Search

Significant interest has emerged for the application of Pd-In 2 O 3 catalysts as high-performance catalysts for CO 2 hydrogenation to CH 3 OH. However, precise active site control in these catalysts and understanding their reaction mechanisms remain major challenges. In this investigation, a series of Pd-InO x catalysts were synthesized, revealing three distinct types of active sites: In-O, Pd-O(H)-In, and Pd 2 In 3 . Lower Pd loadings exhibited Pd-O(H)-In sites, while higher loadings resulted in Pd 2 In 3 intermetallic compounds. These variations impacted catalytic performance, with Pd-O(H)-In catalysts showing heightened activity at lower temperatures due to the enhanced CO 2 adsorption and H 2 activation, and Pd 2 In 3 catalysts performing better at elevated temperatures due to the further enhanced H 2 activation. In situ DRIFTS studies revealed an alteration in key intermediates from *HCOO over In-O bonds to *COOH over Pd-O(H)-In and Pd 2 In 3 sites, leading to a shift in the main reaction pathway transition and product distribution. Our findings underscore the importance of active site engineering for optimizing catalytic performance and offer valuable insights for the rational design of efficient CO 2 conversion catalysts.

Defect manipulation in metal oxide is of great importance in boosting catalytic performance for propane oxidation. Herein, a selective atom removal strategy was developed to construct a defective manganese oxide catalyst, which involved the partial etching of a Mg dopant in MnO x . The resulting MgMnO x -H catalysts exhibited superior low-temperature catalytic activity (T 50 = 185 °C, T 90 = 226 °C) with a propane conversion rate of 0.29 μmol·g cat. -1 ·h -1 for the propane oxidation reaction, which is 4.8 times that of pristine MnO x . Meanwhile, a robust hydrothermal stability was guaranteed at 250 °C for 30 h of reaction time. The comprehensive experimental characterizations revealed that the catalytic performance improvement was closely related to the defective structures including the abundant (metal and oxygen) vacancies, distorted crystals, valence imbalance, etc., which prominently weakened the Mn-O bond and stimulated the mobility of surface lattice oxygen, leading to the elevation in the intrinsic oxidation activity. This work exemplifies the significance of defect engineering for the promotion of the oxidation ability of metal oxide, which will be valuable for the further development of efficient non-noble metal catalysts for propane oxidation.

Conventional methods faced challenges in pretreating natural cellulose fibres due to their high energy consumption and large wastewater drainage. This research devised an efficient solid-state pretreatment method for pretreating hemp fibres using ethanolamine (ETA) assisted by microwave (MW) heating. This method produced a notable removal rate of lignin (85.4 %) with the highest cellulose content (83.0 %) at a high solid content (30 %) and low temperature (70 °C). Both FT-IR and XRD analyses indicated that the pretreatment did not alter the structure of cellulose within the hemp fibres but increased crystallinity as the CrI increased from 84 % in raw hemp fibre to 89 % in pretreated fibre. As a result, it produced hemp fibres with impressive fineness (4.6 dtex) and breaking strength (3.81 cN/dtex), meeting the requirement of textile fibre. In addition, an improvement in glucose concentration (15.6 %) was observed in enzymatic hydrolysis of the MW pretreated hemp fibres compared to the fibres pretreated without MW. Furthermore, the FT-IR and NMR data confirmed that the amination of lignin occurred even at low temperature, which contributed to the high lignin removal rate. Thus, this study presents a potentially effective energy-saving, and environmentally sustainable solid-state method for pretreating hemp fibres., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024. Published by Elsevier Ltd.)

Transition metal sulfides (TMS) have gained significant attention as potential anode materials for sodium ion batteries (SIBs) due to their high theoretical capacity and abundance in nature. Nevertheless, their practical use has been impeded by challenges such as large volume changes, unstable solid electrolyte interphase (SEI), and low initial coulombic efficiency (ICE). To address these issues and achieve both long-term cycling stability and high ICE simultaneously, we present a novel approach involving surface engineering, termed as the "dual-polar confinement" strategy, combined with interface engineering to enhance the electrochemical performance of TMS. In this approach, CoS crystals are meticulously coated with polar TiO 2 and embedded within a polar S-doped carbon matrix, forming a composite electrode denoted as CoS/TiO 2 -SC. Significantly, an ether-based electrolyte with chemical stability and optimized solvation properties synergistically interacts with the Co-S-C bonds to create a stable, ultra-thin SEI. This concerted effect results in a notably high ICE, reaching approximately 96%. Advanced characterization and theoretical simulations confirm that the uniform surface modification effectively facilitates sodium ion transport kinetics, restrains electrode pulverization, and concurrently enhances interaction with the ether-based electrolyte to establish a robust SEI. Consequently, the CoS/TiO 2 -SC electrode exhibits high reversible capacity, superior rate capability, and outstanding cycling stability., Competing Interests: There are no conflicts to declare., (This journal is © The Royal Society of Chemistry.)

