Search

Single-confinement housing can pose welfare risks to domestic horses. This study investigated horses' stress responses when confined to single stalls in different stable designs in a tropical savanna region to address a gap in the literature. In total, 23 horses were assigned to a stable with a central corridor and solid external walls (A) (N = 8), a stable with one side corridor and solid external walls (B) (N = 6), or a stable with a central corridor and no solid external walls (C) (N = 9). Air velocity, relative humidity, air temperature, and noxious gases were measured inside the stables, and the heart rate and HRV of the horses were also determined. The relative humidity was lower in stable C than in stable A ( p < 0.05), while the air temperature was higher in stable C than in stable B ( p < 0.05) during the day. The airflow and ammonia levels were higher in stable C than in stables B and A ( p < 0.01-0.0001). Overall, horses' HRV in stable A was lower than in those in stables B and C ( p < 0.05-0.01). Horses in stable A tended to experience more stress than those in other stables.

The indoor climate to which livestock are exposed is a critical factor influencing their performance and productivity. Elevated air temperature and relative humidity could result in heat stress for laying hens. This situation results in severe adverse effects such as weight loss and mortality. Egg fertility and hatchability are also impacted. Consequently, a study was carried out in a naturally ventilated battery-caged laying hen house to measure climatic variables (air temperature, relative humidity and air velocity). The degree of heat stress was assessed using the temperature-humidity index (THI), and the index of temperature and air velocity (ITV) was also evaluated. According to the results obtained, birds reared within the study building would spend most of their productive life under stressful thermal conditions, which could significantly hamper their performance. The air velocity was below 1.0 ms -1 for most of the internal part of the housing, meaning natural air movement at the location was insufficient to provide a suitable environment for the birds. A high THI was recorded for nearly the entire study period. This high THI could indicate high relative humidity about air temperature. The observed ITV values (ITV > 25) suggest that birds throughout the building could be perpetually uncomfortable. The thermal and velocity profile within the structure could further be assessed numerically using computational fluid dynamics. This would enable engineers to make modifications to improve living conditions within the building., (© 2023. The Author(s) under exclusive licence to International Society of Biometeorology.)

Heat stress is an increasing challenge for production animals, particularly in warmer regions of the world. The aim of this study was to compare the fit of three different relationships when modelling respiration rate (RR) and rectal temperature (RT) in animals exposed to increased load. Data from three published studies on finishing pigs, gestating sows and dairy cows were analysed. RR and RT are characterized by being unaffected by increased heat load as long as it is kept below a certain level, and in warmer conditions they increase with increased heat load. As an expression of heat load either the air temperature or the ET (Effective Temperature) was used. The ET unites the effect of air temperature, air humidity and velocity on the animal perception of increased heat load. The relationship between RR and RT and the temperature or the ET was analysed by multiple change point regression and the cubic relationships were modelled. In general, the models provided better fits for RR compared to RT. Relationships with an unaffected piece followed by a quadratic relationship and the cubic relationships performed nearly equally well. Using ET resulted in better correlations than using temperature alone for gestating sows and dairy cows., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 The Authors. Published by Elsevier Ltd.. All rights reserved.)

Porous materials are able to exchange moisture with the surrounding air. The more hygroscopic they are, the more they contribute to regulate ambient humidity. This ability is characterized by the moisture buffer value (MBV) which is measured under dynamic solicitations according to different protocols. The NORDTEST protocol is the most commonly-used. It gives recommendations regarding the air velocity and the ambient conditions for initial stabilization. The purpose of this article is to measure the MBV according to the NORDTEST protocol and to study the effect of air velocity and of initial conditioning on the MBV results for different materials. Two mineral and two bio-based materials are considered: gypsum (GY), cellular concrete (CC), thermo-hemp (TH) and fine-hemp (FH). Following the NORDTEST classification, GY is a moderate hygric regulator, CC is good, TH and FH are excellent. When the air velocity ranges from 0.1 to 2.6 m/s, the MBV of GY and CC materials remains constant, but the MBV of TH and FH materials is highly affected. The initial conditioning has no effect on the MBV, but has an effect on the water content of the material, whatever the material.

Due to the broiler house's needs for a healthy environment, efficient control system, and appropriate air, several studies were interested in microclimate and air quality characteristics. However, limited studies are conducted to investigate pressure and air velocity within poultry buildings, which are also significant parameters that impact the breeding environment and productivity. As a reason, the objective of this work was to develop a mathematical model exploring the differential pressure and air velocity inside the house. The peculiarity of this research is the use of thermal balance and air properties to propose a model related to birds' weight which can be translated to birds' age and thermal conditions. The proposed approach acquired experimental measurements (e.g., indoor air temperature and humidity, air velocity, and differential pressure) and performed simulations in a mechanically ventilated Mediterranean broiler house over a summer production cycle. The findings revealed that the observed and modelled differential pressure ranged from a negative to a positive pressure (-5 to 39 Pa), with broilers subjected to air velocity varying from 0.09 to 1.641 m s -1 depending on three distinct modes of regulation: nature, power, and tunnel mode. These results confirmed the model's predictive capacity with a relative error of 1.03% of differential pressure and 0.68% of air velocity and a normalised mean square error (NMSE) of -1.06 Pa and 0.19 m s -1 , respectively. Consequently, the methodology applied in this paper may be extended to various species of breeding structures in other seasons, allowing simulation tools and system control improvement., Competing Interests: The authors declare no conflict of interest., (© 2023 The Authors.)

