Search

The study explores the application of tea leaf-extracted tannin as a bio-mordant and thyme extract as a natural dye on cationized silk-cotton blend fabric to enhance colour fastness and absorption. The colour strength and depth (shown as DL, Da, and Db values) on silk-cotton blend fabric were investigated in the CIE lab test. The results showed that temperature, shade percentage, and mordanting had a substantial impact on the dyeing process efficacy at DL = 30.61, Da = 11.49 and Db = 12.77. When the temperature was raised to 90 °C and the dye content was increased to 120%, the dyed sample's colour fastness (as measured by wash, rubbing, and perspiration) significantly improved, acquiring a grade of 4 to 5, which indicates good to excellent. There was a slight change in wet rubbing fastness from grade 3 to grade 4, indicating good to fair. The K/S values of the silk and cotton fibres, which ranged from 8.89 to 7.94 on average, respectively, demonstrated that the processes of bio-mordanting and cationization enhanced the absorption of dye. Tensile strength and extension increased in the weft direction to 22.19 N force and 5.21% extension at break, while the warp direction showed a fall to 6.63 N force and a rise in extension of 0.72%. FTIR spectroscopy confirmed the presence of Amino (N-H) bonds, Carbohydrate bonds (CH), Tannins, and Terpenoid phytochemicals of thyme in the dyed sample. The study highlights the potential of thyme extract as a natural dye and its benefits in improving the dyeing properties of silk-cotton blend fabric.

The dyeing characteristics of hardwood kraft lignin (KL) were investigated on cotton fabrics, assessing its potential as a sustainable and environmentally friendly dye. Dyeability was evaluated by varying the KL concentrations, temperature, and time. An aqueous solution of Na2CO3 (1.0%) as the dye bath and a fabric-to-liquor ratio of 1:50 were used. Cationizing effects were studied using (3-chloro-2-hydroxypropyl) trimethylammonium chloride (CHPTAC), and the mordanting effects of various mordants were also evaluated. Post-mordanting was performed with FeSO4, FeCl2, Fe-lactate (Fe-lac), MgSO4, CuCl2, CuSO4, and Al2(SO4)3. A mordant concentration of 1 mM o.w.f. (0.5 mM for Al2(SO4)3), with a liquor ratio of 1:30, at 60 °C for 30 min were employed. Suitable dyeing conditions were 2.0% o.w.b., 90 °C, and 90 min, resulting in a brownish color of the cotton fabric. The fabrics exhibited a range of light brown to light grayish brown colors and showed lighter colors than the untreated fabrics when mordanted with MgSO4 and Al2(SO4)3. The color difference (ΔE) between cationized and uncationized cotton fabrics was 3.48. From the colorfastness assessment, KL-dyed cotton fabric showed good rubbing and washing fastness for staining, but poor light and washing fastness for fading.

The dyeing characteristics of hardwood kraft lignin (KL) were investigated on cotton fabrics, assessing its potential as a sustainable and environmentally friendly dye. Dyeability was evaluated by varying the KL concentrations, temperature, and time. An aqueous solution of Na2CO3 (1.0%) as the dye bath and a fabric-to-liquor ratio of 1:50 were used. Cationizing effects were studied using (3-chloro-2-hydroxypropyl) trimethylammonium chloride (CHPTAC), and the mordanting effects of various mordants were also evaluated. Post-mordanting was performed with FeSO4, FeCl2, Fe-lactate (Fe-lac), MgSO4, CuCl2, CuSO4, and Al2(SO4)3. A mordant concentration of 1 mM o.w.f. (0.5 mM for Al2(SO4)3), with a liquor ratio of 1:30, at 60 °C for 30 min were employed. Suitable dyeing conditions were 2.0% o.w.b., 90 °C, and 90 min, resulting in a brownish color of the cotton fabric. The fabrics exhibited a range of light brown to light grayish brown colors and showed lighter colors than the untreated fabrics when mordanted with MgSO4 and Al2(SO4)3. The color difference (ΔE) between cationized and uncationized cotton fabrics was 3.48. From the colorfastness assessment, KL-dyed cotton fabric showed good rubbing and washing fastness for staining, but poor light and washing fastness for fading.