The traditional textile degumming process produces abundant wastewater, which contains a lot of monosaccharides and oligosaccharides. It is of great economic and environmental significance to utilize these carbohydrates in high value. In this study, high performance liquid chromatography (HPLC) was used to analyze the carbohydrate components in kenaf degumming wastewater, and then the production of C-dots using the wastewater was explored. The results showed that the types and content in the degumming wastewater were monosaccharides (glucose, xylose and arabinose) and oligosaccharides (dextran, xylan and araban). The carbohydrate (mainly glucan and xylan) content in wastewater accounted for 91.16 % of the total carbohydrates weight loss in kenaf degumming process. By using hydrolysis and hydrothermal reaction on kenaf degumming wastewater, blue-green carbon dots (C-dots) with good performance were prepared and successfully applied to anti-counterfeiting printing. In particular, the as-prepared C-dots prepared from kenaf degumming wastewater with urea added (WUC-dots) showed an excitation-dependent photoluminescence (PL) spectrum and quantum yield (QY) of 2.4 % in aqueous solution. The fluorescent code exhibited a clear outline, excitation-tunable color and good stability, showing a great potential for anti-counterfeiting system., Competing Interests: Declaration of competing interest There are no conflicts to declare., (Copyright © 2024 Elsevier B.V. All rights reserved.)

In order to fabricate a novel antioxidant nanofiber facial mask, a metal cone modified in-situ electrospinning with precise deposition was employed by utilizing Enteromorpha prolifera polysaccharides (EPPs). The metal cone could control the deposition area to achieve precise fabrication of facial mask on skin. The EPPs exhibited remarkable antioxidant ability, as evidenced by the half-maximal inhibitory concentrations (IC 50 ) of 1.44 mg/mL and 0.74 mg/mL against DPPH and HO• free radicals, respectively. The antioxidant ability of the facial mask was improved by elevating the electrospinning voltage from 15 kV to 19 kV, due to the improved release capacity of EPPs by 7.09 %. Moreover, the facial mask demonstrated robust skin adhesion and moisture-retaining properties compared with commercial facial mask, which was benefited by the in-situ electrospinning technology. Furthermore, cytotoxicity assay, animal skin irritation test, and ocular irritation test collectively affirmed the safety of the facial mask. Thus, this research introduces a novel in situ electrospinning with precise deposition method and a natural antioxidant additive for preparing facial mask., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 Elsevier B.V. All rights reserved.)

The catalytic conversion of cellulose to lactic acid (LA) has garnered significant attention in recent years due to the potential of cellulose as a renewable and sustainable biomass feedstock. Here, a series of Au/W-ZnO catalysts were synthesized and employed to transform cellulose into LA. Through the optimization of reaction parameters and catalyst compositions, we achieved complete cellulose conversion with a selectivity of 54.6% toward LA over Au/W-ZnO at 245 °C for 4 h. This catalyst system also proved effective at converting cotton and kenaf fibers. Structural and chemical characterizations revealed that the synergistic effect of W, ZnO, and Au facilitated mesoporous architecture generation and the establishment of an adequate acidic environment. The catalytic process proceeded through the hydrolysis of cellulose to glucose, isomerization to fructose, and its subsequent conversion to LA, with glucose isomerization identified as the rate-limiting step. These findings provide valuable insights for developing high-performance catalytic systems to convert cellulose.

