Search

Interfacial dilational rheology is one of the important means to explore the interfacial properties of adsorption films. In this paper, the interfacial rheological properties of the mixed system of sulfobetaine ASB with a linear alkyl group and two anionic surfactants, petroleum sulfonate (PS) and alkyl polyoxyethylene carboxylate (AEC), were investigated by interfacial dilational rheology. The effect of the introduction of polymer hydrophobically modified polyacrylamide (HMPAM) on the interfacial properties of the mixed system was analyzed. In this experiment, the surfactant solution was used as the external phase and n-decane was used as the internal phase. A periodic sinusoidal disturbance of 0.1 Hz was applied to the n-decane droplets, and the changes of parameters such as droplet interfacial tension and interfacial area were monitored in real time with the help of a computer. The results show that the betaine ASB molecule responds to the dilation and compression of the interface through the change of ion head orientation, while the feedback behavior of petroleum sulfonate PS and AEC molecules embedded with oxygen vinyl groups in the molecule is diffusion and exchange between the interface and the bulk phase. Therefore, the interface film formed by ASB alone is higher, and the film formed by PS and AEC molecules alone is relatively lower. After adding two kinds of anionic surfactants to the betaine system, the ionic head of PS or AEC molecules will be attached to the positive center of the hydrophilic group of ASB molecules by electrostatic attraction and no longer adsorb and desorb with the interface deformation. The interfacial rheological properties of the compound system are still dominated by betaine, with higher dilational modulus and lower phase angle. When a small amount of HMPAM is added, or the content of hydrophobic monomer AMPS in the bulk phase is low, the intermolecular interaction at the interface is enhanced, the slow relaxation process is intensified, and the interfacial film strength is increased. As the content of AMPS further increases, hydrophobic blocks and surfactant molecules will form interfacial aggregates similar to mixed micelles at the oil-water interface, which will regulate the properties of the film by affecting the adsorption of surfactants at the interface. As long as the interfacial tension is the same, the properties of the interfacial film are the same. Based on the colloid interface science and the background of enhanced oil recovery, this study provides a reference for the field application of chemical flooding formulations.

CO 2 miscible flooding in low permeability reservoirs is conducive to significantly improving oil recovery. At present, the microscopic displacement simulation of CO 2 miscible flooding is mainly reflected in the simulation of the seepage process, but the pressure control of the seepage process is lacking, and the simulation of the characterization of CO 2 concentration diffusion is less studied. In view of the above problems, a numerical model of CO 2 miscible flooding is established, and the microscopic seepage characteristics of interphase mass transfer in CO 2 miscible flooding are analyzed by multiphysics field coupling simulations at the two-dimensional pore scale. The injection velocity, contact angle, diffusion coefficient, and initial injection concentration are selected to analyze their effects on the microscopic seepage characteristics of CO 2 miscible flooding and the concentration distribution in the process of CO 2 diffusion. The research shows that after injection into the model, CO 2 preferentially diffuses into the large pore space and forms a miscible area with crude oil through interphase mass transfer, and the miscible area expands continuously and is pushed to the outlet by the high CO 2 concentration area. The increase in injection velocity will accelerate the seepage process of CO 2 miscible displacement, which will increase the sweep area at the same time. The increase in contact angle increases the seepage resistance of CO 2 and weakens the interphase mass transfer with crude oil, resulting in a gradual decrease in the final recovery efficiency. When the diffusion coefficient increases, the CO 2 concentration in the small pores and the parts that are difficult to reach at the model edge will gradually increase. The larger the initial injection concentration is, the larger the CO 2 concentration in the large pore and miscible areas in the sweep region at the same time. This study has guiding significance for the field to further understand the microscopic seepage characteristics of CO 2 miscible flooding under the effect of interphase mass transfer., Competing Interests: The authors declare no competing financial interest., (© 2023 The Authors. Published by American Chemical Society.)