Search

Polyaniline (PAni)–coated ZnO–SiO2–based hybrid material was prepared successfully with the in-situ polymerisation method and the product was subsequently analysed using XPS, XRD, TEM, UV-vis, TGA, FTIR and BET. The optical band gap calculated from the Tauc plot was found to be 2.89 eV. Moreover, this work reports an extensive study of the effect of the SiO2 on the electrochemical performance of hybrid material based on ZnO and PAni employing cyclic voltammetry. Furthermore, to evaluate the adsorption of methylene blue (MB), the parameters for the effectiveness of the adsorption process, including pH value, concentration and temperature, were investigated. The results indicated that the maximum adsorption of MB on the produced hybrid material occurred at pH 6.8 with a capacity reaching 71.2 mg.g−1. The thermodynamic studies indicate that the adsorption of MB on this adsorbent is spontaneous and endothermic in nature. Furthermore, PAni@ZnO–SiO2 is attractive for treating the effluents containing dyes due to its recyclability and high removal capacity. [ABSTRACT FROM AUTHOR]

Owing to environmental friendliness, waterborne coatings have attracted considerable attention for the protection of mechanical equipment. Herein, polyaniline (PANI)‐aniline modified silicon dioxide (ANSiO2) composite was prepared to improve the corrosion resistance of waterborne epoxy coatings through the modification of SiO2 nanoparticles by aniline‐methyl‐triethoxysilane and the subsequent in situ polymerization of aniline (AN). When the molar ratio of AN to ANSiO2 was 6:1, the obtained PANI‐ANSiO2 composite appeared spherical‐planar shape and was able to obviously improve the anticorrosive performance of the epoxy coatings. The impedance value of the PANI‐ANSiO2 composite modified coatings maintained above 108 Ω cm2 after being immersed in 3.5 wt% NaCl solution for 30 days, and the surface of the coating had no corrosion spread after 30 days of salt spray erosion test. The excellent anticorrosive effect of the PANI‐ANSiO2 was mainly attributed to not only the filling of the defective parts of the coatings by hydrophobic ANSiO2 but also the formation of passivation layer on the coating surface by PANI to impede electrochemical corrosion reaction. The preparation method in this work is facile, low‐cost, and easy produced on a large scale, and the environment friendly high‐anticorrosion coating shows great application potential in the field of metal protection. [ABSTRACT FROM AUTHOR]

Due to a worldwide shortage of water resources, removing dye pollutants from water is widely regarded as a crucial concern. Consequently, photocatalysis is gaining recognition as a viable approach for the treatment of water. In this study, Polyaniline/Bi2S3/NiFe2O4 nanocomposite is prepared by the coprecipitation method for the photodegradation of indigo carmine (IC) dye. The prepared samples are then examined via FTIR, XRD, TEM, SEM, VSM, PL, and DRS techniques. In the second part of the research, a thorough examination is conducted on the influence of photocatalyst dosage (0.1–1 g/L), initial concentration and pH (2–9), of dye solution (10–50 mg/L) on the photocatalytic degradation of IC dye under visible light irradiation. Results indicate that reducing pH, increasing time, and dosage of photocatalyst indicate a positive impact on dye removal efficiency. So that in the optimal conditions of pH = 2 with 0.5 g/L of photocatalyst in 10 mg/L of pollution solution, the highest efficiency of photocatalytic removal of IC dye is obtained 96.01%. In addition, the nanocomposite maintains 78.19% activity after four consecutive cycles. Based on the photocurrent and EIS Spectroscopy analyses, the enhanced photocatalytic efficiency of the Polyaniline/Bi2S3/NiFe2O4 nanocomposite can be ascribed to the expeditious separation and migration of electron–hole pairs and a lower charge transfer resistance. Finally, using the simplified Langmuir–Hinshelwood equation (first-order model) in kinetic studies recommended that the employed model is appropriate for precisely explaining the experimental data accurately. [ABSTRACT FROM AUTHOR]

Flexible PANI-Polyethersulfone (PES) fibers were fabricated using the wet-spinning technique. PANI particles were uniformly distributed within the matrix and micropores formed by the phase separation of PES, which prevented PANI particles aggregation and facilitated the formation of continuous ion transport channels. The experimental results reveals that the electrochemical performance of the fiber electrode material is optimal when the concentration of PES in the spinning solution is 15wt%. The assembled supercapacitor exhibits a commendable specific area capacitance of 162.75 mF·cm−2 at a current density of 0.5 mA·cm−2 and achieves an energy density of 14.47 mWh·cm−2 at a power density of 321.69 mW·cm−2. The capacitor retains 98.1% of its capacitance after 1 000 bending cycles. Therefore, the prepared fibers have good electrochemical properties and flexibility, and this simple and efficient preparation method is promising for the scalable production of flexible electrodes. [ABSTRACT FROM AUTHOR]

In this contribution, we report the investigation on removing of the oxochromium (VI), a hazardous species, using HCl-doped polyaniline (PAni-HCl) as adsorbent versus particles size. PAni-HCl has been successfully elaborated by conventional oxidative chemical method in the temperature range (0–3 °C). The recovered powder was milled and sieved into size ranges of < 50, 50–63, 125–160 and > 200 µm. The batch adsorption experiments were performed at 25 °C, using 250 mg of PAni-HCl dispersed in 250 mL of Cr(VI) aqueous solution (250 mg L−1). The Cr(VI) uptake was significantly influenced by both the particle size and contact time. Smaller particle sizes allow a quick initial adsorption and high removal efficiency (~100%). The kinetics of the Cr(VI) adsorption follow the pseudo-second-order model. A good correlation was demonstrated between the removal chromium (VI) properties (Qe,exp, k2 and τ(%)) and the (normalized) mean diameter ratio. [ABSTRACT FROM AUTHOR]

The green energy storage of polyaniline, without major wastages excreted into the environment is effectively demonstrated by using the polyaniline as supercapacitor electrode and the by-product obtained during the synthesis of polyaniline as its electrolyte. This green approach to the energy storage properties of sulphuric acid doped polyaniline (H-PANI) exhibited a substantial improvement in its energy storage, compared to the conventional approach of using an ionically conducting liquid as electrolyte like 1 M H2SO4 (SA), separately. The amelioration of 40.44% was achieved when the by-product obtained as supernatant liquid (SL) was used as electrolyte compared to SA. The H-PANI provided a specific capacity (Q) of 146.4 C g−1, a specific energy (E) of 24.40 W h kg−1 and a specific power (P) of 1.200 kW kg−1 at 1 A g−1 in the presence of SA. The Q of 205.6 C g−1, E of 34.26 W h kg−1 (similar range of E of Pb-acid batteries), P of 1.200 kW kg−1 were achieved in the presence of SL at 1 A g−1 and a high rate capability of 29.18% retention of initial Q up to 25 A g−1 was also achieved. This approach is useful to harvest high energy characters from PANI. [ABSTRACT FROM AUTHOR]

Graphene oxide and polyaniline have some unique properties and are considered as new generation materials for various applications. One major application of these materials is the adsorption of pollutants. In this study, Graphene oxide was synthesized with different levels of oxidation by using the modified Hummers method. Polyaniline/graphene oxide composite was synthesized by in situ polymerization with GO loading at 10% and 50% and further the composite is casted inside a disposable syringe by using N-methyl-2-pyrrolidone (NMP) as a dispersing agent. An adsorption experiment was carried out for water containing pesticide chlorpyrifos. The produced materials were characterized by FTIR spectroscopy & and XRD. Morphology was studied by SEM images. The FTIR spectra shows the formation of functional groups like -OH, -COOH on graphene, which may increase the hydrophilicity and adsorption properties. FTIR spectra of the composite portrayed the formation of bonds between polyaniline and graphene oxide. XRD peaks were obtained corresponding to crystals of polyaniline and graphite sheets. The adsorption efficiency was determined by analysis of water samples before and after filtration by using GC-MS. The composite produced with 50% amount of GO showed optimum results for the removal of chlorpyrifos. However, the composite with 10% GO loading is showing very low efficiency for the removal of chlorpyrifos. The PANI/GO composite is a possible candidate for the treatment of river water polluted by agricultural pollutants. [ABSTRACT FROM AUTHOR]

