Search

To improve the thermodynamic and mechanical properties of asymmetric polyimide (PI), a method to enhance the linearity of PI by using a structural reorganization approach was designed. First, two novel diamines containing benzimidazole and benzoxazole groups, namely PADBZ and PDBOA, were constructed and synthesized. Thereafter, two new kinds of PI films (PADBZ‐PMDA and PDBOA‐PMDA) were prepared and polymerized with 1,2,4,5‐benzenetetracarboxylic anhydride (PMDA). Based on structural reorganization, PADBZ‐PMDA and PDBOA‐PMDA had repeating units of the same chemical composition and different linearity with PABZ‐BPDA and BOA‐BPDA, respectively. Comparing PADBZ‐PMDA and PABZ‐BPDA, due to the transfer in the position of benzene, PADBZ‐PMDA with high linearity showed the improved heat resistance (Tg up to 448°C), dimensional stability (CTE down to 2.3 ppm/K) and mechanical properties. PDBOA‐PMDA and BOA‐BPDA had the same situation. This study provided a unique solution to enhance the performances of PI by increasing the linearity using a structural reorganization approach. [ABSTRACT FROM AUTHOR]

The growing demand for electronic devices has induced a significant requirement for high energy density capacitors. In this investigation, we introduced small groups of cyanoethyl cellulose (CEC) into a polyimide (PI) substrate to create all organic CEC/PI composite films for high energy density capacitor applications. Due to the large dipole moment in C–CN dipoles in CEC groups, the dielectric constant of the CEC/PI-5 (5% CEC) composite increased by 26.3% to 4.31. Compared to the pristine PI film at room temperature, the breakdown field of the CEC/PI-0.5 increased by 4.7% from 502.29 to 526.1 MV m−1 and the energy storage density increased by 95% to 11.70 J cm−3. Furthermore, the CEC/PI-0.5 film exhibited an energy density of 6.39 J cm−3 with the breakdown field of 400 MV m−1 at 150 °C, which is 93.05% higher in energy densities than that of the pristine PI film. Furthermore, simulation results indicate that CEC groups can introduce deep traps in the CEC/PI composite, which can inhibit charge movement in the composite and increase the breakdown field of it. In this study, it was found that by adding small amount of CEC polar group in PI film, the high temperature energy density of CEC/PI composite materials was significantly improved. This study not only makes a significant contribution to the development of high-temperature energy-density capacitors, but also pave a way by using small molecule polar polymers to improve the energy density of dielectric materials at high temperature. [ABSTRACT FROM AUTHOR]

Redox-active porous organic polymers (POPs) demonstrate significant potential in supercapacitors. However, their intrinsic low electrical conductivity and stacking tendencies often lead to low utilization rates of redox-active sites within their structural units. Herein, polyimide POPs (donated as PMTA) are synthesized in situ on multi-walled carbon nanotubes (MWCNTs) from tetramino-benzoquinone (TABQ) and 1,4,5,8-naphthalene tetracarboxylic dianhydride (PMDA) monomers. The strong π–π stacking interactions drive the PMTA POPs and the MWCNTs together to form a PMTA/MWCNT composite. With the assistance of MWCNTs, the stacking issue and low conductivity of PMTA POPs are well addressed, leading to the obvious activation and enhanced utilization of the redox-active groups in the PMTA POPs. PMTA/MWCNT then achieves a high capacitance of 375.2 F g−1 at 1 A g−1 as compared to the pristine PMTA POPs (5.7 F g−1) and excellent cycling stability of 89.7% after 8000 cycles at 5 A g−1. Cyclic voltammetry (CV) and in situ Fourier-Transform Infrared (FT-IR) results reveal that the electrode reactions involve the reversible structural evolution of carbonyl groups, which are activated to provide rich pseudocapacitance. Asymmetric supercapacitors (ASCs) assembled with PMTA/MWCNTs and activated carbon (AC) offer a high energy density of 15.4 Wh kg−1 at 980.4 W kg−1 and maintain a capacitance retention of 125% after 10,000 cycles at 5 A g−1, indicating their good potential for practical applications. [ABSTRACT FROM AUTHOR]

This study examined the effects of silane-modified polyimide polymer (PIS) on cement mortar. The PIS was added to replace cement in a specified ratio. Obtained results revealed that the PIS caused retardation on setting time, and accelerated UPV mostly by encapsulating unhydrated cement particles, filling pores, or reacting with C–S–H and Ca(OH)2 with shifting to Si–O vibrations. SEM results showed a good compact interface without forming considerable agglomeration and voids on the microstructure, and this improved flexural and compressive strength properties. In conclusion, silane-modified polyimide as an admixture or cement replacement can be recommended for construction industries to enhance the properties of cement mortar. [ABSTRACT FROM AUTHOR]

Aluminum‐doped ZnO (AZO) were successfully prepared on polyimide (PI) film using electrochemical deposition. Field emission scanning electron microscopy (FESEM) analysis revealed that as the aluminum concentration increased, the morphology of AZO nanostructures changed from pellets to nanorods. X‐ray photoelectron spectrometry (XPS) was employed to study the chemical states of undoped and Al‐doped ZnO on a polyimide substrate. The X‐ray diffraction (XRD) patterns of the PI/AZO nanostructures showed a polycrystalline wurtzite structure with a crystallographic orientation along the (002) plane. The XRD analysis also indicated that the average crystallite size decreased from 50.5 nm to 31.0 nm with increasing aluminum concentration (from 0.05 mM to 10 mM). Transmittance analysis revealed that with increasing aluminum concentration, the average optical transmittance in the visible region decreased from 90 % to 75 %. The aluminum concentration has a significant effect on the electrical properties of the samples, as shown by current‐voltage (I–V) and Hall measurements. Among the samples, the AZO/PI film prepared with 5 mM aluminum concentration exhibited the minimum electrical resistivity (4.14×10−2 Ω.cm), the highest carrier density (1.10×1021 cm−3) and the Hall mobility (5.40 cm2 V−1 s−1). We also discuss the possible mechanisms underlying these results compared to undoped ZnO films. This study contributes to the potential applications in flexible electronics and optoelectronics by demonstrating the tunability of AZO nanostructures on a flexible polyimide substrate through controlled aluminum doping. [ABSTRACT FROM AUTHOR]