Background: Bacteria are readily nourished in airtight environments with high humidity, such as storage cabinets, clothing closets, and corners, where ventilation is normally low and humidity is high., Objectives: We characterized the role of humidity and ventilation in bacterial growth and genus distribution at different temperatures (26 °C and 34 °C)., Methods: Fresh pork, which was used as the substrate for bacterial culture, was placed in storage cabinets. Bacterial growth and genera distribution on the surface of pork placed in a storage cabinet under different temperatures (26 °C and 34 °C); relative humidity levels (RH: 50%, 70%, 90%); and ventilation conditions (no ventilation and low, medium, and high levels of ventilation) were assessed by rDNA sequencing., Results: Increased ventilation and reduced humidity significantly decreased bacterial growth at 26 °C and 34 °C. The contribution of increased ventilation to the reduction in bacterial growth exceeded that of decreased humidity. Ventilation had the greatest effect on reducing bacterial growth compared to the unventilated conditions at 70% RH. At 34 °C, medium and high levels of ventilation were required to reduce bacterial growth. High temperatures greatly increased bacterial growth, but ventilation could reduce the degree of this increase.

There are several environmental and ambient factors that can affect pig eliminative behaviour. The aim of this survey was to investigate factors related to the physical and ambient environment that have the strongest effects on pig and pen cleanliness and ammonia concentration. Data were collected from 87 pig farms and analysed using mixed (ammonia concentration) or generalized linear (pen and pig cleanliness) model in SAS. The pen was cleaner when pen partitions were open compared to closed (p = 0.010) and increased with increasing amount of litter (p = 0.002), using straw (p = 0.002) as rooting material. Pig cleanliness was higher when pen partitions in the eliminative area were open compared to closed (p = 0.007) and increased with increasing space per pig in the resting area (p < 0.001), with decreasing temperature (p < 0.001), and lowering of air velocity (p = 0.003). Other factors that increased cleanliness was using straw as rooting material (p = 0.028) and increasing amount of litter in the resting area (p = 0.002). Ammonia concentration was reduced with increasing floor space in the eliminative area (p < 0.001) and increasing amount of litter (p = 0.006). Our results pinpoint physical and ambient conditions affecting pen and pig cleanliness and air quality.

Broiler chickens exposed to heat stress adapt to various behavioral changes to regulate their comfortable body temperature, which is critical to ensure their performance and welfare. Hence, assessing various behavioral responses in birds when they are subjected to environmental changes can be essential for assessing their welfare under heat-stressed conditions. This study aimed to evaluate the effect of two air velocity (AV) treatments on heavy broilers' behavioral changes from 43 to 54 days under summer conditions. Two AV treatments (high and low) were applied in six poultry growth chambers with three chambers per treatment and 44 COBB broilers per chamber from 28 to 61 days in the summer of 2019. Three video cameras placed inside each chamber (2.44 m × 2.44 m × 2.44 m in dimension) were used to record the behavior of different undisturbed birds, such as feeding, drinking, resting, standing, walking, panting, etc. The results indicate that the number of chickens feeding, drinking, standing, walking, sitting, wing flapping, and leg stretching changed under AV treatments. High AV increased the number of chickens feeding, standing, and walking. Moreover, a two-way interaction with age and the time of day can affect drinking and panting. This study provides insights into heavy broilers' behavioral changes under heat-stressed conditions and AV treatments, which will help guide management practices to improve birds' performance and welfare under commercial conditions in the future.

This study determined the effects of increasing ambient temperature (T) at different relative humidity (RH) and air velocity (AV) levels on the physiological and productive responses of dairy cows. Twenty Holstein dairy cows were housed inside climate-controlled respiration chambers, in which the climate was programmed to follow a daily pattern of lower night and higher day T with a 9°C difference, excluding effects from sun radiation. Within our 8-d data collection period, T was gradually increased from 7 to 21°C during the night (12 h) and 16 to 30°C during the day (12 h), with an incremental change of 2°C per day for both nighttime and daytime T. During each research period, RH and AV were kept constant at 1 of 5 treatment levels. A diurnal pattern for RH was created, with lower levels during the day and higher levels during the night: low (RH&#95;l: 30-50%), medium (RH&#95;m: 45-70%), and high (RH&#95;h: 60-90%). The effects of AV were studied during the day at 3 levels: no fan (AV&#95;l: 0.1 m/s), fan at medium speed (AV&#95;m: 1.0 m/s), and fan at high speed (AV&#95;h: 1.5 m/s). Effects of short and long exposure time to increasing T were evaluated by collecting data 2 times a day: in the morning [short: 1 h (or less) - exposure time] and afternoon (long: 8 h - exposure time). The animals had free access to feed and water and both were ad libitum. Respiration rate (RR), rectal temperature (RT), skin temperature (ST), dry matter intake, water intake, milk yield, and composition were measured. The inflection point temperatures (IPt) at which a certain variable started to change were determined for the different RH and AV levels and different exposure times. Results showed that IPt under long exposure time for RR (first indicator) varied between 18.9 and 25.5°C but was between 20.1 and 25.9°C for RT (a delayed indicator). The IPt for both RR and RT decreased with higher RH levels, whereas IPt increased with higher AV for RR but gave a minor change for RT. The ST was positively correlated with ambient T and ST was not affected by RH but significantly affected by AV. For RR, all IPt was lower under long exposure time than under short exposure time. The combination of higher RH levels and low AV level negatively affected dry matter intake. Water intake increased under all treatments except RH&#95;l-AV&#95;l. Treatment RH&#95;h-AV&#95;l negatively affected milk protein and fat yield, whereas treatments RH&#95;m-AV&#95;m and RH&#95;m-AV&#95;h reduced milk fat yield. We concluded that RH and AV significantly affected the responses of RR, RT, ST, and productive performance of high-producing Holstein cows. These responses already occurred at moderate ambient T of 19 to 26°C., (The Authors. Published by Elsevier Inc. and Fass Inc. on behalf of the American Dairy Science Association®. This is an open access article under the CC BY license (http://creativecommons.org/licenses/by/4.0/).)