A novel PANI/NiCO2O4/CeO2 nanocomposite was prepared using the binary Nano metal oxide NiCo2O4/CeO2 with aniline and ammonium persulfate (APS) via a one-step polymerization and drop throwing system. The nanocomposite was explored by X-ray diffraction (XRD) analysis confirmed the successful integration of nanoparticles into PANI. UV-visible spectroscopy revealed absorbance peaks characteristic of PANI combined with nano metal oxides. Raman spectroscopy further verified the nanocomposite's structure, with peaks at 415, 517, 575, and 640 cm− 1 attributed to CeO2 and NiCo2O4 nanoparticles within the PANI matrix. Field emission scanning electron microscopy (FE-SEM) and energy dispersive X-ray spectroscopy (EDX) analyses of the doped PANI showed nanostructures ranging from 18.40 to 23.28 nm. Photodetection properties such as responsivity (Rλ), detectivity (D*), and external quantum efficiency (QE) of porous silicon nanocomposites were assessed using the drop-casting method. The incorporation of Ag/PANI-NiCo2O4-CeO2/PSi/Si/Ag enhanced the ideality factor of porous silicon. At wavelengths of 350–900 nm, the values of Rλ, D*, and QE were measured at 0.37 A/W, 5.3 × 10^12 cmHz^1/2/W, and 110%, respectively. [ABSTRACT FROM AUTHOR]

Fabrication of a novel nanocomposite named calcium ferrite/polyaniline (CaFe2O4-PANI) was reported and its potential for adsorption of toxic cationic dye named Victoria blue (VB) was studied in this work. The CaFe2O4-PANI has showcased improved adsorptive potential for VB dye with approximately 95.35 (±1.48)% of removal efficiency at solution pH 8.0, CaFe2O4-PANI dose of 0.5 g/L, contact time of 20 min and initial VB dye concentration of 50 mg/L. The adsorption process follows pseudo-second-order kinetic model and Freundlich isotherm model with a maximum uptake capacity of 266.67 mg/g. The adsorbent was also tested against surface and ground water sample loaded with VB dye and in presence of several ions. It was found that surface water has caused less interference (∼2 (±0.85)% reduction in VB dye removal efficiency) followed by ground water (∼4 (±0.91)% reduction) and wastewater (∼8 (±1.24)% reduction) and also the removal efficiencies are affected the most by bicarbonate ions (∼12 (±1.39)%–14 (±1.62)% reduction in VB dye removal efficiency). The experimental process was optimized utilizing a five level, three factor based response surface methodology (RSM) approach and the experimental parameters were optimized to CaFe2O4-PANI dosage = 0.5 g/L, contact time = 65 min and initial VB dye conc. = 60 mg/L, using the developed quadratic model to achieve a maximum VB removal efficiency of 98.63 (±2.13)%. Regeneration study suggests that the fabricated adsorbent can be reused up to five cycles with ∼10 (±1.13)% decrease in the VB dye removal efficiency. [ABSTRACT FROM AUTHOR]

The redox activities of polyaniline (PANI) are hindered by the instability of pernigraniline salt (PS) state which degrades into oligo‐aniline. In this work, the use of protic additives is examined to mitigate capacity fading and increase utilization of PANI in nonaqueous electrolytes. The protic additive propylene glycol, with its hydrogen‐bonding capabilities, stabilizes the PS PANI and promotes reversible redox reactions, facilitating high capacity and an extended cycle lifetime for applications in metal ion supercapacitors. The use of this protic nonaqueous electrolyte in a PANI–zinc device results in an energy density of 255 Wh kg−1 at a power density of 1.8 kW kg−1 and a robust cycle lifetime of 3,850 charge/discharge cycles. The PANI at a high current density of 6.5 mA cm−2 reaches a capacity of 257 mAh g−1, equivalent to 87% of the its theoretical capacity, showcasing the effectiveness of the protic additive in improving both capacity and cycle life in electrochemical supercapacitors. [ABSTRACT FROM AUTHOR]

Developing cutting-edge catalysts for oxygen evolution reaction (OER) is crucial for enhancing the efficiency of water splitting. Spinel-type materials have gained recognition for their exceptional catalytic performance in OER activity. The excessive OER overpotential is the significant obstacle that hinders the use of spinel-type materials. In this work, polyaniline (PANI) was incorporated to significantly enhance the performance of spinel SnFe2O4 material by straightforward hydrothermal method. SnFe2O4@PANI catalyst demonstrated an impressive overpotential of 198 mV at 10 mA cm–2 and a 33 mV dec–1 Tafel slope with higher OER activity. The electrochemical surface area (ECSA) of SnFe2O4@PANI catalyst was determined to be 2348.53 cm2, with higher cyclic stability of 25 h after 5000th cycles with minimal impedance characteristics (Rct = 0.18 Ω). In addition, the findings showed that the inclusion of PANI led to expansion of the surface area to improve the conductivity, resulting in notable enhancement of the catalysts' OER activity. This modification has resulted in an improved OER catalyst, making it highly sought after for various applications in the water-splitting field. Highlights: SnFe2O4@PANI catalyst was synthesized through hydrothermal route for improved OER activity. The SnFe2O4@PANI catalyst displays a reduced overpotential of 198 mV and Tafel slope of 33 mVdec−1. SnFe2O4@PANI catalyst demonstrates remarkable cycling stability of 25 h. SnFe2O4@PANI catalyst exhibits significantly lower impedance of Rct = 0.18 Ω. [ABSTRACT FROM AUTHOR]

Electronic devices and communication systems are highly susceptible to interference from unwanted electromagnetic waves. High-performance electromagnetic interference (EMI) shielding offers a solution to this issue. In this work, we discuss the design of an EMI shielding material composite using natural rubber (NR) filled with polyaniline (PANI), multi-walled carbon nanotubes (MWCNT), and ferric oxide (Fe2O3). Different properties of the material composite are studied using scanning electron microscopy (SEM), X-ray diffraction (XRD), and Fourier transform infrared (FTIR) spectroscopy. We tested the EMI shielding efficiency of the developed material in the X band and the Ku band. The measurements revealed improved shielding effectiveness when compared to similar microwave shielding materials. In terms of flexibility and cost-effectiveness, this novel composite also proved to be a better alternative. [ABSTRACT FROM AUTHOR]

Activated carbon (Ac) prepared from Thapsia transtagana was combined with a different ratio of aniline to synthesize Ac/PAni composites. Various characterization techniques, such as XRD, FESEM-EDX, TEM, and ATR-FTIR, were conducted to confirm the structure, surface morphology, and chemical characteristics of the composites. The materials were tested for eriochrome black T (EBT) adsorption. Batch results exposed that the Ac/PAni6 with the highest ratio of aniline displays the highest EBT removal efficiency. The kinetics of EBT adsorption over the Ac/PAni6 composite followed the Elovich model, and the equilibrium data suited the Redlich–Peterson and Toth isotherm models. The adsorption was spontaneous, feasible, and endothermic. The statistical physics equations have also been investigated. Four models have been proposed as one layer and two layers with one and two energies. The adsorption of EBT on the Ac/PAni6 composite correlated to the one layer two energies model. The statistical physical parameters, including the number of adsorbed molecules per site ( n 1 , n 2 ), the receptor sites density ( N 1 M , N 2 M ), the adsorption capacity at saturation ( Q 1 , Q 2 ), and the energy of adsorption ( E 1 , E 2 ) have all been considered. The total capacity at saturation is enhanced with temperature, which approves the endothermic nature of the process. The interpretation of the calculated energies E 1 and E 2 (< 40 kJ/mol) suggested that the EBT interaction with the Ac/PAni6 surface was mainly a physisorption process. [ABSTRACT FROM AUTHOR]

