Search

Natural and synthetic esters are increasingly being chosen instead of mineral oil for environmental and fire safety reasons. However, their use in power transformers is limited due to insufficiently well-understood ageing processes affecting their properties and the properties of cellulosic materials impregnated with them. The research results presented in many scientific papers prove that the use of esters slows the ageing process of cellulosic materials. This article presents the results of research aimed at answering the question of whether the effect of slowing the ageing process will also occur in the case of insulation with very low initial moisture. The answer to this question will allow us to better understand the role of water in the ageing process of the transformer’s insulation system. The thermal ageing process was carried out at a temperature of 150 °C in closed systems. The degree of cellulose polymerisation was taken as a measure of the degree of paper ageing. Great attention was paid to measuring the water content in both paper and electro-insulating liquids at various stages of their ageing. Furthermore, measurements of the properties of electro-insulating liquids were made, which are considered markers of ageing. The test results obtained indicate that in the case of a dry insulation system, corresponding to the initial moisture of the new units, the type of liquid used to impregnate the cellulosic material does not significantly affect its depolymerisation process. However, in the case of paper impregnated with natural esters, a lower dynamic of moisture increase in insulation was observed.

The aim of this research is to predict the mechanical properties along with the behaviors of standard insulating paper used in power transformers under thermal aging. This is conducted by applying an artificial neural network (ANN) trained with a multiple regression model and a particle swarm optimization (MR-PSO) model. The aging of the paper insulation is monitored directly by the tensile strength and the degree of polymerization of the solid insulation and indirectly by chemical markers using 2-furfuraldehyde compound content in oil (2-FAL). A mathematical model is then developed to simulate the mechanical properties (degree of polymerization (DPV) and tensile index (Tidx)) of the aged insulation paper. First, the datasets obtained from experimental results are used to create the MR model, and then the optimizer method PSO is used to optimize its coefficients in order to improve the MR model. Then, an ANN method is trained using the MR-PSO to create a nonlinear correlation between the DPV and the time, temperature, and 2-FAL values. The acquired results are assessed and compared with the experimental data. The model presents almost the same behavior. In particular, it has the capability to accurately simulate the nonlinear property behavior of insulation under thermal aging with an acceptable margin of error. Since the life expectancy of power transformers is directly related to that of the insulating paper, the proposed model can be useful to maintenance planners.

The article presents studies on the impact of the significant process parameters of a paper machine with a Yankee cylinder on its production capacity and heat energy consumption for drying the paper web. Parameters such as machine speed, web moisture content before and after pressing, parameters of steam supplied to the cylinder and parameters of hot air flowing from the nozzles of the hood were analyzed. The study’s results were used to optimize production to improve the energy efficiency and performance of the machine. In order to use the possible methods of improving the production capacity and heat energy consumption, the parameters of the production process were measured and the basic indicators characterizing the operation of the machine were calculated in the Yankee cylinder–dryer hood system. The correct functioning of the machine components and the possibility of their modernization were also analyzed. Technological and construction changes introduced based on the research results made it possible to increase the production capacity by 10% and to reduce the consumption of heat energy per 1 ton of produced paper by 16.3%. The article presents a description of changes in the technology of paper production and modernization of the tissue machine made in the years 2013–2022.

Insulation cellulose paper is a basic measure for a power transformer’s remaining useful life, and its advantageous low cost, electrical, and mechanical properties have made it an extensive insulation system when impregnated in a dielectric liquid. Cellulose paper deteriorates as a result of ageing due to some chemical reactions like pyrolysis (heat), hydrolysis (moisture), and oxidation (oxygen) that affects its degree of polymerization. The condition analysis of cellulose paper has been a major concern since the collection of paper samples from an operational power transformer is almost impossible. However, some chemicals generated during cellulose paper deterioration, which were dissolved in dielectric liquid, have been used alternatively for this purpose as they show a direct correlation with the paper’s degree of polymerization. Furthermore, online and non-destructive measurement of the degree of polymerization by optical sensors has been proposed recently but is yet to be available in the market and is yet generally acceptable. In mitigating the magnitude of paper deterioration, some ageing assessments have been proposed. Furthermore, researchers have successfully enhanced the insulating performance of oil-impregnated insulation paper by the addition of various types of nanoparticles. This study reviews the ageing assessment of oil-paper composite insulation and the effect of nanoparticles on tensile strength and electrical properties of oil-impregnated paper insulation. It includes not only significant tutorial elements but also some analyses, which open the door for further research on the topic.

Chemical compounds dissolved in insulating oil, as indicators can excellently monitor the paper aging condition, which has attracted increasing interest in areas of transformer condition monitoring and fault diagnosis. Because of their outstanding features, such as good correlation with the degree of polymerization of cellulose paper and the aid of non-destructive online monitoring, chemical indicators have been effectively used for transformer condition assessment. In this study, a comprehensive, in-depth insight into the indicators of the aging of insulating paper from aging characteristics, physico-chemical characteristics, shortcomings of various compounds, generation pathways and mechanisms, and monitoring technologies are provided. It is expected that these chemical indicators can provide better guidance for the evaluation of paper insulation performance and transformer aging. In addition, the latest research progress, as well as current challenges and future prospects are also outlined. This study provides a theoretical basis and reference for chemical indicators in the fields of microscopic formation mechanism, diffusion equilibrium phenomenon, and insulation aging state assessment.

The pulp and paper industry (PPI) has several opportunities to contribute to meeting prevailing climate targets. It can cut its own CO2 emissions, which currently account for 2% of global industrial fossil CO2 emissions, and it has an opportunity to produce renewable energy, fuels, and materials for other sectors. The purpose of this study is to improve understanding of the decarbonization prospects of the PPI. The study provides insights on the magnitude of needed annual renewal rates for several possible net-zero target years of industrial fossil CO2 emissions in the PPI and discusses decarbonization opportunities, namely, energy and material efficiency improvement, fuel switching, electrification, renewable energy production, carbon capture, and new products. The effects of climate policies on the decarbonization opportunities are critically evaluated to provide an overview of the current and future business environment of the European PPI. The focus is on Europe, but other regions are analyzed briefly to widen the view. The analysis shows that there are no major technical barriers to the fossil-free operation of the PPI, but the sector renovates slowly, and many new opportunities are not implemented on a large scale due to immature technology, poor economic feasibility, or unclear political environment.