Global warming combined with increased production (i.e. more piglets, more milk and consequently more heat) means that sows are more often challenged by heat stress. The objective was to develop an effective temperature (ET) equation to predict how air temperature, velocity and humidity affect the respiration rate (RR), rectal temperature (RT) and skin temperature (ST) as an expression of heat stress in gestating sows in order to elucidate the relationship between the thermal parameters and the sows' perception of the environment. The experimental room was equipped with a negative pressure ventilation system with diffuse air inlet through the ceiling, electrical heaters, steam generators and dehumidifiers. An air distribution unit was constructed to generate vertical air velocity. A total of 16 gestating sows were exposed to three temperatures (25°C, 29°C and 33°C), two levels of relative humidity (30% and 70%) and three levels of air velocity (0.2 ms -1 , 1 ms -1 and 2.5 ms -1 ). The RR, RT and ST were recorded every 30 min throughout the three 2-h test periods. The estimated effects of humidity and velocity in relation to effect of temperature was nearly independent of whether it was determined from RR or RT, whereas the effect of humidity was much smaller when determined from ST. High coefficients of determination (>0.97) were found for the second order relationship between the estimated ET and RR, RT and ST. An increase in relative humidity from 50 to 70% corresponded to an increase in ET of 0.9°C, while an increase in air velocity from 0.2 to 1.0 ms -1 corresponded to a decrease in ET of 1.2°C. The applied ET equation was useful for expressing the combined effect of temperature, humidity and velocity on animals exposed to heat stress. However, multiplying the effect of velocity by the temperature gradient between the animal and the surrounding air did not improve the estimation., (Copyright © 2021 The Authors. Published by Elsevier Ltd.. All rights reserved.)

Heavy broilers exposed to hot summer conditions experience fluctuations in surface temperatures due to heat stress, which leads to decreased performance. Maintaining a bird's homeostasis depends on several environmental factors (temperature, relative humidity, and air velocity). It is important to understand the responses of birds to environmental factors and the amount of heat loss to the surrounding environment to create thermal comfort for the heavy broilers for improved performances and welfare. This study investigates the variation in surface temperatures of heavy broilers under high and low air velocity treatments. Daytime, age and bird location's effect on the surface temperature variation was also examined. The experiment was carried out in the poultry engineering laboratory of North Carolina State University during summers of 2017, 2018, and 2019 as a part of a comprehensive study on the effectiveness of wind chill application to mitigate heat stress on heavy broilers. This live broiler heat stress experiment was conducted under two dynamic air velocity treatments (high and low) with three chambers per treatment and 44 birds per chamber. Surface temperatures of the birds were recorded periodically through the experimental treatment cycles (flocks, 35-61 d) with infrared thermography in the morning, noon, evening, and nighttime. The overall mean surface temperature of the broilers under two treatments was found to be 35.89 ± 2.37 °C. The variation in surface temperature happened due to air temperature, thermal index, air velocity, bird's age, daytime, and position of birds inside the experimental chambers. The surface temperatures were found lower under high air velocity treatment and higher under low air velocity treatment. During the afternoon time, the broilers' surface temperatures were higher than other times of the day. It was also found that the birds' surface temperature increased with age and temperature humidity indices. Based upon the experimental data of five flocks, a simple linear regression model was developed to predict surface temperature from the birds' age, thermal indices, and air velocity. It will help assess heavy broilers' thermal comfort under heat stress, which is essential to provide a comfortable environment for them.

Objective: To investigate the status of exposure to xylene and Formaldehyde of medical and technical personnel in Pathology Department of a hospital, and to provide references for prevention of occupational hazards. Methods: From July to October in 2019, 52 medical workers and working places in Pathology Department of a third-class hospital in Jiangxi Province were selected as survey objects, the distribution of occupational hazards, protective measures and personal protective equipment were investigated, and the control wind speed of Formaldehyde, xylene and ventilation facilities were detected and analyzed statistically. Results: It showed that the detection rate of xylene and formaldehyde was 82.1% (23/28) , and the detection rate of xylene C (STEL) in the two sampling posts was 14.3% (2/14) , the local suction device on each side and the control wind speed of the fume hood do not meet the national standards. Conclusion: It is necessary to strengthen the prevention and control of the occupational hazards in the Department of Pathology to prevent the occurrence of occupational diseases.

In order to clarify the influence of air velocity on the atomization effect of shearer external spray and optimize dust suppression performance, the dust removal experiment was carried out by utilizing the self-designed external spray experiment platform. The effect of three kinds of air velocity on the atomization effect of main spray parameters was investigated to clarify the influence of air velocity on the atomization effect of shearer external spray and optimize dust suppression performance. The results showed that the influence of air velocity on droplet size and distribution width of the droplet size was slightly less than the spray pressure. The average diameter of the droplet was 54.211 μm, and the particle size distribution of the droplet was more uniform and concentrated when air velocity was 2 m/s, the pressure was 5 MPa and nozzle diameter was 1.0 mm. When the air velocity was less than 2 m/s and the spray pressure was 3-5 MPa, the atomization effect was better by using 1.0 or 1.2 mm diameter nozzle. Through on-site applications and optimization, the leeward total dust removal efficiency of the shearer can reach 79.43%, and the maximum increase range can reach 18.51 percentage points. The respiratory dust removal efficiency of the shearer can reach 87.45%, and the maximum increase range can reach 11.87 percentage points.

