Search

Purpose: Prior studies have indicated an impact of cardiac muscle viscoelasticity on systolic and diastolic functions. However, the studies of ventricular free wall viscoelasticity, particularly for that of right ventricles (RV), are limited. Moreover, investigations on ventricular passive viscoelasticity have been restricted to large animals and there is a lack of data on rodent species. To fill this knowledge gap, this study aims to develop a biaxial tester that induces high-speed physiological deformations to characterize the passive viscoelasticity of rat RVs., Methods: The biaxial testing system was fabricated so that planar deformation of rat ventricle tissues at physiological strain rates was possible. The testing system was validated using isotropic polydimethylsiloxane (PDMS) sheets. Next, viscoelastic measurements were performed in healthy rat RV free walls by equibiaxial cyclic sinusoidal loadings and stress relaxation., Results: The biaxial tester's consistency, accuracy, and stability was confirmed from the PDMS samples measurements. Moreover, significant viscoelastic alterations of the RV were found between sub-physiological (0.1 Hz) and physiological frequencies (1-8 Hz). From hysteresis loop analysis, we found as the frequency increased, the elasticity and viscosity were increased in both directions. Interestingly, the ratio of storage energy to dissipated energy (W d /W s ) remained constant at 0.1-5 Hz. We did not observe marked differences in healthy RV viscoelasticity between longitudinal and circumferential directions., Conclusion: This work provides a new experimental tool to quantify the passive, biaxial viscoelasticity of ventricle free walls in both small and large animals. The dynamic mechanical tests showed frequency-dependent elastic and viscous behaviors of healthy rat RVs. But the ratio of dissipated energy to stored energy was maintained between frequencies. These findings offer novel baseline information on the passive viscoelasticity of healthy RVs in adult rats., (© 2024. The Author(s) under exclusive licence to Biomedical Engineering Society.)

Waste-tire textile fibers (WTTF) represent a challenge for the recycling industry since there are currently very few alternatives for their use. In this study, an evaluation of the effect of a new additive developed in two granular formats from WTTF on the fatigue behavior of asphalt mixtures was performed. For the first format of the WTTF-based additive, its effect was evaluated on hot-mix asphalt (HMA), while for the second format of the additive, the effects were evaluated on stone mastic asphalt (SMA). This second format represents an alternative that allows for the total replacement of the cellulose stabilizing additive used in the reference mix. The evaluation of fatigue damage in the mixes was performed using the four-point bending beam (4PB) test specified in European standard EN 12697-24. The test results show that the asphalt mixtures manufactured with WTTF-based additives exhibited a higher capacity to resist load cycles before failure compared to the reference mixtures. Likewise, once the asphalt mixtures were evaluated in a pavement structure by means of an empirical mechanistic analysis, the pavement structures composed of asphalt mixtures with WTTF-based additives showed significant improvements in their durability for the different load axes evaluated. For an average thickness of 15 cm of asphalt mix of a pavement-type structure, the use of the WTTF additive increases the durability of the structures by up to 129% and 112% compared to the HMA and SMA reference mixtures, respectively. These results show that both formats of the WTTF-based admixture improve the fatigue damage resistance of the HMA and SMA asphalt mixtures.

This study explores the hysteresis phenomenon in DPPC (1,2-dipalmitoyl-sn-glycero-3-phosphocholine) monolayers, considering several variables, including temperature, compression and expansion rates, residence time, and subphase content. The investigation focuses on analyzing the influence of these variables on key indicators such as the π-A isotherm curve, loop area, and compression modulus. By employing the Langmuir-Blodgett technique, the findings reveal that all the examined factors significantly affect the aforementioned parameters. Notably, the hysteresis loop, representing dissipated energy, provides valuable insights into the monolayer's viscoelasticity, molecular packing, phase transition changes, and resistance during the isocycle process. These findings contribute to a comprehensive understanding of the structural and dynamic properties of DPPC monolayers, offering insights into their behavior under varying conditions. Moreover, the knowledge gained from this study can aid in the development of precise models and strategies for controlling and manipulating monolayer properties, with potential applications in drug delivery systems, surface coatings, as well as further investigation into air penetration into alveoli and the blinking mechanism.