The continuous upgrading of electronic technology has facilitated the integration and miniaturization of electronic and electrical equipment, as well as putting great pressure on the multifunctional demand for internal materials. Developing insulating materials with both low permittivity and high thermal conductivity has become imperative. This perspective focuses on polyimide (PI), which is the top material of the polymer material pyramid, discusses the characteristic parameters that affect its dielectric property and thermal conductivity. A series of basic schemes to regulate the dielectric/thermal properties of PI are summarized, revealing the bottlenecks and drawbacks of the current research. Future development trends of PIs featured low permittivity-high thermal conductivity are anticipated, and novel ideas are proposed for the development of new generation of multifunctional PIs. [ABSTRACT FROM AUTHOR]

This paper introduces a novel, cost-effective solution designed to achieve large absorption bandwidth within the THz spectrum employing a miniaturized, single-layer metamaterial structure. The designed structure features a single circular ring composed of an ohmic resistive sheet with notably higher sheet resistance than traditional metallic resonators. This distinctive design is implemented on a lossy dielectric polyimide substrate with a backing of metallic gold. Our developed absorbing structure demonstrates the capability to achieve a substantial absorption bandwidth ranging from 3.78 to 4.25 THz, maintaining a consistent absorption rate of over 90%. Moreover, we conducted an analysis to assess its absorption performance under various sheet resistance values within the top layer. Additionally, we characterized its angular stability and polarization insensitivity through oblique incident and polarization angle analysis. Finally, an RLC circuital and interference theory approach is adopted to justify its simulated results. The proposed absorber shows potential for a broad spectrum of applications, encompassing communication, imaging, and diverse integrated circuits operating within the THz band. [ABSTRACT FROM AUTHOR]

A lithium‐ion battery separator facilitates lithium‐ion transportation and prevents direct contact between the cathode and anode. Polyimide separators exhibited superior thermal stability and electrolyte wettability. In this study, carboxylated polyimide separators were prepared by electrospinning carboxyl group‐containing monomers. Polyimide separators were prepared with different content of carboxyl group‐containing monomer. Moreover, the thermal property, mechanical property, and electrochemical performance of separators were studied. The carboxylated polyimide separators exhibited lower interfacial resistance and higher ionic conductivity compared with polyimide separators. Moreover, the LiFePO4/Li half‐cell assembled using the carboxylated polyimide exhibited enhanced cycling stability and rate capability. Therefore, carboxylated polyimide separators with superior electrochemical performances are promising candidates for lithium‐ion batteries. [ABSTRACT FROM AUTHOR]

Metalized plastic current collectors (MPCCs) have shown potential in improving the energy density and safety of lithium‐ion batteries (LIBs). However, the poor mechanical strength, weak interfacial adhesion force, and surface metal corrosion have impeded the practical application of MPCCs. Here, an innovative engineering of MPCCs is proposed by incorporating halloysite nanotubes (HNTs) as fillers into polyimide (PI) polymer layer, which is further coated with two thin copper (Cu) layers. Because of the strong bonding between HNTs surface and the PI precursor, HNTs improve the mechanical strength of PI‐HNTs composite film, reinforce the interfacial adhesion force between the PI‐HNTs film and the coated Cu layer, and suppress the Cu corrosion by electrolyte. The prepared MPCCs exhibit a low mass density and only account about one‐fifth of the density of commercial Cu CCs. Furthermore, the PI‐HNTs‐Cu composite demonstrates significantly enhanced interfacial adhesion force doubled to 4 N cm−1 along with prolonged stability under electrolyte immersion and electrochemical reaction conditions, and delivers a high fracture strength of 125 MPa. LIBs assembled with MPCCs deliver a twice higher discharge capacity compared to battery with Cu CCs and reach a long‐term cycle capacity retention as high as 92.9% at 0.5 C after 500 cycles. [ABSTRACT FROM AUTHOR]

Copyright of Acta Materiae Compositae Sinica is the property of Acta Materiea Compositae Sinica Editorial Department and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

The traditional high-temperature preparation process of polyimide can cause many problems and limits the wider application in extreme conditions. An important challenge to be solved urgently is the reduction of imidization temperature. In this work, twelve kinds of polyimide films with different chain rigidity were prepared at low temperature of 200 °C, in the absence or presence of imidazole used as the catalyst. The molecular rigidity and free volume were theoretically calculated, and relationship between structure and properties were systematically studied. The results show that imidization reaction under low temperatures is significantly affected by the rigidity of molecular chains. The rigid structure of polyimide is not conducive to the low-temperature imidization, but this adverse effect can be eliminated by adding catalyst, resulting the notably increased imidization degree. The optical and thermal properties can be improved to a certain extent for the chemically catalyzed system, resulting in relatively higher heat resistance and thermal stability. While the mechanical performance could be determined by complicating factors, greatly different from polyimide films prepared by high temperature method. To investigate aggregation structures of films, the effect of chain rigidity and catalyst on the stacking or orientation of molecular chains was further elaborated. This work can contribute to the understanding of chemically catalyzed imidization that is rarely reported in the existing research, and will provide guidance for the low-temperature preparation of high-performance polyimides. [ABSTRACT FROM AUTHOR]

In this study, 4-biphenyl-3,5-diaminobenzoate (E- m -PDA) was synthesized by three steps using 3,5-dinitrobenzoic acid as a starting material. Two series of colorless polyimides (CPIs) PI-(1a-1d) and PI-(2a-2d) were prepared by traditional two-step polycondensation of m -phenylenediamine (m -PDA) based diamines with different pendant groups (-H, CF3, COOH and biphenyl ester) with aromatic dianhydrides BPADA and 6FDA, respectively. All of the prepared CPIs exhibited high thermal stability with 5% weight loss at temperatures ranging from 428 to 539°C in nitrogen, and glass transition temperatures (T gs) ranging from 228 to 332°C. These PI films displayed a UV-vis absorption cut-off wavelength at 338–376 nm and transparency of 76%–89% at a wavelength of 450 nm. Both series of colorless PI films also showed low birefringence values of 0.0021–0.0100. In addition, the optical retardations of these CPIs were extremely low (48–220 nm), indicating low optical anisotropy of these CPI films. Colorless PI film PI-2d prepared based on E- m -PDA and 6FDA had good comprehensive properties of low birefringence (∆ n of 0.0064), high T g (319°C) and excellent transparency (T 450 of 88%). [ABSTRACT FROM AUTHOR]