Barn climate is believed to play a major role in the bovine respiratory disease complex. However, the exact air quality parameters associated with (sub)clinical pneumonia or airway inflammation in calves are currently unknown. The objective of this cross-sectional study was to assess associations of air quality parameters with clinical signs, lung consolidation, pulmonary inflammation and infection in group-housed calves. In total, 60 beef and dairy farms were visited from January to April 2017 and 428 calves sampled. Measured air quality parameters included continuous 24-h measurements of ammonia concentration, relative humidity and temperature and punctual measurements of air velocity, ammonia, CO 2 and bacterial air load. Calf sampling consisted of clinical examination, thoracic ultrasonography and broncho-alveolar lavage sampling for bacteriological and cytological analysis of broncho-alveolar lavage fluid (BALf). Average air temperature was 14.2 °C (standard deviation (SD) 4.4, range 5.5-23.9) and relative humidity 68.8 % (SD 8.9, range 52.2-91.6). Average ammonia concentration was 1.7 ppm (SD 0.9, range 0-10.0). Lung consolidations of ≥1 cm, ≥3 cm and ≥6 cm in depth were present in 41.1 % (176/428), 27.1 % (116/428) and 16.1 % (69/428) of the calves, respectively. Average pen temperature was positively associated with consolidations of ≥1 cm (P = 0.005), ≥3 cm (P = 0.002) and ≥6 cm (P < 0.01). Ammonia exposure, in hours>4 ppm, was associated with lung consolidation ≥1 cm (odds ratio (OR) = 1.73; confidence interval (CI) = 1.02-3.07; P = 0.04). Ammonia concentration was positively associated with BALf epithelial cell percentage (P = 0.01). Air velocity >0.8 m/s was associated with increased odds of lung consolidation of ≥3 cm (OR = 6.8; CI = 1.2-38.5; P = 0.04) and ≥6 cm (OR = 15.9; CI = 1.2-200.0; P = 0.03). The prevalence of lung consolidations ≥1 cm was higher in the draught (81.8 %; P = 0.0092) and warm, dry and ammonia accumulation clusters (54.2 %; P = 0.02) compared to the presumably normal cluster (31.6 %). In addition, in the warm, dry and ammonia cluster the prevalence of lung consolidations ≥3 cm (38.1 %; P = 0.04) and ≥6 cm (31.4 %; P = 0.01) in depth were higher compared to the presumably normal climate cluster (18.2 % and 9.1 %, respectively). Of all frequently measured indoor air quality parameters, only average temperature, ammonia concentration and air velocity were associated with pneumonia and might therefore be preferable for cost-effective evaluation of calf barn climate., (Copyright © 2020 Elsevier B.V. All rights reserved.)

Poultry facilities are going through an evolution in design due to growing demands for cage-free eggs and egg products without unified guidelines to accommodate these transitions. The goal of this study was to help builders and egg producers assess current ventilation design within cage-free production facilities for conditions that impact hen comfort and welfare. The method of evaluation was simulation of the indoor environment of a hen house via computational fluid dynamics (CFD) modeling with individual hens modeled at a typical stocking density. This paper describes the development of a three-dimensional model of a commercial floor-raised cage-free hen house that is cross-ventilated to document current environmental conditions. A one-eighth section of the barn was modeled at full-scale using existing ventilation schemes with each bird represented by a hen-shaped, heated, solid body. A conventional top-wall inlet, side-wall exhaust (TISE) ventilation configuration was modeled for this study. The simulated ventilation rate for the hen house was approximately 3 m 3 /h (1.77 ft 3 /min) per hen resulting in 7092 m 3 /h (4174 ft 3 /min) for the 2365 birds, which falls at the higher end of the desired cold weather (0 °C) ventilation range. Contours of airflow, temperature, and pressure were generated to visualize results. Three two-dimensional planes were created at representative cross-sections to evaluate the contours inside and outside the barn. Five animal-occupied zones within each of the model planes were evaluated for practical hen comfort attributes. The simulation output suggested the TISE standard ventilation system could limit air speed to a comfortable average of 0.26 m/s (51 ft/min) and the temperature could be maintained between 18 and 24 °C on average at the bird level. Additionally, the indoor static pressure difference was very uniform averaging -25 Pascal (0.1 inches of water), which falls in the normal range for a floor-raised hen house with negative-pressure ventilation during cold weather conditions. Findings confirmed that CFD modeling can be a powerful tool for studying ventilation system performance at the bird level, particularly when individual animals are modeled, to assure a comfortable indoor environment for animal welfare in poultry facilities.

To solve the problems that the borehole depth is shallow and the drilling efficiency is low during the gas drainage drilling in soft coal seam with current cuttings removal method, a new technology of reverse circulation pneumatic cuttings removal is proposed. The working principle of reverse circulation pneumatic cuttings removal is analyzed, and the kinetic equation of cuttings in the inner hole of the drill pipe is established. Through experiments, the pressure drop in the drill pipe is measured to reveal the effects of air velocity, cuttings mass flow rate, and cuttings particle size on the pressure drop in inner hole of the drill pipe. When the cuttings mass flow rate is constant, the pressure drop increases with the increase in air velocity. When the air velocity is constant, the pressure drop increases with the increase in cuttings mass flow rate. At low air velocity, the pressure drop of cuttings is primary. As the air velocity increases, the pressure drop ratio of cuttings decreases. Under the same conditions, the order of pressure drop with different particle size cuttings is coarse cuttings > medium cuttings > fine cuttings. Empirical equation of pressure drop coefficient of cuttings is established, which is in good agreement with the actual data.

