Search

This work presents a unique approach to the design, fabrication, and characterization of paper-based origami robotic systems consisting of stackable pneumatic actuators. These paper-based actuators (PBAs) use materials with high elastic modulus-to-mass ratios, accordion-like structures, and direct coupling with pneumatic pressure for extension and bending. The study contributes to the scientific and engineering understanding of foldable components under applied pneumatic pressure by constructing stretchable and flexible structures with intrinsically nonstretchable materials. Experiments showed that a PBA possesses a power-to-mass ratio greater than 80 W/kg, which is more than four times that of human muscle. This work also illustrates the stackability and functionality of PBAs by two prototypes: a parallel manipulator and a legged locomotor. The manipulator consisting of an array of PBAs can bend in a specific direction with the corresponding actuator inflated. In addition, the stacked actuators in the manipulator can rotate in opposite directions to compensate for relative rotation at the ends of each actuator to work in parallel and manipulate the platform. The locomotor rotates the PBAs to apply and release contact between the feet and the ground. Furthermore, a numerical model developed in this work predicts the mechanical performance of these inflatable actuators as a function of dimensional specifications and folding patterns. Overall, we use stacked origami actuators to implement functionalities of manipulation, gripping, and locomotion as conventional robotic systems. Future origami robots made of paper-like materials may be suitable for single use in contaminated or unstructured environments or low-cost educational materials.

Chronic pancreatitis is associated with impaired quality of life, high incidence of comorbidities, serious complications and mortality. Healthcare costs are exorbitant. Some medical societies have developed guidelines for treatment based on scientific evidence, but the gathered level of evidence for any individual topic is usually low and, therefore, recommendations tend to be vague or weak. In the present position papers on chronic pancreatitis from the Societat Catalana de Digestologia and the Societat Catalana de Pàncrees we aimed at providing defined position statements for the clinician based on updated review of published literature and on multidisciplinary expert agreement. The final goal is to propose the use of common terminology and rational diagnostic/therapeutic circuits based on current knowledge. To this end 51 sections related to chronic pancreatitis were reviewed by 21 specialists from 6 different fields to generate 88 statements altogether. Statements were designed to harmonize concepts or delineate recommendations. Part 2 of these paper series discuss topics on treatment and follow-up. The therapeutic approach should include assessment of etiological factors, clinical manifestations and complications. The complexity of these patients advocates for detailed evaluation in multidisciplinary committees where conservative, endoscopic, interventional radiology or surgical options are weighed. Specialized multidisciplinary units of Pancreatology should be constituted. Indications for surgery are refractory pain, local complications, and suspicion of malignancy. Enzyme replacement therapy is indicated if evidence of exocrine insufficiency or after pancreatic surgery. Response should be evaluated by nutritional parameters and assessment of symptoms. A follow-up program should be planned for every patient with chronic pancreatitis. © 2021 Elsevier España, S.L.U.

In recent decades, there has been a growing interest in the recycling of organic materials such as paper mill biosolids (PB) and biochar for use as soil amendments. However, the benefits of co-application of PB and biochar and its effects on soil phosphorus (P) availability remain unknown. An incubation study was conducted on two acidic soils to assess the effect of two PB types (2.5% w/w) co-applied with three rates (0%, 2.5%, and 5% w/w) of pine (Pinus strobus L.) biochar on soil P fractions. An unfertilized control and a mineral NP fertilizer were used as a reference. Soil P fractions were determined by Hedley procedure after 2 and 16 wk of incubation. Material fractionation indicated that the PB containing the highest total P and the lowest Al content had the highest proportion of labile P, whereas most P in the biochar was in a stable form. The incubation study revealed that the P-rich PB increased P availability in both soils to a level comparable to mineral fertilizer at the end of the incubation. The addition of biochar to PB, however, did not affect soil P availability, but the highest rate induced a conversion of P fixed to Al and Fe oxides towards recalcitrant forms, particularly in the sandy loam soil. We conclude that co-applying biochar and PB could be more beneficial than application biochar alone and soils amended with such a mixture would be expected to release part of their P slowly over a longer period of time.

Objective The purpose of this study was to develop a natural language processing (NLP) pipeline to identify incidental thyroid nodules (ITNs) meeting criteria for sonographic follow-up and to assess both adherence rates to white paper recommendations and downstream outcomes related to these incidental findings. Methods 21583 non-contrast chest CT reports from 2017 and 2018 were retrospectively evaluated to identify reports which included either an explicit recommendation for thyroid ultrasound, a description of a nodule ≥ 1.5 cm, or description of a nodule with suspicious features. Reports from 2018 were used to train an NLP algorithm called fastText for automated identification of such reports. Algorithm performance was then evaluated on the 2017 reports. Next, any patient from 2017 with a report meeting criteria for ultrasound follow-up was further evaluated with manual chart review to determine follow-up adherence rates and nodule-related outcomes. Results NLP identified reports with ITNs meeting criteria for sonographic follow-up with an accuracy of 96.5% (95% CI 96.2-96.7) and sensitivity of 92.1% (95% CI 89.8-94.3). In 10006 chest CTs from 2017, ITN follow-up ultrasound was indicated according to white paper criteria in 81 patients (0.8%), explicitly recommended in 46.9% (38/81) of patients, and obtained in less than half of patients in which it was appropriately recommended (17/35, 48.6%). Discussion NLP accurately identified chest CT reports meeting criteria for ITN ultrasound follow-up. Radiologist adherence to white paper guidelines and subsequent referrer adherence to radiologist recommendations showed room for improvement.

The prevalence of diabetes has increased over the past years. Therefore, developing minimally invasive, user-friendly and cost-effective glucose biosensors is necessary especially in low-income and developing countries. Cellulose paper-based analytical devices have attracted the attention of many researchers due to affordability, not requiring trained personnel, and complex equipment. This paper describes a microfluidic paper-based analytical device for the detection of glucose in tear with the naked eye. The paper-based biosensor fabricated by laser CO2, and GOx/HRP enzymatic solution coupled with TMB was utilized as reagents. A sample volume of 10 µl was needed for the biosensor operation and the results were observable within 5 minutes. To evaluate the device performance, color intensity-based and distance-based results were analyzed by ImageJ and Tracker. Distance-based results showed a linear behavior in the range of 0.1–0.6 mM with an R2 = 0.967 and LOD of 0.2 mM. The results could be perceived by the naked eye without any need to further equipment or trained personnel in a relatively short time (3–5 minutes). Moreover, glucose concentration could be obtained non-invasively by tears collected by this µPAD.

