Search

Copyright of Telecommunication Engineering is the property of Telecommunication Engineering and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

A miniaturized, high‐selectivity, wideband A‐T‐A frequency selective rasorber (FSR) based on compact spiral resonators (CSR) is proposed here. The lossy layer of the FSR consists of the CSR and a Jerusalem cross, with four resistors soldered onto the surface. The underlying layer is a bandpass frequency selective surface (FSS) with an extremely narrow slit. The dimensions of the FSR unit are only 0.079 λL × 0.079 λL × 0.078 λL. The extremely narrow‐slitted FSS and CSR together provide a narrowband frequency response, enhancing the selectivity of the FSR. Additionally, a prototype of an FSR was fabricated and tested, achieving results highly consistent with simulations. [ABSTRACT FROM AUTHOR]

In this paper, we propose for the first time a novel feed approach to a tightly coupled dipole array (TCDA). Firstly, compact zigzagging microstrip feedlines are utilized as baluns to feed our array elements to obtain wideband impedance-matching characteristics. Secondly, this array is designed on ultrathin substrates aiming at obtaining ultra-tight coupling between the dipole arms of two neighboring elements. Some irreplaceable parasitic pads are developed and added to the radiating arms to improve both the impedance and radiation characteristics of the TCDA. With these technologies, a 12 × 12 TCDA prototype is designed, fabricated and measured for verification. The array achieves an impressive impedance bandwidth spanning of 4–18 GHz for S 11 < − 10   dB . Its radiation patterns and realized gain are measured to verify its stable electromagnetic characteristics. Its realized gain is from 15 dB to 25 dB within the operating frequency band. Its efficiency is around 91%. Its measured results show good agreement with simulations. [ABSTRACT FROM AUTHOR]

A planar ultra-wideband modular antenna array with an ultra-low profile based on a tight coupling effect is proposed. The antenna array is composed of multi-layer printed circuit boards. Since its frequency operation can extend up to the grading lobe frequency, the number of T/R components for the antenna aperture is reduced to the greatest extent. Specifically, a horizontal "fin" structure is added on the parallel feeding lines, which assists in improving the impedance matching of the array. In order to break the bandwidth limitation of the low-frequency loop mode, a capacitive short-circuit probe is introduced to push the common-mode resonance point into the low-frequency band. Finally, subject to Active VSWR < 3, the array can realize E-plane, H-plane, and D-plane ± 45° beam scan coverage across the 6:1 frequency band (3.48–20.97 GHz). A 128-element prototype was processed and tested to validate the design. This array not only has the advantages of low profile, modularity, easy assembly, and maintenance but also minimizes the number of T/R components and reduces the cost of phased array antennas. [ABSTRACT FROM AUTHOR]

An ultra‐wideband and wide‐scan tightly coupled dipoles array based on frequency selective surface (FSS) is proposed, and the traditional wide‐angle scan impedance matching dielectric layer is replaced by FSS with printed metal strips to achieve the tuning of the scanning impedance of the array. Additionally, the metal strip FSS, dipole radiating elements and feeding structure are all printed on the same printed circuit board, and the whole design is highly integrated. Finally, a low‐cost lightweight single‐polarization tightly coupled antenna array with ultra‐wide band and wide scan performance is presented. Subject to the criterion of active Voltage standing Wave ratio(VSWR) < 3, beam scanning coverage of ±45° along E plane, H plane and D plane can be accomplished within the frequency band range across 0.4–2 GHz. An array prototype was produced and tested, and the results showed that the effectiveness of the design was well validated. [ABSTRACT FROM AUTHOR]

Organic semiconductors are attracting considerable attention as a new thermoelectric material because of their molecular diversity, non-toxicity and easy processing. The side chains which are introduced into two-dimensional (2D) transition metal dichalcogenides (TMDs) by covalent modification lead to a significant decrease in their thermal conductivity. Here, we describe a simple approach to preparing the side chains covalent modification TaS2 (SCCM-TaS2) organic/inorganic hybrid structures, which is a homogeneous and non-destructive technique that does not depend on defects and boundaries. Electrical conductivity of 3,401 S cm−1 and a power factor of 0.34 mW m−1 K−2 are obtained for a hybrid material of SCCM-TaS2, with an in-plane thermal conductivity of 4.0 W m−1 K−1, which is 7 times smaller than the thermal conductivity of the pristine TaS2 crystal. The power factor and low thermal conductivity contribute to a thermoelectric figure of merit (ZT) of ~0.04 at 443 K. The improvement of thermoelectric performance of materials by reducing lattice thermal conductivity is challenging. Here, the authors find the side chains covalent modification of transition metal disulfides reducing the lattice thermal conductivity. [ABSTRACT FROM AUTHOR]

Two-dimensional (2D) carbon materials, such as graphene, have attracted particular attention owing to the exceptional carrier transport characteristics that arise from the unique π-electron system in their conjugated carbon network structure1–4. To complement zero-bandgap graphene, material scientists have devoted considerable effort to identifying 2D carbon materials5–8. However, it is a challenge to prepare large-sized single-crystal 2D carbon materials with moderate bandgaps5,9. Here we prepare a single-crystal 2D carbon material, namely monolayer quasi-hexagonal-phase fullerene (C60), with a large size via an interlayer bonding cleavage strategy. In this monolayer polymeric C60, cluster cages of C60 are covalently bonded with each other in a plane, forming a regular topology that is distinct from that in conventional 2D materials. Monolayer polymeric C60 exhibits high crystallinity and good thermodynamic stability, and the electronic band structure measurement reveals a transport bandgap of about 1.6 electronvolts. Furthermore, an asymmetric lattice structure endows monolayer polymeric C60 with notable in-plane anisotropic properties, including anisotropic phonon modes and conductivity. This 2D carbon material with a moderate bandgap and unique topological structure offers an interesting platform for potential application in 2D electronic devices.Using an interlayer bonding cleavage strategy, a two-dimensional monolayer fullerene network is prepared; its moderate bandgap makes it a potential candidate for use in two-dimensional electronic devices. [ABSTRACT FROM AUTHOR]