A multi-fan system (MFS) for single culture beds was developed to improve the airflow in a plant factory with artificial light. The MFS had seven fans which were installed on both the front and back sides of culture beds to generate airflow from two opposite horizontal directions. The fans that push the air into the culture bed were air inlets while those that pull the air out of the culture bed were air outlets. In this study, three airflow patterns were evaluated: T 1 , the front and back sides of the culture bed were air inlets; T 2 , the front side was an air inlet and the backside was an air outlet; and T 3 , both the front and back sides were air outlets. A culture bed with no MFS was used as a control (T 4 ). Lettuce growth and tipburn occurrence were evaluated and leaf boundary layer resistance (1/g bv ), sensible heat flux (S h ), and latent heat flux (L h ) of lettuce plants were estimated. The airflow pattern in T 1 improved the air velocity (V a ) by an average of 0.75 m s -1 and a variation coefficient of 65%. The 1/g bv decreased significantly with the increase in V a , and the lowest value of 54.0 s m -1 was observed in T 1 . The low resistance to heat and moisture transfer enhanced the S h and L h of lettuce plants. The average S h and L h were 40% and 46% higher in T 1 compared with those in T 4 . The fresh and dry weights of lettuce plants in T 1 were 1.13 and 1.06 higher than those in T 4 , respectively. No tipburn occurrence was observed in lettuce plants grown under the MFS while five leaves per plant were injured with tipburn in T 4 . The results indicated that improving the airflow can improve the growth of indoor cultured lettuce and alleviate the occurrence of tipburn due to the decrease in the 1/g bv and the increase in the transpiration rate., Competing Interests: Declaration of competing interest None., (Copyright © 2019 Elsevier Ltd. All rights reserved.)

Due to the successful application of roof bolter canopy air curtains (CACs) to protect roof bolter operators from high levels of coal mine respirable dust, a shuttle car CAC is currently being developed. Since a shuttle car consistently trams from the continuous miner to the feeder and back at a speed up to 9.66 kph (6 mph) or 2.68 m/s (528 fpm), it is thought that the shuttle car may encounter very high air velocities (mine ventilation air velocity + max shuttle speed (2.68 m/s (528 fpm)). Past research and preliminary lab testing showed that CAC protection in high interference air velocities is difficult to achieve. Therefore, testing was conducted at a Midwestern US coal mine to determine the air velocities their shuttle car actually encounters. This mine used ram dump cars as their shuttle cars. Results showed that coal mine dust exposure is generally very low at the feeder and when tramming. Elevated concentrations are encountered at the ram dump car operator position when the car is being loaded by the continuous miner. Recorded air velocities while tramming did not reach the max air velocity of mine ventilation air velocity + 2.68 m/s (528 fpm) calculated as 3.32 m/s (653 fpm). High velocities, while encountered, were of low frequency and associated with low respirable coal mine dust concentrations. Therefore, using this new information, designing the shuttle car CAC for maximum interference air velocity may not be as important as previously thought.

Background: There has been little research on the performance of laminar airflow (LAF) and mixing ventilation (MV) systems regarding clean airflow distribution near a surgical patient in operating rooms (ORs). The objective of this study was to examine the performance of LAF and MV systems in ORs at St Olavs Hospital in Norway., Methods: Experimental measurements were conducted in 2 ORs equipped with LAF and MV systems., Results: Under real operating conditions, airflow distribution from the LAF system was disrupted, and airflow velocity became significantly lower than that of MV above the lying patient. Airflow pattern was observed as distributed vertically downward and horizontally with LAF and MV, respectively. Turbulence intensity of supply airflow from LAF was much lower than that of MV., Conclusions: The airflow distribution by LAF system in close proximity to a patient is greatly affected by thermal plumes generated above incisions by both patients and surgical facilities. The effect of surgical facilities on airflow distribution by using MV is not significant compared to LAF ventilation. New guidelines are needed for the design of clean airflow distribution systems in the vicinity of surgical patients in ORs., (Copyright © 2018 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Elsevier Inc. All rights reserved.)

Broiler chickens are selected to undergo a rapid six-week hatch-to-slaughter growth phase to attain large body and muscle mass. Broilers have relatively high resting and locomotor metabolic costs suggesting that adaptive thermoregulatory mechanisms are required to dissipate excess heat. Using thermal imaging in the growing broiler we characterised the trajectory of radiative and convective cooling in still air across broiler development. Scaling of head, tarsus and toe surface area did not deviate from body mass 2/3 while torso area increased with positive allometry, body mass 0.82 , reflecting increased feather coverage and/or disproportionate abdominal/thoracic growth. Despite relatively increased area, the body became less effective for heat transfer presumably due to increasing feather coverage. Conversely, the magnitude of heat exchange from the distal hindlimbs was improved in larger birds. Overall capacity to transfer heat by convection and radiation in still air was attenuated over development, since the proportion of resting metabolic rate accounted for decreased in standing and sitting postures. This physiological constraint could be ameliorated by increased latent heat transfer or provision of environmental ventilation, which we modelled according to industrial guidelines. Based on models, higher airspeeds coincided with improved convective cooling that assisted in maintaining the proportion of RMR accounted for by convective and radiative heat transfer. These data highlight the potentially adverse thermoregulatory effects of rapid growth rate and body mass increases, which may contribute to the increased sedentary resting and decreased locomotor behaviour observed in large broilers., (Copyright © 2018 Elsevier Ltd. All rights reserved.)