This study gives a first insight into the use of wood flour as a plant-based and cellulosic-based alter-native additive for newsprint and paperboard production using 100% recycled fibers as a raw material. The study compares four varieties of a spruce wood flour product serving as cellulosic-based additives at addition rates of 2%, 4%, and 6% during operation of a 12-in. laboratory pilot paper machine. Strength properties of the produced newsprint and linerboard products were analyzed. Results suggested that spruce wood flour as a cellulosic-based additive represents a promising approach for improving physical properties of paper and linerboard products made from 100% recycled fiber content. This study shows that wood flour pretreated with a plant-based polysaccharide and untreated spruce wood flour product with a particle size range of 20 μm to 40 μm and 40 μm to 70 μm can increase the bulk and tensile properties in newsprint and linerboard applications.

Amending croplands with forest residues may help in restoring soil properties in fields subject to intensive land management. Despite their known benefits when applied separately, co-application of wood biochar with paper mill biosolids (PB) has seen little investigation under field conditions. A study was initiated in Québec, QC, Canada, to determine the effect of a single application of wood biochar with and without PB on the nitrogen (N) and phosphorus (P) availability of two pH-neutral to alkaline loamy soils. Biochar at 0, 10, and 20 Mg dry weight·ha−1 and PB at 30 Mg wet weight·ha−1 were applied before planting of corn (Zea mays L.) and soybean [Glycine max (L.) Merr.] in 2018. Residual effect of this co-application was determined under soybean and corn in the subsequent year. In both years, corn received supplemental N and P from mineral fertilizers according to local agronomic recommendations. Co-applying biochar and PB reduced soil NO3-N availability in the year of application and decreased corn yield by 1.0 Mg·ha−1 compared with biochar or PB applied alone, but these amendments did not affect soybean yields. In the following year, the previous biochar addition increased soybean yield by 0.6 Mg·ha−1 but had little effect on corn. For both years, biochar addition induced a large increase in soil Mehlich-3 P. This study revealed that wood biochar positively impacted P status of these soils but was not a source of N to crops even when co-applied with PB.

Acidification and metal mobility may present challenges in soil receiving paper mill biosolids (PB). Co-applying biochar and PB could help prevent these issues, but its effect must be assessed. The objective of this 224 d incubation study was to evaluate the effect of amending two acidic soils, a clay and sandy loam, with two PB types varying in pH (PB1, pH = 7.80; and PB2, pH = 4.51) co-applied with three rates (0%, 2.5%, and 5% w/w) of pine (Pinus strobus L.) biochar on soil pH and macro- (P, K, Ca, and Mg) and micronutrients (Cu, Zn, Fe, and Mn). In both soils, co-applying biochar and PB significantly increased soil pH and extractable K concentration compared with PB-only application, whereas amending with PB significantly increased soil extractable P concentration compared with the unamended soil. In comparison with PB only, co-applying 5% biochar and PB decreased extractable Cu concentration in both soils and extractable Fe concentration in the sandy loam soil. This study showed that co-applying biochar and PB can be more beneficial to agricultural soils than application of PB alone by supplying nutrients and helping prevent metal toxicity by raising pH, especially in acidic sandy soils.

Molybdenum sulfide (MoS2) with well-designed porous structure has the potential to be great electrode materials in sodium-ion batteries due to its high theoretical capacity and abundant resource, however, hindered by its intrinsic low conductivity and stability. Herein, MoS2 with 3D macroporous foam structure and high conductivity was obtained through SiO2 templates and integrated with carbon paper (3D F-MoS2/CP). It has showed superior specific capacity (225 mA h g−1, 0.4–3 V) and cycling stability (1000 cycles) at high rate (2000 mA g−1), with a low decay rate (0.033% per cycle) in sodium-ion batteries. The excellent electrochemical performance may originate from its unique integrated structure: 3D MoS2 macropores providing high surface area and abundant transfer channels while carbon paper enhancing the conductivity of MoS2 and avoiding unnecessary side reactions brought by binder addition.

Purpose This study aimed to determine whether continual electronic patient-reported outcome (ePRO) measurements at home can capture the fluctuations in health-related quality of life (HRQOL) scores between visits. Methods We performed a randomized controlled trial to compare the scores obtained by standard practice (paper-based measurements in the hospital) to scores by continuous measurement of ePRO at home. Metastatic cancer patients were randomly assigned to either the paper-based ( n = 50) or the ePRO group ( n = 52). EQ-5D-5L and EORTC QLQ C-30 scores were obtained on 3 different chemotherapy days in the paper-based group. Meanwhile, scores were obtained on the chemotherapy day and on days 3, 7, 10, and 14 in the ePRO group during 2 cycles. The first hypothesis of our study was that both scores at the same time points would be equivalent despite different measurement frequency, place, or mode of measurement. The second hypothesis was that PRO score–adjusted time would be different between the groups. For equivalence, the endpoint was the mean EQ-5D-5L index value on the chemotherapy day before the outpatient treatment. Only if equivalence was shown, quality-adjusted life-days (QALDs) were considered using all the data. Results The adjusted mean difference in the EQ-5D-5L index was determined to be −0.013 (95% confidence interval [CI]: −0.049 to 0.022); the 95% CI did not exceed the equivalence margin. Similarly, the mean difference in global health status (2.28 [95% CI: −2.55 to 7.11]) also showed equivalence. However, the QALD by EQ-5D-5L was significantly lower in the ePRO group by 1.36 per 30 d (95% CI: −2.22 to −0.51; P = 0.0021). Conclusions Continual measurements of the HRQOL at home by ePRO may yield more detailed profiles of the HRQOL.

Paper mill effluent has been characterized as recalcitrant because of containing lignin and its derivatives. Since biofilm system exhibits a notable potential for the removal of recalcitrant contaminants, a sequencing batch biofilm reactor (SBBR) was employed to treat coagulated recycled paper mill effluent in this study. The results indicated that the SBBR removed 91.3 % of chemical oxygen demand (COD), whilst total suspended solid (TSS) and color removal reached 83.1 % and 71.0 %, respectively. The microbial analysis suggested that three typical heterotrophic phyla, Proteobacteria, Bacteroidetes and Acidobacteria are dominant bacteria and reflected the removal of recalcitrant contaminants. The COD removal rate of SBBR is evidently superior to conventional activated sludge process due to high sludge concentration as well as long sludge retention time (SRT). Whilst the problem of sludge bulking can be successfully avoided, the blockage of reactor caused by TSS accumulation and microbial growth deserve further investigation.