Pectin cellulose grafted with glycidyltrimethylammoniochloride (GTMAC) was successfully obtained following the processes of depectinfibrillation and cellulose cationization using ordinary Shatian pomelo peel produced in Yongzhou, Hunan, as the raw material. This is the first report on a new type of functionalized sodium alginate-immobilized material prepared from the fibers of pomelo peel. The material was prepared by combining modified pomelo peel cellulose and sodium alginate following the processes of physical and chemical double cross-linking. The prepared material was used to embed the target bacteria to achieve the biodegradation of p-aniline. The concentration of CaCl2 was adjusted when the alginate gelled, and the alginate to yuzu peel cellulose ratio was tuned. The immobilized material-embedded bacteria help achieve the best degradation effect. Bacteria are embedded during the process of the degradation of aniline wastewater, and the functionalization of the cellulose/sodium alginate-immobilized material results in unique surface structure performance. The performance of the prepared system is better than that of the single sodium alginate-based material characterized by a large surface area and good mechanical properties. The degradation efficiency of the system is improved significantly for the cellulose materials, and the prepared materials can potentially find applications in the field of bacteria-fixed technology. HIGHLIGHTS Pomelo peel fiber was extracted for the first time and used in the preparation of immobilized material.; By combining with sodium alginate, the specific surface area of the fixed material can be increased by the pomelo peel fiber with a spiral tube shape and rough surface.; The cationic-modified pomelo peel fiber can improve the mechanical properties and stability of the immobilized material by ionic bonding.;

The textile industry has been exploring sustainable chemicals and natural alternatives to replace harmful and carcinogenic substances used in different stages of textile production for dyeing textiles. Natural dyes are gaining popularity, as they are environmentally friendly and less harmful. Betacyanin, a type of pigment obtained from red pitahaya, commonly known as red dragon fruit (Hylocereus polyrhizus), has peels that are available as agricultural waste and can be used to meet the demand for natural dye production. This study aimed to explore and utilize dragon fruit’s peel as a natural colorant for dyeing 100% cotton knit fabric (scoured and bleached single jersey plain knit) of 170 g/m2, which could transform a low-value material into a valuable product. However, cotton’s phenolic nature and oxidation process result in negative charges on its surface, making natural dyeing challenging. Cationization with cationic agents (ForCat NCH, a mixture of cationic polyamine and 1,3,dichlori-2-propanol) and mordanting (potassium alum or potassium aluminum sulfate) were carried to improve dye exhaustion and enhance colorfastness properties. Spectrophotometer 800 was used to measure color strength (K/S), and several fastness tests, including wash, perspiration, and rubbing were conducted to assess the final product’s performance. The process parameters, such as temperatures, times, pH levels, and dye concentrations were varied to understand better the optimum conditions.

The study investigated the effect of modifying rapeseed husks with ammonia and epichlorohydrin on their sorption capacity against anionic reactive dyes: Reactive Black 5 (RB5) and Reactive Yellow 84 (RY84). Its scope included sorbents characterization (FTIR, pHPZC), determination of pH influence on the sorption effectiveness of dyes, the adsorption kinetics of dyes, as well as the maximum sorption capacity. The study proved that the reaction of rapeseed husk biomass with ammonia can lead to its amination, namely to the introduction of amine functional groups into the material’s structure. The sorption effectiveness of RB5 and RY84 on the tested sorbents was the highest in the pH range of 2–3. The dye sorption kinetics was well described by the pseudo-second-order model. The sorption equilibrium time ranged from 90 to 180 min, and depended on the initial concentration of dyes and the number of amino groups on the sorbent’s surface. The most efficient of the sorbents tested were rapeseed husks pre-activated with epichlorohydrin and then aminated with ammonia. Their sorption capacity determined for RB5 and RY84 was 135.83 mg/g and 114.23 mg/g, respectively, which was 794% and 737% higher than that of the non-modified husks.