Surrounding rock deformation and consequent support failure are the most prominent issues in red-bed rock tunnel engineering and are mainly caused by the effects of unloading, rheology, and swelling. This study investigated the mechanical responses of two kinds of red-bed mudstone and sandstone under unloading conditions via laboratory observation. Volume dilation was observed on the rocks during unloading, and the dilatancy stress was linear with the initial confining pressure. However, the ratios of dilatancy stress to peak stress of the two rocks kept at a range from 0.8 to 0.9, regardless of confining pressures. Both the elastic strain energy and the dissipated energy evolved synchronously with the stress-strain curve and exhibited conspicuous confining pressure dependence. Special attention was paid to the evolution behavior of the dilatancy angle. The dilatancy angle changed linearly during unloading. When the confining pressure was 10 MPa, the dilatancy angle of mudstone decreased from 26.8° to 12.5° whereas the dilatancy angle of sandstone increased from 34.6° to 51.1°; when the confining pressure rose to 25 MPa, the dilatancy angle of mudstone and sandstone decreased from 45.8° to 17.4° and increased from 21.7° to 39.5°, respectively. To further understand the evolution of the dilatancy angle, we discussed the links between the variable dilatancy angle and the processes of rock deformation and energy dissipation.

There has been little research on the impact resistance of mortar-rock slope protection structures. To ensure that the mortar-rock interface has good adhesion properties under the action of impact loading, in this paper, based on fracture mechanics theory, a theoretical impact model was established for mortar-rock binary material. Dynamic fracture tests were carried out on mortar-rock interfaces using the split-Hopkinson pressure bar (SHPB) system. The Brazilian disc (CSTBD) specimen was prepared with one half in granite and the other half in mortar. The specimen used for the dynamic impact test was 48 mm in diameter and 25 mm thick. The effects caused by the change in interface inclination and interface shape on the dynamic fracture mode were discussed. The dynamic model parameters were obtained for different inclination angles and interfaces. The results show that both the interface inclination and interface shape have significant effects on the dynamic mechanical properties of the mortar-rock binary material. The fracture modes of the mortar-rock specimens can be classified into three types. When the interface inclination is 0°, the specimen shows shear damage with an interface fracture; when the interface inclination is in the range of 0-90°, the dynamic splitting strength of the mortar-rock material increases with increasing interface inclination, and the interface undergoes composite fracture; and when the interface inclination is 90°, the dynamic splitting strength of the specimen reaches its peak, and the interface undergoes tensile fracture. The mortar-rock interface damage follows the M-C criterion. The roughness of the interface shape has a large influence on the dynamic splitting strength of the specimens. The rougher the interface shape, the higher the interface cleavage strength and the higher the peak load that causes the material to damage. The results of this study can provide a reference for the design of mortar-rubble structures to meet the demand for impact resistance and have strong engineering application value.

Introduction: The right ventricle (RV) mechanical property is an important determinant of its function. However, compared to its elasticity, RV viscoelasticity is much less studied, and it remains unclear how pulmonary hypertension (PH) alters RV viscoelasticity. Our goal was to characterize the changes in RV free wall (RVFW) anisotropic viscoelastic properties with PH development and at varied heart rates. Methods: PH was induced in rats by monocrotaline treatment, and the RV function was quantified by echocardiography. After euthanasia, equibiaxial stress relaxation tests were performed on RVFWs from healthy and PH rats at various strain-rates and strain levels, which recapitulate physiological deformations at varied heart rates (at rest and under acute stress) and diastole phases (at early and late filling), respectively. Results and Discussion: We observed that PH increased RVFW viscoelasticity in both longitudinal (outflow tract) and circumferential directions. The tissue anisotropy was pronounced for the diseased RVs, not healthy RVs. We also examined the relative change of viscosity to elasticity by the damping capacity (ratio of dissipated energy to total energy), and we found that PH decreased RVFW damping capacity in both directions. The RV viscoelasticity was also differently altered from resting to acute stress conditions between the groups-the damping capacity was decreased only in the circumferential direction for healthy RVs, but it was reduced in both directions for diseased RVs. Lastly, we found some correlations between the damping capacity and RV function indices and there was no correlation between elasticity or viscosity and RV function. Thus, the RV damping capacity may be a better indicator of RV function than elasticity or viscosity alone. These novel findings on RV dynamic mechanical properties offer deeper insights into the role of RV biomechanics in the adaptation of RV to chronic pressure overload and acute stress., Competing Interests: The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest., (Copyright © 2023 Liu, LeBar, Roth, Pang, Ayers, Chicco, Puttlitz and Wang.)