In order to improve the PI resin's processability and thermal properties, a novel diamine monomer bis(p-aminophenylethynyl)dimethylsilane was designed and synthesized by introducing silicon and alkyne groups in this paper. And a new thermosetting polyimide resin SiOPI with silicon and alkynyl structures in the main chain was prepared using 4,4′-oxobis (phthalic anhydride) (ODPA) as the dianhydride monomer with this diamine monomer. The structures of the diamine monomer and the polyimide were characterized by H nuclear magnetic resonance spectroscopy (1H NMR), Fourier transform infrared spectroscopy (FT-IR), mass spectrometry (MS), and X-ray diffraction (XRD), respectively. The incorporation of silyl groups into the PI increases the flexibility of the resin and provides good solubility and processability. The SiOPI is well soluble in DMF, DMSO and THF. The resin has a viscosity of less than 200 Pa·s at 50–88°C and has a wide processability range. By virtue of the introduction of alkyne groups, the cured polyimide forms dense reticulated structures, analogous to the benzene ring, giving the resin excellent heat resistance and mechanical property. The glass transition temperature (Tg) of SiOPI reached 367°C, and the heat loss temperature at 5% (Td5) is 540.9°C, the heat loss temperature at 10% (Td10) is 592.2°C, and the residual carbon rate at 800°C (R800°C) is 65.76% in a nitrogen atmosphere. The tensile strength of c-SiOPI is 257.6 MPa at room temperature and 232.9 MPa with a retention rate of 90.41% at 300°C, respectively. [ABSTRACT FROM AUTHOR]

Copyright of China Plastics / Zhongguo Suliao is the property of Journal Office of CHINA PLASTICS and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Air pollution containing microorganisms poses a major hazard to human health. It is critical to develop air filters that are both highly efficient for indoor use and suitable for use in industrial settings. Developing long‐lasting electrostatic force‐assisted filtration while keeping high‐temperature resistance and antibacterial qualities is still challenging. Here, centrifugal spinning is used to fabricate fiber mats consisting of polyimide with silver incorporation (PI/Ag). The electrostatic force remained over –700 V after 330 days. The strong electrostatic effect improves the filtration efficiency, resulting in a high PM0.3 removal efficiency of 99.1% with a low‐pressure drop of 103.67 Pa. The high filtration efficiency remains above 91.3% for PM0.3 after placing it for 330 days and heating it at 280 °C. The PI/Ag fiber mats also show antimicrobial properties against the E. coli (Gram‐negative) and S. aureus (Gram‐positive) with prominent bacteriostatic zones >1.2 mm. The PI/Ag fiber mat filters are expected to have great potential for multi‐scenario air filtration. [ABSTRACT FROM AUTHOR]

Relationship between the temperature of the electric field treatment (EFT) and the improvement of the effective thermal conductivity (TC) in the out‐of‐plane direction of the carbon nanofiber (CNF)/cured silicone rubber composite sheet was investigated to elucidate the appropriate operation of the EFT. Two types of silicone rubber precursors, with viscosities of 1.3 and 58 Pa∙s, were used. The effective TC gradually increased as the temperature during EFT increased from 40 to 80 °C. However, beyond 80 °C, the effective TC started to decrease and reached the same value as that of the sheet without EFT at 100 °C. This trend was observed regardless of the rubber species or CNF content. The influence of the EFT temperature was also discussed regarding the temperature dependency of the viscoelastic properties: storage modulus, loss modulus, and complex viscosity of the uncured precursor solution. When the temperatures were set at 80 °C, no significant changes were observed in the three‐viscoelastic properties for 60 min. On the other hand, a significant increase in the viscoelastic properties was observed after 10 min at 100 °C because of the start of the curing reaction, which supported the relationship between the temperature of the EFT and effective TC. [ABSTRACT FROM AUTHOR]

2D conjugated metal–organic frameworks (2D c‐MOFs) with large pore sizes and high surface areas are advantageous for adsorbing iodine species to enhance the electrochemical performance of aqueous dual‐ion batteries (ADIBs). However, most of the reported 2D c‐MOFs feature microporous structures, with few examples exhibiting mesoporous characteristics. Herein, we developed two mesoporous 2D c‐MOFs, namely PA‐TAPA−Cu‐MOF and PA‐PyTTA−Cu‐MOF, using newly designed arylimide based multitopic catechol ligands (6OH‐PA‐TAPA and 8OH‐PA‐PyTTA). Notably, PA‐TAPA−Cu‐MOF exhibits the largest pore sizes (3.9 nm) among all reported 2D c‐MOFs. Furthermore, we demonstrated that these 2D c‐MOFs can serve as promising cathode host materials for polyiodides in ADIBs for the first time. The incorporation of triphenylamine moieties in PA‐TAPA−Cu‐MOF resulted in a higher specific capacity (423.4 mAh g−1 after 100 cycles at 1.0 A g−1) and superior cycling performance, retaining 96 % capacity over 1000 cycles at 10 A g−1 compared to PA‐PyTTA−Cu‐MOF. Our comparative analysis revealed that the increased number of N anchoring sites and larger pore size in PA‐TAPA−Cu‐MOF facilitate efficient anchoring and conversion of I3−, as supported by spectroscopic electrochemistry and density functional theory calculations. [ABSTRACT FROM AUTHOR]

