Search

This research was designed to assess the yield and quality of ash prepared from different types of waste papers. Waste newspapers, writing papers, and cartons were selected for combustion to obtain the ashes and coded as WNPA, WWPA, and WCPA, respectively. The waste papers were incinerated simultaneously in separate but identical incinerators at 850 ℃. An experiment on the yield of the ashes was performed on two days before the ashes obtained were mixed based on the type of waste papers from which they were derived. The results showed that irrespective of the day and time, the WCPA was the most yielded (14.1%), followed by the WWPA (12.3%), and then the WNPA (11.9%). Also, it was found that all the ashes possessed flow properties acceptable for engineering applications. However, the WCPA would ensure the best performance if applied, especially as a partial replacement material for cement. While the WWPA was found to be richer than the WNPA, the WCPA was the richest in terms of the proportions of key oxides for strength development. In general, the percentages of various chemical components of each ash complied with the standard specifications for cement except in the case of losses on ignition of the WNPA and WWPA, which were about 0.53% and 0.02%, respectively, beyond the maximum stipulated value.

To improve the accuracy and efficiency of the aging life prediction and assessment of transformer oil-paper insulation, and to make up for the deficiencies of traditional characterizers, such as 2-furfural, carbon monoxide, and carbon dioxide, a method for the simultaneous determination of methanol, ethanol, $n-\mathbf{propanol}$, and $n$-butanol in oil with a single injection is established by headspace-gas chromatography-mass spectrometry. The measured results show that the determination limits of the four alcohol characterizers can be controlled to $\mathbf{10}\ \mu \mathbf{g}/\mathbf{kg}$ level. Based on this method, the change patterns of the above four alcohols with thermal aging time and degree of polymerization are obtained through thermal aging experimental research. Ethanol, $n$-propanol, and $n$-butanol in oil indicate nearly linear correlations with thermal aging time and degree of polymerization, similar to that of methanol. By analyzing 52 sets of measured data of 500 kV EHV transformers in operation, $n$-butanol is found to have excellent performance, and a new method to evaluate the aging state of oil-paper insulation employing $n$-butanol and methanol is proposed along with the aging attention value model. The measured data of 500 kV EHV transformers in operation indicate that the combination of $n$-butanol and methanol as the preferred characterizers can effectively compensate for the shortcoming of traditional characterizers in the early stages of aging, and the feasibility of the method is verified. Two possible pathways for the generation of $n$-butanol by cellulose cleavage during the aging of oil-paper are proposed from the chemical structure of cellulose.

Abstract We report an innovative and facile approach to fabricating an ultrasensitive plasmonic paper substrate for surface-enhanced Raman spectroscopy (SERS). The approach exploits the self-assembling capability of poly(styrene-b-2-vinyl pyridine) block copolymers to form a thin film at the air-liquid interface within the single microdroplet scale for the first time and the subsequent in situ growth of silver nanoparticles (AgNPs). The concentration of the block copolymer was found to play an essential role in stabilizing the droplets during the mass transfer phase and formation of silver nanoparticles, thus influencing the SERS signals. SEM analysis of the morphology of the plasmonic paper substrates revealed the formation of spherical AgNPs evenly distributed across the surface of the formed copolymer film with a size distribution of 47.5 nm. The resultant enhancement factor was calculated to be 1.2 × 107, and the detection limit of rhodamine 6G was as low as 48.9 pM. The nanohybridized plasmonic paper was successfully applied to detect two emerging pollutants—sildenafil and flibanserin—with LODs as low as 1.48 nM and 3.45 nM, respectively. Thus, this study offers new prospects for designing an affordable and readily available, yet highly sensitive, paper-based SERS substrate with the potential for development as a lab-on-a-chip device.

Abstract This study identifies important factors for designing an effective biomimetic paper‐based fog harvesting substrate by examining the harvesting properties of different surfaces, including glass, polyethylene, and superhydrophobic paper. In laboratory‐scale fogging tests, the wetting behavior of the substrates is characterized, and the importance of the tilt angle of the respective surface relative to the fog flow is elaborated. Because successful fog harvesting requires both efficient accumulation of water droplets on the surface (by condensation and collision) and sufficient but not excessive roll‐off of the liquid, the amount of water finally collected is clearly related to the pinning effect, which should prevent the smallest droplets from being carried away by the wind but must not lead to full and permanent wetting of the surface. Coalescence is identified as a major phenomenon to improve droplet roll‐off. In this context, superhydrophobic paper indicates to be a more effective water collector than glass or polyethylene, especially when oriented vertically, since it allows the droplets to roll off very efficiently. Finally, the addition of glass particles to the superhydrophobic coating is proposed as a means of enhancing pinning and improving the fog harvesting efficiency.

Since the last two decades, the use of natural fiber reinforced polymer composites has garnered significant application considerations over the synthetic fiber reinforced composites due to their numerous advantages and unique properties. Likewise, epoxy resin has attracted the interest of many researchers for composite synthesis, basically because of its chemical stability, thermal and mechanical characteristics. Hence, the primary aim of this study was to investigate the influence of dombeya fiber and paper particulate on the physical and mechanical properties of dombeya fiber and paper particulate-reinforced polymer composites for structural applications. Dombeya fiber and paper particles are renewable and biodegradable materials, thereby making them environmentally friendly materials to replace synthetic materials. Hand lay-up technique was utilized to fabricate the hybrid-reinforced biocomposites after which they were subjected to mechanical, wear, density, and moisture absorption properties. The surface morphology of the fractured surface was also analyzed to investigate its microstructural features. It was discovered from the results that hybrid biocomposites demonstrated improved properties over the unreinforced composite, with composites from 9-wt% dombeya fiber-paper particles reinforced biocomposite exhibiting the most suitable properties with commensurate density with the unreinforced epoxy matrix. These obtained characteristics support the material as a suitable material for biomedical apparatus application such as orthopedic implants, surgical instruments, and bone fixation devices.