The building sector contributes to 40% of the total final energy consumption and 36% of CO2 emissions in Europe, and these are set to increase in the coming years. International directives are pushing towards a decarbonisation roadmap to improve the quality of cities and the health of citizens. Buildings have a potentially central role in terms of energy transition as a means to produce and save energy. Photovoltaic shading devices (PVSDs) protect buildings from direct solar radiation and overheating while producing renewable electricity onsite and increasing the users’ thermal comfort. Even though the potential of the PVSD is considerable, the sector is still unexplored, and few studies on the topic are available in the literature. This systematic review aims to present an exhaustive overview of the current literature on state-of-the-art PVSDs by analysing the scientific framework in terms of the status of the research. It presents a performance-based approach focusing on innovative products, PVSD design strategies, and energetic performance in distinct climate conditions and configurations. In particular, 75 articles and about 250 keywords were identified, selected, and analysed. The literature review serves as a basis for further R&D activities led by both the industrial and the academic sectors.

Numerical simulation of polypropylene laminated paper insulation is a serious challenge, as it must take into account the layered structure and presence of longitudinal and radial gaps in the coils of the winded tape for cables with sector-shape conductive cores. Thus far, it has been performed only with serious simplifications. We propose a technique for numerical modeling of electric parameters in this type of insulation by reducing a complex 3D problem to a simplified 2D model that takes into account the main influencing factors. The results of modeling the distribution of electric field strength and current density in insulation are presented, and the influence of the location of gaps between the edges of winded tape on the conductivity of cable insulation is estimated. Analytical expressions are obtained for estimating the electrical resistance of insulation while taking into account the parameters of the butt gap between the insulating tapes. The results of calculations, numerical modeling, and experimentally measured values of electrical resistance are compared, showing that there is a good match. The main effects affecting the properties of polypropylene laminated paper insulation are described.

The treatment and disposal of sewage sludge is one of the most important and critical issues of wastewater treatment plants. One option for sludge liquidation is the production of fuel in the form of pellets from mixed sewage and paper mill sludge. This study presents the results of the combustion of pelletized fuels, namely sewage and paper mill sludge, and their 2:1 and 4:1 blends in a fluidized bed combustor. The flue gas was analysed after reaching a steady state at bed temperatures of 700–800 °C. Commonly used flue gas cleaning is still necessary, especially for SO2; therefore, it is worth mentioning that the addition of paper mill sludge reduced the mercury concentration in the flue gas to limits acceptable in most EU countries. The analysis of ash after combustion showed that magnesium, potassium, calcium, chromium, copper, zinc, arsenic, and lead remained mostly in the ash after combustion, while all cadmium from all fuels used was transferred into the flue gas together with a substantial part of chlorine and mercury. The pellets containing both sewage and paper mill sludge can be used as an environmentally friendly alternative fuel for fluidised bed combustion. The levelized cost of this alternative fuel is at the same current price level as lignite.

The hot pressing parameters and fiber ratio have an important influence on the dielectric properties of aramid insulating paper. In order to deeply explore its influence and the mechanism behind it, aramid insulating papers were made with different hot pressing temperatures and pressures as well as fiber ratios. Its tightness, dielectric constant, and AC breakdown strength were tested, and its microstructure was analyzed by scanning electron microscopy. It was found that with an increase in hot pressing temperature, pressure, and fibrid content, the overall dielectric constant of the insulating paper showed a slight upward trend, while the tightness and AC breakdown strength continued to increase. Hot pressing temperature and pressure have a synergistic effect on the dielectric properties of insulating paper. The effects of these two parameters on the dielectric properties of insulating paper are similar, while the AC breakdown strength is greatly affected by the fiber ratio. In this paper, the influence mechanism by which the microstructure and fiber crystallinity of insulating paper is affected in the hot pressing process is discussed.

Wind energy is going to be the leading renewable source of the next decades [...]

Recently, as the use of wearable devices and the demand for eco-friendly energy have increased, many studies have been conducted on triboelectric nanogenerators (TENGs), which can economically harvest energy. Paper is considered a promising substrate and frame material that can be used to manufacture self-powered TENGs, owing to its flexibility, low cost, and accessibility. Herein, we present a sandwich-structured foldable paper-based TENG (FP-TENG) that comprises flexible materials and uses paper as a substrate. The FP-TENG can generate up to 572 mW/m2 of power via contact–separation of the triboelectric electrified body at the top and bottom. With more folds of the FP-TENG, the triboelectric cross-sectional area increases, and, thus, the electrical output increases. In addition, the proposed TENG exhibits excellent durability without signal degradation under 5000 cycles of repeated pushing motions. To demonstrate its practicality, the FP-TENG was manufactured in the form of a wristwatch Velcro and connected to an electronic watch panel to supply power. Various deformations are possible with origami, and they can drive wristwatches through external forces. Therefore, the FP-TENG is expected to be utilized as a sustainable and promising eco-friendly energy source for small electronic devices.

The pulp and paper industry is recognized as a well-established sector, which throughout its process, generates a vast amount of waste streams with the capacity to be valorized. Typically, these residues are burned for energy purposes, but their use as substrates for biological processes could be a more efficient and sustainable alternative. With this aim, it is essential to identify and characterize each type of waste to determine its biotechnological potential. In this context, this research highlights possible alternatives with lower environmental impact and higher revenues. The bio-based pathway should be a promising alternative for the valorization of pulp and paper industry wastes, in particular for bioproduct production such as bioethanol, polyhydroxyalkanoates (PHA), and biogas. This article focuses on state of the art regarding the identification and characterization of these wastes, their main applied deconstruction technologies and the valorization pathways reported for the production of the abovementioned bioproducts.

Generally, impregnation of solid insulation is performed to increase the dielectric strength and reduce the dielectric losses of solid insulants. This increase in dielectric strength depends on the oil’s diffusion and dielectric properties. This paper investigates the diffusion behavior of mineral oil and ester fluids (synthetic, natural, and mixed) to understand the influence of oil diffusion on paper breakdown voltage. To better understand this phenomenal influence, cellulose insulation paper of different thicknesses has been considered. Wetting characteristics of various oil-paper insulation systems were investigated with and without thermal stressing. Thermal aging was carried out as per modified ASTM D1934 at 110 °C, 140 °C, 160 °C, and 185 °C respectively for 2 weeks. The wetting characteristics and influence of different oils on paper breakdown voltage were explicitly reported. It is inferred that paper wetting characteristics are attributable to the type of oil, the thickness of paper, and the aging factor of oil-paper insulation. Importantly, the increase in paper dielectric strength and diffusion behavior for ester fluids is found to be superior to that of the mineral insulating oils.