The utilization of Cu-based catalysts in CO 2 conversion into valuable chemicals is of significant interest due to their potential in mitigating greenhouse gas emissions. However, the controllable design of Cu-based catalysts and the regulation of their mechanism remain challenging. In this study, a series of efficient Cu/L catalysts were prepared for this process, and the intrinsic influencing factors on the reaction routes were systematically revealed. Various techniques revealed that Cu particles in L-supported catalysts exhibited higher dispersion and formed Cu-O(OH)-K interfacial sites. However, with increasing Cu loading, the dispersion of Cu particles and the percentage of Cu-O(OH)-K interfaces decreased. Kinetic investigations revealed that the adsorption configuration and electronic structure of Cu species codetermined the reaction pathways and resulting selectivity. Cu/L catalysts possessing Cu-O(OH)-K interfaces and small particles demonstrated the preferential formation of formate species, promoting methanol formation. However, larger Cu particles generated carboxylate intermediates, resulting in higher CO selectivity..

Herein, a series of Ru/ZTCs samples were prepared using LaY zeolite-templated carbon as a support. Characterizations showed that the unique structure of the ZTCs and the chemical state of Ru facilitated superior HER performance compared to other carbon-supported samples. This work offers a new strategy for designing excellent electrocatalysts.

Interface engineering in electrode materials is an attractive strategy for enhancing charge storage, enabling fast kinetics, and improving cycling stability for energy storage systems. Nevertheless, the performance improvement is usually ambiguously ascribed to the "synergetic effect", the fundamental understanding toward the effect of the interface at molecular level in composite materials remains elusive. In this work, a well-defined nanoscale MoS 2 /TiO 2 interface is rationally designed by immobilizing TiO 2 nanocrystals on MoS 2 nanosheets. The role of heterostructure interface between TiO 2 and MoS 2 by operando synchrotron X-ray diffraction (sXRD), solid-state nuclear magnetic resonance, and density functional theory calculations is investigated. It is found that the existence of a hetero-interfacial electric field can promote charge transfer kinetics. Based on operando sXRD, it is revealed that the heterostructure follows a solid-solution reaction mechanism with small volume changes during cycling. As such, the electrode demonstrates ultrafast Na + ions storage of 300 mAh g -1 at 10 A g -1 and excellent reversible capacity of 540 mAh g -1 at 0.2 A g -1 . This work provides significant insights into understanding of heterostructure interface at molecular level, which suggests new strategies for creating unconventional nanocomposite electrode materials for energy storage systems., (© 2022 The Authors. Advanced Science published by Wiley-VCH GmbH.)

Environmentally friendly face masks with high filtration efficiency are in urgent need to fight against the COVID-19 pandemic, as well as other airborne viruses, bacteria and particulate matters. In this study, coaxial electrospinning was employed to fabricate a lithium chloride enhanced cellulose acetate/thermoplastic polyurethanes (CA/TPU-LiCl) face mask nanofiber filtration membrane, which was biodegradable and reusable. The analysis results show that the CA/TPU-LiCl membrane had an excellent filtration performance: when the filtration efficiency reached 99.8%, the pressure drop was only 52 Pa. The membrane also had an outstanding reusability. The filtration performance maintained at 98.2% after 10 test cycles, and an alcohol immersion disinfection treatment showed no effect on its filtration performance. In summary, the CA/TPU-LiCl nanofiber membrane made in this work is a promising biodegradable and reusable filtration material with a wide range of potential applications, including high-performance face mask.

Chemically deuterated cellulose fiber was expected to provide novel applications due to its spectral, biological, and kinetic isotope effect. In this research, the performance of the chemically deuterated cotton fibers, including their mechanical property, enzymatic degradation performance, effect on bacterial treatment, and fast identification (near-infrared modeling) was investigated. The breaking tenacity of the deuterated cotton fibers was slightly lower, which might be attributed to the structural damage during the chemical deuteration. The glucose yield by enzymatic hydrolysis was less than that of the protonic cotton fibers, implying the deuterated fibers are less sensitive to enzymatic degradation. Furthermore, the deuterated fibers could promote the growth of bacteria such as Escherichia. coli , which was associated with the released low-level deuterium content. At last, the near-infrared technique combined with partial least squares regression successfully achieved a fast identification of the protiated and deuterated cotton fibers, which significantly promoted the potential application of deuterated cellulose as anticounterfeiting materials (e.g., special paper)., Competing Interests: The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest. The handling editor declared a past collaboration with the author AR., (Copyright © 2021 Song, Liu, Ben, Zhang, Han, Ragauskas and Jiang.)