This work reports the electrochemical fabrication of thin films comprising polyaniline nanofibers (PANI) in conjunction with graphene oxide (GO) and reduced graphene oxide (rGO) on ITO substrate, along with examining the electrochemical properties, with a focus on the influence of the substrate and electrolyte in the electrodeposition methods. The study explores the electrochemical characteristics of these thin films and establishes a flexible framework for their application in diverse sectors such as sensors, supercapacitors, and electronic devices. It analyzes the impact of the substrate and electrolyte in electrodeposition techniques. The effects were studied using techniques such as cyclic voltammetry and chronoamperometry. The fabrication process of PANI/GO and PANI/rGO thin films involved the integration of rGO within PANI via electropolymerization, conducted under sulfuric acid. GO was synthesized by modifying the well-known Hummers' method and characterized by X-ray diffraction (XRD), and Fourier transform infrared spectroscopy (FTIR). SEM showed the diameters of the formed PANI were between 40 and 150 nm, which helped to intertwine the rGO nanosheets with PANI nanofibers to form thin films. The electrochemical behavior of the PANI/rGO thin films was examined using cyclic voltammetry (CV) and chronoamperometry in different electrolytes, including sulfuric acid (H₂SO₄) and potassium nitrate (KNO₃). The CV profiles exhibited distinct oxidation and reduction peaks, with variations in the voltammogram morphology attributed to the nature of the electrolyte and the substrate employed during the electrodeposition process. These results highlight the critical role of both the substrate and electrolyte in governing the electrochemical performance of PANI/rGO thin films. The findings from this study demonstrate a versatile approach for the fabrication of PANI/graphene-based thin films with tunable electrochemical properties, and such a strategy has great application to fabricating other thin film composites for supercapacitors or other control source frameworks requiring enhanced charge storage and electrochemical responsiveness. [ABSTRACT FROM AUTHOR]

This study presents, for the first time, a new method for the synthesis of polymers containing different ratios of oxidized quinoid and reduced benzenoid units in polyaniline (PANi)‐like structure. Copolymers were synthesized by an oxidative copolymerization method of p‐phenylene diamine (p‐PDA) and o‐anisidine (o‐An) in an organic medium using different initial compositions of monomers. The compositions of the copolymer were determined based on 1H NMR spectral data. The thermal stability, electrical conductivity, morphology, and solubility were studied and a comparative analysis with polyaniline and corresponding homopolymers was been carried out. The thermal behavior of copolymers was studied using thermogravimetric analysis and differential scanning calorimetry. It was found that during heating one endothermic process of water evaporation and two exothermic processes occur, which depend on copolymer composition, and only 30% weight loss occurs up to 600 °C. It is shown that room‐temperature conductivity of copolymers doped with hydrochloric and sulfuric acids ranges from 10−5 to 10−3 S cm−1 and increases with increasing concentration of o‐anisidine structural units. The conductivity of iodine‐doped copolymers is of the same order as the conductivity of iodine‐doped PANi in emeraldine and leucoemeraldine forms. The morphology of doped copolymers depends on the co‐monomer ratio and the type of dopants. [ABSTRACT FROM AUTHOR]

This review article focuses on the potential of cobalt oxide composites with conducting polymers, particularly polypyrrole (PPy) and polyaniline (PANI), as advanced electrode materials for supercapacitors, batteries, and supercapatteries. Cobalt oxide, known for its high theoretical capacitance, is limited by poor conductivity and structural degradation during cycling. However, the integration of PPy and PANI has been proven to enhance the electrochemical performance through improved conductivity, increased pseudocapacitive effects, and enhanced structural integrity. This synergistic combination facilitates efficient charge transport and ion diffusion, resulting in improved cycling stability and energy storage capacity. Despite significant progress in synthesis techniques and composite design, challenges such as maintaining structural stability during prolonged cycling and scalability for mass production remain. This review highlights the synthesis methods, latest advancements, and electrochemical performance in cobalt oxide/PPy and cobalt oxide/PANI composites, emphasizing their potential to contribute to the development of next-generation energy storage devices. Further exploration into their application, especially in battery systems, is necessary to fully harness their capabilities and meet the increasing demands of energy storage technologies. [ABSTRACT FROM AUTHOR]

This study highlights the non‐covalent interactions between corner‐functionalized derivatives of borophene and polyaniline. The study investigates B36, its derivatives having functional groups at all the six corners of outermost rim boron atoms i. e., B36‐H, B36‐OH, B36‐COOH, B36‐NH2 as well as five singly doped composites with polyaniline coded as, B36‐Pol, B36‐H‐Pol, B36‐OH‐Pol, B36‐COOH‐Pol and B36‐NH2‐Pol. The study discovers the features of these molecules by applying different quantum methods, i. e., frontier molecular orbitals (FMOs), IR, Raman, UV, linear polarizability (α0), 1st order polarizability (β0), non‐covalent interactions (NCI) density of states (DOS), Iso‐surface analysis, dipole moment (μ), vertical ionization energy (EVI), Molecular electrostatic potential (MEP) analysis, electron density distribution map (EDDM) analysis and quantum reactivity parameters using DFT directing towards the efficient Non‐Linear Optical (NLO) study. Compared to pristine B36, the efficiency of electron transfer in the doped complexes was considerably enhanced by minimizing the bandgap (Eg) from 4.66 to 1.27 eV and elevation of absorption (λmax) from 589.80 to 1500.23 nm. The complex B36‐OH‐Pol illustrates a significant rise in 1st order polarizability (βo=61371.91 au) due to lower excitation energies as compared to pristine B36 surface (βo=1016.38 au). DFT methods computed that all the structures demonstrated better charge transport properties after doping with polyaniline. Therefore, they can be promising candidates for future NLO applications, particularly B36‐OH‐Pol. [ABSTRACT FROM AUTHOR]

In this paper, BaFe12O19/Ni0.5Mn0.5Fe2O4@PANI core‐shell nanocomposites were synthesized with different ferrite/PANI ratios. The Ferrite nanoparticles were prepared by the auto‐combustion sol–gel method. Chemical oxidative polymerization of aniline in acidic solution along with adding ferrite nanoparticles to the composition was used for the synthesis of nanocomposites. The product then was studied by X‐ray diffractometer)XRD(, field emission scanning electron microscope (FE‐SEM), transmission electron microscope (TEM), and Fourier transform infrared spectroscopy (FTIR) analyses. The magnetic properties of samples were investigated with vibrating sample magnetometer (VSM). Also, nanocomposite samples were examined in terms of the ability to absorb microwaves. Using Vector Network Analyzer (VNA). the reflection loss (RL) of nanocomposites was measured at frequencies between 2 and 18 GHz. The minimum reflection loss (RLmin) was obtained at −36.98 dB at the frequency of 13.8 GHz with an effective absorption bandwidth of 4.87 GHz for the sample with the equal ratio of ferrite/PANI. Synthesized nanocomposite as an effective compound has very high reflection loss in a wide frequency range. Highlights: Thermal stability is improved by adding ferrite nanoparticles to polyaniline.The polymer shell reduces the magnetic properties of ferrite nanoparticles.There is a strong exchange coupling between hard and soft ferrite.Ferrite/polymer ratio of 1:1 has the lowest amount of reflection loss.In the X and Ku band, magnetic loss is mainly caused by eddy currents. [ABSTRACT FROM AUTHOR]