Cotton fabric was chemically modified with gelatin, extracted from fleshing waste of collagen by thermal hydrolysis process to increase the dyeing capability of reactive dye. Gelatin imparts new functional groups with fabric and develops Ammonia ion in slightly acid conditions to obtain cationized cotton fabric permit salt and alkali-free reactive dyeing with acceptable shade depth. The imparting of gelatin on the cotton fabric was confirmed by FTIR, UV/VIS absorption, and K/S values. The result shows that they have advantage of high dye utilization and better fastness. Color fastness of treated dyed fabric was equal to the untreated dyed fabric and obtained 4/5 washing fastness, 5 rubbing fastnesses, and 4/5 perspiration fastness. The UV/VIS absorption results show 6.4% improvement in exhaustion and K/S results have 7% improvement in fixation and 9.4% in dye utilization to that of untreated dyeing with salt. Cationized fabric not only increased the exhaustion of the dye but also improved the crease resistance angle at 120° due to the formation of cross-linkage between amide group and the carboxylic acid. To obtain the expected results, cationization was done at alkaline media and the optimum parameter was determined, whereas dyeing conducted at slightly acidic media with optimum parameters.

Digital printing has the potential of enabling cleaner printing or even dyeing of cotton fabrics. However, whilst effluent-free digital printing and dyeing of synthetic textile fabrics have seen some success, the same remain elusive for cotton fabrics. The study reported in this paper aimed to optimize the process parameters of cationic pre-treatment with a view to creating a cleaner cotton fabric digital printing process that could be sustainably implemented at bulk-scale production. Thus, process variables were screened using the one-factor-at-a-time approach to select optimum experimental regions. A Box–Behnken design was used to investigate the combined effect of selected factors namely amount of thickener (150–200 g/L), urea (75–125 g/L) and alkali (10–20 g/L) on the color strength, dye fixation and ink penetration of cationized and digital-printed cotton fabrics. The significant models showed excellent fitting of the data. The optimum levels of the factors, namely, amount of thickener, urea and alkali were found 200 g/L, 125 g/L and 10 g/L, respectively. The bulk-scale experiments carried out at optimum levels have shown that an average of ca. 52% of reactive ink, 37.5% of urea and 50% of alkali can be saved by digital printing of cationized cotton along with generation of nearly colorless effluent.

Reaktif boyarmaddeler pamuğun boyanmasında en yaygın kullanılan boyarmaddelerdir. Pamuklu kumaşların reaktif boyanması için yüksek miktarda kullanılan elektrolit kaçınılmaz olarak çevresel tehditler oluşturmaktadır. Kitosan üstün özelliklerinden dolayı tekstilde birçok alanda farklı amaçlarla kullanılmaktadır. Bu çalışmada, sentetik polielektrolit poli(akrilik asidin sodyum tuzu) reaktif boyamada inorganik elektrolit sodyum klorür yerine kullanımı ve kitosanın kumaşın reaktif boyama davranışı üzerindeki etkileri araştırılmıştır. Ayrıca kumaşların yıkama haslıkları ve ultraviyole koruma faktörleri de gözlemlenmiştir. Boyamadan önce kitosan ile muamele ve boyamada sodyum klorür kullanımı konvansiyonel boyamalara göre renk derinliklerini arttırmış ve bu artış kitosan konsantrasyonundaki artışla devam etmiştir. Öyle ki, %8 konsantrasyonda kitosan uygulamasını takiben %2 konsantrasyonda yapılan boyamadan, %3 konvansiyonel boyamanın renk kuvvetine benzer değerler elde edilmiştir. Sodyum klorür konsantrasyon artışının renk derinliği üzerindeki etkisi polielektrolitten daha belirgin olarak gözlemlenmiştir. Poli (akrilik asidin sodyum tuzunun) pamuğun reaktif boyamasındaki çalışma prensibinin iyonlaşamaması, sıcaklık-konsantrasyon-pH duyarlılığı ve hidrofobik boya kombinasyonları oluşturması nedeniyle nispeten karmaşık olduğu anlaşılmıştır. Ayrıca boyarmaddelerin farklı tuz duyarlılıklarının da elektrolitlerin etkisinde farklılık yaratmış olabileceği düşünülmüştür. Kitosan aplike edilen ve boyanan numunelerin yıkama haslıkları iyi-mükemmel seviyede iken, kitosan aplikasyonunda kullanılan çapraz bağlayıcının bu değerleri 0,5 puan kadar artırdığı görülmüştür. Boyarmaddelerin ultraviyole koruma faktörünü arttırmada kitosandan daha etkili olduğu gözlemlenmiştir.

