Search

Abstract Marine scrubbers use seawater as washing water and are damaged by sulfur oxides and chlorides during desulfurization. Therefore, surface treatments to enhance corrosion and pitting resistance of scrubber materials must be investigated. This investigation conducts cyclic potentiodynamic polarization experiments to analyze the effects of electropolishing and plasma ion nitiriding of UNS S31603 in washing water. The corrosion current density (0.186 μA cm- 2) of electropolishing is significantly lower than mechanical polishing (1.125 μA cm-2), but plasma ion nitriding is higher (18.995 μA cm- 2). Electropolishing forms a uniform and dense passivation film, increasing corrosion resistance, whereas plasma ion nitriding reduces corrosion resistance due to CrN formation. All specimens present local corrosion. Electropolishing reduces the maximum damage depth by 110.13 μm and increases pitting potential by 0.32 V compared to mechanical polishing. Plasma ion nitriding reduces maximum damage depth by 46.59 μm due to suppression of local acidification during hydrolysis.

Abstract In this investigation, electropolishing and plasma ion nitriding are applied to super austenitic stainless steel for the purpose of improving its corrosion and pitting resistance. Electrochemical experiments are conducted with washing water collected directly from the ship’s scrubber. After electropolishing, the surface roughness is improved by about 73.6% compared to mechanical polishing. After plasma ion nitriding, CrN (precipitate), Fe4N (compound), and γN (solid solution) are observed on the surface. The thickness of the layer formed on the surface is measured to be about 10 μm. A hysteresis loop is observed in the cyclic potentiodynamic polarization curves of mechanical polishing and electropolishing, and the areas are calculated as 23.33 mW cm−2 and 0.17 mW cm−2, respectively. The polarization curve of plasma ion nitriding presents perfect passivation characteristics. Accordingly, mechanical polishing and electropolishing reveal local corrosion, whereas plasma ion nitriding presents a tendency towards general corrosion. In the mechanical polishing, electropolishing, and plasma ion nitriding, the corrosion current densities are 0.665 μA cm−2, 0.093 μA cm−2, and 16.47 μA cm−2, respectively, and the maximum damage depth is observed to grow progressively smaller from plasma ion nitriding to electropolishing and then mechanical polishing.

Abstract Diamond-like carbon (DLC) coating is a surface coating technology with excellent hydrogen permeation resistance and wear resistance. However, it is difficult to completely prevent hydrogen permeation, and when hydrogen penetrates into the coating layer, the DLC coating is adversely affected. Therefore, we investigated the effect of hydrogen embrittlement on the adhesion strength and wear resistance of the DLC coating layer. As the results of the research, the surface roughness of the DLC coating was increased by a maximum of 3.8 times with hydrogen charging, and the delamination ratio of the DLC coating reached about 58%. In addition, the Lc3, which refers to the adhesion strength corresponding to the complete delamination of the DLC coating, was decreased by a maximum of 2.0 N due to hydrogen permeation. In addition, the wear resistance decreased due to hydrogen permeation, and the exposed width of the substrate due to wear increased by more than 4 times. It was also determined that hydrogen blistering or hydrogen-induced cracking occurred at the interface between the DLC coating and the chromium buffer layer due to hydrogen permeation, which decreased the durability of the DLC coating.

Electroless nickel plating is a suitable technology for the hydrogen industry because electroless nickel can be mass-produced at a low cost. Investigating in a complex environment where hydrogen permeation and friction/wear work simultaneously is necessary to apply it to hydrogen valves for hydrogen fuel cell vehicles. In this research, the effects of hydrogen permeation on the mechanical characteristics of electroless nickel-plated free-cutting steel (SUM 24L) were investigated. Due to the inherent characteristics of electroless nickel plating, the damage (cracks and delamination of grain) and micro-particles by hydrogen permeation were clearly observed at the grain boundaries and triple junctions. In particular, the cracks grew from grain boundary toward the intergranualr. This is because the grain boundaries and triple junctions are hydrogen permeation pathways and increasing area of the hydrogen partial pressure. As a result, its surface roughness increased by a maximum of two times, and its hardness and adhesion strength decreased by hydrogen permeation. In particular, hydrogen permeation increased the friction coefficient of the electroless nickel-plated layer, and the damage caused by adhesive wear was significantly greater, increasing the wear depth by up to 5.7 times. This is believed to be due to the decreasing in wear resistance of the electroless nickel plating layer damaged by hydrogen permeation. Nevertheless, the Vickers hardness and the friction coefficient of the electroless nickel plating layer were improved by about 3 and 5.6 times, respectively, compared with those of the free-cutting steel. In particular, the electroless nickel-plated specimens with hydrogen embrittlement exhibited significantly better mechanical characteristics and wear resistance than the free-cutting steel.