Bio-oil is a valuable liquid product obtained from pyrolysis of biomass and it contains tens of hundreds of compounds, which brings about difficulties for characterization with various analytical methods. 13 C NMR has advantages over other detection methods as it can characterize the entire composition of bio-oil and distinguish different types of carbon. But various shortcomings limit the application of 13 C NMR. This study was carried out to develop a quantitative 13 C NMR method to determine different functional groups in pyrolysis bio-oils with short NMR time and good accuracy, and propose a simulation of C, H, and O content for pyrolysis oils based on 13 C NMR analysis. In order to solve long-term NMR problems, relax reagent has been added and the results show that it is an effective way to shorten the NMR time. Moreover, the aging problem is not obvious in the short-term NMR test, so the effect of aging on the test results can be neglected. Three types of substances with different oxygen content have been employed to verify the feasibility of the C, H, and O calculation methods and the result errors of all elements are small, which shows it is reliable for the simulation data of C, H and O content., Competing Interests: There are no conflicts to declare., (This journal is © The Royal Society of Chemistry.)

The pyrolysis behavior of corn stover and polypropylene during co-pyrolysis was studied using a tube furnace reactor. The effects of mixing ratio of corn stover and polypropylene, pyrolysis temperature, addition amount of catalyst (HZSM-5) and reaction atmosphere (N 2 and CO 2 ) on the properties of pyrolysis products were studied. The results showed that co-pyrolysis of corn stover and polypropylene can increase the yield of pyrolysis oil. When corn stover:polypropylene = 1:3, the yield of pyrolysis oil was as high as 52.1%, which was 4.5% higher than the theoretical value. With the increase of pyrolysis temperature, the yield of pyrolysis oil increased first and then decreased, and reached the optimal yield at 550 °C. The addition of catalyst (HZSM-5) reduced the proportion of oxygenates and promoted the generation of aromatic hydrocarbons. CO 2 has a certain oxidation effect on the components of pyrolysis oil, which promoted the increase of oxygen-containing aromatics and the reduction of deoxy-aromatic hydrocarbons. This study identified the theoretical basis for the comprehensive utilization of plastic and biomass energy.

The pyrolysis of poly (ethylene terephthalate) (PET) in the presence of ZSM-5 zeolite and NiCl 2 as a catalyst was studied at different temperatures under N 2 atmosphere. Quantitative 13 C nuclear magnetic resonance (NMR) and Fourier transform infrared spectroscopy (FT-IR) were applied to characterize the waxy and solid residue. The carboxyl and aliphatic hydroxyl groups in the waxy residue have been greatly depleted after the use of zeolite during pyrolysis on the basis of the results of 13 C NMR and FT-IR analysis. The proportion of aromatic hydroxyl groups increased by 21.82% when the mass ratio of zeolite to PET was set to 2.0/1.0. The results indicate that ZSM-5 is able to facilitate the decomposition of carboxyl, aliphatic groups, and ether bonds in the primary products produced from the pyrolysis of PET. In addition, the deoxygenation effects on the waxy products have been significantly enhanced with the addition of zeolite based on the results of NMR.

In this paper, the crystalline modification of isotactic polypropylene (PP) with a rare earth β nucleating agent (WBG) with different ultrasound conditions was investigated by scanning electron microscopy (SEM), wide-angle X-ray diffraction (XRD), and differential scanning calorimetry (DSC). The relationship between the ultrasound conditions and the crystalline structure, as well as the mechanism for the behavior, were revealed. SEM showed that the dispersion of the nucleating agent in the PP matrix was better at shorter ultrasound distances. In addition, the higher the water cooling temperature, the better the nucleating agent was dispersed in the PP matrix. The results of XRD and DSC showed that the crystallinity and the relative content of the β -crystal were increased with nearer ultrasound distance, as well as increased in higher water cooling temperatures. In particular, under the same conditions, the crystallinity and the relative content of the β -crystal after ultrasonic treatment were much higher than those without ultrasound., Competing Interests: The authors declare no conflict of interest.