Background: Cartilage is a mechanically highly stressed tissue in the human body and an important part of synovial joints. The joint cartilage is lubricated by synovial fluid with hyaluronic acid (HA) as main component. However, in joints with osteoarthritis HA has a lower concentration and molecular weight compared to healthy joints. In recent years, the intra-articular injection of therapeutic HA lubricant, has become a popular therapy. The effect of HA application on the friction of a complete joint with physiological movement needs to be further determined., Methods: The aim of the present study was to evaluate the lubrication effect of the joint by three lubricants (NaCl, fetal calf serum (FCS) and HA) and their effect on the friction in nine complete ovine carpo-metacarpal joints. The joints were mounted on a material testing machine and a physiological movement with 10° rotation was simulated with ascending axial load (100 - 400 N). Specimens were tested native, with cartilage damage caused by drying out and relubricated. Dissipated energy (DE) as a measure of friction was recorded and compared., Results: Investigating the effect of axial load, we found significant differences in DE between all axial load steps (p < .001), however, only for the defect cartilage. Furthermore, we could document an increase in DE from native (Mean: 15.0 mJ/cycle, SD: 8.98) to cartilage damage (M: 74.4 mJ/cycle, SD: 79.02) and a decrease after relubrication to 23.6 mJ/cycle (SD: 18.47). Finally, we compared the DE values for NaCl, FCS and HA. The highest values were detected for NaCl (M Norm  = 16.4 mJ/cycle, SD: 19.14). HA achieved the lowest value (M Norm  = 4.3 mJ/cycle, SD: 4.31), although the gap to FCS (M Norm  = 5.1 mJ/cycle, SD: 7.07) was small., Conclusions: We were able to elucidate three effects in joints with cartilage damage. First, the friction in damaged joints increases significantly compared to native joints. Second, especially in damaged joints, the friction increases significantly more with increased axial load compared to native or relubricated joints. Third, lubricants can achieve an enormous decrease in friction. Comparing different lubricants, our results indicate the highest decrease in friction for HA., (© 2022. The Author(s).)

The results of compressive fatigue investigations on four high-strength concretes and their corresponding mortars are presented. The influences of coarse aggregates generally, the substitution of basalt coarse aggregate by granite, the addition of silica fume and the variation of the water to cement ( w/c ) ratio are investigated systematically. The numbers of cycles to failure, the developments of strain, stiffness, dissipated energy and acoustic emission hits are focused on in the analyses. The results clearly show that coarse aggregates can influence the fatigue behaviour of concretes in a negative way at higher stress levels and in a positive way at lower stress levels compared to mortars. The granite coarse aggregate decreases the adverse effect at higher stress levels due to its lower modulus of elasticity compared to that of the basalt aggregate. Silica fume improves the fatigue behaviour of concrete and mortar strongly. The increase of the w/c ratio and, thus, the increase in porosity reduces the fatigue resistance of concrete and mortar significantly, due to the weakening of the mortar matrix and of the interfacial transition zone. The results demonstrate the interaction of the coarse aggregates and the mortar matrix with their specific properties, which leads to a certain fatigue behaviour. The acoustic emission gives additional valuable strain-independent information of the damage processes occurring, possibly also on micro- and nanoscales., Competing Interests: Conflict of interestThe authors have no conflicts of interest to declare that are relevant to the content of this article., (© The Author(s) 2022.)