The urgent need for sustainable energy storage solutions has spurred research on high‐performance and cost‐effective energy storage technologies. Supercapacitors (SCs) show great potential due to their capacity to provide significant capacitance, energy and power density. This study focused on the enhancement of electrically conductive reduced Graphene Oxide (rGO) reinforced with polyaniline (PANI) composites to fabricate the supercapacitors. Various characterization techniques, including SEM, EDAX, Raman spectroscopy, FTIR, PXRD, TGA, BET, and CV were employed for the examination of the materials. The findings demonstrate that the rGO/PANI composite displayed nanostructured layers characterized by flaky leaf‐like structures, a trigonal crystal system, and a notable specific capacitance of 410 Fg−1, along with capacitance retention rate of 85 after completion of 1000 cycles. This composite showcases outstanding electrochemical performance leads to the promising material to use in SCs manufacturing. Highlights: Electrode showed pseudocapacitive behavior, capacitance of 392 F/g.PXRD pattern confirmed presence of benzenoid and quinonoid groups.BET analysis showed surface area of 16.850 m2/g, porous nature indicated.Electrode displayed good reversibility, with a‐b value of 0.6. [ABSTRACT FROM AUTHOR]

Layered vanadium‐based oxides have emerged as highly promising candidates for aqueous zinc‐ion batteries (AZIBs) due to their open‐framework layer structure and high theoretical capacity among the diverse cathode materials investigated. However, the susceptibility to structural collapse during charge‐discharge cycling severely hampers their advancement. Herein, we propose an effective strategy to enhance the cycling stability of vanadium oxides. Initially, the structural integrity of the host material is significantly reinforced by incorporating bi‐cations Na+ and NH4+ as "pillars" between the V2O5 layers (NaNVO). Subsequently, surface coating with polyaniline (PA) is employed to further improve the conductivity of the active material. As anticipated, the assembled Zn//NaNVO@PA cell exhibits a remarkable discharge capacity of 492 mAh g−1 at 0.1 A g−1 and exceptional capacity retention up to 89.2 % after 1000 cycles at a current density of 5 A g−1. Moreover, a series of in‐situ and ex‐situ characterization techniques were utilized to investigate both Zn ions insertion/extraction storage mechanism and the contribution of polyaniline protonation process towards enhancing capacity. [ABSTRACT FROM AUTHOR]

Polyaniline (PANI) provides an attractive organic platform for CO2 electrochemical reduction due to the ability to adsorb CO2 molecules and in providing means to interact with metal nanostructures. In this work, a novel PANI supported copper catalyst has been developed by coupling the interfacial polymerization of PANI and Cu. The hybrid catalyst demonstrates excellent activity towards production of hydrocarbon products including CH4 and C2H4, compared with the use of bare Cu. A Faradaic efficiency of 71.8 % and a current density of 16.9 mA/cm2 were achieved at −0.86 V vs. RHE, in contrast to only 22.2 % and 1.0 mA/cm2 from the counterpart Cu catalysts. The remarkably enhanced catalytic performance of the hybrid PANI/Cu catalyst can be attributed to the synergistic interaction between the PANI underlayer and copper. The PANI favours the adsorption and binding of CO2 molecules via its nitrogen sites to form *CO intermediates, while the Cu/PANI interfaces confine the diffusion or desorption of the *CO intermediates favouring their further hydrogenation or carbon‐carbon coupling to form hydrocarbon products. This work provides insights into the formation of hydrocarbon products on PANI‐modified Cu catalysts, which may guide the development of conducting polymer‐metal catalysts for CO2 electroreduction. [ABSTRACT FROM AUTHOR]

Water pollution is currently a critical global issue. Various research groups have developed active adsorbent materials. This study aims to enhance the adsorption of water pollutants, particularly fluoride, by modifying the electronic structure of red soil through in-situ chemical oxidative polymerization techniques. The synthesized materials were characterized using techniques including powder XRD, FT-IR, UV spectroscopy, and Conductometer, followed by testing their adsorption performance. The XRD analysis revealed that while the crystal structures of embedded red soil remained amorphous, polyaniline (PANI) and PANI/red soil (RS) nanoparticles became polycrystalline. The maximum adsorption capacity (qmax) of fluoride ions by PANI/RS was determined to be 9.35 mg/g. Optimization experiments showed that PANI/RS exhibited maximum adsorption performance for fluoride ions under specific conditions: pH 4.0, a contact time of 50 min, temperature of 35 °C, and an initial concentration of 15 mg/L with 2 mg of adsorbent, achieving a removal efficiency of 99.9%. Both Langmuir and Freundlich isotherm models demonstrated a good fit with the experimental data, with R² values of 0.94 and 0.95, respectively. This suggests that PANI/RS is an effective adsorbent material for removing fluoride ions from wastewater. Overall, PANI/RS outperformed red soil alone, demonstrating potential for practical application in water treatment processes. [ABSTRACT FROM AUTHOR]

Zinc‐air batteries (ZABs) with metal‐free cathodes are considered environmentally friendly and cost‐effective. However, more active and durable catalysts are required for this purpose. Herein, polyaniline (PANI)‐derived carbon materials were obtained to boost the oxygen reduction reaction (ORR) and, consequently, the performance of a primary ZAB. The developed porous N‐doped carbon (NDC) materials were engineered by varying the polymerization time and calcination temperature (500–900 °C). SEM micrographs and BET surface areas showed that the polymerization of aniline under cold conditions (5 °C) at 6, 8, or 24 h did not have a significant effect on the morphology or surface area. The fibrous structure of PANI was engineered by temperature, resulting in a progressive increase in the surface area until a three‐dimensional porous structure was achieved at 900 °C with the highest area of 601.9 m2 g−1. The surface doping of nitrogen species shifted from PANI‐rich N species to enriched graphitic N from 12.69 % (500 °C) to 24.26 % at 900 °C. The NDC 900 °C presented a voltage of 1.4 V and power density of 56 mW cm−2 (only 7 mW cm−2 lower than that of Pt/C). The results demonstrate that this material is an excellent candidate for high‐performance primary ZABs. [ABSTRACT FROM AUTHOR]

In this paper, PANI/CNTs composite materials were prepared by emulsion polymerization with sodium dodecyl benzene sulfonate (SDBS) and Tween-80 (Tween-80) as soft templates, ammonium persulfate (APS) as oxidant, and carbon nanotubes (CNTs) mixed with appropriate amount. The composite materials were characterized by scanning electron microscopy (SEM), X-ray powder diffraction (XRD) and Fourier transform infrared spectroscopy (FT-IR). The results show that PANI/CNTs composites present core-shell structure with fiber shape, and PANI materials cover the surface of CNTs uniformly. The electrochemical test results show that the specific capacitance of PANI/CNTs electrode is 478.48 F/g at the current density of 1.0 A/g. After 1 000 cycles, the specific capacitance retention rate of PANI/CNTs is 70.01%, while that of PANI prepared by traditional method is only 49.10%. The specific capacitance of PANI/CNTs composites obtained by emulsion polymerization is higher than that of PANI single material obtained by traditional method, and the cycle life is significantly improved. This method provides an important strategy for the preparation of electrode materials of high-performance supercapacitors. [ABSTRACT FROM AUTHOR]

The effect of SnCl2 dopant concentration on the properties of Sn-doped polyaniline (PANI) as a hole transport layer (HTL) for perovskite solar cells (PSC) was investigated. PANI films were synthesized by potentiostatic electropolymerization at 1 V vs. Ag/AgCl in sulfuric acid containing 0.1 M of aniline. The study analyzed various processes, including anodic charge transfer, diffusion, crosslinking, and coordination of SnCl2. Results showed that SnCl2 doping decreased the branching of PANI chains and enhanced the thermal properties of PANI. The Raman spectrum confirmed crosslinking behavior due to the incorporation of Sn. Thermogravimetric analysis, derivative thermogravimetry, and differential scanning calorimetry supported SnCl2 coordination to the PANI backbone. Optical measurements revealed a decrease in transmittance and reflectance and a substantial decrease in the band gap as the concentration of SnCl2 increased. Mechanism of PANI growth and different early stage reactions are thoroughly discussed. [ABSTRACT FROM AUTHOR]