The analysis of chemical structural characteristics of biorefinery product streams (such as lignin and tannin) has advanced substantially over the past decade, with traditional wet-chemical techniques being replaced or supplemented by NMR methodologies. Quantitative 31 P NMR spectroscopy is a promising technique for the analysis of hydroxyl groups because of its unique characterization capability and broad potential applicability across the biorefinery research community. This protocol describes procedures for (i) the preparation/solubilization of lignin and tannin, (ii) the phosphitylation of their hydroxyl groups, (iii) NMR acquisition details, and (iv) the ensuing data analyses and means to precisely calculate the content of the different types of hydroxyl groups. Compared with traditional wet-chemical techniques, the technique of quantitative 31 P NMR spectroscopy offers unique advantages in measuring hydroxyl groups in a single spectrum with high signal resolution. The method provides complete quantitative information about the hydroxyl groups with small amounts of sample (~30 mg) within a relatively short experimental time (~30-120 min).

One of the major obstacles to the widespread use of pyrolysis oil is its high oxygen content, with oxygen atoms being mainly present in the hydroxyl and the carboxyl groups. Therefore, quantitative and accurate characterization of oxygen-containing functional groups is of great significance. This study employed 31 P NMR to conduct in-depth studies on several model compounds including four kinds of alcohols and carboxylic acids. The model compounds have been investigated for stability in 31 P NMR solution for both short storage (4 hours) and long storage (14 days), namely by in and ex situ monitoring. The experimental phenomena indicates that carboxylic hydroxyl has poor stability compared to alcohols hydroxyl group, which is reflected in the amount of alcohol compounds remaining over 90% after long-term storage. Among the carboxylic acids used in the study, aromatic acids are relatively stable. Interestingly, oxalic acid is extremely unstable and completely decomposed in the first hour, while formic acid had only a small amount left after one day of storage. Therefore, the optimum time for the preparation, storage and upgrading of the pyrolysis oil can be determined by analysis of the stability of the oxygen-containing functional groups in 31 P NMR solution to ensure accuracy. Moreover, according to the results of the 31 P NMR and other characterization methods, it can been seen that water was formed during the decomposition of all the model compounds. This is a report on the quantitative characterization of different oxygen-containing functional groups representing pyrolysis oil and the first study on the similarities and differences of the decomposition of carboxylic acids and alcohols in 31 P NMR solution. The results of this in-depth investigation can provide important assistance in research that will further upgrade and apply pyrolysis oil., Competing Interests: The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest., (This journal is © The Royal Society of Chemistry.)

Pyrolysis of raw pine bark, pine, and Douglas-Fir bark was examined. The pyrolysis oil yields of raw pine bark, pine, and Douglas-Fir bark at 500 °C were 29.18%, 26.67%, and 26.65%, respectively. Both energy densification ratios (1.32-1.56) and energy yields (48.40-54.31%) of char are higher than pyrolysis oils (energy densification ratios: 1.13-1.19, energy yields: 30.16-34.42%). The pyrolysis oils have higher heating values (~25 MJ/kg) than bio-oils (~20 MJ/kg) from wood and agricultural residues, and the higher heating values of char (~31 MJ/kg) are comparable to that of many commercial coals. The elemental analysis indicated that the lower O/C value and higher H/C value represent a more valuable source of energy for pyrolysis oils than biomass. The nuclear magnetic resonance results demonstrated that the most abundant hydroxyl groups of pyrolysis oil are aliphatic OH groups, catechol, guaiacol, and p -hydroxy-phenyl OH groups. The aliphatic OH groups are mainly derived from the cleavage of cellulose glycosidic bonds, while the catechol, guaiacol, and p -hydroxy-phenyl OH groups are mostly attributed to the cleavage of the lignin β-O-4 bond. Significant amount of aromatic carbon (~40%) in pyrolysis oils is obtained from tannin and lignin components and the aromatic C-O bonds may be formed by a radical reaction between the aromatic and aliphatic hydroxyl groups. In this study, a comprehensive analytical method was developed to fully understand and evaluate the pyrolysis products produced from softwood barks, which could offer valuable information on the pyrolysis mechanism of biomass and promote better utilization of pyrolysis products.