The dyeing of cotton with synthetic dyes is associated with environmental and health problems, which can be overcome using natural dyes. But in natural dyeing, metal mordants are commonly used, which are also related to harmful effects on the environment and health. That is why the green process should be investigated. In this work, cotton was cationized with proteins from various sources to improve its dyeing with cochineal natural dye. Different techniques for fixing proteins in cotton were evaluated, such as direct cationization in the fabric, fixation by cross-linking, and the oxidation of cotton. All proteins evaluated and their fixation techniques resulted in greater dye adsorption than cotton without cationization. The oxidation of cotton before the application of the protein was the technique that most increased the dye adsorption in all evaluated proteins. However, the fixation of ovalbumin, keratin, and collagen proteins by cross-linking showed higher color strength after the washing process. In view of all the comparisons made, the pretreatment by fixing ovalbumin with cross-linking agent resulted in the higher values of adsorption and color strength, besides a good color uniformity. Thus, ovalbumin is a viable and eco-friendly alternative in the dyeing of cotton with cochineal.

This paper aims to assess the potential for the use of waste cellulosic fibers and recycled grains as materials for the development of abrasives. However, abrasive wear produces low durability and a lot of waste. The improvement of adhesion between the components of composites is the key to extending their lifetime. For this purpose, the surface of the fiber was modified by cationic reactive agents. Composites were manufactured with treated fibers, polyurethane matrix, and iron shavings as abrasive grains. To obtain this product, the coating phenomenon is maintained. DSC and TGA analysis show the thermal stability of abrasives. Contact angle and zeta potential measurements have been used to evaluate the specific surface-chemical changes imparted by surface treatments of specimens. EDX and SEM observations indicate that matrix-reinforcing particle-phase boundaries have a very important effect on the using properties of these materials and revealed that the abrasion resistance of composite is sensitive to fiber/matrix adhesion.

Vinpocetine (VNP), a semisynthetic active pharmaceutical ingredient, is used for oral management of cerebrovascular diseases because of its ability to enhance the blood flow to the brain. However, despite that, the therapeutic application of VNP is restricted due to its reduced bioavailability and diminished brain levels that could be attributed to its low aqueous solubility, short half-life, and presystemic metabolism exposure. Accordingly, the goal of this work was to explore the ability of surface-tailored intranasal emulsomes to boost brain delivery of the drug. A 3221 factorial design was implemented to explore the impact of phospholipid (PL) to solid lipid weight ratio, PL to cholesterol molar ratio, and type of solid lipid on vesicle size, zeta potential, drug entrapment, and release efficiency of the new developed VNP emulsomes. Tailoring of the optimized emulsomal surface formulation was performed using either cationization or PEGylation approaches to boost blood–brain barrier penetration. The pharmacokinetic assessment in rats showed significantly improved bioavailability of VNP emulsomal formulations compared to the oral market product. Additionally, surface-tailored emulsomes exhibited significantly higher brain levels compared to the optimized emulsomes. Based on these findings, the proposed surface-tailored emulsomes could be considered as a promising platform for achieving high brain levels of VNP following intranasal administration.

This work describes the cationization and carboxymethylation of agave fructans and their physicochemical and functional characterization. The results show that the modification gives rise to degrees of substitution of 0.487 and 0.133 for the carboxymethylated and cationic derivatives, respectively. FTIR, DSC and HPLC-SEC results demonstrated the incorporation of quaternary ammonium and carboxymethyl groups in the native fructan molecular structure. As a result of the structure modification, the increase in molecular weight, the appearance of new bands in the FTIR spectrum and changes in thermal properties were observed. The zeta potential demonstrated the anionic and cationic character of the modified fructans. There were no changes in the swelling capacity, however the cationic fructans have a higher oil holding capacity. Native and modified fructans exhibited antimicrobial effect against Staphylococcus aureus, Listeria monocytogenes, Escherichia coli, and Salmonella enterica Typhimurium with higher antimicrobial activity against Gram negative microorganisms.