Polyaniline (PANI), Tungsten oxide (WO3), and PANI:WO3 nanocomposites are prepared by a simple chemical synthesis method and samples are characterized by various characterization. techniques. SEM analysis showed that the WO3 nanoparticles have a strong effect on the morphology of the nanocomposites. The PANI composite exhibited distinctive spherical, granular, and organism-like structures, indicating successful synergistic interactions between PANI and WO3. Elemental analysis confirmed the formation of pure WO3 nanoparticles. The XRD pattern exhibits distinct peaks at 27.6° and 32.5°, which correspond to the (2 0 1) and (0 2 2) planes of WO3, respectively. These peaks indicate an anorthic crystal structure. The observed peak positions are in good agreement with the standard values provided in JCPDS Card nos. 83–0947 and 72–0677, confirming the accurate determination of the crystal structures. Optical emission and UV–Vis spectroscopy revealed changes in electronic transitions and band structures, indicating semiconducting behavior of the PANI nanocomposites. Notably, the direct band gap energy of the PANI composite was found to be 3.84 eV, compared to the band gap energies of pure PANI and WO3 at 4.26 eV. This observed decrease in band gap energy further suggests enhanced semiconducting properties of the composite. FT-IR spectroscopy highlighted common bonding characteristics, affirming the effective integration of PANI and WO3. Electrical studies unveiled enhanced charge carrier mobility, promising advanced electronic applications. The synthesized samples are evaluated for their antibacterial properties against Bacillus subtilis, a Gram-positive bacterium. The results demonstrate significant bactericidal activity, as evidenced by the clear zones of inhibition measuring approximately 11–13 mm in diameter. [ABSTRACT FROM AUTHOR]

The present study reports very low concentration ammonia detection at room temperature. The sensing material is a composite of polyaniline (PANI) and graphene oxide (GO). The composite material is prepared by ex situ chemical synthesis technique by coating PANI on GO sheets. Prior to the sensing study, the composite material is characterized by XRD, FESEM, Raman, FTIR and TGA. The results of XRD, FESEM, Raman and FTIR suggest the formation of the composite and some interaction between PANI and GO. TGA reveals better thermal stability of the composite over the bare materials. The sensing of the material towards ammonia ( NH 3 ) is observed to be excellent at concentration level as low as 5 ppm. The response and recovery times are 21 s and 37 s, respectively. Also, the sensor shows long-term stability. [ABSTRACT FROM AUTHOR]

In this research work, a polyaniline-multiwalled carbon nanotube (MWCNT)-based gas sensor is fabricated and tested for CO2 gas at room temperature. Polyaniline-MWCNT (PCT) composites were synthesized through a chemical oxidation process using FeCl3 as an oxidant. The polymerization process was conducted at room temperature. The PCT composites were characterized using XRD, FTIR, UV spectroscopy, scanning electron microscopy (SEM), and impedance spectroscopy. The PCT 15% shows highest sensitivity at room temperature. XRD and FTIR spectroscopy confirm the formation of a PCT composite. SEM image confirmed the change in morphological structure for PCT 15% composite than pure polyaniline. Through impedance spectroscopy, it was found that all the composites show conductive properties as their phase angle is less than 90°. The response and recovery time of PCT (5%, 10%, 15%, and 20%) was found to be (148 s, 121 s), (125 s, 141 s), (110 s, 261 s), and (121 s, 63 s). [ABSTRACT FROM AUTHOR]

Copyright of Advanced Textile Technology is the property of Zhejiang Sci-Tech University Magazines and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

This study presents the use of novel Ganga-sand-encapsulated polyaniline granules for effective remediation of textile and pharmaceutical wastewater. The prepared Ganga-sand-encapsulated polyaniline granules were characterised using scanning electron microscope (morphology) and Fourier transform infrared techniques. The effect of adsorbent dose, contact time, pH and concentration influence on the adsorption performance of Ganga-sand-encapsulated polyaniline granules for the removal of methylene blue dye (textile waste) and doxycycline antibiotic (pharmaceutical waste) was studied. Kinetic and isotherm studies were also carried out to investigate the adsorption process further. The maximum adsorptive removal efficacy of methylene blue and doxycycline was found as 98.2% and 85.1%, respectively, at the optimised condition of adsorbent dose: 8 g/L, time: 120 min, pH: 12 and concentration: 50 ppm. From adsorption kinetics, it was established that the adsorption process followed pseudo-second-order (PSO) rather than pseudo-first-order (PFO). The correlation coefficient values for PFO and PSO models were 0.9012 and 0.9992, respectively, for methylene blue dye adsorption on Ganga-sand-encapsulated polyaniline granules. The adsorption isotherm study established that the adsorption process followed the Langmuir model rather than the Freundlich model. This study found that Ganga-sand-encapsulated polyaniline granules can be a promising adsorbent for textile and pharmaceutical wastewater treatment. [ABSTRACT FROM AUTHOR]

The intensive investigation of supercapacitors and other advanced energy storage technologies has been driven by the growing demand for portable electronic devices, electrical equipment, and hybrid electric vehicles in the transportation sector. To develop these systems, it is crucial to have electrodes capable of high energy storage, along with suitable electrolytes to facilitate ion transport or conduction. These energy storage devices, which incorporate nanostructured and compact electrodes, exhibit excellent electrochemical performance. The hybrid nanostructured composites made of carbon allotropes and conducting polymers have received much attention recently due to their possible use in supercapacitors. They are perfect candidates for energy storage applications because of their high electrical conductivity, mechanical strength, and stability. We synthesized reduced graphene oxide by a modified Hummer's method and composited it with aniline monomers by in situ chemical polymerization to fabricate nanostructured composites of polyaniline and graphene. The different samples were synthesized by varying their mass ratios followed by their characterization by different characterization techniques such as XRD, FTIR, Raman, FESEM, and cyclic voltammetry, etc. [ABSTRACT FROM AUTHOR]

A growing interest in dental practice in intranasal anesthesia using tetracaine and oxymetazoline dictates the need for their simultaneous determination in combination drugs and human saliva. Potentiometric multisensory systems based on perfluorosulfonic acid membranes, including polyaniline‐modified ones, were developed for these purposes. A change in the distribution of the sensor sensitivity to the related analytes was achieved by variation of the conditions for concentration polarization at the membrane interface with a studied solution due to a change in the intrapore volume, nature, and availability of the sorption centers, as well as the hydrophilicity of the membrane surface that were specified by the conditions for their synthesis and subsequent hydrothermal treatment. Reversibility of the analyte sorption using the chosen conditions for regeneration provided long‐term stable work of both the sensors and the calibration equations established by multivariate linear regression. The membrane modification promoted their resistance to fouling. The relative errors of the simultaneous tetracaine and oxymetazoline determination in the combination drug solutions were no greater than 7% and 11%, while in the artificial saliva solutions, they were 15% and 17%, respectively, when an array of the cross‐sensitive sensors based on the composite membranes prepared by different methods was used. The analysis errors were reduced to 3%–6% when analyzing the drug and to 0.2%–6% when analyzing the artificial saliva if an array was organized with the sensors based on the membrane with the dopant and the membrane without it, due to the decreasing correlation between their responses. Potentiometric multisensory systems based on perfluorosulfonic acid membranes, including polyaniline‐modified ones, were developed for the simultaneous determination of tetracaine and oxymetazoline in combination drugs and human saliva. Reversibility of the analyte sorption during regeneration provided long‐term stable work of the sensors and calibration equations established by multivariate linear regression. The analysis errors were 0.2%–6% for the sensor array based on the membrane with polyaniline and the one without it, due to the low correlation between the responses. [ABSTRACT FROM AUTHOR]