Accurate characterisation and appropriate binder selection are essential to increase the load-induced cracking resistance of asphalt mixtures at an intermediate temperature. Hence, the primary goal of this study was to correlate the cracking resistance exerted by the binder with the cracking performance of asphalt mixtures. The laboratory-based experimental plan covered various types of laboratory tests specified by various agencies and road authorities to study the correlation of a neat bitumen and five polymer-modified binders with their corresponding asphalt mixtures. The fatigue life of the binders was assessed through a Linear Amplitude Sweep (LAS) test and statistically correlated with various load-induced cracking parameters from the indirect tensile test, semi-circular bending (SCB) test, and four points bending beam test (FPBB) of asphalt mixtures at 25 °C. Binders and mixes were further grouped depending on their polymeric family (i.e., modified with a particular type of polymer) to validate their statistical correlation. The indicator that mostly correlated the binder properties with the asphalt mixture properties is the secant modulus from the SCB test. Fatigue parameters obtained through LAS better explain the asphalt fatigue performance obtained through FPBB; specifically, asphalt tests at high strain levels (e.g., 400 micro strain) better correlate to the LAS fatigue parameter (Nf).

With the increased use of reclaimed asphalt (RA), the ability of bituminous materials to resist fatigue cracking may face a decline mainly due to the aged reclaimed asphalt binder (RAB), especially when RA is used at higher rates and not sufficiently treated. In this study, the bulk scale (asphalt) and its subscale (mortar) were employed to evaluate the effect on fatigue resistance when a RAB is added, by considering three replacement rates: 0%, 40%, and 70% RAB. The fatigue testing of asphalt mixtures was carried out using a four-point bending (4PB) setup, while the mortars were tested using a new column-like geometry utilising a dynamic shear rheometer (DSR). The fatigue properties were further analysed using dissipated energy concepts. The aim of this study was, first, to assess whether the inclusion of a RAB can provide at least similar fatigue properties compared to an all-virgin mix, and second, to evaluate whether the proposed treatment is beneficial for the mixtures with a RAB. The asphalt tests revealed that the inclusion of a 40% RAB led to increased fatigue resistance, whereas the mortar tests showed that the inclusion of RAB has an inverse effect on fatigue life.

Focal cartilage defects can be treated by osteochondral autologous transplantation (OAT). High congruence of the graft with the surrounding cartilage structure is essential for a good clinical outcome, but can not always be achieved. We recently established a method to measure dissipated energy (DE) as a friction parameter in knee joints. We now investigated how autograft harvesting and implant positioning affect the DE during knee motion. Six sheep knee joints were cyclically motioned under 400 N axial load. During the cyclic motion, the flexion angle and the respective torque were recorded and the DE was calculated. Several experimental conditions were tested: first, the DE was measured after approach had been performed ("native"). Subsequently, a cylinder was removed from the medial femur condyles and a donor cylinder was inserted from an unloaded site in four different transplant positions: even, 1 mm deeper, 1 mm higher, and flush without cartilage (defect). No significant changes in friction were observed between the native knee and an even or deep OAT positioning. We, however, found a small but significant increase in DE between the "native" and "1 mm high" formations (ΔDE compared with native = 14 mJ/cycle; P = .004 after data normalization) and a large increase in defect situation (ΔDE compared with native = 119 mJ/cycle; P = .001). Considering the long-term therapeutic aim that is pursued when performing OAT, elevated graft positioning should clearly be avoided. From a biomechanical point of view, donor site morbidity after cylinder harvest can be neglected., (© 2020 University of Tuebingen. Journal of Orthopaedic Research® published by Wiley Periodicals, Inc. on behalf of Orthopaedic Research Society.)