Background The screening of biological hazards, chemical contaminants and allergens in food products is a major concern of food industry since they can cause serious illnesses and even lead to death. Therefore, there is a significant interest in developing low-cost, robust, and rapid detection methods for food safety and quality analysis. Conventional methods provide accurate analytical characteristics, but require well-equipped laboratories, trained personnel, costly reagents, and complicated sample preparation procedures prior to the detection in order to obtain reliable results. Hence, they are not always ideal for on-site food surveillance. Scope and approach This paper discusses the fundamentals of microfluidic paper-based analytical devices (μPADs) and reviews the recent progress in their usage for screening biological hazards, harmful chemical residues, and allergens in food products to systematically evaluate the strengths and weaknesses of this technology. It then covers future trends and useful strategies that could be employed in μPADs design and fabrication procedures to address the critical challenges in equipment-free food analysis. Key findings and conclusions μPADs offer promising avenues to revolutionize food safety and quality analysis with merits of equipment-free sample preparation and detection at low-cost. Despite the advancement in the microfluidic technology, the manufacturing of user-friendly sample-to-answer μPADs still requires intensive research studies to be employed for robust and sensitive food safety and quality analysis.

Laser-induced graphene (LIG) technology featuring low-cost, high-efficiency and scalability has presented great advantages in micro-supercapacitors (MSCs) fabrication. However, the limited capacitance of LIG based MSCs is still hindering their further development. Herein, we introduce joule heating as a critical in-situ treatment merged with the assembly of laser-induced graphene paper based MSCs (LIGP-MSCs) toward capacitive enhancement. By increasing heating-treatment temperature from ∼20 to 500 °C, the number of nanopores in LIGP continuously increases, attributed to the gradual decomposition of amorphous carbon components. The resulting joule-heated LIGP (J-LIGP) with improved specific surface area (160.97–533.49 m2/g) and pore volume (0.179–0.553 cm3/g) as well as superhydrophilic surface is highly suitable to be employed as J-LIGP-MSCs microelectrodes. By investigating process dependent performance, the J-LIGP-MSCs heated at 500 °C for 60 min delivers a significantly improved specific areal capacitance (CA) of 13.71 mF/cm2 at 10 mV/s, which is approximately six-fold higher than that of unheated LIGP-MSCs. By further exploring and optimizing the process efficiency, J-LIGP-MSCs with a CA of 12.61 mF/cm2 has been achieved by 550 °C heating for only 5 min. Along with superior mechanical flexibility, cyclability and structural modularity, the proposed in-situ joule heating treatment is finally proved to be a universal approach for consistently enhancing the CA of LIG based MSCs processed under various chemical modifications.

Antimicrobial stewardship programs (ASPs) have made immense strides in optimizing antibiotic, antifungal, and antiviral use in clinical settings. However, although ASPs are required institutionally by regulatory agencies in the United States and Canada, they are not mandated for transplant centers or programs specifically. Despite the fact that solid organ transplant recipients in particular are at increased risk of infections from multidrug-resistant organisms, due to host and donor factors and immunosuppressive therapy, there currently are little rigorous data regarding stewardship practices in solid organ transplant populations, and thus, no transplant-specific requirements currently exist. Further complicating matters, transplant patients have a wide range of variability regarding their susceptibility to infection, as factors such as surgery of transplant, intensity of immunosuppression, and presence of drains or catheters in situ may modify the risk of infection. As such, it is not feasible to have a “one-size-fits-all” style of stewardship for this patient population. The objective of this white paper is to identify opportunities, risk factors, and ASP strategies that should be assessed with solid organ transplant recipients to optimize antimicrobial use, while producing an overall improvement in patient outcomes. We hope it may serve as a springboard for development of future guidance and identification of research opportunities.

Mitigation of global warming, energy security and industrial competitiveness urge the energy-intensive pulp and paper industry (PPI) to transform energy use practices. This study investigates how the PPI has responded to the need for the energy transition in the 2000s. Finland and Sweden as forerunners of energy-efficient operation and decarbonization of the PPI are used as target countries. Understanding of changes in energy consumption is complemented using decomposition analysis (Logarithmic Mean Divisia Index Method) and the energy efficiency index approach. Analysis of companies’ investments in energy technologies is used for explaining changes in energy production. Evidence of significant development towards the more sustainable operation of the PPI was found. Energy consumption per produced unit has decreased, i.e., energy efficiency has improved. Fossil fuels have been partially replaced with bio-based alternatives. Thus, the CO2 intensity has decreased substantially. The generation of renewable electricity has increased in both countries. Examples of Finland and Sweden indicate that the PPI has great potential to contribute to CO2 emission reduction worldwide in the future as energy efficiency can be further improved, and the share of fossil fuels can be decreased increasing the use of biofuels and self-generated green electricity at least in kraft pulp mills.

We present how harmful different wood extractives carried over to paper mill with unbleached softwood Kraft pulp are for the strength of packaging papers and boards. The investigations were done by simulating industrial papermaking conditions in laboratory-scale trials for handsheet production. It was found that fatty acids are the most relevant compounds in the carryover pitch extractives (CPEs), as they readily interfere in fiber–fiber bonding strength, control the properties of CPE micelles, and are furthermore the most abundant compounds. Addition of cationic starch improved strength and evened out the strength differences of handsheets with different CPE compounds. Oleic acid (unsaturated fatty acid) was an exception, as it was above average harmful for paper strength without cationic starch and also heavily impaired the functioning of cationic starch. As a whole, these findings demonstrate that fatty acids, especially unsaturated ones, are the most relevant CPE compounds contributing to the reduced efficiency of cationic starch and decreased strength of unbleached softwood Kraft paper. This makes the cleaning of process waters by precipitating CPEs on the pulp fibers harmful for paper strength.

Biodegradable paper cups coated with rice bran wax and whey protein isolate were designed to package popcorn. Coatings with different concentrations of whey protein isolate (5.5, 7.75, and 10% w/v) and rice bran wax (0.2, 0.4, and 0.6% w/v) were applied on the outer surface of the paper cups. Thickness, color changes, Young's modulus and tensile strength, water vapor transmission rate (WVTR) of the coated and uncoated cups, and also popcorns properties (pH, texture, and sensory properties) were evaluated. Water vapor transmission rate, Young's modulus, thickness, total color change index, and tensile strength of coated cups with the optimal coating formulation was 19.785 (g/m2 day), 11.810 (MPa), 276.583 (µm), 1.839, and 11.222 (MPa), respectively. The results showed that paper cup coating increased thickness and yellowness and reduced the brightness, Young's modulus, and WVTR. Coating had a positive effect on the pH and texture of popcorns packaged in coated cups than samples packed in uncoated cups (p, Biodegradable packaging is one of the best types of packaging that wishes not to harm the environment. Paper packaging coated with materials, such as rice bran wax and whey protein isolate, both of which are food waste, can improve paper color and resistance, and provide a good moisture barrier. This type of coating can be used in paper packaging of food such as snacks, noodle packaging, semi‐prepared foods, etc. This type of packaging can also maintain the physicochemical and sensory properties of food for a long time. Also, due to the edible nature of this type of coating, this coating can be used inside the package so that the printability of the packaging surface is not affected.

