Search

The question of the expediency of increasing the energy efficiency of a large chemical and oil refining industry by using process heat carriers and raw materials as heaters of vapor compression heat pumps based on systems for recuperating heat process losses is considered. A feature of the energy system under consideration is the provision of the main circuit of the heat pump and its drive from a common source of thermal energy. The influence of the temperature parameters of the consumer of highpotential thermal energy, the source of low-potential thermal energy and the energy efficiency of the main functional elements of the energy system under consideration on the ratio of the amount of generated thermal energy supplied to the consumer to the amount of thermal energy losses used is analyzed. In addition, an assessment is made of the influence of the listed factors on the redistribution of low-potential thermal energy flows between the main circuit of the heat pump and its drive. The presented results reflect the fundamental possibility of increasing the temperature level of process heat carriers and raw materials without significant costs for additional external energy sources. The efficiency of reuse of heat losses in a closed technological cycle depends on the temperature conditions of the consumer and the source of thermal energy in the heat pump cycle, on the connection scheme of the thermal energy source and on the energy efficiency of the equipment used.

The question of the feasibility of increasing the energy efficiency of large chemical and oil refining industries by replacing furnace heaters of process heat carriers and raw materials with vapor compression heat pumps is considered. An analysis of the relationship between the technical configuration of vaporcompression heat pumps, the operating parameters of their operation (determining the value of the energy conversion coefficient) and the ratio of the cost of various energy carriers is carried out. The presented results of a comparative analysis of the energy efficiency of various options for replacing a furnace with a vapor compression heat pump reflect the decisive influence of the technical level and design configuration of a vapor compression heat pump on the choice of the preferred upgrade option. However, a significant difference in commercial energy prices significantly changes the preferred ranking of these options.

The biotechnological exploitation of microorganisms enables the use of metabolism for the production of economically valuable substances, such as drugs or food. It is, thus, unsurprising that the investigation of microbial metabolism and its regulation has been an active research field for many decades. As a result, several theories and techniques were developed that allow for the prediction of metabolic fluxes and yields as biotechnologically relevant output parameters. One important approach is to derive macrochemical equations that describe the overall metabolic conversion of an organism and basically treat microbial metabolism as a black box. The opposite approach is to include all known metabolic reactions of an organism to assemble a genome-scale metabolic model. Interestingly, both approaches are rather successful at characterizing and predicting the expected product yield. Over the years, macrochemical equations especially have been extensively characterized in terms of their thermodynamic properties. However, a common challenge when characterizing microbial metabolism by a single equation is to split this equation into two, describing the two modes of metabolism, anabolism and catabolism. Here, we present strategies to systematically identify separate equations for anabolism and catabolism. Based on metabolic models, we systematically identify all theoretically possible catabolic routes and determine their thermodynamic efficiency. We then show how anabolic routes can be derived, and we use these to approximate biomass yield. Finally, we challenge the view of metabolism as a linear energy converter, in which the free energy gradient of catabolism drives the anabolic reactions.

This paper is devoted to the determination of the value of the maximum specific power of capacitive electrostatic micromotors based on nanometer working gaps. The motors under consideration were developed earlier. They have the following structure: a metal—thin crystalline ferroelectric layer with a high dielectric constant—a nanometer working gap—a movable electrode. The mechanism limiting the magnitude of the maximum field in the gap have also been determined in previous works. The mechanism is the stripping of atoms from the surface of the movable electrode under the action of electrostatic forces. It was shown that the maximum energy density in the working gap can be as high as 1.6 × 109 J/m3. In the presented paper, a maximum frequency of electromechanical energy conversion as high as 10 MHz is estimated for these motors, with a maximum specific power of 5 × 108 W/kg. The application of the proposed motors for micromachines is discussed.