Power transformers are critical equipment responsible for the transmission and transformation of electrical energy, and they are an important component of power system. Under the combined effects of electric field, thermal field, and mechanical stress, insulation degradation is prone to occur in oil-paper insulation structures. Among them, the “liquid-solid” interface formed by oil and oil-immersed pressboard is the weak point in transformer insulation, and extensive operational experience has shown that creeping flashover of insulating pressboard is a common fault in power transformers. Creeping flashover of insulating pressboard can rapidly destroy the insulation structure, leading to irreversible damage to the transformer and posing a serious risk of transformer accidents. In recent years, many scholars have conducted in-depth research on the characteristics and mechanisms of creeping flashover in oil-paper insulation structures using various experimental methods. They have obtained significant findings that have important theoretical and practical implications for optimizing the structure of power transformers and improving their reliability. This paper first introduces the characteristics of the electromagnetic environment inside the power transformer and the common forms of creeping flashover accidents in engineering. Then, classified according to the uneven degree of electric field and creepage distance of test electrodes used in relevant research, and the test methods and flashover characteristics of small size (

Abstract Paper, an inexpensive material with natural biocompatibility, non‐toxicity, and biodegradability, allows for affordable and cost‐effective substrates for unconventional advanced electronics, often called papertronics. On the other hand, polymeric elastomers have shown to be an excellent success for substrates of soft bioelectronics, providing stretchability in skin wearable technology for continuous sensing applications. Although both materials hold their unique advantageous characteristics, merging both material properties into a single electronic substrate reimagines paper‐based bioelectronics for wearable and patchable applications in biosensing, energy generation and storage, soft actuators, and more. Here, a breathable, light‐weighted, biocompatible engineered stretchable paper is reported via coaxial nonwoven microfibers for unconventional bioelectronic substrates. The stretchable papers allow intimate bioconformability without adhesive through coaxial electrospinning of a cellulose acetate polymer (sheath) and a silicone elastomer (core). The fabricated cellulose‐silicone fibers exhibit a greater percent strain than commercially available paper while retaining hydrophilicity, biocompatibility, combustibility, disposable, and other natural characteristics of paper. Moreover, the nonwoven stretchable cellulose‐silicone fibrous mat can adapt conventional printing and fabrication process for paper‐based electronics, an essential aspect of advanced bioelectronic manufacturing.

The selective detection of halides in aqueous samples is crucial for addressing environmental and physiological concerns. Consequently, the development of an affordable, portable, and user-friendly sensing platform for rapid halide detection holds substantial promise. In this study, we present a novel paper-based nanosensor as an appealing alternative for selectively detecting halides in water. This nanosensor leverages the optical properties of silver nanoparticles (ranging from 50 to 250 nm) embedded in epoxy resin and printed on filter paper. We elucidate the colorimetric behavior of this nanosensor in response to specific halides (chloride, bromide, and iodide) upon contact. Importantly, this sensor discerns, through a single measurement, the presence of these halides in aqueous media with remarkable selectivity. The nanosensor manifests distinct color changes in reaction to different halides, particularly at elevated concentrations (ranging from 2 to 400 mM), surpassing the saturation levels observed in other proposed sensors. These discernible color changes are due to the oxidation of silver nanoparticles, changing their morphology and aggregation density, and can be readily detected and analyzed directly from a captured image. Consequently, it demonstrates considerable potential for integration into automated qualitative monitoring devices based on chromaticity analysis.

This paper discusses the results of the micro-Raman analysis performed on paper-like graphene oxide (GO) samples consisting of many functionalised graphene layers and annealed at moderate temperatures (≤500 °C) under vacuum conditions (p ≃ 10−4 mbar). The analysis of the standalone samples revealed that the obtained material is characterised by a noticeable disorder level but still stays below the commonly accepted threshold of high or total disorder. GO formed in a simple way showed two spectral bands above 1650 cm−1 recorded very rarely or not at all and their origin has been discussed in detail. The results also confirmed the metastable character of multilayer GO after the annealing process at moderate temperatures as the C/O ratio was kept between 2 and 3 and the spectral features were stable within the annealing temperature range.

Invasive alien plant species (IAPS) may cause threats to native biodiversity in ecosystems. Researchers have been investigating all the possible ways that they can be used effectively for other purposes. Since IAPS are capable of forming cellulose fibre nets, in this research, papers were made from three different types of IAPS (Japanese knotweed, giant goldenrod, and black locust). This research examined these IAPS papers and their effectiveness when used as printing substrates. In comparison to commercial office paper, the differences in basic, surface, optical, and microscopic properties were measured. As a widely used technology, inkjet printing was applied. We tested a commonly used sans-serif typeface (which has been established as being more legible than other typefaces in previous research) in three different type sizes (i.e., 8, 10, and 12 pt). According to the results, paper made from IAPS could offer some usable properties and acceptable legibility, especially when printing typefaces with specific attributes, such as moderate counter size, higher x-height, and minimal differences in the letter stroke width, are used. An appropriate typographic tonal density should be achieved in combination with an adequate letter size, e.g., 10 pt type size when a sans-serif typeface is used.