Afterglow luminescent particles of ZnS:Ag,Co are developed as an efficient light delivery agent for photochemical tissue bonding in deep tissues with prolonged luminescence.

The Ni-stanogermanides were formed via an interfacial reaction between Ni film and a Ge1−xSnx (x = 0.083) epilayer grown on a Si substrate driven by thermal treatment, and their microstructural and chemical features were investigated as a function of a rapid thermal annealing (RTA) temperature. The Ni3(Ge1−xSnx) phase was formed at the RTA temperature of 300 °C, above which Ni(Ge1−xSnx) was the only phase formed. The fairly uniform Ni(Ge1−xSnx) film was formed without unreactive Ni remaining after annealing at 400 °C. However, the Ni(Ge1−xSnx) film formed at 500 °C exhibited large surface and interface roughening, followed by the formation of Ni(Ge1−xSnx) islands eventually at 600 °C. The Sn concentration in Ni(Ge1−xSnx) gradually decreased with increasing RTA temperature, implying the enhancement of Sn out-diffusion from Ni(Ge1−xSnx) grains during the Ni-stanogermanidation process at higher temperature. The out-diffused Sn atoms were accumulated on the surface of Ni(Ge1−xSnx), which could be associated with the low melting temperature of Sn. On the other hand, the out-diffusion of Sn atoms from Ni(Ge1−xSnx) along its interface was dominant during the Ni/Ge1−xSnx interfacial reaction, which could be responsible for the segregation of metallic Sn grains that were spatially confined near the edge of Ni(Ge1−xSnx) islands.

Abstract Background Wilson disease (WD) is a genetic disorder of copper storage, resulting in pathological accumulation of copper in the body. Because symptoms are generally related to the liver, chelating agents capable of capturing excess copper ions after targeted delivery to the liver are highly required for the treatment of WD. Methods We developed hyaluronate-diaminohexane/black phosphorus (HA-DAH/BP) complexes for capturing copper ions accumulated in the liver for the treatment of WD. Results HA-DAH/BP complexes showed high hepatocyte-specific targeting efficiency, selective copper capturing capacity, excellent biocompatibility, and biodegradability. HA enhanced the stability of BP nanosheets and increased copper binding capacity. In vitro cellular uptake and competitive binding tests verified targeted delivery of HA-DAH/BP complexes to liver cells via HA receptor mediated endocytosis. The cell viability test confirmed the high biocompatibility of HA-DAH/BP complexes. Conclusion HA-DAH/BP complexes would be an efficient copper chelating agent to remove accumulated copper in the liver for the WD treatment.

Abstract Diabetic retinopathy is currently treated by highly invasive repeated therapeutic injections and surgical interventions without complete vision recovery. Here, a noninvasive smart wireless far red/near‐infrared (NIR) light emitting contact lens developed successfully for the repeated treatment of diabetic retinopathy with significantly improved compliance. A far red/NIR light emitting diode (LED) is connected with an application‐specific integrated circuit chip, wireless power, and communication systems on a PET film, which is embedded in a silicone elastomer contact lens by thermal crosslinking. After in vitro characterization, it is confirmed that the retinal vascular hyper‐permeability induced by diabetic retinopathy in rabbits is reduced to a statistically significant level by simply repeated wearing of smart far red/NIR LED contact lens for 8 weeks with 120 µW light irradiation for 15 min thrice a week. Histological analysis exhibits the safety and feasibility of LED contact lenses for treating diabetic retinopathy. This platform technology for smart LED contact lens would be harnessed for various biomedical photonic applications.

In this paper, we studied the effects of the intersection angle between the inlet channels on the droplet diameter using a COMSOL Multiphysics® simulation. We employed the level-set method to study the droplet generation process inside a microfluidic flow device. A flow-focusing geometry was integrated into a microfluidics device and used to study droplet formation in liquid–liquid systems. Droplets formed by this flow-focusing technique are typically smaller than the upstream capillary tube and vary in size with the flow rates. Different intersection angles were modeled with a fixed width of continuous and dispersed channels, orifices, and expansion channels. Numerical simulations were performed using the incompressible Navier–Stokes equations for single-phase flow in various flow-focusing geometries. As a result of modeling, when the dispersed flow rate and the continuous flow rate were increased, the flow of the continuous flow fluid interfered with the flow of the dispersed flow fluid, which resulted in a decrease in the droplet diameter. Variations in the droplet diameter can be used to change the intersection angle and fluid flow rate. In addition, it was predicted that the smallest diameter droplet would be generated when the intersection angle was 90°.