Background: Airflow distribution in the operating room plays an important role in ensuring a clean operating microenvironment and preventing surgical site infections (SSIs) caused by airborne contaminations. The objective of this study was to characterize the airflow distribution in proximity to a patient in an orthopedic operating room., Methods: Experimental measurements were conducted in a real operating room at St. Olav's Hospital, Norway, with a laminar airflow system. Omnidirectional anemometers were used to investigate the air distribution in the operating zone, and 4 different cases were examined with a real person and a thermal manikin., Results: This study showed that the downward airflow from the laminar airflow system varies in each case with different surgical arrangement, such as the position of the operating lamp. The results indicate that the interaction of thermal plumes from a patient and the downward laminar airflow may dominate the operating microenvironment., Conclusions: The airflow distribution in proximity to a patient is influenced by both the surgical facility and the presence of medical staff. A thermal manikin may be an economical and practical way to study the interaction of thermal plumes and downward laminar airflow. The provision of higher clean airflow rate in the operating microenvironment may be an effective way to prevent the development of SSIs caused by indoor airborne contamination., (Copyright © 2018 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Elsevier Inc. All rights reserved.)

The application of power ultrasound (PuS) could be used as a novel technology with which to intensify thermal treatments using hot air. Mild thermal treatments have been applied to improve the soft texture of dry-cured ham caused by defective processing. In this regard, the aim of this study was to assess the kinetic intensification linked to the application of airborne PuS in the mild thermal treatment using hot air of dry-cured ham. For this purpose, vacuum packed cylindrical samples (2.52±0.11cm in diameter and 1.90±0.14cm in height) of dry-cured ham were heated using hot air at different temperatures (40, 45, 50°C) and air velocities (1, 2, 3, 4, 6m/s) with (22.3kHz, 50W) and without PuS application. Heat transfer was analyzed by considering that it was entirely controlled by conduction and the apparent thermal diffusivity was identified by fitting the model to the heating kinetics. The obtained results revealed that PuS application sped up the heat transfer, showing an increase in the apparent thermal diffusivity (up to 37%). The improvement in the apparent thermal diffusivity produced by PuS application was greater at high temperatures (50°C) but negligible at high air velocities (6m/s). Heating caused an increase in the hardness and elasticity of dry-cured ham, which would correct ham pastiness defects, while the influence of PuS on such textural parameters was negligible., (Copyright © 2017 Elsevier B.V. All rights reserved.)

In cold storage facilities of fruit and vegetables, airflow is necessary for heat removal. The design of storage facilities influences the air speed in the surrounding of the product. Therefore, knowledge about airflow next to the product is important to plan the layout of cold stores adapted to the requirements of the products. A new sensing device (ASL, Air speed logger) is developed for omnidirectional measurement of air speed between fruit or vegetables inside storage bins or in bulk. It consists of four interconnected plastic spheres with 80 mm diameter each, adapted to the size of apple fruit. In the free space between the spheres, silicon diodes are fixed for the airflow measurement based on a calorimetric principle. Battery and data logger are mounted inside the spheres. The device is calibrated in a wind tunnel in a measuring range of 0-1.3 m/s. Air speed measurements in fruit bulks on laboratory scale and in an industrial fruit store show air speeds in gaps between fruit with high stability at different airflow levels. Several devices can be placed between stored products for determination of the air speed distribution inside bulks or bin stacks in a storage room., Competing Interests: The authors declare no conflict of interest.

The wet bulb globe temperature (WBGT) is an effective measure for risk screening to prevent heat dISOrders. However, a heat risk evaluation by WBGT requires adjustments depending on the clothing. In this study, we proposed a new effective WBGT (WBGT eff * ) for general vapor permeable clothing ensembles and vapor impermeable protective clothing that is applicable to occupants engaged in moderate intensity work with a metabolic heat production value of around 174W/m 2 . WBGT eff * enables the conversion of heat stress into the scale experienced by the occupant dressed in the basic clothing ensemble (work clothes) based on the heat balances for a human body. We confirmed that WBGT eff * in outdoor conditions with a solar load, the weighting ratio of globe temperature increased and that of air temperature decreased with air velocity. Approximation equations of WBGT eff * , we succeeded in clarifying how the weights for natural wet bulb, globe, and air temperatures and the intercept changed depending on clothing properties and the surrounding environmental factors when heat stress is expressed by the weighted sum of natural wet bulb, globe, and air temperatures and the intercept. The weight of environmental temperatures (globe and air temperatures) for WBGT eff * for vapor impermeable protective clothing increased compared with that for general vapor permeable clothing, whereas that of the natural wet bulb temperature decreased. For WBGT eff * in outdoor conditions with a solar load, the weighting ratio of globe temperature increased and that of air temperature decreased with air velocity. Approximation equations of WBGT eff * were proposed for both general vapor permeable clothing ensembles and for vapor impermeable protective clothing., (Copyright © 2017 Elsevier Ltd. All rights reserved.)