The recovery and utilisation of industrial excess heat has been identified as an important contribution for energy efficiency by reducing primary energy demand. Previous works, based on top-down studies for a few sectors, or regional case studies estimated the overall availability of industrial excess heat. A more detailed analysis is required to allow the estimation of potentials for specific heat recovery technologies, particularly regarding excess heat temperature profiles. This work combines process integration methods and regression analysis to obtain cogeneration targets, detailed excess heat temperature profiles and estimations of electricity generation potentials from low and medium temperature excess heat. The work is based on the use of excess heat temperature (XHT) signatures for individual sites and regression analysis using publicly available data, obtaining estimations of the technical potential for electricity generation from low and medium temperature excess heat (60–140 °C) for the whole Swedish kraft pulp and paper industry. The results show a technical potential to increase the electricity production at kraft mills in Sweden by 10 to 13%, depending on the level of process integration considered, and a lower availability of excess heat than previously estimated in studies for the sector. The approach used could be adapted and applied in other sectors and regions, increasing the level of detail at which industrial excess heat estimations are obtained when compared to previous studies.

Thermal stress and moisture absorption can cause a synergetic negative impact on kraft paper. Among various approaches for improving the dielectric properties of kraft paper, nanotechnology has had promising results. However, the hydrophilicity of most metal oxide nanoparticles renders nanomodified kraft paper more vulnerable to thermal stress and moisture, thereby inducing degradation. In nanomodified kraft paper research, the use of TiO2 nanoparticles has yielded the most promising results. The major shortfall, however, is the hydrophilicity of TiO2. This work investigated surface modifications of rutile-TiO2 nanoparticles (NPs) for improved hydrophobicity and thermal stability. Rutile-TiO2 NPs is a nontoxic metal oxide that can withstand high temperature and is stable in chemical reactions. Two cases of surfactants were used—alkyl ketene dimer (AKD) and alkenyl succinic anhydride (ASA). The intention was to increase heat resistance and reduce the surface free energy of the rutile-TiO2 NPs. The impacts of the surface modifiers on the rutile-TiO2 NPs were characterised using FT-IR, muffle furnace, analytical weight balance, and TGA. It was discovered that new functional groups were formed on the modified NPs examined through FT-IR spectra. This indicates new chemical bonds, introduced through the surface modification. The unmodified rutile-TiO2 NPs absorbed moisture, increasing their mass by 3.88%, compared with the modified nanoparticles, which released moisture instead. TGA analysis revealed that AKD- and ASA-modified rutile-TiO2 needed higher temperatures than the unmodified rutile-TiO2 to markedly decompose. AKD, however, gave better performance than ASA in that regard. As an example, those modified with 5% AKD sustained a 45% higher temperature than the pure TiO2 nanoparticles. Furthermore, in both cases of the surfactants, the higher the percent of surfactant content was, the more thermally stable the nanoparticles became. This work demonstrates the possibility of fabricating rutile-TiO2 NPs to give improved hydrophobicity and thermal stability for possible dielectric applications such as in kraft paper for power transformer insulation.

The accuracy of a predictive system is critical for predictive maintenance and to support the right decisions at the right times. Statistical models, such as ARIMA and SARIMA, are unable to describe the stochastic nature of the data. Neural networks, such as long short-term memory (LSTM) and the gated recurrent unit (GRU), are good predictors for univariate and multivariate data. The present paper describes a case study where the performances of long short-term memory and gated recurrent units are compared, based on different hyperparameters. In general, gated recurrent units exhibit better performance, based on a case study on pulp paper presses. The final result demonstrates that, to maximize the equipment availability, gated recurrent units, as demonstrated in the paper, are the best options.

In this paper, the combustion behavior of low rank coal and its product after hydrothermal carbonization with paper sludge hydrochar were studied. The Raman technique was used to compare the structural differences between raw coal and the product. Thermogravimetric analysis was employed to conduct experiments of single sample and their mixtures with different proportions at a heating rate of 20 °C/min, the activation energy of chemical reactions was calculated. The results showed that upgraded product had higher carbon ordering degree than raw coal and the ignition temperature and burnout temperature of the product were advanced. Compared with raw coal, the combustion characteristic parameters C and S of the product were higher, indicating that its combustibility was better. As for the mixture, when the paper sludge hydrochar ratio was not more than 10%, the mixed fuel combustion curve was still similar to coal curve. After the paper sludge hydrochar ratio exceeded 10%, the activation energy of the mixed combustion reaction of paper sludge hydrochar and upgraded coal was lower than that of raw coal and paper sludge hydrochar. These results indicated that the mixture of upgraded coal and paper sludge hydrochar as mixed fuel was a better option.

Forecasting has extreme importance in industry due to the numerous competitive advantages that it provides, allowing to foresee what might happen and adjust management decisions accordingly. Industries increasingly use sensors, which allow for large-scale data collection. Big datasets enable training, testing and application of complex predictive algorithms based on machine learning models. The present paper focuses on predicting values from sensors installed on a pulp paper press, using data collected over three years. The variables analyzed are electric current, pressure, temperature, torque, oil level and velocity. The results of XGBoost and artificial neural networks, with different feature vectors, are compared. They show that it is possible to predict sensor data in the long term and thus predict the asset’s behaviour several days in advance.

The paper reports the results of a comparative assessment concerned with the effectiveness of identifying the basic forms of partial discharges (PD) measured by the acoustic emission technique (AE), carried out by application of selected machine learning methods. As part of the re-search, the identification involved AE signals registered in laboratory conditions for eight basic classes of PDs that occur in paper-oil insulation systems of high-voltage power equipment. On the basis of acoustic signals emitted by PDs and by application of the frequency descriptor that took the form of a signal power density spectrum (PSD), the assessment involved the possibility of identifying individual types of PD by the analyzed classification algorithms. As part of the research, the results obtained with the use of five independent classification mechanisms were analyzed, namely: k-Nearest Neighbors method (kNN), Naive Bayes Classification, Support Vector Machine (SVM), Random Forests and Probabilistic Neural Network (PNN). The best results were achieved using the SVM classification tuned with polynomial core, which obtained 100% accuracy. Similar results were achieved with the kNN classifier. Random Forests and Naïve Bayes obtained high accuracy over 97%. Throughout the study, identification algorithms with the highest effectiveness in identifying specific forms of PD were established.

A helium (He) dielectric barrier discharge plasma jet (DBD jet) was used for the first time for treating graphite foil as the current collector of a paper-based fluidic aluminum-air battery. The main purpose was to improve the distribution of the catalyst layer through modification and functionalization of the graphite foil surface. The plasma functionalized the graphite foil surface to enhance the wettability where the more hydroxyl could be observed from XPS results. The 30 s-He DBD jet treatment on the graphite foil significantly improved the battery performance. The best current density of 85.6 mA/cm2 and power density of 40.98 mW/cm2 were achieved. The energy density was also improved to 720 Wh/kg.