Background: Lateral tibial split fractures (LTSF) usually require surgical therapy with screw or plate osteosynthesis. Excellent anatomical reduction of the fracture is thereby essential to avoid post-traumatic osteoarthritis. In clinical practice, a gap and step of 2 mm have been propagated as maximum tolerable limit. To date, biomechanical studies regarding tibial fractures have been limited to pressure measurement, but the relationship between dissipated energy (DE) as a friction parameter and reduction accuracy in LTSF has not been investigated. In past experiments, we developed a new method to measure DE in ovine knee joints. To determine weather non-anatomical fracture reduction with lateral gap or vertical step condition leads to relevant changes in DE in the human knee joint, we tested the applicability of the new method on human LTSFs and investigated whether the current limit of 2 mm gap and step is durable from a biomechanical point of view., Methods: Seven right human, native knee joint specimens were cyclically moved under 400 N axial load using a robotic system. During the cyclic motion, the flexion angle and the respective torque were recorded and the DE was calculated. First, DE was measured after an anterolateral approach had been performed (condition "native"). Then a LTSF was set with a chisel, reduced anatomically, fixed with two set screws and DE was measured ("even"). DE of further reductions was then measured with gaps of 1 mm and 2 mm, and a 2 mm step down or a 2 mm step up was measured., Results: We successfully established a measurement protocol for DE in human knee joints with LTSF. While gaps led to small though statistically significant increase (1 mm gap:ΔDE compared with native = 0.030 J/cycle, (+ 21%), p = 0.02; 2 mm gap:ΔDE = 0.032 J/cycle, (+ 22%), p = 0.009), this increase almost doubled when reducing in a step-down condition (ΔDE = 0.058 J/cycle, (+ 56%), p = 0.042) and even tripled in the step-up condition (ΔDE = 0.097 J/cycle, (+ 94%), p = 0.004)., Conclusions: Based on our biomechanical findings, we suggest avoiding step conditions in the daily work in the operating theatre. Gap conditions can be handled a bit more generously.

We examine different approaches to model viscoelasticity within atomic force microscopy (AFM) simulation. Our study ranges from very simple linear spring-dashpot models to more sophisticated nonlinear systems that are able to reproduce fundamental properties of viscoelastic surfaces, including creep, stress relaxation and the presence of multiple relaxation times. Some of the models examined have been previously used in AFM simulation, but their applicability to different situations has not yet been examined in detail. The behavior of each model is analyzed here in terms of force-distance curves, dissipated energy and any inherent unphysical artifacts. We focus in this paper on single-eigenmode tip-sample impacts, but the models and results can also be useful in the context of multifrequency AFM, in which the tip trajectories are very complex and there is a wider range of sample deformation frequencies (descriptions of tip-sample model behaviors in the context of multifrequency AFM require detailed studies and are beyond the scope of this work).

Osteochondral autologous transplantation is frequently used to repair small cartilage defects. Incongruence between the osteochondral graft surface and the adjacent cartilage leads to changed friction and contact pressure. The present study wanted to analyze the differences between intact and surgically treated cartilage surface in respect to contact pressure and frictional characteristic (dissipated energy). Six ovine carpometacarpal joints were used in the present study. Dissipated energy during instrumentally controlled joint movement as well as static contact pressure were measured in different cartilage states (intact, defect, deep-, flush-, high-implanted osteochondral graft and cartilage failure simulation on a high-implanted graft). The best contact area restoration was observed after the flush implantation. However, the dissipated energy measurements did not reveal an advantage of the flush implantation compared to the defect and deep-implanted graft states. The high-implanted graft was associated with a significant increase of the mean contact pressure and decrease of the contact area but the dissipated energy was on the level of intact cartilage in contrast to other treatments where the dissipated energy was significantly higher as in the intact state. However the cartilage failure simulation on the high-implanted graft showed the highest increase of the dissipated energy., (Copyright © 2014 IPEM. Published by Elsevier Ltd. All rights reserved.)