The supply of energy with the correct parameters to electrical appliances is possible with the use of energy converters. When a direct current is required, rectifier bridges are needed. These can be made using rectifier diodes. The problem of excessive junction temperatures in power diodes, which are used to build rectifier bridges and power converters, was recognized. For this reason, research work was carried out to create a model of a rectifier diode placed on a heat sink and to analyze the heat dissipation from the junction of this diode under forced convection conditions. The results obtained from the simulation work were compared with the results of thermographic temperature measurements. The boundary conditions chosen for the simulation work are presented. A method is also presented that determined the convection coefficient under forced convection conditions. The difference between the simulation results and the results of the thermographic measurements was found to be 0.1 °C, depending on the power dissipated at the junction and the air velocity around the diode.

Vortex-induced oscillations offer a potential means to harness hydrokinetic energy even at low current speeds. In this study, we consider a novel converter where a cylinder undergoes angular oscillations with respect to a pivot point, in contrast to most previous configurations, where the cylinder undergoes flow-induced oscillations transversely to the incident free stream. We formulate a theoretical model to deal with the coupling of the hydrodynamics and the structural dynamics, and we numerically solve the resulting nonlinear equation of cylinder motion in order to assess the performance of the energy converter. The hydrodynamical model utilizes a novel approach where the fluid forces acting on the oscillating cylinder are split into components acting along and normal to the instantaneous relative velocity between the moving cylinder and the free stream. Contour plots illustrate the effects of the main design parameters (in dimensionless form) on the angular response of the cylinder and the energy efficiency of the converter. Peak efficiencies of approximately 20% can be attained by optimal selection of the main design parameters. Guidelines on the sizing of actual converters are discussed.

The analysis of electromechanical energy converters based on metal-thin film ferroelectric (with a large specific capacitance)-nanogap-moving electrode structures was performed. It was shown that the density of the energy being converted and its absolute value increase with the decreasing gap value between the surfaces of the ferroelectric and the metallic moving electrode up to nanometer values. The effects limiting the growth of this energy were established, and the limiting value of the energy density transformed in the nanogap of these structures was determined to be about 1.6 × 1010 J/m3, which is 4 orders of magnitude higher than the energy density in inductive converters. The experimental verification of this model based on the data for micromotors fabricated on these structures is given.

OBREC is the acronym that stands for Overtopping Breakwater for Energy Conversion. It is a multifunctional device aimed to produce energy from the waves, while keeping the harbour area protected from flooding. In this paper, the inclusions of a berm to reduce wave reflection, the shape of the sloping plate to maximise wave overtopping and the reservoir width and the crown wall shape to maximise wave energy capture while keeping the harbour safety were analysed to optimize the hydraulic and structural performances of the device. Several configurations were numerically investigated by means of a 2DV RANS-VOF code to extend the results already obtained during previous experimental campaigns. The wave reflection coefficient, the average wave overtopping flows and the wave loadings along the structure are computed, compared with existing formulae and discussed with reference to the OBREC prototype installed in the Port of Naples.

This study is the result of ongoing research for a European Union 7th Framework Program Project regarding energy converters for very low heads, and aims to analyze optimization of new cost-effective hydraulic turbine designs for possible implementation in water supply systems (WSSs) or in other pressurized water pipe infrastructures, such as irrigation, wastewater, or drainage systems. A new methodology is presented based on a theoretical, technical and economic analysis. Viability studies focused on small power values for different pipe systems were investigated. Detailed analyses of alternative typical volumetric energy converters were conducted on the basis of mathematical and physical fundamentals as well as computational fluid dynamics (CFD) associated with the interaction between the flow conditions and the system operation. Important constraints (e.g., size, stability, efficiency, and continuous steady flow conditions) can be identified and a search for alternative rotary volumetric converters is being conducted. As promising cost-effective solutions for the coming years, adapted rotor-dynamic turbomachines and non-conventional axial propeller devices were analyzed based on the basic principles of pumps operating as turbines, as well as through an extensive comparison between simulations and experimental tests.