As a part of our research in the field of thermochemical energy storage, this study aims to investigate the potential of three fly ash samples derived from the fluidized bed reactors of three different pulp and paper plants in Austria for their use as thermochemical energy (TCES) and CO2 storage materials. The selected samples were analyzed by different physical and chemical analytical techniques such as X-ray fluorescence spectroscopy (XRF), X-ray diffraction (XRD), particle size distribution (PSD), scanning electron microscopy (SEM), inductively coupled plasma atomic emission spectroscopy (ICP-OES), and simultaneous thermal analysis (STA) under different atmospheres (N2, CO2, and H2O/CO2). To evaluate the environmental impact, leaching tests were also performed. The amount of CaO as a promising candidate for TCES was verified by XRF analysis, which was in the range of 25–63% (w/w). XRD results indicate that the CaO lies as free lime (3–32%), calcite (21–29%), and silicate in all fly ash samples. The results of STA show that all fly ash samples could fulfill the requirements for TCES (i.e., charging and discharging). A cycling stability test of three cycles was demonstrated for all samples which indicates a reduction of conversion in the first three reaction cycles. The energy content of the examined samples was up to 504 kJ/kg according to the STA results. More energy (~1090 kJ/kg) in the first discharging step in the CO2/H2O atmosphere could be released through two kinds of fly ash samples due to the already existing free lime (CaO) in those samples. The CO2 storage capacity of these fly ash samples ranged between 18 and 110 kg per ton of fly ash, based on the direct and dry method. The leaching tests showed that all heavy metals were below the limit values of the Austrian landfill ordinance. It is viable to say that the valorization of fly ash from the pulp and paper industries via TCES and CO2 storage is plausible. However, further investigations such as cycling stability improvement, system integration and a life cycle assessment (LCA) still need to be conducted.

The 55th International Universities Power Engineering Conference (UPEC 2020) has been held on 1–4 September 2020 in the Virtual Conference mode because of the limitations due to the pandemics, hosted by Politecnico di Torino, Torino, Italy [...]

Although there are opportunities to reduce electrical energy demand in unit processes of mechanical pulp-based paper and paperboard production, this may not be financially beneficial. This is generally because energy optimization opportunities connected to reduced refiner electricity demand in mechanical pulping systems also results in less steam available for the drying of the paper. As modern high consistency refiner systems produce approximately one ton of steam for each MWh of electricity when producing one ton of pulp, a reduction in electric energy demand leads to increased fuel demand in steam boilers to compensate for the steam shortage. In this study, we investigated what the financial and environmental situation would look like if we were to expand the system border from a paper mill to a larger system consisting of a mechanical pulp-based paper or paperboard mill, a district heating system with an incineration boiler and a chemical pulp mill. Mechanical pulp production has a wood to product yield of >90%, a high electric energy demand to separate woodchips to pulp and is a net producer of heat and steam while chemical pulp-based production has a wood to product yield of 50%, a low electric energy demand and is a net heat and electricity producer due to the combustion of dissolved wood polymers. The aim of this research is to create useful and robust models of how to use excess heat from certain industry sites to cover the steam shortage in other industry sites by means of utilizing and optimizing the district heating systems connecting these sites. For this purpose, we used a simulation tool which dynamically allows us to evaluate different scenarios. Our results shows that there is great potential to reduce both carbon dioxide emissions and production costs for industry sites and society by means of these tools.

The article presents issues related to the aging behavior of oil-paper insulations in transformers using different oil- and ester-based insulating fluids. Despite numerous conducted studies on the subject of oil-paper aging, the use of new insulating fluids is creating open questions. In addition, new liquids such as synthetic and natural esters, as well as oil of the newest generation, are being used. Furthermore, there is still little research on the formation of aging markers with this form of the dielectric. For this reason, in this contribution, oil-paper insulations with mineral oil-based insulating fluids, natural and synthetic esters, as well as oil from natural gas, are aged thermally accelerated at 130 °C over a duration of 15 weeks, by considering two cases of free-breathing and hermetically sealed transformers. Therefore, various aging markers are investigated to allow a condition assessment. The results show that differences exist between the fluids and design of the transformer, as in the aging rate of the paper and the formation of aging markers in the insulating liquid such as acids. These findings can be used to improve asset management strategies by a more precise determination of the aging state depending on the transformer type as well as the type of insulating fluid.

The aim of the work was to prepare and test a paper-oil insulation system according to the recommendations of CIGRE (Conseil International des Grands Réseaux Électriques) with the parameters X = 50% and Y = 30%. Pressboard was moistened to a water content of (5.0 ± 0.2) wt.% The loss tangent was measured using a DIRANA meter (FDS-PDC dielectric response analyzer) in the frequency range 10−4 Hz–5000 Hz for 6 temperatures from 293.15 K to 333.15 K with a step of 8 K. The waveforms simulated by the DIRANA software were fitted to the experimental dependence of the loss tangent. The fitting process was performed using two methods. In the first method, the measuring temperature value as well as X and Y values were entered into the software. The estimated moisture content of the insulation varied from about 1.4 to about 5.2 wt.%. The average value of moisture content was (3.73 ± 1.11) wt.%. In the second method, only the measuring temperature value was entered into the software. This improved the quality of matching. The estimated average moisture content was (5.83 ± 0.25) wt.%. It was found that the dimensions of the oil channel clearly affected the quality of the fitting process. By not taking into consideration real values of oil channel, the quality of the moisture content estimation was significantly improved.

Hydrothermal carbonization (HTC) of low quality, wet biogenic residues into intermediate bioenergy carriers can potentially contribute to a more flexible and stable renewable energy system and reduce environmental impacts compared to current residue disposal practices. This study quantifies the environmental impacts via life cycle assessment (LCA) of a novel hydrothermal process for the treatment on an industrial scale of application of three wet biogenic residues (paper bio-sludge, olive pomace, and orange peel) into bioenergy carriers, i.e., solid pellets and biogas. A comprehensive attributional cradle-to-gate life cycle assessment (LCA) was conducted; the life cycle impact assessment (LCIA) utilised the ReCiPe impact assessment method. A selection of 10 significant impact categories was prioritised. Reliability of this categorization was also ensured through a sensitivity analysis carried out using Monte Carlo simulation. Climate change, particulate matter formation and terrestrial acidification impact categories showed the highest reliability, while for freshwater ecotoxicity and freshwater eutrophication impact categories in the study suggest the need for more robust data and further investigation. The climate change impact category presents the following values, as kg CO2eq/tresidue: pulp and paper bio-sludge (PPB), 17.9; olive pomace (OP), −1290; orange peel (ORP), −1301. The LCA study compared electricity yields of the hydrothermal treatment process with conventional treatment processes for each of the target residue streams. The environmental performance of the proposed hydrothermal treatment benefits significantly from the combination of intermediate bioenergy carriers (pellets) from the solid fraction with biogas production from the liquid fraction. Avoided emissions due to the heat recovery provide further environmental benefits. The LCIA results show that the carbon footprint of the F-CUBED production system, as kgCO2eq/kWhe, accounts for –4.56, −0.63, and −0.25 for paper bio-sludge, olive pomace and orange peel, respectively.