The purpose of this study was to identify the characteristics of blood flow in aortic coarctation based on stenotic shape structure, stenosis rate, and the distribution of the wall load delivered into the blood vessels and to predict the impact on aneurysm formation and rupture of blood vessels by using a computational fluid dynamics modeling method. It was applied on the blood flow in abdominal aortic blood vessels in which stenosis occurred by using the commercial finite element software ADINA on fluid-solid interactions. The results of modeling, with an increasing stenosis rate and Reynolds number, showed the pressure drop was increased and the velocity was greatly changed. When the stenosis rate was the same, the pressure drop and the velocity change were larger in the stenosis with a symmetric structure than in the stenosis with an asymmetric one. Maximal changes in wall shear stress were observed in the area before stenosis and minimal changes were shown in stenosis areas. The minimal shear stress occurred at different locations depending on the stenosis shape models. With an increasing stenosis rate and Reynolds number, the maximal wall shear stress was increased and the minimal wall shear stress was decreased. Through such studies, it is thought that the characteristics of blood flow in the abdominal aorta where a stenosis is formed will be helpful in understanding the mechanism of growth of atherosclerosis and the occurrence and rupture of the abdominal aortic flow.

Herein we report a method for the synthesis of 3,4,5-trisubstituted isoxazoles in water under mild basic conditions at room temperature via a [3 + 2]-cycloaddition of nitrile oxides and 1,3-diketones, β-ketoesters, or β-ketoamides. We optimized the reaction conditions to control the selectivity of the production of isoxazoles and circumvent other competing reactions, such as O-imidoylation or hetero [3 + 2]-cycloaddition. The reaction happens fast in water and completes within 1–2 hours, which provides an environmentally friendly access to 3,4,5-trisubstituted isoxazoles, an important class of structures found in numerous bioactive natural products and pharmaceuticals. Additionally, we optimized the reaction conditions to produce trifluoromethyl-substituted isoxazoles, a prevalent scaffold in biomedical research and drug discovery programs. We also proposed a plausible mechanism for the selectivity of the [3 + 2]-cycloaddition reaction to produce 3,4,5-trisubstituted isoxazoles. Not to be overlooked are our optimized reaction conditions for the dimerization of hydroximoyl chlorides to form furoxans also known as 1,2,5-oxadiazole 2-oxides, a class of structures with important biological activities due to their unique electronic nature and coordination ability.

Agricultural crop productivity relies on the application of chemical pesticides to reduce pest and pathogen damage. However, chemical pesticides also pose a range of ecological, environmental and economic penalties. This includes the development of pesticide resistance by insect pests and pathogens, rendering pesticides less effective. Alternative sustainable crop protection tools should therefore be considered. Semiochemicals are signalling molecules produced by organisms, including plants, microbes, and animals, which cause behavioural or developmental changes in receiving organisms. Manipulating semiochemicals could provide a more sustainable approach to the management of insect pests and pathogens across crops. Here, we review the role of semiochemicals in the interaction between plants, insects and microbes, including examples of how they have been applied to agricultural systems. We highlight future research priorities to be considered for semiochemicals to be credible alternatives to the application of chemical pesticides.

Polyketides are secondary metabolites mainly found in aerobic organisms with wide applications in medicine and agriculture. Here, the authors uncover new polyketides native to the anaerobic bacterium Clostridium acetobutylicum and show their role in triggering sporulation and granulose accumulation.

Comparing a solution phase route to a solid phase route in the synthesis of the cytotoxic natural product urukthapelstatin A (Ustat A) confirmed that a solid phase method is superior. The solution phase approach was tedious and involved cyclization of a ridged heterocyclic precursor, while solid phase allowed the rapid generation of a flexible linear peptide. Cyclization of the linear peptide was facile and subsequent generation of three oxazoles located within the structure of Ustat A proved relatively straightforward. Given the ease with which the oxazole Ustat A precursor is formed via our solid phase approach, this route is amenable to rapid analog synthesis.