2D conjugated metal–organic frameworks (2D c‐MOFs) with large pore sizes and high surface areas are advantageous for adsorbing iodine species to enhance the electrochemical performance of aqueous dual‐ion batteries (ADIBs). However, most of the reported 2D c‐MOFs feature microporous structures, with few examples exhibiting mesoporous characteristics. Herein, we developed two mesoporous 2D c‐MOFs, namely PA‐TAPA−Cu‐MOF and PA‐PyTTA−Cu‐MOF, using newly designed arylimide based multitopic catechol ligands (6OH‐PA‐TAPA and 8OH‐PA‐PyTTA). Notably, PA‐TAPA−Cu‐MOF exhibits the largest pore sizes (3.9 nm) among all reported 2D c‐MOFs. Furthermore, we demonstrated that these 2D c‐MOFs can serve as promising cathode host materials for polyiodides in ADIBs for the first time. The incorporation of triphenylamine moieties in PA‐TAPA−Cu‐MOF resulted in a higher specific capacity (423.4 mAh g−1 after 100 cycles at 1.0 A g−1) and superior cycling performance, retaining 96 % capacity over 1000 cycles at 10 A g−1 compared to PA‐PyTTA−Cu‐MOF. Our comparative analysis revealed that the increased number of N anchoring sites and larger pore size in PA‐TAPA−Cu‐MOF facilitate efficient anchoring and conversion of I3−, as supported by spectroscopic electrochemistry and density functional theory calculations. [ABSTRACT FROM AUTHOR]

Aerogels are widely used as thermal insulation materials because of their high porosity and low bulk density. However, the insulation performance of aerogels is limited to a narrow temperature range. Besides, the preparation of aerogel materials with precisely controlled and complex architectures is still challenging. Here, we report 3D printed polyimide/silica aerogel particle (PI/SAP) composite aerogels for thermal insulation in a wide range of temperature with customized applications. The printability and shape fidelity of 3D printed composite aerogels is improved by adding hydrophilic SAP as a rheology modifier. The resulting PI/SAP composite aerogel exhibits excellent flame-retardant properties and thermal insulation from −50 °C to 1300 °C. Moreover, the PI/SAP composite aerogel with customized shape can be applied for battery insulation at subzero temperatures, promising to be used as customizable and stable insulating materials in a variety of complex and extreme applications. [ABSTRACT FROM AUTHOR]

Researching and manufacturing materials that possess both electromagnetic interference (EMI) shielding and infrared stealth capabilities is of great significance. Herein, an ultrathin polyimide-based nonwoven fabric with low-reflection EMI shielding/infrared stealth performance is successfully fabricated by in-situ loading of Fe3O4/Ag nanoparticles on the surface of polyimide (PI) fiber (PFA), and followed by bonding with a commercial Cu/Ni mesh. The synergistic assembly of PFA and Cu/Ni promotes the rational construction of hierarchical impedance matching, inducing electromagnetic waves (EMW) to enter the composite and be dissipated as much as possible. Meanwhile, the existence of Cu/Ni mesh on back of PFA facilitates the formation of electromagnetic resonance and destructive interference of EMW reflected from composite, leading to a lower-reflectivity (0.26) EMI shielding performance of 58 dB within 24–40 GHz at a thinner thickness (430 µm). More importantly, the fluffy PFA nonwoven fabric and metal Cu/Ni mesh endow composite with good thermal insulation and low infrared emissivity, resulting in excellent infrared stealth performance in various environments. As a result, such excellent compatibility makes it possible to become a promising defense material to be applied in military tent for preventing electromagnetic and infrared radiation. [ABSTRACT FROM AUTHOR]

Recently, PI as high-performance polymer with high glass transition temperature have been regarded as promising matrix for high-temperature dielectric nanocomposites. As such, the review aimed to summarize the influence of nanoceramic fillers on the characteristics of polyimide-based nanocomposites for high-temperature energy storage. Herein, it is worth noting that SiO2, TiO2, AlN, and BN remain favorable reinforcement materials for improving thermal stability, breakdown strength, and energy density of PI-matrix for high-temperature energy storage. Thus, as they depict the potential properties needed in high-temperature dielectrics, the authors concluded the study with challenges/recommendations for further enhancement of PI-based nanocomposites for high-temperature energy storage. [ABSTRACT FROM AUTHOR]

Thermoplastic polyimides (TPIs) can meet the requirements of advanced electronic packaging such as flexible copper clad laminate (FCCL) applied under extreme conditions, attributed to their excellent thermal stability, mechanical properties, electrical insulation and chemical resistance. With the increasing demands for electronic devices, such as applications in high‐frequency communication, it is highly desirable to develop high‐performance TPI with good thermoplasticity, thermal stability, mechanical properties and dielectric properties. However, there is a trade‐off between thermoplasticity and other properties. Herein, we introduce an effective strategy to afford TPIs with good performance by copolymerization of a diamine monomer consisted of a coplanar aromatic carbazole group and a short flexible linkage methylene group. On the one hand, short flexible linkages help improve the flexibility of polymer chains and are not too much to enable small‐scale molecular motions below Tg. On the other hand, coplanar aromatic donor groups benefit to strong charge transfer complex (CTC) interaction and π‐π stacking interaction. Based on this strategy, the resultant TPI possesses good thermoplasticity with a proper Tg of 348 °C. Meanwhile, it preserves a low coefficient thermal expansion of 48 ppm K−1, low dielectric constant/dielectric loss factor of 3.27/0.0073 at 10 GHz, and tensile strength of ca. 78 MPa. [ABSTRACT FROM AUTHOR]

Copyright of Lubrication Engineering (0254-0150) is the property of Editorial Office of LUBRICATION ENGINEERING and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Carbon-based conductive polymer composites (CPCs) have significant potential for fabricating low-cost and high-performance flexible electric heating films in deicing applications. However, the inferior high-temperature resistance and low heating power density seriously restrict their large-scale commercial application. Herein, a series of polyimide (PI)/carbon black (CB) composite electrothermal films with excellent high-temperature stability and high-power density are prepared by a simple slurry coating method. With successfully introducing the high-temperature resistance and high mechanical strength PI as polymer matrix, the PI/CB composite electrothermal films with a low percolation threshold of 10.8% have a broad operating temperature ranging from 40°C to 270°C under low applied voltages (< 60 V) at room temperature. Impressively, these PI/CB composite electrothermal films with a uniform thin thickness of 45 μm exhibit high operating temperature (> 200°C), rapid heating response speed (< 10 s), remarkable long-term working stability, and superior low-temperature operating reliability even at −30°C. The simulated deicing experiment indicates that the PI/CB composite electrothermal film dislodges an ice cube (thickness = 10 mm) within 280 s. This work not only provides a universal strategy for the design and fabrication of high-operating-temperature CPCs, but also verifies the great potential for use in deicing applications. [ABSTRACT FROM AUTHOR]