Co-absorption of NO2 and SO2 from flue gases, in combination with the enhanced oxidation of NO by ClO2(g), is studied for three different flue gas sources: a medium sized waste-to-heat plant; the kraft recovery boiler of a pulp and paper mill; and a cruise ship. Process modeling results are used to present the technical potential for each site together with cost estimation and optimization using a bottom-up approach. A process set-up is proposed for each site together with equipment sizing and resulting flows of process fluids. The simulation results, supported by experimental results, show that removal rates equal to or greater than current best available technologies are achievable with more than 90% of NOx and 99% of SO2 removed from the flue gas. The resulting cost of removing both NOx and SO2 from the flue gases is 2100 €/ton for the waste-to-heat plant, 800 €/ton for the cruise ship and 3900 €/ton for the recovery boiler. The cost estimation show that the consumption and cost of chemical additives will play a decisive role in the economic feasibility of the investigated concept, between 50% and 90% of the total cost per ton acid gas removed.

Ocean thermal energy conversion (OTEC) aims to use the temperature difference between surface and deep seawater to generate electricity and (possibly) freshwater [...]

A converter transformer is important primary equipment in a DC transmission project. The voltage on the valve side winding is complex when the equipment is running, including DC, AC, and AC–DC combined voltage. The insulation structure of the valve side winding of a converter transformer is an oil-paper insulation structure, which may have a variety of defects in the manufacturing stage and daily use, resulting in partial discharge. Therefore, it is the key to studying the partial discharge characteristics and mechanism of oil-paper insulation under AC–DC combined voltage. In this paper, we build a two-dimensional air gap model of oil-paper-insulated pressboard considering the actual particles and actual reaction based on the fluid model. The characteristics and evolution mechanism of partial discharge (PD) in pressboard under different AC/DC combined voltages are studied by numerical simulation. The results show that when the DC component increases, the polarity effect of partial discharge is more obvious, while the potential and discharge intensity in the air gap decrease. Further analysis revealed that the DC component in the combined voltage accumulated a large number of surface charges on the surface of the air gap, and the space charge distribution was more uniform and dispersed, which generated an electric field with opposite polarity to the DC component in the air gap and, then, inhibited the development of local discharge in the paperboard. The results of the simulation are consistent with the previous experimental phenomena, and the mechanism analysis of the simulation results also verifies the previous analysis on the mechanism of experimental phenomena. This will lay a theoretical foundation for the further study of partial discharge phenomenon of oil-paper insulation structures in practical operation in the future.

The mechanical loads that gas diffusion layers (GDLs) withstand in polymer electrolyte membrane fuel cell (PEMFC) stacks are sensitive to the assembly and working conditions. The mechanical properties of GDLs mostly depend on their composition materials, microstructural characteristics, operation conditions, etc. An accurate and comprehensive understanding of the mechanical performance of GDLs is significant for predicting the stress distribution and improving the assembly technology of PEMFC stacks. This study presented a novel 3-D nonlinear and orthotropic constitutive model of a carbon paper GDL to represent the material stiffness matrix with its compressive, tensile, and shear properties. Numerical simulations were performed based on the 3-D constitutive model, and the proposed 3-D model was validated against the experimental data reported previously. It is found that the simulation results of the 3-D constitutive model show a good agreement with the experimental results. Besides, the novel 3-D nonlinear and orthotropic model was applied in the overall stress simulation of a simplified PEMFC unit cell, compared to a conventional 3-D linear and isotropic model, and the simulation results of the two models show a significant difference.

The widely recognised Energiewende, (“energy transition”) in Germany has lost its original momentum. We therefore address the question of how the transition process to a new energy system can be reignited. To do so, we developed the “5Ds approach”, which lays the groundwork for a process analysis and the identification of important catalysts and barriers. Focusing on the five major fields required for the energy transition, we analyse the effects of: (1) Decarbonisation: How can efficiency and renewable energies be expanded successfully? (2) Digitalisation: Which digital solutions facilitate this conversion and would be suitable as sustainable business models? (3) Decentralisation: How can potential decentralised energy and efficiency opportunities be developed? (4) Democratisation: How can participation be strengthened in order to foster acceptance (and prevent “yellow vest” protests, etc.)? (5) Diversification of service: Which services can make significant contributions in the context of flexible power generation, demand-side management, storage and grids? Our paper comes to the conclusion that German policy efforts in the “5D” fields have been implemented very differently. Particularly with regard to democratisation, the opportunities for genuine participation among the different social actors must be further strengthened to get the Energiewende back on track. New market models are needed to meet the challenges of the energy transition and to increase the performance of “5D” through economic incentives.

Power transformers are one of the most expensive and important equipment in the power system. Significant differences exist in the insulation lifespan of transformers that have been in operation for more than 20 years, and using identical maintenance or scrapping methods may result in significant economic losses. However, most existing transformer life assessment methods only consider the impact of moisture content on the life decay rate without considering the impact of oil circulation cooling modes, which leads to some evaluation errors. In this study, we established a new transformer life assessment method that considers the influence of moisture content and oil circulation cooling modes, which is more accurate than most life assessment methods. Then, the proposed life evaluation method was validated on the on-site transformers, demonstrating its accuracy and effectiveness. The novelty of this study is that it establishes a new on-site transformer life assessment method that considers the comprehensive effect of moisture content and oil circulation cooling mode, which helps to evaluate the remaining lifespan of power transformers more accurately and thus extends the transformer lifespan systematically.