Textile substrates incorporated with antimicrobial agents offer a great advantage in treating chronic wounds infected with microbes. In this work, a simple one-step process is proposed to develop cellulosic nonwoven incorporated with silver nanoparticles using wet laying technique. In order to improve the dispersion of the fibers during wet laying and better binding of silver nanoparticles, the fibers were cationized using CHPTAC. The decrease in absorbance value of the drain at 470 nm confirms binding of nanosilver to the fiber. A maximum zone of inhibition of 18 mm and 19 mm was obtained for cationized web. The developed web can be used for wound dressing applications.

The biodegradable and non-toxic Bioflocculants have attracted considerable interest as alternative to non-biodegradable chemical flocculants. However, the cost of fermentation media for bioflocculant production and low flocculation efficiency is a major challenge. In this study, we grow Bacillus spp isolated from sediment of local clay pot on spoilt orange juice to produce bioflocculant. The culture supernatant of the bacilli grown on spoilt orange juice were screen for bioflocculant production using Jar test method and Kaolin clay suspension as model wastewater. The effect of pH and temperature on the bioflocculant production were also studied. The effect of cations on bioflocculation rate of the bioflocculant produced were tested via hybridization of the bioflocculant with the cations. The bioflocculation efficiency of the bioflocculant on sample wastewaters were also determined. The bacilli isolated initially had flocculation rate between 31.1±1.6 % to 76.4±1.2% when cultured on screening media. Bioflocculation rate peaked to 77.9% at 40 oC while the lowest flocculation rate (55.41%) was obtained at 25 oC. The optimum bioflocculant production (about 78%) was recorded at pH 6 – 7 while the highest bioflocculant production (84.2%) was achieved at 96th hour of incubation. Na+ and Fe3+ had serious inhibitory effect on the bioflocculant while K+, Ca2+, Mg2+ and Al3+ had less or no effect on the bioflocculant. The bioflocculant had up to 77.7% and 64.5 % on Kitchen wastewater and aquaculture wastewater. This study reveals the potential for utilization of spoilt orange juice as fermentable substrate for bioflocculant production especially if the fermentation conditions and flocculation parameters are well optimized.

Abstract Development of cationic flocculants from lignocellulosic wastes not only eliminates the health and environmental concerns associated with the use of conventional chemicals, but also is the way of waste valorization. In the present study, cellulose fibers extracted from rice husk were cationized through an optimization method based on response surface methodology. The fibers cationized at the optimal conditions had a zeta-potential of 15.2 ± 1.0 mV, while the highest potential was + 8.76 mV, for the samples developed before optimization. FTIR analysis proved the presence of the corresponding functional groups. The functionalized fibers were biodegradable and had absolutely positive surface charges at a broad pH range. The cationized fibers were employed as a flocculant to remove turbidity from the synthetic wastewaters at various pHs and initial turbidities. The cationic fibers showed the excellent turbidity removals up to 98.5% from the synthetic wastewater without the need for conventional coagulants. In contrast to traditionally cationized fibers, the synthesized flocculants did not affect the effluent color during coagulation–flocculation. The charge neutralization and bridging through adsorption were the governing mechanisms of flocculation. The procedure can be applied on lignocellulosic wastes to develop cationic fibers with the excellent flocculation ability and suitable operational characteristics.

Cellulose is the most abundant renewable polymer on Earth and can be obtained from several different sources, such as trees, grass, or biomass residues. However, one of the issues is that not all the fractionation processes are eco-friendly and are essentially based on cooking the lignocellulose feedstock in a harsh chemical mixture, such as NaOH + Na2S, and water, to break loose fibers. In the last few years, new sustainable fractionation processes have been developed that enable the obtaining of cellulose fibers in a more eco-friendly way. As a raw material, cellulose’s use is widely known and established in many areas. Additionally, its products/derivatives are recognized to have a far better environmental impact than fossil-based materials. Examples are textiles and packaging, where forest-based fibers may contribute to renewable and biodegradable substitutes for common synthetic materials and plastics. In this review, some of the main structural characteristics and properties of cellulose, recent green extraction methods/strategies, chemical modification, and applications of cellulose derivatives are discussed.