Although polyaniline has a high electroactivity in environments below pH 5, it loses its electroactivity in neutral and basic environments. In addition, polyaniline film does not give physically stable film when it becomes thick. For these reasons, polyaniline has been synthesized in the presence of other monomers or inorganic/organic species, leading to the obtaining of composite polymers with some new electrochemical and physical properties. In this study, novel composite polymer films of polyaniline were synthesized electrochemically in the presence of different concentrations of Na2MoO4.2H2O and Na2WO4.2H2O, and these composite polymer films were examined in monomer-free solutions for electrochemical investigation. As a result, the cathodic charge of polyaniline increased from 0.25 mC to 1.50 mC in the presence of 0.05 M Na2MoO4.2H2O. Also, the polyaniline/WO3 composite achieved a charge transfer of 0.42 mC in the presence of 0.25 M NiSO4.2H2O, 0.05 M NiCl2.6H2O, Na2WO4, Na2MoO4.2H2O, 0.4 M Na3C6H5O7.2H2O and 0.05 Na2WO4.2H2O as a metal source. These prove the better charge transfer during the redox reaction of the polyaniline composite film. [ABSTRACT FROM AUTHOR]

The increasing demand for high-performance materials has led to the development of natural fiber composites as an alternative to synthetic fiber composites. However, the low thermal conductivity of natural fibers limits their use in advanced applications. In this study, we have developed polyaniline-coated natural fiber composites to enhance their thermal properties. The methodology of this study involves the preparation of natural fiber composites using polyaniline-coated natural fibers as a reinforcement and a bio-based resin as a matrix. The composites were then coated with polyaniline, which was synthesized through chemical oxidation of aniline monomer. The coated composites were characterized using various analytical techniques such as Fourier-transform infrared spectroscopy, scanning electron microscopy, and thermogravimetric analysis to evaluate their structural, morphological, and thermal properties. The materials used in this study were natural fibers, bio-based resin, aniline monomer, ammonium persulfate, and hydrochloric acid. The gap identification of this study is the low thermal conductivity of natural fiber composites, which limits their application in advanced fields such as aerospace, automotive, and electronics. The problem identification is the lack of a cost-effective and eco-friendly method to enhance the thermal properties of natural fiber composites. The results of this study showed that the polyaniline-coated natural fiber composites exhibited enhanced thermal conductivity compared to the uncoated composites. The improvement in the properties of the composites was attributed to the high conductivity of polyaniline and its ability to form a continuous conductive network throughout the composite matrix. The development of polyaniline-coated natural fiber composites provides a cost-effective and eco-friendly approach to enhance the thermal properties of natural fiber composites. This approach has the potential to expand the use of natural fiber composites in advanced applications, leading to a sustainable and greener future. [ABSTRACT FROM AUTHOR]

Growing volumes of textile waste and heavy metal pollution of water are emerging environmental challenges. In an attempt to tackle these issues, a non-woven sorbent based on jute fibers was fabricated by recycling the textile waste from the carpet industry. The influence of contact time, concentration, pH and temperature on the sorption of lead and copper ions from aqueous solutions was studied. In order to enhance the sorption capacity of the non-woven material, in situ synthesis of polyaniline (PANI) in the presence of TiO2 nanostructures was performed. The contribution of TiO2 nanoparticles and TiO2 nanotubes to the uniformity of PANI coating and overall sorption behavior was compared. Electrokinetic measurements indicated increased swelling of modified fibers. FTIR and Raman spectroscopy revealed the formation of the emeraldine base form of PANI. FESEM confirmed the creation of the uniform nanocomposite coating over jute fibers. The modification with PANI/TiO2 nanocomposite resulted in a more than 3-fold greater sorption capacity of the material for lead ions, and a 2-fold greater absorption capacity for copper ions independently of applied TiO2 nanostructure. The participation of both TiO2 nanostructures in PANI synthesis resulted in excellent cover of jute fibers, but the form of TiO2 had a negligible effect on metal ion uptake. [ABSTRACT FROM AUTHOR]

This study evaluates the preparation of novel ternary functional adsorbents based on polyaniline, zinc oxide nanoparticles, and moringa oleifera gum to produce zinc oxide/Moringa oleifera gum-grafted L-methionine-functionalized polyaniline bionanocomposites (ZM-g-Pani) and employed to sequestrate divalent metal ions (Cd2+, Hg2+ and Pb2+) from wastewater samples. The morphological and structural properties of ZM-g-Pani were exploited using FT-IR, FE-SEM/EDS, TEM, and XRD. FT-IR and FE-SEM studies show that the as prepared nanocomposite has an abundant number of reactive groups and a porous structure, thus demonstrating outstanding divalent metal cation removal. FT-IR study confirms that the attachment of L-methionine to polyaniline is facilitated by the C-S linkage. Both TEM and FE-SEM techniques confirmed the clustered granules of ZnO over the surface of polyaniline, which ultimately provided more surface area to adsorb metal ions. The study demonstrated that Cd2+, Hg2+ and Pb2+ ions could undergo physical sorption and chemisorption simultaneously during the adsorption process. The maximum adsorption capacity was 840.33, 497.51, and 497.51 mg/g for Cd2+, Hg2+, and Pb2+, respectively. The impact of co-existing ions, including NO3−, PO43−, SO42−, Cl−, Na+, Cu2+, and Al3+, showed that there were no notable alterations in the adsorption of the selected metal ions with ZM-g-Pani. ZM-g-Pani showed eight successive regeneration cycles for Cd2+, Hg2+, and Pb2+ with more than 85% removal efficiency. [ABSTRACT FROM AUTHOR]

In recent years, wearable smart textiles with multifunctional properties have attracted great interest for use with a wide range of applications, including personal protection, sport, healthcare etc. In the present study, all-in-one multifunctional conductive hydrophobic coated cotton fabric with electromagnetic interference (EMI) shielding, joule heating, and antibacterial properties was prepared via in-situ chemical oxidative polymerization. A graphene oxide (GO)–polyaniline (PANI)–silver (Ag) composite was coated onto the cotton fabric, exhibiting a low electrical resistance of 24.3 Ω sq−1 and strong hydrophobicity, with a water contact angle of ~ 139°. The high electrical conductivity of the composite coating resulted in excellent EMI shielding of ~ 52 dB in the X-band frequency region. Notably, the EMI shielding performance was tunable by simply changing the pH due to the acid- and alkali-sensitive nature of PANI. Furthermore, the fabricated conductive cotton fabric demonstrated excellent joule heating, achieving a temperature of 105.7 °C within 30 s at a voltage of 3.5 V. Additionally, in the presence of Ag, the cotton fabric exhibited excellent anti-bacterial properties against both Gram-positive (Staphylococcus aureus) and Gram-negative (Escherichia coli) bacteria. [ABSTRACT FROM AUTHOR]