Silicon carbide (SiC) is a wide-band gap semiconductor that exceeds other semiconducting materials (except diamond) in electrical, mechanical, chemical, and radiation stability. In this paper, we report a novel approach to fabrication of SiC nano films on a Si substrate, which is based on the endotaxial growth of a SiC crystalline phase in a graphite-like carbon (GLC) matrix. GLC films were formed by carbonization of rigid rod polyimide (PI) Langmuir–Blodgett (LB) films on a Si substrate at 1000 °C in vacuum. After rapid thermal annealing of GLC films at 1100 °C and 1200 °C, new types of heterostructures SiC(10 nm)/GLC(20 nm)/Si(111) and SiC(20 nm)/GLC(15 nm)/SiC(10 nm)/Si(111) were obtained. The SiC top layer was formed due to the Si-containing gas phase present above the surface of GLC film. An advantage of the proposed method of endotaxy is that the SiC crystalline phase is formed within the volume of the GLC film of a thickness predetermined by using PI LB films with different numbers of monolayers for carbonization. This approach allows growing SiC layers close to the 2D state, which is promising for optoelectronics, photovoltaics, spintronics. [ABSTRACT FROM AUTHOR]

Titanium oxide (TiO2) coated polyimide has broad application prospects under extreme conditions. In order to obtain a high-quality ultra-thin TiO2 coating on polyimide by atomic layer deposition (ALD), the polyimide was activated by in situ oxygen plasma. It was found that a large number of polar oxygen functional groups, such as carboxyl, were generated on the surface of the activated polyimide, which can significantly promote the preparation of TiO2 coating by ALD. The nucleation and growth of TiO2 were studied by x-ray photoelectron spectroscopy monitoring and scanning electron microscopy observation. On the polyimide activated by oxygen plasma, the size of TiO2 nuclei decreased and the quantity of TiO2 nuclei increased, resulting in the growth of a highly uniform and dense TiO2 coating. This coating exhibited excellent resistance to atomic oxygen. When exposed to 3.5 × 1021 atom cm−2 atomic oxygen flux, the erosion yield of the polyimide coated with 100 ALD cycles of TiO2 was as low as 3.0 × 10−25 cm3/atom, which is one order less than that of the standard POLYIMIDE-ref Kapton® film. [ABSTRACT FROM AUTHOR]

Polyimide (PI) has good mechanical properties and thermal stability, while high coefficient (COF) and wear rate limit its wide application. In order to endow PI with better friction and wear resistance, Mo2Ti2C3 MXene was used as solid lubricant to prepare Mo2Ti2C3/PI nanocomposites with different content of Mo2Ti2C3. The effect of the amount of Mo2Ti2C3 on the tribological behavior of PI was explored and the tribological mechanism was also analyzed Tribological tests showed that at 1.2 wt% of Mo2Ti2C3 addition, the composite material demonstrated superior friction and wear resistance, exhibiting a 19.9% decrease in the COF and a 79.7% decrease in the wear rate compared to single PI due to the good self‐lubricating properties of Mo2Ti2C3 MXene. Moreover, Mo2Ti2C3 can also effectively assist PI to form sleek transfer films without interruption or gaps on the steel balls, resulting in a reduced friction COF and wear rate of the material. This work demonstrates that Mo2Ti2C3 MXene is an aussichtsreich additive for polymers to improve the tribological properties and broadens the applications of Mo2Ti2C3/PI composites in friction material area. Highlights: Mo2Ti2C3 significantly improves the tribological performance of polyimide.The thermal properties of Mo2Ti2C3/polyimide are enhanced by the introduction of Mo2Ti2C3.The minimum coefficient of Mo2Ti2C3/PI composites was only 0.246 at the 1.2 wt% content of Mo2Ti2C3.The wear rate of Mo2Ti2C3/PI composites was decreased by 79.7% at the 1.2 wt% addition of Mo2Ti2C3.Mo2Ti2C3 promotes the establishment of tribo‐film to protect the Mo2Ti2C3/PI composites from friction. [ABSTRACT FROM AUTHOR]

The triboelectric nanogenerator (TENG) has been considered as an effective way to convert various mechanical energies into electrical energy. However, the energy output needs continuous improvement for potential applications. In this study, triboelectric layers composed of polyimide (PI) matrix and carbon nanotube@barium titanate (CNT@BTO) nanoparticles were developed to achieve the performance enhancement through the synergistic coupling of piezoelectric and triboelectric effects as well as the microcapacitor function. To achieve the purpose, CNT@BTO nanoparticles were synthesized by the chemical vapor deposition method and then incorporated into a flexible PI triboelectric layer prepared using electrospinning technology and thermal imidization. The results showed that when the BTO content was 26 wt % and the CNT content was 2 wt %, the open-circuit voltage and short-circuit current of a TENG based on a PI/CNT@BTO nanofiber membrane reached 305 V and 104 μA, which were 3 times higher than those of a pure PI-based TENG. The TENG demonstrated sufficient power to drive small electronic devices, such as calculators, and to light up 124 commercial green LED and 18 blue COB light sources. Additionally, the TENG was integrated into a real-time temperature-sensing alarm system, showcasing its potential application in safety-related fields. The study demonstrated the feasible methods for TENGs' performance enhancement and provided potential application fields of energy-harvesting and self-powered sensing systems. [ABSTRACT FROM AUTHOR]

Copyright of Plastics Science & Technology / Suliao Ke-Ji is the property of Plastics Science & Technology Editorial Office and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Polymer Materials Science & Engineering is the property of Sichuan University, Polymer Research Institute and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