Air pollution is one of the main factors that affect the air quality in aircraft cabins, and the use of different air supply modes could influence the distribution of air pollutants in cabins. Based on the traditional ceiling air supply mode used on the B737NG, this study investigated another 3 different kinds of air supply modes for comparison: luggage rack air supply mode, joint mode combining ceiling and luggage rack air supply, and joint mode combining ceiling and individual air supply. Under the above 4 air supply modes, the air velocity, temperature and distribution of air pollutants in a cabin full of passengers were studied using computational fluid dynamics (CFD), and carbon dioxide (CO 2 ) and formaldehyde were selected as 2 kinds of representative air pollutants. The simulation results show that the joint mode combining ceiling and individual air supply can create a more uniform distribution of air velocity and temperature, has a better effect on the removal of CO 2 and formaldehyde, and can provide better air quality in cabins than the other 3 modes., (Copyright © 2016. Published by Elsevier B.V.)

The former use of polychlorinated biphenyls (PCBs) in construction materials can lead to elevated indoor air concentrations. We studied the partitioning of PCB congeners between indoor air and silicone with a view to establish passive sampling of PCBs. The release of PCB congeners from silicone followed first order kinetics and confirmed air-side rate-limited mass transfer. Logarithmic elimination rate constants decreased linearly with the logKOA values of the PCB congeners, but varied in a non-linear way with air velocity. Linear uptake of PCBs was found for silicone disks (0.5 mm thickness) in a petri dish, while PCBs reached equilibrium in silicone-coated paper sheets (0.001 mm silicone on each side) exposed to indoor air for 1-2 weeks. The ratios of equilibrium concentrations in silicone and conventionally measured air concentrations were roughly comparable with silicone-air partition coefficients, but further research is required for the determination of silicone-air partition coefficients. Avoiding performance reference compounds (PRCs) because of the indoor setting, the two formats were calibrated against conventional active measurements. Comparisons of air concentrations derived from active and kinetic passive sampling showed a divergence by factors of 2.4 and 2.0 (median values) for the petri dishes and the silicone-coated paper, respectively. With promising results for sensitivity and precision, the calibration of kinetic passive samplers remains the main challenge and will need suitable, non-hazardous PRCs. Equilibrium sampling indicated promising alternatives., (Copyright © 2016 Elsevier Ltd. All rights reserved.)

Gaspers installed in commercial airliner cabins are used to improve passengers' thermal comfort. To understand the impact of gasper airflow on the air quality in a cabin, this investigation measured the distributions of air velocity, air temperature, and gaseous contaminant concentration in five rows of the economy-class section of an MD-82 commercial aircraft. The gaseous contaminant was simulated using SF6 as a tracer gas with the source located at the mouth of a seated manikin close to the aisle. Two-fifths of the gaspers next to the aisle were turned on in the cabin, and each of them supplied air at a flow rate of 0.66 l/s. The airflow rate in the economy-class cabin was controlled at 10 l/s per passenger. Data obtained in a previous study of the cabin with all gaspers turned off were used for comparison. The results show that the jets from the gaspers had a substantial impact on the air velocity and contaminant transport in the cabin. The air velocity in the cabin was higher, and the air temperature slightly more uniform, when the gaspers were on than when they were off, but turning on the gaspers may not have improved the air quality., (© 2015 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.)

Intact spores and submicrometer size fragments are released from moldy building materials during growth and sporulation. It is unclear whether all fragments originate from fungal growth or if small pieces of building materials are also aerosolized as a result of microbial decomposition. In addition, particles may be formed through nucleation from secondary metabolites of fungi, such as microbial volatile organic compounds (MVOCs). In this study, we used the elemental composition of particles to characterize the origin of submicrometer fragments released from materials contaminated by fungi. Particles from three fungal species (Aspergillus versicolor, Cladosporium cladosporioides and Penicillium brevicompactum), grown on agar, wood and gypsum board were aerosolized using the Fungal Spore Source Strength Tester (FSSST) at three air velocities (5, 16 and 27 m/s). Released spores (optical size, dp ≥ 0.8 μm) and fragments (dp ≤ 0.8 μm) were counted using direct-reading optical aerosol instruments. Particles were also collected on filters, and their morphology and elemental composition analyzed using scanning electron microscopes (SEMs) coupled with an Energy-Dispersive X-ray spectroscopy (EDX). Among the studied factors, air velocity resulted in the most consistent trends in the release of fungal particles. Total concentrations of both fragments and spores increased with an increase in air velocity for all species whereas fragment-spore (F/S) ratios decreased. EDX analysis showed common elements, such as C, O, Mg and Ca, for blank material samples and fungal growth. However, N and P were exclusive to the fungal growth, and therefore were used to differentiate biological fragments from non-biological ones. Our results indicated that majority of fragments contained N and P. Because we observed increased release of fragments with increased air velocities, nucleation of MVOCs was likely not a relevant process in the formation of fungal fragments. Based on elemental composition, most fragments originated from fungi, but also fragments from growth material were detected., (Copyright © 2015 Elsevier B.V. All rights reserved.)

The main objective of this study was to examine the performance of protected zone ventilation (PZV) and hybrid protected zone ventilation (HPZV) to reduce the direct exposure to exhaled air from others' breathing. Experimental measurements are carried out to test the performance of PZV in a full-scale office room with two breathing thermal manikins. The measurements were performed under three configurations, including two standing manikins at different distances: 0.35, 0.5, and 1.1 m. When the supply air velocity is increased to 4 m/s in the downward plane jet, the dimensionless concentration is 40% lower than for fully mixed ventilation, which can be considered as a measure of protection from the zoning condition. The measurement results showed that in both the PZV and the HPZV system it is possible to decrease the transmission of tracer gas from one manikin to the opposite manikin; therefore, it probably would reduce the risk of air borne cross-infection between two people at the same relative positions. The results suggest that PZV and HPZV may be used to reduce the exposure of people in a protected zone from indoor pollutants emitted in a source zone., (© 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.)