Paper cultural relics such as double-sided printed newspapers and periodicals represent modern cultural heritage. Severe damage such as embrittlement, decay, and dreg generally occur to paper; hence, it urgently needs conservation and restoration. Therefore, herein, a new reinforcement method for the fragile double-sided printed paper cultural relics is proposed with cotton mesh and adhesive PVA217 as reinforcement materials. Using a computer measured and controlled folding endurance tester, a pendulum tensile strength tester, pH meter, pulp viscosimeter, and other instruments, the physical properties of newspaper samples before and after aging were evaluated. In addition, the mechanical properties, chromatic aberration and surface morphology of simulated samples before and after the cotton mesh reinforcement and Japanese washi paper reinforcement were assessed. The experimental results indicate that this new reinforcement method could effectively improve the physical strength, chromatic aberration and durability of the simulated samples. Widespread applications of this cotton mesh reinforcement method for the reinforcement and protection of the red revolutionary cultural relics such as double-sided printed newspaper and periodicals during the Republic of China era are foreseeable.

Purpose The purpose of this study is to reveal the usability of waste paper sludge on the production of composite materials and the printability of their surfaces were investigated. Design/methodology/approach First, composite plates were produced by using dried and milled waste sludge together with polyester resin and epoxy. Screen printing using water, solvent and UV-based inks were carried out. Findings It was determined that UV and solvent-based inks in both resin groups were permanently attached to the surface of composite plates produced using paper mill waste sludge, while it was found that the adhesion was not achieved sufficiently in cardboard factory waste sludge. Originality/value The unique aspect of this study is obtained the composite plates from paper mill and cardboard mill waste sludge and improved the printability of them.

Paper manufacturing on a global scale is a highly competitive market which requires to constantly improve the manufacturing process to be competitive. To decrease production cost paper manufactures, add filler material prior to sheet forming to replace costly wood fiber based raw material. This research project investigates the use of in-situ precipitated calcium carbonate produced in the presence of eucalyptus fiber material at a 41.0% filler level prior to beating. The in-situ filler containing eucalyptus fiber suspension was used on a 12’ (304mm) wide Laboratory Fourdrinier Paper Machine together with non-filler containing eucalyptus fiber material, and a commercial precipitated calcium carbonate filler material. The manufactured in-situ fiber suspension resulted in a higher ash retention compared to the addition of the powdered commercial PCC filler material. In addition to commercial filler material retention is improved at higher filler addition above 30%. The increased ash retention is linked to the increased micro fibrillation fiber material of the in-situ filler-fiber suspension forming neckless like particles on the fibers microfibrils. Mechanical paper properties showed an improvement for in-situ precipitated filler material compared to commercial filler material addition. Optical properties could be improved in comparison to the eucalyptus fiber without filler addition for in-situ precipitated filler material and a combination of in-situ and commercial filler material.

Tremendous attention has been paid on high efficiency, readily available and stability of electrocatalysts. Herein, we ingenious report a one-step reaction strategy synthesis of CoFe/CP grown on three-dimensional (3D) nanoarray carbon paper (CP) containing non-precious metals for oxygen evolution reaction (OER) with low-cost and unique hierarchical porous structure. This amorphous CoFe/CP hybrid exhibits commendable electrocatalytic performance in the OER process, requiring only overpotential of 278 mV to achieve 10 mAcm−2 in 1.0 M KOH solution and a lower Tafel slope of 49.12 mVdec-1. In addition, this sample shows a long-term durability even at 200 mAcm−2 without obvious decay, which attributes to peculiar multistage graded nano structure and the change of composition at the interface of CP. Therefore, the remarkable OER activity can provide a new strategy to construct potential candidates, which will replace the state-of-the-art precious metals for OER in the future.

Palliative radiation therapy (pRT) is an effective tool for people with incurable cancer, in the treatment of many cancer-related symptoms such as pain, bleeding and dyspnea. As utilization rates for palliative radiation therapy increase, the demands on the healthcare system continue to grow. Radiation Therapists with advanced knowledge, skills and judgements began demonstrating their ability to practice autonomously in 2004, with the development of the Clinical Specialist Radiation Therapist (CSRT) role. Since this time, CSRTs with a specific focus in pRT (pCSRT) have been increasing in both numbers as well as their positive effects on the cancer care system. Integrating a pCSRT into the existing pRT system has resulted in increased access to and quality of pRT being delivered to palliative cancer patients. The benefits of the addition of pCSRTs to the cancer care system include increasing system capacity and increasing quality of care. This white paper provides information related to the improvements that can be realized in a RT program related to the care and treatment of its palliative patients by adding a pCSRT to the interprofessional healthcare team and suggest it as one of many strategies that can be undertaken to make improvements to access and quality of care.

The rapid economic growth and environmental concerns have led to high demands on paper and paper-based products in terms of variety, quantity, quality, and specialty. Enhancement and functionalization with additives are constantly required. Moving away from traditional petroleum-based additives, researchers have attempted to use “green” nanoadditives by introducing renewable environmentally friendly nanocellulose. This article studies the functions of nanocellulose as bio-additives (enhancer, retention and filtration reagent, and coating aid) in paper and paper products, and overviews the research development of nanocellulose-based additives and their applications in the paper industry for both efficient production and paper functionalization. The review shows that (1) a variety of nanocellulose-based bioadditives have been reported for various applications in paper and paper-based products, while commercially viable developments are to be advanced; (2) nanocellulose was mostly formulated with other polymer and particles as additives to achieve their synergistic effects; (3) major interests have concentrated on the nanocellulose in the specialty papers as representing more value added products and in the efficient utilization of recycled fibers, which remains most attractive and promising for future development. This report shall provide most useful database information for researchers and industries for paper recycling and enhancement, and paper-based products innovation and application.

Neonatal and infantile cholestasis (NIC) can represent the onset of a surgically correctable disease and of a genetic or metabolic disorder worthy of medical treatment. Timely recognition of NIC and identification of the underlying etiology are paramount to improve outcomes. Upon invitation by the Italian National Institute of Health (ISS), an expert working grouped was formed to formulate evidence-based positions on current knowledge about the diagnosis of NIC. A systematic literature search was conducted to collect evidence about epidemiology, etiology, clinical aspects and accuracy of available diagnostic tests in NIC. Evidence was scored using the GRADE system. All recommendations were approved by a panel of experts upon agreement of at least 75% of the members. The final document was approved by all the panel components. This position document summarizes the collected statements and defines the best-evidence diagnostic approach to cholestasis in the first year of life.

Managing Liquidity has seldom been being as vital as it has during the Covid-19 era. The financial impact of Covid-19 has left many firms on the brink of liquidation. This paper explores the effect cash holdings has had on Profitability of the firm and how it compares with commercial paper between the pre-Covid-19 era and the Covid-19 era. This paper employs and compares the ordinary least square regression between these eras. I find that firms are less liquid during the Covid-19 period compared to the pre-covid period. More importantly, I find that Liquidity has been more critical to a firm's Profitability during Covid-19 era compared to pre-covid 19 periods. Furthermore, Cash holdings represent a significant chunk of Liquidity. However, these Cash holdings dropped by a little in the covid-19 era. Finally, I find that both commercial paper and cash holdings are used as complements. However, this result is weakly supported during the pre-covid period.