To provide polyimide (PI) with high heat resistance and ultra-low coefficient of thermal expansion (CTE) for use in flexible display substrates, a novel diamine with bisbenzimidazole and bisamide groups, namely N,N'-(1H,1'H-[5,5'-bibenzo[d]imidazole]-2,2'-diyl)bis(4-aminobenzamide) (BZBA), was designed and successfully synthesized. Several poly(benzimidazole-amide-imide) (PBIAI) films were prepared by thermal imidization with 3,3',4,4'-biphenyltetracarboxylic dianhydride (BPDA), 4,4'-oxydiphthalic anhydride (ODPA), 3,3',4,4'-benzophenonetetracarboxylic dianhydride (BTDA), and 4,4'-(hexafluoroisopropylindene)-diphthalic anhydride (6FDA), respectively. Among them, BZBA-BPDA has a high glass transition temperatures (T g = 345 °C) while achieving an extremely low coefficients of thermal expansion (CTE = 1.9 ppm K−1), meeting the processing requirements of polymer flexible substrates in OLED devices. The effects of different dianhydrides on the performance of PBIAIs were compared, providing a meaningful reference for further adjusting the PI molecular structure to meet specific requirements for industrial polymer films. [ABSTRACT FROM AUTHOR]

This work is dedicated to the development and investigation of the properties of low‐dielectric‐constant nonwoven materials obtained by electrospinning from a polyimide‐based polymer, PMDA‐ODA, which is composed of pyromellitic dianhydride (PMDA) and 4,4′‐oxydianiline (ODA). The influence of the molar mass of PMDA‐ODA on the structural, mechanical, and dielectric properties of the resulting samples has been investigated. The molar mass of the polyimide has been determined through light scattering and viscosity measurements of polyamic acid solutions. As the molar mass of PMDA‐ODA increases from 13.400 to 49.300 g/mol, the glass transition temperature of the produced nonwoven samples increases, and their tensile mechanical properties are improved. The dielectric constant of PMDA‐ODA nonwoven polyimide materials varies from 1.55 to 1.91 at a temperature of 30°C in a frequency range from 1 Hz to 1 MHz, depending on the molar mass of the polymer used. [ABSTRACT FROM AUTHOR]

Bio‐compatible strain sensors are indispensable for human monitoring devices, requiring a delicate balance of robustness, flexibility, and sensitivity. However, achieving these attributes concurrently remains a formidable challenge. This article presents a pioneering approach to fabricate three‐dimensional flexible strain sensors using laser‐induced graphene (LIG) on polyimide (PI) substrates. Through a one‐step laser direct writing (LDW) technique, durable LIG/CuSO4 composites with closed‐pore porous structures are synthesized. The integration of copper sulfate within the closed‐cell architecture of LIG establishes a resilient conducting pathway, enhancing sensitivity to deformation under tensile stress. The resulting sensor exhibits exceptional performance in monitoring a wide range of human movements, from vigorous activities to subtle oscillations and physiological signals. Notably, the sensor boasts a remarkable sensing range of up to 25% strain, coupled with a high sensitivity characterized by a gauge factor of approximately 597. Rapid response times of 175 ms and quick recovery times of 200 ms further underscore its efficiency. Moreover, the sensor demonstrates outstanding stability and durability, maintaining consistent performance over 5600 cyclic experiments. This innovative approach represents a significant advancement in bio‐compatible strain sensor technology, offering a versatile solution for diverse monitoring applications. [ABSTRACT FROM AUTHOR]

Orientation film is a key material in liquid crystal displays, and the technology of inducing liquid crystal molecular orientation through polyimide photoorientation film is widely studied. In this work, polyimide is a random copolymer synthesized from a mixture of cyclobutanetetracarboxylic dianhydride and pyromellitic dianhydride, 4,4' ‐ diaminodiphenylmethane, 3,3', 5,5'‐ tetramethylbenzidine, and Methanone, bis (4‐aminophenyl) ‐, homopolymer. In this study, we investigated the pre‐inclination of a series of photo‐crosslinked diamine structures for the polymerization of RM monomers by PSVA (Polymer Stabilized Vertical Alignment) technology, and mainly investigated the pre‐inclination of a series of light‐oriented films with different molar fraction reaction monomers polymerized on the backbone. The results show that the polymerization of 2‐(methacrylate)ethyl ester 3,5‐diaminobenzoic acid reaction monomer with 6.3% molar fraction of polyimide photooriented film achieves high pre‐tilt adjustment under low light accumulation conditions, and successfully achieves excellent optical & reliability performance. [ABSTRACT FROM AUTHOR]

The irreversible threshold voltage (Vth) shift by polyimide (PI) charging is experimentally demonstrated. The Vth of device without PI electrode is positively moved during the release. Interestingly, the shifted Vth is not recovered to initial value up to one month. The mechanism for the irreversibility is suggested. [ABSTRACT FROM AUTHOR]

The excellent electrical properties of graphene have received widespread attention. However, the difficulty of electron transfer between layers still restricts the application of graphene composite materials to a large extent. Therefore, in this study, graphene/polyimide films were subjected to a Joule heating treatment to improve the electrical conductivity of the film by ~76.85%. After multiple Joule thermal cycle treatments, the conductivity of the graphene/polyimide film still gradually increased, but the increase in amplitude tended to slow down. Finally, after eight Joule heat treatments, the conductivity of the graphene/polyimide film was improved by ~93.94%. The Joule heating treatment caused the polyimide to undergo atomic rearrangement near the interface bonded to the graphene, forming a new crystalline phase favourable for electron transport with graphene as a template. Accordingly, a model of the bilayer capacitive microstructure of graphene/polyimide was proposed. The experiment suggests that the Joule heating treatment can effectively reduce the distance between graphene electrode plates in the bilayer capacitive micro-nanostructures of graphene/polyimide and greatly increases the number of charge carriers on the electrode plates. The TEM and WAXS characterisation results imply atomic structure changes at the graphene/polyimide bonding interface. [ABSTRACT FROM AUTHOR]

As one single membrane material could not fulfill the requests of chemical stability, mechanical strength, and resistance to pollution in practical applications. Modifications of the membrane to improve its separation performance were of great significance. In this study, UV irradiation grafting modification was employed and butyl acrylate was selected as a modification monomer for polyimide membrane to improve its lipophilicity and separation efficiency in lubricant solvent recovery. And effects of monomer concentration, irradiation distance, and grafting time on the grafting results and separation properties of modified polyimide membranes were investigated. The results exhibited that modified polyimide membranes obtained an enhanced lubricant retention rate compared with raw membranes, which increased from 66.5% to 93.1%. The industrial test for 40 days proved the great stability of modified polyimide membranes. Overall, this work confirmed the good industrial utilization potential of modified polyimide membranes and offered an effective way for lubricant solvent recovery. [ABSTRACT FROM AUTHOR]

