Search

Superconducting (SC) tokamak JT-60SA plays an essential role in fusion research and development by supporting and complementing the ITER project, providing directions to the DEMO design activity and fostering next generation scientists and engineers. Since the short circuit incident at the terminal joints of equilibrium field coil #1 during the integrated commissioning (IC) in March 2021, both EU and JA implementing agencies (IAs) have examined how to ensure safe operation of JT-60SA by mitigating the risk of possible discharge occurrence inside the cryostat. Based on the experience of the global Paschen tests, the IAs have established a strategy of risk mitigation measures, which is a combination of (i) reinforcement of insulation, (ii) avoiding unnecessary voltage application to the coil systems and (iii) immediate de-energization of the coils when deteriorated vacuum conditions are detected. Thanks to the considerable efforts of the Integrated Project Team members, the IC restarted in May 2023. After confirmation of the SC state of the coil systems (TF, EF and CS), the coil energization test and the plasma operation phase 1 (OP-1) started. The first plasma was successfully achieved on 23 October 2023 with a limited value of voltage and current applied to the coils. The plasma configuration control was also confirmed with low plasma current and low auxiliary heating power conditions. Based on the IO–F4E–QST collaboration, activities of JT-60SA have been shared with the IO and provided an important lesson for ITER assembly and commissioning, and will provide an outstanding contribution to fusion research at large. After OP-1, maintenance & enhancement phase 1 (M/E-1) starts from January 2024, in which in-vessel components are installed, and heating and diagnostic systems are extensively upgraded to allow a high power heating experiment planned in OP-2. In order to make the best use of JT-60SA, a newly organized JT-60SA experiment team will refine the research plan for the future high heating power operation phase.

The elimination of the need for an Ohmic heating solenoid may be the most impactful design driver for the realization of economical compact fusion tokamak reactor systems. However, this would require fully non-inductive start-up and current ramp-up from zero plasma current and low electron temperature of sub-keV to the full plasma current of ∼10–15 MA at 20–30 keV electron temperature. To address this challenge, an efficient solenoid-free start-up and ramp-up scenario utilizing a low-field-side-launched extraordinary mode at the fundamental electron cyclotron harmonic frequency (X–I) is proposed, which has more than two orders of magnitude higher electron cyclotron current drive (ECCD) efficiency than the conventional ECCD for the sub-keV start-up regime. A time dependent model was developed to simulate the start-up scenarios. For the Spherical Tokamak Advanced Reactor (STAR) (Menard et al 2023 Next-Step Low-Aspect-Ratio Tokamak Design Studies (IAEA)), it was found that to fully non-inductively ramp-up to 15 MA, it would take about 25 MW of EC power at 170 GHz. Because of the relatively large plasma volume of STAR, radiation losses must be considered. It is important to make sure that high Z impurities are kept sufficiently low during the early current start-up phase where the temperature is sub-keV range. Since the initial current ramp up takes place at a factor of ten lower density compared to the sustained regimes, it is important to transition into a higher bootstrap fraction discharge at lower density to minimize the ECCD power requirement during the densification. For the sustainment phase an array of eight gyrotron launchers with a total of about 60 MW of fundamental O-mode was found to be sufficient to provide the required axis-peaked external current drive. High efficiencies between 19–57 kA MW ^−1 were found with optimal aiming, and these were resilient to small changes in aiming angles and density and temperature profiles.

The plasma current start-up experiment is conducted through electron cyclotron (EC) heating in the QUEST spherical tokamak. During the EC heating, the application of a toroidal electric field in the opposite direction to the plasma current effectively inhibits the growth of energetic electrons. Observations show rapid increases in plasma current and hard x-ray count immediately following the cancellation of the retarding electric field. When a compact tokamak configuration maintains equilibrium on the high field side, along with the retarding field, it leads to effective bulk electron heating. This heating achieved an electron temperature of T _e ≈ 1 keV at electron density n _e > 1.0 × 10 ^18 m ^−3 . Ray tracing of the EC wave verifies that more power absorption into plasma through a single-pass occurs around the second resonance layer with higher values of electron density and temperature.

Results from the successful solenoid-free plasma startup using the method of transient coaxial helicity injection (transient CHI) in the QUEST spherical tokamak (ST) are reported. Unlike previous applications of CHI on HIT-II and on NSTX which required two toroidal insulating breaks to the vacuum vessel, QUEST uses a first of its kind, floating single biased electrode configuration, which does not use such a vacuum break. Instead, the CHI electrode is simply insulated from the outer lower divertor plate support structure. This configuration is much more suitable for implementation in a fusion reactor than the previous configurations. Transient CHI generated toroidal currents of 135 kA were obtained. The toroidal current during the formation of a closed flux configuration was over 50 kA. These results bode well for the application of transient CHI in a new generation of compact high-field STs and tokamaks in which the space for the central solenoid is very restricted.