Poly ( p-phenylene benzoisoxazole; PBO) paper is a potential raw material for use in honeycomb sandwich composites in the aerospace industry, which are able to sustain high temperatures exceeding 300°C. This work presents a wet-forming method of making PBO paper, consisting of PBO chopped fibers. The paper was impregnated with phenolic resin to simulate honeycomb wall material. The structure and mechanical and dynamic mechanical properties of the raw and impregnated paper were characterized. The performance of PBO paper was tested against p-aramid paper. The comparative results showed the tensile strength of PBO raw paper was 2.17 kN/m, which was slightly worse than p-aramid raw paper: 2.66 kN/m. After impregnation, the tensile strength of the PBO paper was 13.93 kN/m due to the increase in the number of bonding points—better than p-aramid paper: 7.99 kN/m. The tearing resistance value for PBO raw paper versus p-aramid raw paper was 3252 mN against 845 mN. The morphology of the torn samples in the impregnated paper revealed higher levels of PBO fiber pullout than p-aramid fiber, therefore the tearing resistance value was 6000 mN for PBO impregnated paper, which was again superior to p-aramid impregnated paper: 675 mN. The PBO paper also showed higher storage modulus than p-aramid paper after impregnation. Experimental studies showed that PBO paper could be used in load-bearing structures and in honeycomb components where high resistance to deformation and thermal stability is necessary.

Purpose In flexible electronics applications, organic inks are mostly used for inkjet printing. Three-dimensional (3 D) printing technology has the advantages of low cost, high speed and good precision in modern electronic printing. The purpose of this study is to solve the high cost of traditional printing and the pollution emissions of organic ink. It is necessary to develop a water-based conductive ink that is easily degradable and can be 3 D printed. A nano-silver ink printed circuit pattern with high precision, high conductivity and good mechanical properties is a promising strategy. Design/methodology/approach The researched nano-silver conductive ink is mainly composed of silver nanoparticles and resin. The effect of adding methyl cellulose on the ink was also explored. A simple 3 D circuit pattern was printed on photographic paper. The line width, line length, line thickness and conductivity of the printed circuit were tested. The influence of sintering temperature and sintering time on pattern resistivity was studied. The relationship between circuit pattern bending performance and electrical conductivity is analyzed. Findings The experimental results show that the ink has the characteristics of low silver content and good environmental protection effect. The printing feasibility of 3 D printing circuit patterns on paper substrates was confirmed. The best printing temperature is 160°C–180°C, and the best sintering time is 30 min. The circuit pattern can be folded 120°, and the cycle is folded more than 60 times. The minimum resistivity of the circuit pattern is 6.07 µΩ·cm. Methyl cellulose can control the viscosity of the ink. The mechanical properties of the pattern have been improved. The printing method of 3 D printing can significantly reduce the sintering time and temperature of the conductive ink. These findings may provide innovation for the flexible electronics industry and pave the way for alternatives to cost-effective solutions. Originality/value In this study, direct ink writing technology was used to print circuit patterns on paper substrates. This process is simple and convenient and can control the thickness of the ink layer. The ink material is nonpolluting to the environment. Nano-silver ink has suitable viscosity and pH value. It can meet the requirements of pneumatic 3 D printers. The method has the characteristics of simple process, fast forming, low cost and high environmental friendliness.

The pulp and paper industry is highly energy-intensive. In mills that use chemical pulping, roughly half of the higher heating value of the cellulosic material used to manufacture the product typically is incinerated to generate steam and electricity that is needed to run the processes. Additional energy, much of it non-renewable, needs to be purchased. This review considers publications describing steps that pulp and paper facilities can take to operate more efficiently. Savings can be achieved, for instance, by minimizing unnecessary losses in exergy, which can be defined as the energy content relative to a standard ambient condition. Throughout the long series of unit operations comprising the conversion of wood material to sheets of paper, there are large opportunities to more closely approach a hypothetical ideal performance by following established best-practices.

Aβ42 is one of the most extensively studied blood and Cerebrospinal fluid (CSF) biomarkers for the diagnosis of symptomatic and prodromal Alzheimer’s disease (AD). Because of the heterogeneity and transient nature of Aβ42 oligomers (Aβ42Os), the development of technologies for dynamically detecting changes in the blood or CSF levels of Aβ42 monomers (Aβ42Ms) and Aβ42Os is essential for the accurate diagnosis of AD. The currently commonly used Aβ42 ELISA test kits usually mis-detected the elevated Aβ42Os, leading to incomplete analysis and underestimation of soluble Aβ42, resulting in a comprised performance in AD diagnosis. Herein, we developed a dual-target lateral flow immunoassay (dLFI) using anti-Aβ42 monoclonal antibodies 1F12 and 2C6 for the rapid and point-of-care detection of Aβ42Ms and Aβ42Os in blood samples within 30 min for AD diagnosis. By naked eye observation, the visual detection limit of Aβ42Ms or/and Aβ42Os in dLFI was 154 pg/mL. The test results for dLFI were similar to those observed in the enzyme-linked immunosorbent assay (ELISA). Therefore, this paper-based dLFI provides a practical and rapid method for the on-site detection of two biomarkers in blood or CSF samples without the need for additional expertise or equipment. Graphical Abstract

Paper-based fluorescence devices, with smartphone aids, bring considerable operation convenience for tetracycline (TC) sensing. Nevertheless, they must meet the challenge in real determination against complicated backgrounds. Considering that, we present a programmable-printing paper-based device and then apply it to TC determination for various natural samples. MoS2 NPs and Gmp/Eu-Cit are synthetized as composite probes. A static quenching process is found with MoS2 NP fluorescence at 430 nm, while significant magnification of Gmp/Eu-Cit emission is obtained at 617 nm, establishing a valuable ratiometric indicator. Remarkably, two-stage programmable printing maximizes the proposed sensing capability. A transitive device, containing a gradually changing amount of a certain probe, is prepared to sense TC. With a homemade smartphone application and 3D-printed measurement chamber, the corresponding signals are examined to explore optimal setups. These setups are automatically processed to prepare the final-version device, not requiring manual operations. Benefitting from this interesting feature, the proposed device gains many rewards in performances. It effectively senses TC in a wide range from 12.7 nM to 80 μM and simultaneously provides naked eye-legible signals and smartphone-based readouts with confident selectivity and stability. This device is consequently applied for various samples of soil, river water, milk, and serum and meets well with HPLC-MS and recovery tests.