Valorization of industrial low-value side-streams are of great interest, contributing to boosts in the circular economy. In this context, lignin side-streams of the pulp and paper industry were oxypropylated to produce biobased polyols and tested in the synthesis of rigid polyurethane (RPU) foams. E. globulus lignins, namely a lignin isolated from an industrial Kraft black liquor and depolymerized lignins obtained as by-products of an oxidation process, were used. RPU foams, synthesized with 100% lignin-based polyols and using a 1.1 NCO/OH ratio, were characterized concerning apparent density, morphology, thermal conductivity, thermal stability, and heat release rate (HRR). Foams containing the lignin-based polyols presented densities varying from 44.7 to 112.2 kg/m3 and thermal conductivity in the range of 37.2–49.0 mW/mK. For the reference foam (sample produced with 100% wt. Daltofoam TP 32015 polyol), values of 70.9 kg/m3 and 41.1 mW/mK were obtained, respectively. The achieved results point out the viability of using the generated lignin-based polyols at 100% content in RPU foams, mainly when depolymerized lignins are used. Moreover, fire retardancy was favored when the lignin-based polyols were introduced. The proposed strategies can contribute to establishing the integrated pulp and paper biorefinery concept where material synthesis (polyols and RPU foams) can be combined with chemical production (vanillin and syringaldehyde).

The reference characteristics of complex permittivity of the transformers insulation solid component were determined for use in the precise diagnostics of the power transformers insulation state. The solid component is a composite of cellulose, insulating oil and water nanoparticles. Measurements were made in the frequency range from 10−4 Hz to 5000 Hz at temperatures from 293.15 to 333.15 K. Uncertainty of temperature measurements was less than ±0.01 K. Pressboard impregnated with insulating oil with a water content of (5.0 ± 0.2) by weight moistened in a manner maximally similar to the moistening process in power transformers was investigated. It was found that there are two stages of changes in permittivity and imaginary permittivity components, occurring for low and high frequency. As the temperature increases, the frequency dependencies of the permittivity and imaginary permittivity component shifts to the higher frequency region. This phenomenon is related to the change of relaxation time with the increase in temperature. The values of relaxation time activation energies of the permittivity ΔWτε′ ≈ (0.827 ± 0.0094) eV and the imaginary permittivity component ΔWτε″ = 0.883 eV were determined. It was found that Cole-Cole charts for the first stage are asymmetric and similar to those described by the Dawidson–Cole relaxation. For stage two, the charts are arc-shaped, corresponding to the Cole-Cole relaxation. It has been established that in the moistened pressboard impregnated with insulating oil, there is an additional polarization mechanism associated with the occurrence of water in the form of nanodrops and the tunneling of electrons between them.

Most power transformers are oil-immersed transformers for which its insulation system consists of oil and cellulosic solid. The insulation liquid impregnates the solid-covering air spaces, which improves the efficiency of the insulation system. Not only does the oil ensure electrical insulation but it also works as coolants transferring the heat generated during transformer operation to the exterior of the transformer. Throughout normal operation conditions, transformers experience multiple stresses that degrade their insulation. Since the lifetime of oil-immersed transformers is defined mainly by the state of the insulation paper, it is critical to understand the behavior and degradation mechanisms of new insulation systems that try to overcome the drawbacks of mineral oil as well as to improve power transformer performances. The current increased prevalence of the nonlinear loads additionally stresses power transformers, which generates their premature ageing or even failure. Consequently, new materials and assessment methods are required to guarantee the suitable management of power transformer populations. In this Special Issue “Experimental and Numerical Analysis of Thermal Ageing in Power Transformers”, four papers have been published. The guest editor also describes briefly some challenges involved beyond the coverage of this Special Issue.

Cellulose particles are among the aging products of the insulating paper that are used in power transformers. Too many cellulose particles can cause transformer accidents. Traditional research and detection methods that are used for this problem generally focus on the number and length information of cellulose particles, and it is usually difficult to quantitatively describe the spatial shape of cellulose particles. However, the shape of cellulose particles is also one of the factors affecting the safety of transformer insulation. In this paper, we successfully extracted quantitative information of the spatial shape of cellulose particles in transformer oil using an image processing technique and the transport of intensity equation, providing a new novel approach for the study and detection of the shape of cellulose particles in transformer oil.

The life expectancy of power transformers is primarily determined by the integrity of the insulating oil and cellulose paper between the conductor turns, phases and phase to earth. During the course of their in-service lifetime, the solid insulating system of windings is contingent on long-standing ageing and decomposition. The decomposition of the cellulose paper insulation is strikingly grievous, as it reduces the tensile strength of the cellulose paper and can trigger premature failure. The latter can trigger premature failure, and to realize at which point during the operational life this may occur is a daunting task. Various methods of estimating the DP have been proposed in the literature; however, these methods yield different results, making it difficult to accurately estimate a reliable DP. In this work, a novel approach based on the Feedforward Backpropagation Artificial Neural Network has been proposed to predict the amount of DP in transformer cellulose insulation. Presently, no ANN model has been proposed to predict the remaining DP using 2FAL concentration. A databank comprising 100 data sets—70 for training and 30 for testing—is used to develop the proposed ANN using 2-furaldehyde (2FAL) as an input and DP as an output. The proposed model yields a correlation coefficient of 0.958 for training, 0.915 for validation, 0.996 for testing and an overall correlation of 0.958 for the model.

The paper presents the results of laboratory tests regarding the impact of accelerated thermal ageing of cellulose–aramid insulation samples saturated with electrical-insulating synthetic ester on the polarization and depolarization current characteristics being analyzed in the time domain. In the tests, electro-technical paper from DuPontTM was used, commercially designated as NOMEX®910. Laboratory-accelerated ageing consisted of heating with air a supply of samples of not-impregnated cellulose–aramid insulation for a specified time at specified temperatures. The temperatures and the warming time were selected so as to faithfully represent the degree of the thermal degradation of the cellulose fibers that takes place during normal operation of the material in power transformers. To determine the described impact of the ageing process in the insulation samples on the dielectric properties, the Polarization and Depolarization Method was applied. In the measurements, the MIC-15k1 high resistance meter from SONEL S.A. was used.

Functional materials, in the combination of lignocelluloses, known as natural fibers, with oxide materials, can result in cultivating functional properties such as flexibility, relativity good electrical conduction, good electrical charge storage capacity, and tunable electric permittivity. This study presents the morphological, dielectric, and impedance properties of lignocellulose–lead oxide (LC/PbO2) composite sheets electrodeposited with silver metallic nanoparticles for various time spans. The uncoated samples show a rather simple behavior where the impedance data fit well to the two-system model with different relaxation times. On the other side, the impedance spectra of the electrodeposited sample have varying features, which mainly depend upon the deposition thickness of the Ag particles. The common feature is the drift of conductive species, as seen from the straight-line behavior in the Nyquist plots, which were fitted using a Warburg element in the equivalent circuit model.