With the increasing demand for innovative electronic products, LED transparent screens are gradually entering the public eye. Polyimide (PI) materials combine high temperature resistance and high transparency, which can be used to prepare flexible copper-clad laminate substrates. The physical and chemical properties of PI materials differ from copper, such as their thermal expansion coefficients (CTEs), surface energy, etc. These differences affect the formation and stability of the interface between copper and PI films, resulting in a short life for LED transparent screens. To enhance PI-copper interfacial adhesion, aminopropyl-terminated polydimethylsiloxane (PDMS) can be used to increase the adhesive ability. Two diamine monomers with a trifluoromethyl structure and a sulfone group structure were selected in this research. Bisphenol type A diether dianhydride is a dianhydride monomer. All three of the above monomers have non−coplanar structures and flexible structural units. The adhesion and optical properties can be improved between the interface of the synthesized PI films and copper foil. PI films containing PDMS 0, 1, 3, and 5 wt% were analyzed using UV spectroscopy. The transmittance of the PI-1/3%, PI-1/5%, PI-2/3%, and PI-2/5% films were all more than 80% at 450 nm. Meanwhile, the Td 5% and Td 10% heat loss and Tg temperatures decreased gradually with the increase in PDMS. The peel adhesion of PI-copper foil was measured using a 180° peel assay. The effect of PDMS addition on peel adhesion was analyzed. PIs-3% films had the greatest peeling intensities of 0.98 N/mm and 0.85 N/mm. [ABSTRACT FROM AUTHOR]

Nitrogen-doped carbon is a major class of high-performance electrode materials for the electrochemical supercapacitor. Herein, nitrogen-doped carbon was obtained by pyrolysis to graphene-grafted polyimide precursors on carbon cloth through in situ polymerization. The morphology, structure, and electrochemical properties of flexible electrodes were investigated in detail. Scanning electron microscopy (SEM) confirmed the preparation of nitrogen-doped carbon on carbon cloth. X-ray photoelectron spectroscopy (XPS) characterization showed the doping of the N heteroatom. Flexible electrodes obtained with the optimized mass graphene delivered high specific capacitance of 669 F g−1 at 0.5 A g−1 and good cycle stability, with retention of 122.3% capacitance after 6000 cycles in a three-electrode system. These typical flexible electrodes show great potential in wearable energy storage devices. [ABSTRACT FROM AUTHOR]

The present study aims to assess the impact of alfa and date palm natural fibers as reinforcement for epoxy, vinyl ester, and polyimide polymer (Alfa-Date palm/epoxy, Alfa-Date palm/vinyl ester, and Alfa-date palm/polyimide) through a genetic approach. The study employs a genetic simulation rooted in the Weibull formalism, employing genetic operators such as selection, crossing, and mutation for a nuanced evaluation of the damage at the fibermatrix interface across the studied materials. The genetic algorithm results authentically capture the intrinsic behaviour of these materials, emphasising key mechanical properties like Young's Modulus, deformation, and stress at break. The obtained results highlight that the matrix showing the highest Young's modulus value at its fiber-matrix interface exhibits superior strength. These conclusions align with contemporary advancements in natural fiber-reinforced composite materials tailored for diverse industries and eco-friendly applications. [ABSTRACT FROM AUTHOR]

This paper investigates the properties of 100-nm ZnO thin films prepared by radio frequency (RF) sputtering technique on polyethylene terephthalate (PET) and polyimide (PI) plastic substrates using X-ray diffraction (XRD) patterns to show the proper formation of hexagonal ZnO (002) structure, with ZnO on PET plastic substrate recording higher peak and FWHM compared to ZnO on PI plastic substrate. AFM reveals smooth surface morphologies on both substrates with a root-mean-square (RMS) roughness of below 10 nm. Optical transmittance measures values exceeding 80% in the visible and infrared (IR) regions on each substrate. ZnO on PET records 3.33 eV, and ZnO on PI measures 3.35 eV of optical band gap (Eg) from the Tauc plot. The photoelectrochemical cell (PEC) parameter measurement study shows that ZnO thin films on PET and PI plastic substrates have efficiencies (η = 0.93) and (η = 0.88), respectively. [ABSTRACT FROM AUTHOR]

The development of photocurable compositions is in high demand for the manufacture of functional materials for electronics, optics, medicine, energy, etc. The properties of the final photo-cured material are primarily determined by the initial mixture, which needs to be tuned for each application. In this study we propose to use simple systems based on di(meth)acrylate, polyimide and photoinitiator for the preparation of new photo-curable compositions. It was established that a fluorinated cardo copolyimide (FCPI) based on 2,2-bis-(3,4-dicarboxydiphenyl)hexafluoropropane dianhydride, 9,9-bis-(4-aminophenyl)fluorene and 2,2-bis-(4-aminophenyl)hexafluoropropane (1.00:0.75:0.25 mol) has excellent solubility in di(met)acrylates. This made it possible to prepare solutions of FCPI in such monomers, to study the effect of FCPI on the kinetics of their photopolymerization in situ and the properties of the resulting polymers. According to the obtained data, the solutions of FCPI (23 wt.%) in 1,4-butanediol diacrylate (BDDA) and FCPI (15 wt.%) in tetraethylene glycol diacrylate were tested for the formation of the primary protective coatings of the silica optical fibers. It was found that the new coating of poly(BDDA–FCPI23%) can withstand prolonged annealing at 200 °C (72 h), which is comparable or superior to the known most thermally stable photo-curable coatings. The proposed approach can be applied to obtain other functional materials. [ABSTRACT FROM AUTHOR]