Parenteral and enteral nutrition support are key components of care for various medical and physiological conditions in infants, children, and adults. Nutrition support practices have advanced over time, driven by the goals of safe and sufficient delivery of needed nutrients and improved patient outcomes. These advances have been, and continue to be, dependent on research and development studies. Such studies address aspects of enteral and parenteral nutrition support: formulations, delivery devices, health outcomes, cost-effectiveness, and related metabolism. The studies are supported by public funding from the government and by private funding from foundations and from the nutrition support industry. To build public trust in nutrition support research findings, it is important to underscore ethical research conduct and reporting of results for all studies, including those with industry sponsors. In 2019, American Society for Parenteral and Enteral Nutrition's (ASPEN's) Board of Directors established a task force to ensure integrity in nutrition support research that is done as collaborative partnerships between the public (government and individuals) and private groups (foundations, academia, and industry). In this ASPEN Position Paper, the Task Force presents principles of ethical research to guide administrators, researchers, and funders. The Task Force identifies ways to curtail bias and to minimize actual or perceived conflict of interests, as related to funding sources and research conduct. Notably, this paper includes a Position Statement to describe the Task Force's guidance on Public-Private Partnerships for research and funding. This paper has been approved by the ASPEN Board of Directors.

The Government of Ireland has published its plan to reorder the infrastructure it uses to accommodate and support migrants seeking International Protection (IP) in Ireland. This policy document - entitled The White Paper to End Direct Provision and Establish a New International Support Service - was published on 26th February, 2021. The White Paper proposes to replace Ireland's current but discredited system with a new IP accommodation and support process – to be entitled Ireland's International Protection Support Service. This new system is intended to “treat all applicants to the process with dignity and respect” (Government of Ireland, 2021: 7). Dissonances exist, however. The discursive framing of the IPSS and the spatialities inherent in the proposals suggest a potential rearticulation of state control rather that a diminution of same. I turn to the work of scholars inspired by Giorgio Agamben to help situate the spatialities of this shift, and suggest that the current ‘white paper’ should simply be seen as a mechanism deployed the Government of Ireland to ensure that its bio-political command and control processes can migrate from the spatially-defined set of control environments currently in effect to a diffuse construction of a spatially networked series of deterritorialised indistinctions.

Since the end of 2019, the whole world has been seized by the COVID-19 pandemic caused by the SARS-CoV2 virus. To date, the infection has led to more than 4 million deaths worldwide, and to more than 140 thousand deaths in Russia. COVID-19 (abbreviation for COronaVIrus Disease 2019) is a potentially severe acute respiratory infection caused by the SARS-CoV-2 coronavirus (2019-nCoV). Vaccination against COVID-19 plays a key role in stopping the pandemic. According to existing experience in infections prevention, mass vaccination will reduce the virus’s expansion and the risk of vaccine-resistant strains’ development. In the context of the COVID-19 the question of the feasibility and safety of vaccination of patients with Primary Immunodeficiency and Hereditary Angioedema arises. The Russian Association of Allergists and Clinical Immunologists and the National Association of Experts in Primary Immunodeficiencies have developed and approved a position paper on vaccination of patients with Primary Immunodeficiency and Hereditary Angioedema against COVID-19. This position paper provides answers to key questions regarding the vaccination of patients with these diseases.

Objective The aims of the study were: (1) to clarify the definitions of “migrant” used in occupational health research; (2) to summarize migrant workers’ industry sectors, occupations and employment conditions; (3) to identify the occupational health and safety services available to migrant workers; (4) to summarize work-related health problems found among migrant workers; (5) to identify the methodological challenges to research into occupational health of migrant workers; and (6) to recommend improvements in migrant occupational health research. Methods This position paper was prepared by researchers from several European countries and Australia, working within the EU COST Action OMEGA-NET. The paper drew on two recent systematic reviews on the occupational health of international migrant workers and other literature, and also identified uncertainties and gaps in the research literature. Migrants may, for example, be temporary or permanent, moving for specific jobs migrants or other reasons. Their ethnicity and language capabilities will affect their work opportunities. Results The occupational health literature seldom adequately identifies the heterogeneity or characteristics of the migrant group being studied. Migrants tend to work in more physically and mentally demanding environments with higher exposures than native workers. Migrants tend to have an increased risk of physical and mental ill health, but less access to health care services. This has been demonstrated recently by high rates of COVID-19 and less access to health care. There have been a number of cross-sectional studies of migrant health but few long-term cohort studies were identified. Other study designs, such as registry-based studies, surveys and qualitative studies may complement cross-sectional studies. Mixed-methodology studies would be valuable in research on migrants’ occupational health. Language and lack of trust are barriers to migrant research participation. Conclusion Targeted research, especially longitudinal, identifying how these economically important but often-vulnerable workers can be best assisted is needed. Researchers should identify the characteristics of the migrant workers that they are studying including visa/migration circumstances (temporary, permanent, undocumented), racial and ethnic characteristics, existing skills and language abilities.

Recent decades have witnessed increasing interest in the concept of the circular economy within both the business world and political circles. The circular economy spans the entire life cycle of products from product design through production, marketing, and consumption, to waste management, recycling, and re-use, and enthusiasm for putting the concept into practice has been identified across different sectors of the economy. This exploratory case study reviews how some of the leading companies in the paper and retail industries, have publicly addressed the circular economy. The case study outlines the nature of the circular economy, provides a cameo literature review of published work on the circular economy, describes the approach adopted for the case study, reports the findings of the review of how the leading companies in the paper and retail industries have addressed the circular economy, and discusses some wider issues. Keywords: circular economy, case study, paper industry, retail industry, greenwash, economic growth

Introduction. The Shchuchiy Bay is located in the western part of the skerry area of Lake Ladoga near the town of Priozersk. For almost 20 years, the bay has experienced an anthropogenic impact from the ingress of untreated wastewater from the Priozersk Pulp and Paper Mill (PPM). Systematic microbiological studies of the Shchuchiy Bay ecosystem were started in the middle of the 1970s by the Institute of Limnology of the Russian Academy of Sciences and continued after the PPM closure in 1986. Materials and methods. The ecosystem of the bay was studied in detail during the growing season of 2013–2014; periodic studies were carried out in 2015–2018. Retrospective data were also used for the analysis. Water samples were taken at four stations from the surface horizon. The following microbiological indicators were determined: the abundance of bacterioplankton and the percentages of various morphological types of bacterial cells. Results and discussion. A comparison of the quantitative level of development of the bacterial community in the bay in different periods showed a gradual decrease in the abundance of bacterioplankton as the anthropogenic impact weakened after the closure of the Priozersky PPM from 12.40 million cells ml–1 in 1987 to an average value of 2.62±1.03 million cells ml–1 in 2013–2018. A positive correlation was found between the concentration of bacteria and water temperature. The percentage of rod-shaped microorganisms in the water of the bay also decreased as the anthropogenic impact weakened from 73.4 % in 1987 to 53.1±7.6 % in 2013–2018, which indicated an improvement in water quality. Conclusion. A stable decrease in the abundance of bacteria from the level characteristic of highly polluted and eutrophic water bodies to the level characteristic of mesotrophic and mesotrophic-eutrophic water bodies is a reliable criterion for the restoration of the ecosystem of the Shchuchiy Bay to the state characteristic of similar bays of Lake Ladoga.