Abundant studies have been completed about factors on the pyrolysis of coal and biomass. However, few articles laid emphasis on using CO 2 as a carrier gas to explore the compositional changes of pyrolysis products in coal and biomass pyrolysis for industrial application and commercial value. The experiments on coal and biomass pyrolysis in N 2 and CO 2 using a horizontal tube furnace were conducted at 500 °C. The impact of introducing CO 2 on the pyrolysis process of bituminous coal and Platanus sawdust was investigated. The nuclear magnetic resonance (NMR) spectra of tar and the characterizations of char including Brunner-Emmet-Teller (BET) measurements, scanning electron microscope (SEM), Fourier transform infrared (FT-IR) spectroscopy, and element analysis were studied. The findings in light of the experimental results show that introducing CO 2 enhances the coal and biomass pyrolysis in a solid product by promoting the fracture of hydroxyl groups. It also promotes tar decomposition and the release of volatiles, which contribute to the occurrence of char with high porosity, pore volume, and specific surface. Furthermore, higher specific surface enhances the adsorption performance of char as active carbon. Simultaneously, CO 2 promotes the increase of oxygen-containing aromatics especially the methoxy-containing aromatics, and the decrease of deoxygenated aromatic hydrocarbons in pyrolysis oils. In addition, the introduction of CO 2 changes the amount of aliphatic compounds in various ways for the pyrolysis of coal and biomass. From a perspective of business, the changes in the composition of pyrolysis oil brought by CO 2 may create new value for fuel utilization and industrial products.

Artemisia vulgaris is an economic plant that is spreading widely in central China. Its unused bast generates a large amount of biomass waste annually. Utilizing the fibers in Artemisia vulgaris bast may provide a new solution to this problem. This research attempts to strengthen the understanding of Artemisia vulgaris by analyzing its fiber compositions and preparing micro- and nano-cellulose fibers, which can be used as raw materials for composites. In this work, Artemisia vulgaris bast powder (AP) and microcellulose and nanocellulose fibers (AMFs and ANFs) were produced and characterized by optical microscopy, transmission electron microscopy (TEM), X-ray diffraction (XRD), thermogravimetric analysis (TG), and bacteriostatic test. The results indicated that cellulose, hemicellulose, and lignin were the main components in the Artemisia vulgaris bast. The cellulose content reached 40.9%. The Artemisia vulgaris single fibers were microcellulose fibers with an average length of 850.6 μm and a diameter of 14.4 μm. Moreover, the AMF had considerable antibacterial ability with an antibacterial ratio of 36.6%. The ANF showed a length range of 250-300 nm and a diameter of 10-20 nm, and it had a higher crystallinity (76%) and a lower thermal stability (initial degradation temperature of 183 °C) compared with raw ANF (233 °C). This study provides fundamental information on Artemisia vulgaris bast cellulose for its subsequent utilization., Competing Interests: The authors declare no conflict of interest.

Background: Biological routes for utilizing both carbohydrates and lignin are important to reach the ultimate goal of bioconversion of full carbon in biomass into biofuels and biochemicals. Recent biotechnology advances have shown promises toward facilitating biological transformation of lignin into lipids. Natural and engineered  Rhodococcus strains (e.g.,  R. opacus PD630 , R. jostii  RHA1, and R. jostii  RHA1 VanA - ) have been demonstrated to utilize lignin for lipid production, and co-culture of them can promote lipid production from lignin., Results: In this study, a co-fermentation module of natural and engineered  Rhodococcus strains with significant improved lignin degradation and/or lipid biosynthesis capacities was established, which enabled simultaneous conversion of glucose, lignin, and its derivatives into lipids. Although  Rhodococci  sp. showed preference to glucose over lignin, nearly half of the lignin was quickly depolymerized to monomers by these strains for cell growth and lipid synthesis after glucose was nearly consumed up. Profiles of metabolites produced by Rhodococcus  strains growing on different carbon sources (e.g., glucose, alkali lignin, and dilute acid flowthrough-pretreated poplar wood slurry) confirmed lignin conversion during co-fermentation, and indicated novel metabolic capacities and unexplored metabolic pathways in these organisms. Proteome profiles suggested that lignin depolymerization by  Rhodococci sp. involved multiple peroxidases with accessory oxidases. Besides the β-ketoadipate pathway, the phenylacetic acid (PAA) pathway was another potential route for the in vivo ring cleavage activity. In addition, deficiency of reducing power and cellular oxidative stress probably led to lower lipid production using lignin as the sole carbon source than that using glucose., Conclusions: This work demonstrated a potential strategy for efficient bioconversion of both lignin and glucose into lipids by co-culture of multiple natural and engineered Rhodococcus strains. In addition, the involvement of PAA pathway in lignin degradation can help to further improve lignin utilization, and the combinatory proteomics and bioinformatics strategies used in this study can also be applied into other systems to reveal the metabolic and regulatory pathways for balanced cellular metabolism and to select genetic targets for efficient conversion of both lignin and carbohydrates into biofuels., Competing Interests: The authors declare that they have no competing interests.