Cotton cationization with low molecular weight or polymeric cationic modifiers allows the effective dyeing of cotton substrates with reactive dyes under salt-free and more environmentally friendly conditions. The current work focuses on the spectroscopic study of the intermolecular interactions, which dictate the physicochemical process associated with fabric dyeing. Water-soluble cationic copolymers of vinyl benzyl chloride (VBC) and vinyl benzyl triethylammonium chloride (VBCTEAM) have been used as cellulose cationic modifiers. Dye uptake was assessed using Remazol Brilliant Blue R and Novacron Ruby S-3B dyes. The study involves ATR-FTIR, UV-Vis, fluorescence, and XPS spectroscopy. The results of binary polymer-rich dye-polymer aqueous solutions or dye-polymer precipitates at stoichiometric charge-ratio revealed that the sulfonate/sulfate anions of the dyes interact with the cationic VBCTEAM units of the polymer via electrostatic interactions. Moreover, the comparative study of dye application on modified and unmodified fabrics suggests that, unlike the latter, where dyes are chemically bound to cellulose, electrostatic forces dominate the interaction of modified fabrics with dye molecules.

By using the electro-spinning process on natural polymers, it is possible to obtain biodegradable membranes with potential applications in filters and scaffolds for tissue engineering. In this study, a comparison was made between the respective chemical, physical and thermal properties of the fibers from two sources of starch: One derived from a local, indigenous variety of potato (Diacol Capiro), native to the Boyacá region of Colombia (from here on referred to as “local starch”); the other, commercially available starch. A cationization of fibers was also carried out on the two starches. Chemical, physical and thermal properties were analyzed by Fourier transform infrared (FTIR), scanning electron microscopy (SEM), X-ray diffraction (DRX), thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The results showed the fibers were cationized with a highly amorphous state, with a heat resistance of 300°C from physicochemical changes generated in the fibers.

Cationization of cotton is considered to be an effective way to realize salt-free dyeing of reactive dyes. However, applying cotton modified with glycidyltrimethylammonium chloride (GTA) suffers from large consumption of the cationic reagent. One of the reasons is that high crystallinity of cotton fibers hinders the penetration of the reagents into the cellulose interior and limits the reaction between them. This paper designed to use alcohol-water-NaOH system to pretreat the fibers before cationization. With this method, crystallinity of the cotton fibers is decreased and more reactive –OH is exposed, resulting in much higher fiber-reagent reactivity and increased GTA utilization. Influence of alcohol type, alcohol-to-water ratio, and quantity of NaOH on fiber crystallinity and GTA dosage for cationization are all examined. It is found that for achieving 96.0% fixation of C.I. Reactive Black 5 in the absence of salt, GTA dosage can be reduced by half when the fibers are pretreated by alcohol-water-NaOH. Compared with ethanol, n-propanol and isopropanol, tert-butyl alcohol incorporated system shows better performance in increasing fiber reactivity due to their weaker ability to dissolve ions. In this study, XRD and FT-IR are used to demonstrate changes in crystallinity of the fibers after pretreatment. The alteration in micromorphology and hydrophilicity of the pretreated fibers is observed by SEM and water contact angle test, respectively. Furthermore, the alcohol-water-NaOH system can be recycled to show very good repeatability. Notably, all dyed samples pretreated with the system present high color saturation and satisfactory color fastness, especially that the wet rub fastness reaches 4–5 grade, which is one grade higher than that obtained from the conventional dyeing with salt. The above findings prove that alcohol-water-NaOH pretreatment is effective in enhancing reactivity of the cotton fibers and penetrability of the agent, and it shows promising prospects in real application.