The performance of modified anaerobic hybrid baffled (MAHB) bioreactor treating recycled paper mill effluent (RPME) was investigated at various organic loading rates (OLR) of 1, 2, 3 and 4 g COD/ L.day. The bioreactor was operated continuously at constant hydraulic retention time (HRT) of a day without effluent recycled and chemicals adjustment/addition. Throughout 70 days of operation, a maximum removal efficiency up to 97% of chemical oxygen demand (COD) and 98% of volatile fatty acid, biogas production of 12.51 L/day equivalent to methane (CH4) yield of 0.108L CH4/ g COD and a stable pH system between 6.6 to 7.2 were achieved. Additionally, alkalinity of the bioreactor system shows a stable profile that indicates the whole system was well buffered with a quit high degradation of volatile solid (VS) up to 18%. These results indicated that MAHB bioreactor has been successfully treated RPME at various OLR.

In the present approach, a Cr2O3-TiO2-modified, portable, and biomimetic nanosensor was designed to meet the requirement of a robust and colorimetric sensing of hydrogen peroxide. Cr2O3-TiO2 nanocomposites prepared via the hydrothermal method were fabricated as a transducer surface on the filter paper using the sol-gel matrix. The color on the filter paper sensor changed from green to blue upon the addition of hydrogen peroxide in the presence of TMB. This change in the color intensity was linear with the concentration of H2O2. RGB software was used as a color analyzing model to evaluate the optical signals. This paper-based colorimetric platform provided us with an improved analytical figure of merit with a linear range of 0.005-100 μM with 0.003 μM limit of detection. The real sample analysis and excellent anti-interference potential results proved the good analytical performance of the proposed design, providing a more promising tool for colorimetric H2O2 detection. Introducing Cr2O3-TiO2 nanocomposite-based paper sensors, being a novel method for optical and colorimetric detection, can pave the way for the development of other sensing devices for the detection of different analytes.

Although crucial in improving health outcomes in the preterm infants, parenteral nutrition (PN) is not without risk, especially if handled improperly. A growing body of evidence suggests that components of PN admixtures, including lipid injectable emulsions (ILEs), are susceptible to degradation, including oxidation when exposed to light (ie, photo-oxidation), resulting in the production of reactive oxygen species. Infants, especially those born preterm, are considered more susceptible to consequences of oxidative stress than children and adults. Oxidative stress is associated with bronchopulmonary dysplasia, retinopathy of prematurity, necrotizing enterocolitis, and intestinal failure-associated liver disease. The American Society for Parenteral and Enteral Nutrition (ASPEN) assembled a working group to provide recommendations on clinical practice surrounding photoprotection of PN.This Position Paper reviews the scientific literature on the formation of quantifiable peroxides and other degradation products when PN admixtures and ILEs are exposed to light and reports adverse clinical outcomes in premature infants exposed to PN. Recommendations for photoprotection of PN admixtures and ILEs are provided, as well as the challenges in achieving complete photoprotection with the equipment, supplies, and materials currently available in the US. ASPEN and the authors understand that the full implementation of complete photoprotection may not currently be feasible given current product availability; recommendations provided in this paper serve to represent the goal to which to strive as well as to highlight the importance of product availability to achieve these practices. This paper has been approved by the ASPEN Board of Directors.

The study attempted to assess the water quality around paper mill effluents discharge areas. Several physicochemical parameters and the Canadian Council of Ministers of the Environment (CCME) Water Quality Index (WQI) were considered to determine the pollution level of surface and groundwater in the selected paper mills areas located in Saidpur, Gobindaganj, and Dupchanchia Upazilas of Bangladesh. Physicochemical characterization of the surface water around the paper mills areas showed that the concentration of EC, TSS, BOD5, COD, phenols, NO3−-N, and K+were exceeded the surface water standard, whereas the DO level ranged from 1.63 to 3.5 were found below the Environmental Conservation Rules (ECR), 1997 standard. Besides, the BOD, COD, and Mn ion concentrations of groundwater exceeded the drinking water standard. In most sampling sites, the WQI of the surface water showed ‘marginal’ category, and the groundwater quality showed 'fair' category. The study observed that the toxic effluents discharged from the paper mills caused harm to the aquatic ecosystem.

With the development of printed electronics technology, the demand for printed conductive inks had also put forward higher standards. The shortcomings of traditional printed circuit boards, such as complex technology, consumables, and pollution, had also been resolved with the development of 3D printing technology. In this paper, low-content silver nanoparticles were blended with graphene alcohol slurry and dissolved in a non-polluting solvent such as absolute ethanol. The synergistic effect of the composite of the hexagonal structure of the graphene sheet and the silver nanoparticles improved the ink’s performance of electrical conductivity, adding water-based polyurethane/acrylic resin system to improve the adhesion between ink and paper. The conductive ink can be used to 3D print circuit circuits on paper. After drying, the resistance was measured. After the battery, diode, and switch were connected, a circuit diagram was made. After pressing the diode emits was lighted. This work is expected to be applied to flexible circuit boards to provide basic research.

The spread of Coronavirus disease 2019 (COVID-19) is caused by severe acute respiratory syndrome-coronavirus 2 (SARS-CoV-2), resulting in a global pandemic with around four million deaths. Although there are a variety of nucleic acid-based tests for detecting SARS-CoV-2, these methods have a relatively high cost and require expensive supporting equipment. To overcome these limitations and improve the efficiency of SARS-CoV-2 diagnosis, we developed a microfluidic platform that collected serum by a pulling-force spinning top and paper-based microfluidic enzyme-linked immunosorbent assay (ELISA) for quantitative IgA/IgM/IgG measurements in an instrument-free way. We further validated the paper-based microfluidic ELISA analysis of SARS-CoV-2 receptor-binding domain (RBD)-specific IgA/IgM/IgG antibodies from human blood samples as a good measurement with higher sensitivity compared with traditional IgM/IgG detection (99.7% vs 95.6%) for early illness onset patients. In conclusion, we provide an alternative solution for the diagnosis of SARS-CoV-2 in a portable manner by this smart integration of pulling-force spinning top and paper-based microfluidic immunoassay.