The pyrolytic behavior of several biomass components including cellulose, hemicellulose, lignin, and tannin, from two sources of waste biomass (i.e., pine bark and pine residues) were examined. Compared to the two aromatic-based components in the biomass, carbohydrates produced much less char but more gas. Surprisingly, tannin produced a significant amount of water-soluble products; further analysis indicated that tannin could produce a large amount of catechols. The first reported NMR chemical shift databases for tannin and hemicellulose pyrolysis oils were created to facilitate the HSQC analysis. Various C⁻H functional groups (>30 different C⁻H bonds) in the pyrolysis oils could be analyzed by employing HSQC-NMR. The results indicated that most of the aromatic C⁻H and aliphatic C⁻H bonds in the pyrolysis oils produced from pine bark and pine residues resulted from the lignin and tannin components. A preliminary study for a quantitative application of HSQC-NMR on the characterization of pyrolysis oil was also done in this study. Nevertheless, the concepts established in this work open up new methods to fully characterize the whole portion of pyrolysis oils produced from various biomass components, which can provide valuable information on the thermochemical mechanisms.

Aqueous phase hydrodeoxygenation of lignin pyrolysis oil and related model compounds were investigated using four noble metals supported on activated carbon. The hydrodeoxygenation of guaiacol has three major reaction pathways and the demethylation reaction, mainly catalyzed by Pd, Pt and Rh, produces catechol as the products. The presence of catechol and guaiacol in the reaction is responsible for the coke formation and the catalysts deactivation. As expected, there was a significant decrease in the specific surface area of Pd, Pt and Rh catalysts during the catalytic reaction because of the coke deposition. In contrast, no catechol was produced from guaiacol when Ru was used so a completely hydrogenation was accomplished. The lignin pyrolysis oil upgrading with Pt and Ru catalysts further validated the reaction mechanism deduced from model compounds. Fully hydrogenated bio-oil was produced with Ru catalyst., (Copyright © 2014 Elsevier Ltd. All rights reserved.)

This study demonstrates the use of isotopic labelling and NMR to study the HDO process. As far as we know, this is the first reported effort to trace the incorporation of hydrogen in the HDO process of lignin pyrolysis oil thereby providing key fundamental insight into its reaction mechanism.

The pyrolysis of softwood (SW) kraft lignin and pine wood in different pyrolysis systems were examined at 400, 500 and 600 °C. NMR including quantitative (13)C and Heteronuclear Single-Quantum Correlation (HSQC)-NMR, and Gel Permeation Chromatography (GPC) were used to characterize various pyrolysis oils. The content of methoxyl groups decreased by 76% for pine wood and 70% for lignin when using fast pyrolysis system. The carbonyl groups also decreased by 76% and nearly completely eliminated in 600 °C pine wood fast pyrolysis oil. Compared to the slow pyrolysis process, fast pyrolysis process was found to improve the cleavage of methoxyl groups, aliphatic CC bonds and carbonyl groups and produce more polyaromatic hydrocarbons (PAH) from lignin and aliphatic CO bonds from carbohydrates. Another remarkable difference between fast and slow pyrolysis oils was the molecular weight of fast pyrolysis oils increased by 85-112% for pine wood and 104-112% for lignin., (Copyright © 2013 Elsevier Ltd. All rights reserved.)

COMING OF AGE: A method for investigating the accelerated aging of biomass pyrolysis oils is reported. The in situ NMR investigation, done by using quantitative ¹H, ¹³C NMR and heteronuclear single-quantum correlation (HSQC)-NMR techniques, reveals the chemical structural changes of pyrolysis oil during the aging process, providing insight into the mechanism of aging process., (Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)