This paper introduces a novel wearable flexible gas sensor designed specifically for the detection of d‐limonene. The sensor utilizes materials recognized for their high efficiency‐to‐cost ratio, notably polyaniline (PANI) combined with carboxylated multiwalled carbon nanotubes (MWCNT) and graphene oxide (GO) as sensing layers. The study conducts a comprehensive analysis of the nanocomposite layers, examining their functional groups, morphology, topography, thickness, crystallinity, thermal behavior, surface area, as well as the size and volume of their pores. This examination showed distinctions among the nanocomposite layers. PANI/GO exhibited larger pore size and thickness, while PANI/MWCNT_COOH demonstrated a higher surface area. The analysis of thermal stability demonstrated that the film employing the DBSA dopant exhibited the lowest stability. Morphological characterizations showed a globular structure for PANI, tubular characteristics for PANI/MWCNT_COOH, and a flat nature for PANI/GO. When detecting d‐limonene, nanocomposite films doped with HCl demonstrated notably superior response levels. The gas sensors exhibited high sensitivity (>2.24 mV/ppm), a narrow range for the limit of detection (0.12–0.52 ppm), and excellent reversibility, stability, and selectivity. These findings suggest the possibility of broadening the application of gas sensors to monitor additional volatile compounds, with a particular emphasis on the online monitoring of agricultural products. [ABSTRACT FROM AUTHOR]

Present work reports solution combustion synthesis (SCS) of Co0.5Zn0.5Fe2O4 spinel ferrite, its chemical modification with polymethylmethacrylate (PMMA), synthesis of polyaniline (PANI), and electromagnetic interference (EMI) shielding properties of their composites. Both as-prepared and PMMA-modified Co0.5Zn0.5Fe2O4 adopt cubic spinel structure as shown by X-ray diffraction studies. Field emission scanning electron microscopy images show the agglomerated and microporous nature of the ferrites. High resolution transmission electron microscopy image of as-prepared Co0.5Zn0.5Fe2O4 shows lattice fringes related to (311) plane of the spinel structure. X-ray photoelectron spectroscopy studies reveal the presence of Co2+, Zn2+, and Fe3+ in tetrahedral and octahedral coordinations in the ferrite. EMI shielding properties are evaluated for PMMA-modified Co0.5Zn0.5Fe2O4 and PANI composites in different weight ratios. Composites containing PMMA-modified ferrite and PANI with 50:50 and 10:90 weight ratios show the best performance among all the composites in 2−20 GHz frequency range. Optimized PMMA-modified Co0.5Zn0.5Fe2O4 and PANI composite with the ratio of 10:90 shows shielding effectiveness (SE) values of −16.6 to −24.2 dB in 2−20 GHz frequency region. [ABSTRACT FROM AUTHOR]

Three types of synthetic coal-derived adsorbents were characterized as potential enhanced structurers during the removal of chlorpyrifos pesticide. The raw coal (CA) was activated into porous graphitic carbon (AC), and both CA and AC were blended with polyaniline polymers (PANI/CA and PANI/AC) forming two advanced composites. The adsorption performances of the modified structures in comparison with CA were evaluated based on both the steric and energetic parameters of the applied advanced isotherm model (the monolayer model of one energy). The uptake performances reflected higher capacities for the PANI hybridized form (235.8 mg/g (PANI/CA) and 309.75 mg/g (PANI/AC) as compared to AC (156.9 mg/g) and raw coal (135.8 mg/g). This signifies the impact of activation step and PANI blending on the surface and textural properties of coal. The steric investigation determined the saturation of the coal surface with extra active sites after the activation step (Nm(AC) = 62.05 mg/g) and the PANI integration (Nm(PANI/CA) = 113.5 mg/g and Nm(PANI/AC) = 169.7 mg/g) as compared to raw coal (Nm(CA) = 39.6 mg/g). This illustrated the reported uptake efficiencies of the modified samples, which can be attributed to the enhancement in the surface area and the incorporation of additional chemical groups. The results also reflect that each site can be loaded with 3–4 molecules of chlorpyrifos, which are arranged vertically and adsorbed by multi-molecular mechanisms. The energetic studies (< 40 kJ/mol) suggested the physical uptake of pesticide molecules by dipole bonding and hydrogen bonding processes. The thermodynamic functions donate the exothermic properties of 47reactions that occur spontaneously. [ABSTRACT FROM AUTHOR]

In this work, a facile synthesis procedure was developed to deposit Pt−Pd dendrites using the chronopotentiometry (CP) method on polyaniline/carbon nanotube composites. The morphology of the bimetallic Pt−Pd dendrites exhibited a petal‐like shape. The results indicated that multi‐walled carbon nanotubes with larger diameters (approximately 60 nm) demonstrated enhanced support capabilities for achieving uniform dispersion of Pt−Pd dendrites. The electrochemical mass activity for methanol oxidation reaction (MOR) of Pt72Pd28/PANI/CNTs composites reached 670 mA mg−1Pt+Pd, representing a 1.2‐fold increase compared to that of Pt/C. Moreover, the If/Ib value of Pt72Pd28/PANI/CNTs catalyst was 1.9 times higher than that of Pt/C catalyst. Notably, the Pt72Pd28 dendrites displayed superior catalytic performance and COad tolerance in comparison to commercial Pt/C catalysts, as evidenced by their high mass activity and If/Ib value. These research findings present a novel approach for preparing highly active Pt−Pd binary catalysts. [ABSTRACT FROM AUTHOR]

Fe-Ca-SAPO-34/CS/PANI, a novel hybrid bio-composite scaffold with potential application in dental tissue engineering, was prepared by freeze drying technique. The scaffold was characterized using FT-IR and SEM methods. The effects of PANI on the physicochemical properties of the Fe-Ca-SAPO-34/CS scaffold were investigated, including changes in swelling ratio, mechanical behavior, density, porosity, biodegradation, and biomineralization. Compared to the Fe-Ca-SAPO-34/CS scaffold, adding PANI decreased the pore size, porosity, swelling ratio, and biodegradation, while increasing the mechanical strength and biomineralization. Cell viability, cytotoxicity, and adhesion of human dental pulp stem cells (hDPSCs) on the scaffolds were investigated by MTT assay and SEM. The Fe-Ca-SAPO-34/CS/PANI scaffold promoted hDPSC proliferation and osteogenic differentiation compared to the Fe-Ca-SAPO-34/CS scaffold. Alizarin red staining, alkaline phosphatase activity, and qRT-PCR results revealed that Fe-Ca-SAPO-34/CS/PANI triggered osteoblast/odontoblast differentiation in hDPSCs through the up-regulation of osteogenic marker genes BGLAP, RUNX2, and SPARC. The significance of this study lies in developing a novel scaffold that synergistically combines the beneficial properties of Fe-Ca-SAPO-34, chitosan, and PANI to create an optimized microenvironment for dental tissue regeneration. These findings highlight the potential of the Fe-Ca-SAPO-34/CS/PANI scaffold as a promising biomaterial for dental tissue engineering applications, paving the way for future research and clinical translation in regenerative dentistry. [ABSTRACT FROM AUTHOR]

The development of efficient supercapacitors hinges on the innovation of superior electrodes, which are pivotal in augmenting their energy storage capabilities. Supercapacitors, recognized for their high‐power density and extended cycle life, play a crucial role as sustainable solutions in addressing energy storage challenges. A fundamental aspect of supercapacitor functionality involves the electrode material, which works in concert with other key components such as the current collector, separator, and electrolyte. This study focuses on evaluating the impact of the current collector material on the performance of symmetric supercapacitors. We investigated the electropolymerization of polyaniline on woven steel mesh current collectors of varying mesh sizes, ranging from 20 to 200 mesh per inch, using assorted deposition conditions. The electrochemically modified woven steel meshes were utilized to construct symmetric supercapacitors. The electrochemical performance of the assembled supercapacitors, configured in a two‐electrode system, was investigated using a variety of electrochemical techniques to better understand the kinetics of electrolyte ion migration. Notably, the 20‐mesh size, characterized by the fewest pores per inch, demonstrated superior performance with an optimum capacitance of 4730 mF/cm2, an energy density of 317.8 μWh/cm2, and a power density of 400 μW/cm2 at a current density of 1 mA/cm2. [ABSTRACT FROM AUTHOR]