The paper examines the influence of cotton cationization on the print quality in terms of penetration, colour yield and colour depth, which have been analysed in comparison to cotton untreated and pretreated with conventional acrylate binder. The process of cationization during mercerization was performed with a cationizing agent Rewin DWR (CHT Bezema). Standard (non-cationized) and cationized fabric, with and without additional layering of binder have been printed by digital inkjet pigment printing method. Moisture management testing (MMT) and dynamic contact angle measurement (drop shape analyzer–DSA30S) were performed on standard and cationized fabric, with and without binder, both with and without pigment layer. After printing, the objective values of colour depth (K/S) and colour parameters L*, C* and h° were analysed. The samples were also analysed by the method of microscopic imaging using a DinoLite microscope. Printed samples were tested to washing fastness, and the results are presented in terms of total colour difference (dECMC), according to CMC(l:c) equation, after the 1st, 3rd, 5th, 7th and 10th washing cycles. Results showed that the cotton cationization will improve the uniformity and coverage of the printed area as well as increase the K/S value. For the samples with binder, the positive effect of cationization on the stability and bond strength between the polymer layer as a pigment carrier with the cotton fabric was confirmed.

The accumulation of dissolved and colloidal substances (DCS) in the increasingly closed paper circulating water system can seriously lower the productivity and safety of papermaking machines, and it has been a challenge to develop an adsorbent with low cost, high adsorption efficiency and large adsorption capacity for DCS removal. In this study, cationic lignocellulose nanofibers (CLCNF) were obtained by cationic modification of agricultural waste bagasse in deep eutectic solvents (DES) followed by mechanical defibrillation, and then CLCNF were employed as an adsorbent for DCS model contaminant polygalacturonic acid (PGA) removal. CLCNF was characterized by transmission electron microscopy, Fourier transform infrared, elemental analysis, X-ray diffraction, and thermogravimetric analysis. The analytical results confirmed the successful preparation of CLCNF with 4.6–7.9 nm diameters and 0.97–1.76 mmol/g quaternary ammonium groups. The effects of quaternary ammonium group contents, pH, contact time and initial concentration of PGA on the adsorption were investigated in a batch adsorption study. According to the results, the cationic modification significantly enhanced the adsorption of PGA by CLCNF and the adsorption performance increased with the increase of the quaternary ammonium group contents. The adsorption of PGA on CLCNF followed the pseudo-second-order and the fitted Langmuir isotherm model. The adsorption showed fast initial kinetics and the experimental maximum adsorption capacity was 1054 mg/g, which is much higher than PGA adsorbents previously reported in the literature. Therefore, CLCNF with high cationic group content developed in this paper is a promising adsorbent for DCS removal.

In this paper, milled corncob powder was treated with sodium chlorite to remove lignin, and the resulting holocellulose was optionally modified with cationic agent. The derivative product was investigated using elemental analysis, Fourier transform infrared (FTIR) spectroscopy, and scanning electron microscopy (SEM). The influences of the dosage of the cationic agent, reaction temperature, particle size, dosage of paper strengthening agent, and pH value of the pulp on the paper physical properties were studied. The results indicated that cationic corncob holocellulose can improve the tensile index, burst index, and folding endurance of paper. When the dosage of cationic agent was 25% and the reaction temperature was set to 70 °C, the resulting tensile index, burst index, and folding endurance increased by 7.15%, 13.74%, and 55.95%, respectively, when compared with the control paper. The particle size of the raw material and the dosage of strengthening agent also greatly influenced the paper’s properties. The SEM analysis showed that the combination of fibers improved the strength properties of the paper after adding the strengthening agent. These results provide a method for value-added use of corncob waste.

Cationic waxy corn starch was prepared from waxy corn starch with 2,3-epoxypropyl trimethyl ammonium chloride (ETMAC) as a cationic etherifying reagent. Its structure was identified by Fourier transform infrared (FTIR) spectroscopy, scanning electron microscopy (SEM), and X-ray powder diffraction (XRD). The results showed that quaternary ammonium groups were introduced successfully into the waxy corn starch, and the cationic reaction occurred on the surface of the starch granules. Cationic waxy corn starch was then applied into deinked pulp as a paper reinforcer, and the result was compared with that of cationic tapioca starch and cationic maize starch. In general, the physical strengths of the paper were improved significantly with an increasing dosage of cationic starches. Cationic waxy corn starch was superior in terms of enhancing the physical properties of paper. In addition, with the use of cationic waxy corn starch, anionic trash in the slurry could be better removed.

