of 10 to 20 times for different VOCs when a buffer cell was added to the inlet interface, and the memory effect was effectively eliminated. A detection limit as low as 25 parts-per-billion by volume (ppbv) for benzene has been achieved, with a linear dynamic range of three orders of magnitude. The rise times were 6 s, 10 s and 15 s for benzene, toluene and p-xylene, respectively, and the fall time was only 6 s for all of these compounds. The analytical capacity of this system was demonstrated by the on-line analysis of VOCs in single puff mainstream cigarette smoke, in which more than 50 compounds were detected in 2 s., (Copyright 2007 John Wiley & Sons, Ltd.)

The analytical solutions of the ideal model for gradient elution that ignores the influence of the solute concentration on the retention factor (k) were studied by using the method of characteristics for solving partial differential equations. It is found for any gradient profiles and solvent strength models used that the concentration of the solute will be discontinuous where the mobile-phase composition is. On a given characteristic curve, the product of the concentration and the retention factor is kept constant at the point where the concentration is continuous. At the point where the concentration is discontinuous, the product on the left side of this point is equal to that on the right side. We also discussed the basic equations to predict the retention time in gradient elution and introduced the injection time into them. For linear solvent strength stepwise and linear gradient elution, general expressions were proposed for the prediction and they can be used as the basis to derive others for specific gradient modes such as single linear, stepwise, and ladderlike gradients. For these modes, simple expressions to account for the band compression and the concentration change during the elution were also given.