Spatially resolved rotational temperature of ground state hydrogen molecules desorbed from plasma-facing surface was measured in QUEST, LTX-β, and DIII-D tokamaks, and the increases of the rotational temperature with the surface temperature and due to collisional-radiative processes in the plasmas were evaluated. The increase due to collisional-radiative processes was calculated by solving rate equations considering electron and proton collisional excitation and deexcitation and spontaneous emission. The calculation results suggest a high sensitivity for the rotational temperature to electron and proton densities, but a negligible sensitivity to the electron, proton, and surface temperatures. In the three tokamaks with different plasma parameters and plasma-facing surface materials, the spatial profile of the rotational temperature was estimated using Fulcher-α emission lines (600–608 nm). In QUEST, the spatial profile of the rotational temperature was estimated from spatially resolved spectra. In the other tokamaks, the rotational temperature was evaluated assuming a single point emission with a location determined from the Fulcher-α emission profile as measured with a filtered camera. In metal-walled devices QUEST and LTX-β, the rotational temperature increased with the surface temperature, and the calculated collisional-radiative increase is consistent with measured increase assuming that the rotational temperature at the surface is approximately 500–600 K higher than the surface temperature. In DIII-D with carbon walls, a larger collisional-radiative increase than the other tokamaks was observed because of the higher density leading to a large difference from the calculated increase compared to the other smaller tokamaks. Measurement of the Fulcher-α emission profile with higher spatial resolution in DIII-D may reduce the difference and reveal the effect of the surface temperature on the rotational temperature. These results show the increases in the rotational temperature with the surface temperature and due to the collisional-radiative processes.

QUEST (Q-shu university experiment with steady state spherical tokamak) is a midsize spherical tokamak capable of steady-state operation, comprising all-metal plasma-facing walls and a hot wall (HW) to address issues pertaining to fuel particle balance. The HW was installed summer 2014. Quantitative analysis pertaining to the HW at 373 K is carried out, and clarify the quantitative impact of shot history that obviously appears in wall stored hydrogen just before the discharge at the wall temperature. The model indicates the plasma-induced deposition layer play an essential role in fuel particle balance. A clear temperature dependence of fuel recycling was observed using outgassing just after plasma termination and played an essential role in regulation of particle balance. Consequently, long duration discharges lasting more than 1 h has been obtained at wall temperature, TW

This research investigated fuel particle balance during long duration discharge in an all-metal plasma facing wall (PFW) through intensive QUEST execution. A simple wall model including the plasma-induced deposition layer that creates hydrogen (H) barriers, called the H barrier model, was established. A simple calculation, based on a combination of H state rate equations and the H barrier model, was applied to real plasma in the early phase of its longest discharge. The model accurately reconstructed the evolutions of electron density and wall-stored H over time, proper values are chosen for the parameters that are difficult to determine experimentally. Comparative calculations that used the H barrier and a fully reflective models, predicted significant impacts of wall models on the plasma density time response and value of electron density, indicating that a proper wall model should be developed for all-metal PFW devices. Keywords: Fuel particle balance, steady state operation, Hydrogen barrier model, QUEST

To study radial distribution of hydrogen flux in peripheral plasma in long duration tokamak discharges, permeation and Langmuir reciprocate probes are used. The atomic hydrogen flux to the walls at several radial positions is deduced from the permeation flux. Contribution of the ions to the hydrogen flow is deduced from the Langmuir probe ion saturation current. It is found, that the atomic hydrogen has the most contribution to the hydrogen flow behind the plasma facing components (PFCs), while the ion flux there is negligible. The atomic flux behind the PFCs drops to the value of F~4.3×1015H/m2/s, which is ~6 % of that just in front of PFCs, F~7.7×1016H/m2/s.

A spectroscopic system with multiple viewing chords was developed for QUEST (Q-shu University Experiment with Steady-State Spherical Tokamak) to measure the spatial distribution of ion toroidal velocities in discharges sustained by electron cyclotron resonance heating (ECH). Twenty-four viewing chords were aligned in the midplane and C III emission line spectra were measured for three types of ECH discharge under different magnetic field configurations. By applying an inversion method to the measured spectra, we evaluated the radial distributions of C2+ ion emissivity, temperature, and toroidal velocity. The error in the evaluated velocity was estimated to be less than 5 km/s. It was found that the velocity depends on the magnetic field configuration.

In order to understand the atomic hydrogen distribution in different kinds of plasma and its influence on the recycling, two kinds of plasmas were used: non-confined annular electron cyclotron resonance (ECR) and confined long duration plasmas. The permeation probes are used to measure directly the atomic hydrogen flux at several poloidal positions. The permeation through metals due to the ion and atom component of the hydrogen flux to the wall is indistinguishable. To estimate the contribution of the ions directly, Langmuir probes were used. The Гinc profile behind the plasma facing components (PFCs) is almost constant, ∼2 ×1018 H/s/m2.