The pulp and paper industry is primarily dependent on fibrous wood for pulp and paper production. However, this over-dependence on fibrous wood poses serious environmental challenges such as the diminishing of the fibrous wood stocks, deforestation, emission of greenhouse gases, and global warming. Therefore, to mitigate these environmental challenges associated with its utilization for paper and pulp production, other sustainable raw material sources can also be considered for the production of paper and pulp. There are enormous benefits associated with the utilization of non-wood fibres as an alternative and sustainable raw materials source for the production of paper and pulp. These benefits have in the recent past prompted millers in China, India, Brazil, and the USA to consider the utilization of non-wood fibres in paper and pulp production. In Kenya, the pulp and paper industry is very much dependent on fibrous wood for production and the industry is yet to fully embrace the utilization of nonwood fibres for paper and pulp production. Further, the dependence on fibrous wood has contributed significantly to the decline of paper pulp and paper production, deforestation, and rise in paper importations due to insufficient raw material supplies. The importation of paper and pulp products has further led to the collapse of the paper industry in Kenya. The sector stands a chance of revival and vibrancy through the utilization of the abundant agricultural residues and feedstocks lying in the agricultural fields across the country. Similar experiences elsewhere have proved that the abundance of agricultural waste can be utilized for the production of paper and pulp due to their excellent fibre content for specialty papers, and easy pulpability. The agricultural residues are therefore considered a quintessential alternative and sustainable source of raw materials for the pulp and paper industry. Moreover, their utilization will mitigate environmental impacts such as deforestation, climate change, and pollution .

With the increased awareness of reusing solid wastes for higher sustainability and the concern of water pollution associated with phosphorus over-emission, there are strong interests in developing solid waste based adsorbents for purifying phosphorus-containing wastewater. As a rich calcium resource, paper mill sludge (i.e., a major solid waste from pulping industry) can be used as phosphorus removal adsorbent after calcination. Thus, in this work, a simple and clean thermally treating route has been proposed for preparing calcium-containing biochar from paper mill sludge. The effect of the physicochemical properties of paper mill sludge and its carbonization condition on phosphorus adsorption has been analyzed. Moreover, the influence of some key adsorption parameters, e.g., biochar dosage, initial pH of solution, co-existing anions, initial phosphorus concentration and contact time has also been investigated. The results showed that the phosphorus adsorption data could be fitted well with pseudo-second-order kinetic and Langmuir isothermal models. The calculated maximum adsorption capacity of the as-prepared optimal calcium-containing biochar could reach to 68.49 mg·g−1 at 25 °C. Combined with the characterization results, it can be reasonably inferred that the adsorption process was chemisorption-dominated. Lastly, the application of this spent adsorbent in agriculture field has also been discussed. In brief, this work provided a feasible strategy for converting paper mill solid waste to an environmental functional material (i.e., calcium-rich biochar) for remediation of eutrophic water.

The paper presents a research on the disposal of the toxic waste of pulp and paper mill (sludge-lignin with the empirical formula CH1.51N0.05S0.03Cl0.01O0.54through its oxidation in supercritical water-oxygen fluid, including the case of using methane as a co-fuel. The experiments were carried out with a flow reactor of original design at a pressure of 25 MPa, temperature gradient along the vertical axis (from top to bottom: 390–600°C), and variation in the flow rate of the sludge-lignin (with the addition of NaOH, 1.6 wt %), oxygen, and methane. The experiments yielded data on the content of phenols in the water and the composition of the gaseous products collected at the outlet of the reactor versus the oxygen excess ratio. From these data, as well as the time dependences of the reactor wall temperature and the power of the ohmic heaters, it follows that using distributed supply of methane to compensate for the energy for heating of the reagents is preferable as compared with local inlet of methane to the upper part of the reactor. It has been shown that the addition of methane makes it possible to reduce the oxygen excess required for complete oxidation of the organic components of sludge-lignin.

Nitrogen-fixing bacteria (NFB) can reduce nitrogen at ambient pressure and temperature. In this study, we treated effluent from a paper mill in sequencing batch reactors (SBRs) and monitored the abundance and activity of NFB with a view to producing a sludge that could work as a biofertilizer. Four reactors were inoculated with activated sludge enriched with NFB and fed with a high C/N waste (100:0.5) from a paper mill. Though the reactors were able to reduce the organic load of the wastewater by up to 89%, they did not have any nitrogen-fixing activity and showed a decrease in the putative number of NFB (quantified with qPCR). The most abundant species in the reactors treating high C/N paper mill wastewater was identified by Illumina MiSeq 16S rRNA gene amplicon sequencing as Methyloversatilis sp. (relative abundance of 4.4%). Nitrogen fixation was observed when the C/N ratio was increased by adding sucrose. We suspect that real-world biological nitrogen fixation (BNF) will only occur where there is a C/N ratio ≤100:0.07. Consequently, operators should actively avoid adding or allowing nitrogen in the waste streams if they wish to valorize their sludge and reduce running costs. PRACTITIONER POINTS: Efficient biological wastewater treatment of low nitrogen paper mill effluent was achieved without nutrient supplementation. The sludge was still capable of fixing nitrogen although this process was not observed in the wastewater treatment system. This high C/N wastewater treatment technology could be used with effluents from cassava flour, olive oil, wine and dairy industries.

Surface characteristics of printing substrates are of the utmost importance to all types of paper that interact with ink. During all types of printing processes, the behaviour of the liquid phase (ink or dye) on the paper is directly defined by the paper cellulose-based surface. The printed ink spreads and penetrates more into paper fibres when the paper surface is rougher and more permeable. Contact angle measurements by sessile drop method are considered the most appropriate for determining the paper sheet surface energy. Paper as hydrophilic material has a high absorption rate resulting in a low contact angle. The objective of this study was to evaluate the surface free energy of laboratory-made papers containing straw pulp obtained from residues after the harvest of the most cultivated cereals in Croatia (wheat, barley and triticale). The obtained surface free energy results are promising for straw pulp usage in the manufacture of printing paper.

This study optimizes a novel surfactant-assisted green liquor dregs (GLD) pretreatment of paper mill sludge (PMS), both of which are wastes from the kraft pulping industry, using a combined Response Surface Methodology (RSM) design. Optimized conditions give a maximal reducing sugar release of 16.38 g/L. A substantial reduction in heavy metals aluminum, chromium, cobalt, arsenic, lead, and copper after pretreatment illustrates the enhancement of substrate digestibility by reducing toxic elements. Separate hydrolysis and fermentation (SHF) and simultaneous saccharification and fermentation (SSF) for hydrogen production are assessed. SSF produced a hydrogen yield of 3.72 mL/g, displaying a 36.26% increase from pretreated PMS compared to SHF. These findings provide insights into possible methods of reducing process duration, energy input, and costs incurred with waste disposal within the paper industry. Furthermore, improved hydrogen yield using an SSF process demonstrates the potential beneficiation of pulp and paper GLD and PMS wastes.