This study aimed to compare the dynamics of air temperature and velocity under two different ventilation and housing systems during summer and winter in Korea. The NH3 concentration of both housing systems was also investigated in relation to the pig's growth. The ventilation systems used were; negative pressure type for the enclosed pig house (EPH) and natural airflow for the conventional pig house (CPH). Against a highly fluctuating outdoor temperature, the EPH was able to maintain a stable temperature at 24.8 to 29.1°C during summer and 17.9 to 23.1°C during winter whilst the CPH had a wider temperature variance during summer at 24.7 to 32.3°C. However, the temperature fluctuation of the CPH during winter was almost the same with that of EPH at 14.5 to 18.2°C. The NH3 levels in the CPH ranged from 9.31 to 16.9 mg/L during summer and 5.1 to 19.7 mg/L during winter whilst that of the EPH pig house was 7.9 to 16.1 mg/L and 3.7 to 9.6 mg/L during summer and winter, respectively. These values were less than the critical ammonia level for pigs with the EPH maintaining a lower level than the CPH in both winter and summer. The air velocity at pig nose level in the EPH during summer was 0.23 m/s, enough to provide comfort because of the unique design of the inlet feature. However, no air movement was observed in almost all the lower portions of the CPH during winter because of the absence of an inlet feature. There was a significant improvement in weight gain and feed intake of pigs reared in the EPH compared to the CPH (p<0.05). These findings proved that despite the difference in the housing systems, a stable indoor temperature was necessary to minimize the impact of an avoidable and highly fluctuating outdoor temperature. The EPH consistently maintained an effective indoor airspeed irrespective of season; however the CPH had defective and stagnant air at pig nose level during winter. Characteristics of airflow direction and pattern were consistent relative to housing system during both summer and winter but not of airspeed. The ideal air velocity measurement favored the EPH and therefore can be appropriate for the Korean environment. Further emphasis on its cost effectiveness will be the subject of future investigations.

The flow of air generated by a new design of air assisted sprayer equipped with two axial fans of reversed rotation was analyzed. For this goal, a 3D sonic anemometer has been used (accuracy: 1.5%; measurement range: 0 to 45 m/s). The study was divided into a static test and a dynamic test. During the static test, the air velocity in the working vicinity of the sprayer was measured considering the following machine configurations: (1) one activated fan regulated at three air flows (machine working as a traditional sprayer); (2) two activated fans regulated at three air flows for each fan. In the static test 72 measurement points were considered. The location of the measurement points was as follow: left and right sides of the sprayer; three sections of measurement (A, B and C); three measurement distances from the shaft of the machine (1.5 m, 2.5 m and 3.5 m); and four measurement heights (1 m, 2 m, 3 m and 4 m). The static test results have shown significant differences in the module and the vertical angle of the air velocity vector in function of the regulations of the sprayer. In the dynamic test, the air velocity was measured at 2.5 m from the axis of the sprayer considering four measurement heights (1 m, 2 m, 3 m and 4 m). In this test, the sprayer regulations were: one or two activated fans; one air flow for each fan; forward speed of 2.8 km/h. The use of one fan (back) or two fans (back and front) produced significant differences on the duration of the presence of wind in the measurement point and on the direction of the air velocity vector. The module of the air velocity vector was not affected by the number of activated fans.

The rearing of poultry for meat production (broilers) is an agricultural food industry with high relevance to the economy and development of some countries. Periodic episodes of extreme climatic conditions during the summer season can cause high mortality among birds, resulting in economic losses. In this context, ventilation systems within poultry houses play a critical role to ensure appropriate indoor climatic conditions. The objective of this study was to develop a multisensor system to evaluate the design of the ventilation system in broiler houses. A measurement system equipped with three types of sensors: air velocity, temperature and differential pressure was designed and built. The system consisted in a laptop, a data acquisition card, a multiplexor module and a set of 24 air temperature, 24 air velocity and two differential pressure sensors. The system was able to acquire up to a maximum of 128 signals simultaneously at 5 second intervals. The multisensor system was calibrated under laboratory conditions and it was then tested in field tests. Field tests were conducted in a commercial broiler farm under four different pressure and ventilation scenarios in two sections within the building. The calibration curves obtained under laboratory conditions showed similar regression coefficients among temperature, air velocity and pressure sensors and a high goodness fit (R(2) = 0.99) with the reference. Under field test conditions, the multisensor system showed a high number of input signals from different locations with minimum internal delay in acquiring signals. The variation among air velocity sensors was not significant. The developed multisensor system was able to integrate calibrated sensors of temperature, air velocity and differential pressure and operated successfully under different conditions in a mechanically-ventilated broiler farm. This system can be used to obtain quasi-instantaneous fields of the air velocity and temperature, as well as differential pressure maps to assess the design and functioning of ventilation system and as a verification and validation (V&V) system of Computational Fluid Dynamics (CFD) simulations in poultry farms.

This investigation sought to determine if cycling power could be accurately modeled. A mathematical model of cycling power was derived, and values for each model parameter were determined. A bicycle-mounted power measurement system was validated by comparison with a laboratory ergometer. Power was measured during road cycling, and the measured values were compared with the values predicted by the model. The measured values for power were highly correlated (R 2 = .97) with, and were not different than, the modeled values. The standard error between the modeled and measured power (2.7 W) was very small. The model was also used to estimate the effects of changes in several model parameters on cycling velocity. Over the range of parameter values evaluated, velocity varied linearly (R 2 > .99). The results demonstrated that cycling power can be accurately predicted by a mathematical model.