The construction and assessment of an effective, cost-efficient anode catalyst for methanol oxidation reactions (MOR) are crucial in direct methanol fuel cells (DFMC) applications. This work unveils a quick, simple, yet effective method for synthesizing poly(aniline-co-pyrrole) using the "chemical oxidative polymerization" technique and creates an affordable and stable anode catalyst for DMFC applications. The chemical oxidative polymerization approach was employed to copolymerize aniline and pyrrole with incorporation of nickel, and the electrocatalyst showcased remarkable activity towards methanol oxidation reaction (MOR). Physiochemical characterizations such as scanning electron microscopy, FT-infrared spectroscopy, Raman spectroscopy, and thermogravimetric analysis were performed to validate the incorporation of transition metal nickel into the copolymerized conducting polymers (aniline-co-pyrrole), abbreviated as PANiPPy. Electrochemical techniques like cyclic voltammetry, chronoamperometry, and electrochemical impedance spectroscopy (EIS) were used to investigate the capability of the electrocatalysts to oxidize methanol in alkaline conditions. The electrode material NiPANiPPy displayed a higher oxidation current density 280.60 mA/cm2 from the cyclic voltammogram of the electrocatalysts in 1 M KOH + 1 M methanol compared to the other synthesised electrocatalysts since nickel provides a low onset potential while the copolymers PANiPPy provide good conductivity and mechanical stability. Moreover, NiPANiPPy exhibits the lowest current rate loss and a substantially higher current density among them after 3600 s with the highest current density of 100 mAcm−2. NiPANiPPy was also observed to have the lowest solution resistance with 0.8 Ω compared to other electrocatalysts in EIS spectra. Thus, the synthesized electrocatalysts has potential applications as an enhanced anode electrode for DMFC. [ABSTRACT FROM AUTHOR]

This paper presents a novel binder-free electrochemical synthesis of a porous ternary composite comprising polyaniline/multiwall carbon nanotubes decorated with silver nanoparticles (Ag@PANI/MWCNTs), which serves dual functions as a photocatalyst for methylene blue degradation and as an electrode for high-performance supercapacitors application. Various characterization techniques confirm that the synthesized Ag@PANI/MWCNTs composite exhibits excellent optical, chemical, electrical, structural, morphological, electrochemical and photocatalytic characteristics. The composite exhibits excellent electrochemical and photocatalytic efficacy attributed to its porosity, higher surface area, conductivity and rapid redox properties. Electrochemical tests reveal specific capacitance of 862 F/g, energy density of 65.78 Whkg−1, power density of 444.44 Wkg−1 and cycling stability with 79% capacitance retention even after 10,000 cycles. As a photocatalyst, the composite achieves approximately 95% degradation in 25 min with reusability up to five cycles. It also exhibits high transient photocurrent responses (0.36 mA/cm2) and a high-rate constant (0.13 min−1), confirming excellent photocatalytic activity. The synergistic effect of PANI/MWCNTs and the incorporation of Ag nanoparticles contribute to the outstanding performance of the synthesized nanocomposite. Thus, it is expected that the synthesized Ag@PANI/MWCNT is a promising ternary composite which may prove to be a noble material for photocatalytic and energy storage-related devices. [ABSTRACT FROM AUTHOR]

Humidity sensors have gained tremendous attention due to their practical applications in the pharmaceutical industry, food processing, biomedical applications, microelectronics, and meteorology. Herein, a polymer-based multifunctional humidity sensor (PANI-Bi-ZnO) has been fabricated. This study describes a polymer-based capacitive-type humidity sensor that has excellent repeatability, negligible hysteresis (0.5% RH at 60% RH), quick response (8 s) and relaxation times (20 s), high stability (30 days), high sensitivity, and good linearity in a wide humidity detection range of 10–90% RH and has become increasingly significant for applications involving industrial control and environmental monitoring. Moreover, the fabricated sensor possesses a highly reliable/stable output performance that remains constant after multiple test cycles. The current work also provides a cost-effective method to fabricate high-performance humidity sensors. The designed humidity sensor would be an excellent choice for measuring a variety of applications in the field of humidity. [ABSTRACT FROM AUTHOR]

In this study, modified activated carbon fibers and phytic acid-doped polyaniline/activated carbon fiber composites were successfully prepared by modifying activated carbon fibers and compounding polyaniline. The electrokinetic adsorption combined remediation technology was used to study the remediation of cadmium-contaminated soil. The results showed that when the electric field intensity was 2 V cm−1 and the repair time was 120 h, 0.1 mol L−1 citric acid solution was circularly added to the cathode using electrolyte. The current during the repair process showed periodic fluctuations with the extension of the repair time. The current of adding P-PANI/ACF adsorbent near the cathode region was larger than that of other groups, and cadmium has a higher removal rate. The mean removal rate of Cd(II) in soil with a content of 60 mg kg−1 reach 76.94%. [ABSTRACT FROM AUTHOR]

In the present study, a quaternary composite consisting of α-ketoglutaric acid, chitosan, polyaniline, and graphene oxide (α-CTS-PANI-GO) was synthesized and characterized by Scanning Electron Microscope, Fourier Transform Infrared Spectroscopy, and Raman spectroscopy. The adsorption of dye on the film was proved by the X-ray diffraction analysis method. According to the increase in the intensity of the peak before and after adsorption, it showed the presence of Methylene Blue (MB) and Acid Orange 7 (AO7). Also, the appearance of peaks related to sulfur in Energy dispersive X-ray (EDX) and EDX elemental mapping, and X-ray photoelectron spectroscopy data after the adsorption process proved the presence of dyes compounds and their adsorption by the synthetic film. The simultaneous removal properties of α-CTS-PANI-GO were evaluated in the removal of cationic and anionic dyes, MB and AO7. Using the Central Composite Decomposition, the effect of different variables such as pH, temperature, adsorbent dose, and time on AO7 and MB removal was studied. The regeneration of α-CTS-PANI-GO film was studied and the zero point charge of the synthesized film was also determined. Various isotherm models, such as Langmuir and Freundlich, were investigated, and the processing of experimental equilibrium data confirmed the suitability and application of the Langmuir model. Analysis of experimental adsorption data using various kinetic models, such as pseudo-first and second-order models, shows the applicability of the first-order equation. The results showed that in the optimal conditions, the removal percentage was about 95% for AO7 and 80% for MB, which indicates the successful performance of the synthetic film compared to the method. [ABSTRACT FROM AUTHOR]

In this paper, a room-temperature NO2 sensor based on a polyaniline (PANI)/black phosphorus (BP) composite material was proposed to solve the power consumption problem of traditional metal-oxide sensors operating at high temperatures. PANI was synthesized by chemical oxidative polymerization, whereas BP was synthesized by low-pressure mineralization. The PANI/BP composite materials were prepared via ultrasonic exfoliation and mixing. Various characterization techniques, including scanning electron microscope (SEM), X-ray diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), and X-ray photoelectron spectroscopy (XPS), confirmed the successful preparation of the PANI/BP composites and their excellent structural properties. The sensor demonstrated outstanding gas sensitivity in the NO2 concentration range of 2–60 ppm. In particular, the sensor showed a response exceeding 2200% at 60 ppm NO2 concentration when using a 1:1 mass ratio of PANI to BP in the composite material. [ABSTRACT FROM AUTHOR]

In this study, we report a novel synthesis technique for polysaccharides and conducting polymer composites. A series of polysaccharide/polyaniline composites were prepared via double-step polymerization by a sol–gel method developed herein. The chemical structure and the electronic properties of the composites were analyzed through Fourier transform infrared, ultraviolet–visible, and electron spin resonance spectroscopies. Composites with long effective conjugation lengths were obtained because the gelatinized polysaccharide acted as a template and host for the composite. [ABSTRACT FROM AUTHOR]