The thermal hazard assessment of polyimide (PI) synthesis, including polyamide acid (PAA) and PAA imidization, was investigated owing to its uncontrolled viscosity and heat release. The thermal behavior of PAA with different viscosities investigated using a laboratory-scale setup and auto-reaction calorimetry (SIMULAR). The reaction enthalpy of PAA ranged from − 154.54 to − 156.82 kJ mol−1 as the viscosity increased from 7000 to 104,200 Pa s, indicating that heat release and viscosity increment were two opposite processes during PAA synthesis. The thermal behavior of PAA imidization was investigated using differential scanning calorimeter (DSC). The imidization of PAA was found to be an endothermic reaction with a heat absorption of 105.77 J g−1. Hence, the two-step PI synthesis is an exothermic reaction that concentrates on the synthesis of PAA. Second, the decomposition characteristics of PI in the isothermal mode were analyzed using DSC. The decomposition of PI occurred in the temperature range of 842.89–981.28 K, with a heat release of − 380.07 J g−1. The apparent activation energy of PI, calculated using the Ozawa model, ranged from 179.74 to 308.26 kJ mol−1. Finally, the thermal hazard level of PI was found to be Level 1 based on the Stoessel criticality diagram. This suggests that controlling the dosage can avoid implosion during PI synthesis because an increase in viscosity leads to a higher hazard. [ABSTRACT FROM AUTHOR]

Graphene with an atomically thin structure is considered to be a highly sensitive transducer capable of converting diverse external stimuli into measurable electrical signals. The generated signals, such as current and resistance, can be extracted through electrical contact to graphene. Conventional methods for contact formation are usually based on physical deposition of conductive materials on the target graphene. Here, we propose a method for in situ chemical synthesis of electrical contacts to graphene as an alternative approach that complements conventional physical methods. CO2 laser irradiation on a polyimide film with monolayer graphene on top can convert the polyimide surface to conductive electrodes of laser-induced graphene (LIG) that electrically connect to the existing graphene channel. Laser-scribing conditions, such as the power and scan rate, can modulate the contact resistance of the LIG–graphene junction. Various arbitrary shapes of in situ LIG contacts can be scribed to the direct writing ability of the laser. The proposed in situ LIG contact method can be extended to other carbon nanomaterials, such as carbon nanotubes and PEDOT:PSS. As a proof of concept of the in situ LIG contacts to graphene for electronic device applications, graphene field-effect transistors were demonstrated on a graphene-supported polyimide substrate with LIG–graphene junctions as source/drain electrodes. Our approach will pave the way for the simple and low-cost fabrication of versatile graphene electronic devices by utilizing the existing LIG technology specialized for energy devices and sensors. [ABSTRACT FROM AUTHOR]

Polyimide (PI) is a special engineering plastic, widely involved in mechanical components, instruments, and petrochemicals. However, single PI material is inevitably subject to wear and tear in practice, which leads to weakened material properties. In this work, Ti3C2Tx@SiO2 was prepared to enhance the wear resistance and lubrication properties of PI by intercalating SiO2 into the interlayer of Ti3C2Tx sheets. Ti3C2Tx@SiO2/PI composites were fabricated in two steps to test the tribological performances. SiO2 particles change the form of interfacial friction from sliding to rolling, thus relieving direct friction between material and steel ball. So, the composites have a minimum COF (COF = 0.33) when the content of Ti3C2Tx@SiO2 is 0.80 wt%. Moreover, the average value of wear rate was 0.24 × 10−5 mm3/(N·m) when Ti3C2Tx@SiO2 content was 1.60 wt%, which was 91.0% lower compared to the PI matrix. During the friction process, the abrasive chips of the material migrate to the surface of the steel ball to form a transfer film, which protects the material and thus reduces the wear rate. Therefore, the hybrids Ti3C2Tx@SiO2 are effective and important wear‐resistant agents and solid lubricants to improve the wear resistance and lubricity of PI or other polymer materials. Highlights: SiO2 insert Ti3C2Tx is a key factor in changing sliding friction into rolling friction, effectively reducing the COF.The average wear rate was 91.0% lower than that of the polyimide matrix when Ti3C2Tx@SiO2 content was 1.60 wt%.The minimum COF of Ti3C2Tx@SiO2/PI composites reached 0.33 when the content of Ti3C2Tx@SiO2 was 0.80 wt%.The transfer film effectively reduces further wear of the material during friction. [ABSTRACT FROM AUTHOR]

The incorporation of a "graphene-carbon nanotube-graphene" structure as a filler in polyimide composites to enhance their mechanical and thermal properties was investigated. The performance of the composites was evaluated by molecular dynamics simulations. Findings revealed that this arrangement significantly enhanced the mechanical strength and stiffness of the composites, improving their tensile and shear properties. [ABSTRACT FROM AUTHOR]

Copyright of Polymer Materials Science & Engineering is the property of Sichuan University, Polymer Research Institute and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Polyimide (PI) aerogels, renowned for their nano-porous structure and exceptional performance across a spectrum of applications, often encounter significant challenges during fabrication, primarily due to severe shrinkage. In this study, we innovatively incorporated ceramic fibers of varying diameters into the PI aerogel matrix to enhance the shape stability against shrinkage. The structure of the resulting ceramic fiber-reinforced PI (CF-PI) aerogel composites as well as their performance in thermal decomposition, thermal insulation, and compression resistance were characterized. The results revealed that the CF-PI aerogel composites dried by supercritical ethanol achieved greatly reduced shrinkage as low as 5.0 vol.% and low thermal conductivity ranging from 31.2 mW·m−1·K−1 to 35.3 mW·m−1·K−1, showcasing their excellent performance in shape stability and thermal insulation. These composites also inherited the superior residue-forming ability of ceramic fibers and the robust mechanical attributes of PI, thereby exhibiting enhanced thermal stability and compression resistance. Besides, the effects of different drying conditions on the structure and properties of CF-PI aerogels were also discussed. The coupling use of supercritical ethanol drying with the addition of ceramic fibers is preferred. This preferred condition gives birth to low-shrinkage CF-PI aerogel composites, which also stand out for their integrated advantages include high thermal stability, low thermal conductivity, and high mechanical strength. These advantages attribute to CF-PI aerogel composites substantial potential for a wide range of applications, particularly as high-performance thermal insulation materials for extreme conditions. [ABSTRACT FROM AUTHOR]

Copyright of Bearing is the property of Bearing Editorial Office and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Journal of Functional Materials / Gongneng Cailiao is the property of Chongqing Functional Materials Periodical Press and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)