Cationic starches were obtained from native starch extracted from cassava of three different varieties at different temperatures (28-50°C) and reaction times (7-24h) using 2,3-epoxypropyltrimethylammonium (EPTAC) as cationizing reactive and NaOH as catalyst in a dry process at ethanolyc medium. The effect of these three factors in the degree of substitution (DS), the reaction efficiency (RE) and functional properties of starch were studied. Degree of substitution (DS) of the cationic starches and functional properties are not significantly affected by the reaction conditions except for the gelatinization temperature, which is affected by the reaction temperature. Starches were obtained with low degrees of substitution between 0.009 and 0.023. Further, the functional properties studied in cationic starches are better than native starches.

Palytoxin (PlTX) and analogues are produced by certain dinoflagellates, sea anemones, corals and cyanobacteria. PlTX can accumulate in the food chain and when consumed it may cause intoxication with symptoms like myalgia, weakness, fever, nausea, and vomiting. The analysis of PlTXs is challenging, and because of the large molecular structure, it is difficult to develop a sensitive and selective liquid chromatography-mass spectrometry (LC-MS/MS) method. In this work, an LC-MS/MS method was developed to analyse PlTXs with use of lithium iodine and formic acid as additives in the mobile phase. For method development, initially, LC-hrMS was used to accurately determine the elemental composition of the precursor and product ions. The main adduct formed was [M + H + 2Li]3+. Fragments were identified with LC-hrMS and these were incorporated in the LC-MS/MS method. A method of 10 min was developed and a solid phase extraction clean-up procedure was optimised for shellfish matrix. The determined limits of detection were respectively 8 and 22 µg PlTX kg−1 for mussel and oyster matrix. Oysters gave a low recovery of approximately 50% for PlTX during extraction. The method was successfully in-house validated, repeatability had a relative standard deviation less than 20% (n = 5) at 30 µg PlTX kg−1 in mussel, cockle, and ensis, and at 60 µg PlTX kg−1 in oyster.

In this study, the cationic Poly[Styrene-Butyl acrylate-(P-vinylbenzyl trimethyl ammonium chloride)] P(St-BA-VBT) nanospheres with N+(CH3)3 functional groups were successfully synthesized by soap-free emulsion polymerization and applied to different fabrics by pad-cure process. After the pad-cure process, the nanospheres were deposited on the surface of the modified cotton fibers successfully without forming a continuous film structure. The X-ray Photoelectron Spectroscopy (XPS) and the Fourier transform infrared (FTIR) results demonstrated that P(St-BA-VBT) nanospheres were adsorbed on the surface of cotton fibers successfully. The excellent color strength value and outline sharpness of the plain, twill, and honeycomb fabrics can be achieved when the nanosphere concentration, sodium bicarbonate, and steaming time were 1 g/L, 10 g/L, and 6 min, respectively. The plain fabrics exhibited the smallest color strength (K/S) values and the best outline sharpness, followed by twill and honeycomb fabrics, which displayed the largest K/S values and the worst outline sharpness after the same treatment. Besides, all the three fabrics showed excellent rubbing fastness and washing fastness. The cationic P(St-BA-VBT) nanospheres modification of the cotton fabrics provides a novel potential approach to obtain good printing efficiency without affecting the tensile breaking strength of cotton fabrics significantly.

Mechanical and chemi-mechanical pulps such as CMP, due to the weaker strength properties, have found limited application in the production of high quality papers as compared with chemical pulps. Therefore, appropriate modification of such fibers could be used to overcome such deficiencies. This study investigated the effect of cationic pretreatment of the CMP fibers to improve the potential of the fibers in paper production. First, fibers were treated by 20% sodium hydroxide, and then the fiber surface was cationized by grafting with one of the dosages of 5, 10 and 15% EPTMAC, based on fiber oven dry weights. The cationized fibers were mixed with 100, 20 and 40 % non-cationized fibers and the mixture was used to make hand sheets. The tensile and burst indices of the hand sheets were measured. The highest tensile and burst indices were measured on hand sheets produced containing either 20 or 40% fibers grafted with 10% cationic agent.