The use of nanofluids as dielectric liquids for transformer insulation has been widely investigated during the last decade. A number of authors have performed extensive studies on liquids produced from different types of nanoparticles and base fluids, providing evidence of their good dielectric properties. Nevertheless, nanodielectric fluids are still at the research stage, and they are far from being a solution that can be applied to real transformers. One of the aspects that might be clarified is their compatibility with the rest of the materials present in the transformer and their behavior throughout the life of the equipment. This paper studies the aging process of cellulose impregnated with an ester-based nanofluid and compares it with the process that takes place when the impregnation liquid is a natural ester. Accelerated aging experiments were performed, and physical and chemical characterization of the process with several analytical techniques was carried out. The mechanical degradation of the cellulose was studied in terms of tensile strength, and the evolution of moisture in the paper and oil was monitored throughout the aging process. The study was completed with FTIR and XPS tests aimed at studying the chemical changes of the materials during the aging process. The experimental results suggest that the degradation rate of the cellulose is not significantly affected by the presence of nanoparticles. However, the XPS study revealed that the chemical reactions involved in the degradation processes of both types of insulation might differ. Several mechanisms are proposed in this work.

HV bushings are an important part of the equipment of large power transformers, responsible for their many serious (including catastrophic) failures. Their proper exploitation needs to apply correct and reliable diagnostics, e.g., the use of dielectric response methods, that take into account their specific construction and working conditions. In this article, based on laboratory tests carried out on a real bushing, it has been shown that the significant temperature distribution within its core significantly affects the shape of the dielectric response of its insulation; therefore, the approach to its modeling should be changed. Hence, a new method for interpreting the results, using the so-called the 2XY model, is proposed. Subsequently, based on the measurements made on the insulators in operation, a new modeling method was verified. In conclusion, it can be stated that the 2XY model significantly improves the reliability of the dielectric response analysis, which should be confirmed in the future by tests on withdrawn and revised insulators.

The Kingdom of Saudi Arabia is experiencing a surge in electricity demand, with power generation increasing 4 times in 25 years from 1990 to 2014. Despite the abundant primary renewable energy sources, the country has overlooked them in the past in national energy policies. However, in recent years, renewable energy has become a part of the Kingdom of Saudi Arabia’s energy conservation policy due to climate changes, technological progress, economies of scale, and increased competitiveness in supply chains. The Saudi government has created the King Abdullah City for Atomic and Renewable Energy (KACARE) to develop national strategies for effectively utilizing renewable and nuclear energy. This paper reviews the current state of the art of the renewable energy technologies available on the market and evaluates the installation of renewable energy plants near Saudi Arabia’s East Coast for a new town, focusing on technical rather than economic aspects. The paper provides a wide review of the possible technical solutions to exploit the producibility of different renewable sources, considering the challenging climate conditions typical of desert areas. The analysis of a real case study shows a high availability of wind and solar irradiance that allow a net energy production of 354 and 129 GWh, respectively. In addition, the comparison between a typical ground-mounted photovoltaic (PV) system and an emerging floating PV reveals that for the same installed power, occupied area, and environmental conditions, the latter has a 4% greater performance ratio due to the cooling effect of water.

Despite the pressure of carbon emissions and clean energy, coal remains the economic backbone of many developing countries due to its abundant resources and widespread distribution. The stable supply of coal is also vital for the global economy and remains irreplaceable in the future global energy structure. China has been a major contributor to annual coal output, accounting for nearly 50% worldwide since 2014. However, despite implementing intelligent coal mining technology, China’s coal mining industry still employs over 1.5 million underground miners, posing significant safety risks associated with underground mining operations. Therefore, the introduction of coal mining robots in underground mines is an urgently needed scientific and technological solution for upgrading China’s and even the world’s coal energy industry. The working face needs a shearer, hydraulic support, a scraper conveyor, and other equipment for coordination. The deep integration of intelligent technology with factors such as “humans, machines, the environment, and management” in the workplace is the core content of intelligent coal mines. This paper puts forward an advanced framework for robot technology systems in coal mining, including single robots, robotized equipment, robot crowds, and unmanned systems. The framework clarifies the common key technologies of coal mining robot research and development and the cross-integration with new technologies such as 5G, the industrial internet, big data, artificial intelligence, and digital twins to improve the autonomous and intelligent application of coal mining robots. By establishing a scientific and complete standard system for coal mining robots, we aim to achieve the customized research and development and standardized production of various types of robot. A specific analysis is conducted on the research progress of common key technologies such as the explosion-proof design, mechanical system innovation, power drive, intelligent sensing, positioning and navigation, and underground communication of coal mining robots. The current research and application status of various types of coal mining robots in China are summarized. A new direction for future coal mining robot research and development is proposed. Robotic mining systems should be promoted to enhance the overall intelligence level and efficiency of mining equipment. To develop human–machine environment-integrated robots to improve the autonomy and collaboration level of coal mining robots, the digital twinning of the entire mine robot system should be accelerated; the normalized operation level of coal mine robots should be improved; research on coal mining robots, shield support robots, and transportation robots should be performed; intelligence should be achieved in fully mechanized mining faces; and equipment shield support for fully mechanized mining faces should be provided. The practical process of implementing coal mining robotization is summarized in this paper, and the technical and engineering feasibility of the coal mining machine population is verified.

The research problem of this paper is related to numerous open questions in the field of energy, its understanding, its use, and the challenges of the energy future. After the introductory part, in which a brief historical overview of energy literacy is provided, the paper focuses on energy literacy, its emergence, and the different approaches to its definition and measurement. The paper analyzes the energy literacy of students at the Faculty of Economics in Rijeka based on their cognitive, affective, and behavioral skills. Their knowledge about energy, energy processes, and the energy efficiency of the objects they encounter on a daily basis is examined. Their personal attitudes and values are examined through various forms of personal initiatives and active participation in energy sustainability projects. Finally, the habits and behavioral patterns that the respondents have in their daily lives and their tendencies to save energy resources and find energy-efficient solutions are examined. Despite some positive findings, the current results are not satisfactory and point to the creation of adequate public policies with a particular focus on education and the role of the corrective mechanisms of the state, but also the need for joint negotiations between policy makers, regulators, scientists, representatives of civil society, and the business community. The particular contribution of this work is reflected in being the first research of its kind conducted among Croatian economics students, as well as among Croatian students in general; in the creation of a research instrument that is conceptually consistent with the findings from the existing literature, but with an original set of questions within each energy literacy skill adapted to the cultural and sociological background of the respondents; and in a kind of progress from previous research by taking into account the quantitative aspect (in addition to the qualitative) assessment of the respondents’ energy literacy.

This paper presents a current control design for stabilizing an inductive-capacitive-inductive (LCL)-filtered grid-connected inverter (GCI) system under uncertain grid impedance and distorted grid environment. To deal with the negative impact of grid impedance, LC-type grid impedance is considered in both the system model derivation and controller design process of an LCL-filtered GCI system. In addition, the integral and resonant control terms are also augmented into the system model in the synchronous reference frame to guarantee the reference tracking of zero steady-state error and good harmonic disturbance compensation of the grid-injected currents from GCI. By considering the effect of grid impedance on the control design process, an incomplete state feedback controller will be designed based on the linear-quadratic regulator (LQR) without damaging the asymptotic stabilization and robustness of the GCI system under uncertain grid impedance. By means of the closed-loop pole map evaluation, the asymptotic stability, robustness, and resonance-damping capability of the proposed current control scheme are confirmed even when all the system states are not available. In order to reduce the number of required sensors for the realization of the controller, a discrete-time current-type full-state observer is employed in this paper to estimate the system state variables with high precision. The feasibility and effectiveness of the proposed control scheme are demonstrated by the PSIM simulations and experiments by using a three-phase GCI prototype system under adverse grid conditions. The comprehensive evaluation results show that the designed control scheme maintains the stability and robustness of the LCL-filtered GCI when connecting to unexpected grids, such as harmonic distortion and L-type and LC-type grid impedances. As a result, the proposed control scheme successfully stabilizes the entire GCI system with high-quality grid-injected currents even when the GCI faces severe grid distortions and an extra grid dynamic caused by the L-type or LC-type grid impedance. Furthermore, low-order distortion harmonics come from the background grid voltages and are maintained as acceptable limits according to the IEEE Std. 1547-2003. Comparative test result with the conventional one also confirms the effectiveness of the proposed control scheme under LC-type grid impedance thanks to the consideration of LC grid impedance in the design process.

Permanent magnet motors (PMMs) have emerged as key components in numerous industrial applications due to their high efficiency, compact size, and robust performance characteristics. However, to attain optimal performance in PMM drives, accurately predicting and mitigating core losses is paramount. This paper aims to provide a comprehensive review of advancements and methodologies for enhancing the performance of PMM drives by integrating equivalent circuit models (ECMs) that account for core losses. Firstly, the significance of core losses in motor drives is underscored, alongside a survey of research endeavors dedicated to core loss reduction. Notably, emphasis is placed on mathematical models offering both swift computation and reasonable accuracy. Subsequently, the paper delves into the development of ECMs, focusing on approaches adept at capturing core loss effects across diverse operating conditions. Moreover, this paper explores the utilization of these improved ECMs in the design and control of PMMs to achieve enhanced performance. By integrating core loss considerations into design and control strategies, PMM drives can optimize efficiency, torque production, and overall system performance. In summary, this paper may consolidate the current state-of-the-art techniques for enhancing PMM performance through the integration of core-loss-aware ECMs. It highlights key research directions and opportunities for further advancements in this critical area, aiming to foster the development of more efficient and reliable PMM-based systems for a wide range of industrial applications.

With the development of global clean energy and the implementation of carbon emission reduction policies, the direct purchase of electricity by large consumers has been increasingly promoted as a special form of electricity trading. Therefore, on the basis of the completion of low-carbon emission reduction targets in each country, how to rationalize the electricity purchase by large consumers in the electricity market so as to reduce their electricity purchase costs has become the main target of attention in each country. Currently, there are fewer studies in existing research on the direct electricity purchase strategy of large consumers under the consideration of the weight of consumption responsibility and risk. Based on this, this paper constructs a dual-game model for direct electricity purchase by large consumers based on the Stackelberg game and non-cooperative game theory. The concept of value at risk is further introduced, and the optimal strategy of direct electricity purchase by large consumers is proposed. The results of this study show that when market players make decisions on the purchase and sale of electricity, power suppliers will increase their biddings to obtain the highest returns, and large consumers can reduce the transaction costs by combining the medium- and long-term market with the spot market to purchase electricity. In the choice of electricity purchase market, with the increasing risk factor, large consumers shift from the risky spot market to the less risky medium- and long-term market and option market. This paper provides a reference for the issues of power suppliers’ contract bidding and large consumers’ electricity purchase strategy in the medium- and long-term contract transactions.

The environmental/economic dispatch (EED) of power systems addresses the environmental pollution problems caused by power generation at the operational level, offering macroscopic control without requiring additional construction and remediation costs, garnering widespread attention in recent years. This paper undertakes a comprehensive review of existing EED models, categorizing them according to the control of atmospheric pollutants into total air pollutant control (TAPC) and control considering the spatial and temporal diffusion (STD) of atmospheric pollutants. In addition, various methods employed to address the EED problems, as well as the current state of research on multi-area EED models, are presented. Finally, this paper analyzes and summarizes the literature on existing EED models, highlighting the deficiencies of the current work and future research directions. Through these explorations, the authors find that controlling the EED model by considering TAPC is more suitable for general macro planning, whereas the EED model considering the STD of air pollutant emissions enables more precise and effective control. Summarizing such models and techniques is conducive to developing dispatch plans adapted to local conditions, which is significantly beneficial for public welfare and government management, promoting sustainable and environmentally friendly power system dispatch methods.

This paper introduces a new concept in transmission expansion planning based on unconventional lines, termed “smart transmission expansion planning”. Traditionally, the domains of transmission expansion planning (TEP) and transmission line design are separate entities. TEP planners typically rely on the electrical specifications of a limited set of standard conventional line designs to evaluate planning scenarios, ultimately leading to the construction of the selected candidate line. In this context, it is noted that cost-effective scenarios often diverge from meeting the technical criteria of load flow analysis. To address this discrepancy, this paper proposes an alternative approach wherein TEP is conducted based on the specific requirements of the system earmarked for expansion. The transmission expansion planner initiates the process by determining optimal line parameter values that not only meet the operational criteria but also ensure cost-effectiveness. Subsequently, a line is designed to embody these optimal parameters. A detailed comparative analysis is conducted in this study, comparing the outcomes of TEP analyses conducted with conventional lines, unconventional lines, and lines featuring optimal parameters. Through extensive load flow analysis performed under normal and all single-contingency scenarios across three distinct loading conditions (peak load, dominant load representing 60% of peak load, and light load representing 40% of peak load), the results reveal that transmission lines engineered with optimal parameters demonstrate effective operation, with fewer transmission lines required to meet identical demands compared to other approaches.