Search

This review proposes to carry out a state-of-the-art associated with micro-arc oxidation. Firstly, the different aspects of the growth mechanisms of the oxides are detailed. Then, the formation of micro-arcs and the case of soft-spark treatment are discussed. Then, the electrolytic reactions involved in the layer construction are outlined. We focused on the influence of aluminium alloys on the appearance of the coating and its characteristics before considering the electrolyte formulation. We have concentrated some of our efforts on silicate-based electrolytes, mainly used in research and industry. The importance of electrical parameters in layer formation is detailed later. The main factors studied in the literature are the current source, current density, treatment frequency and duration, and duty cycle. We have also noted the different phase compositions identified in the literature. Finally, since the process is particularly advantageous for protecting the surfaces of aluminium parts against wear, we conclude this review by presenting work on the tribological properties of this coating. In this final section, we highlight the work on the wear-reducing properties and tribological mechanisms identified in the literature. Particular attention is paid to the relationship between the nature of the substrates used, the role of the electrolyte and the counterpart choice on the friction and wear results. [ABSTRACT FROM AUTHOR]

Optimising the performance of materials requires, among other things, the characterisation of residual stresses during the design stage. Raman spectroscopy offers access to these residual stresses at the micrometre scale when this inelastic light scattering is active in these materials. In this case, the relationship between the Raman mode shift and the pressure must be known. High-pressure cells with diamond anvils or bending instruments coupled to Raman spectrometers are habitually used to determine this relationship. In this article, we propose a new method that involves a Hertzian contact to obtain this relationship. A device that compresses an alumina ball against a transparent glass plane is connected to a Raman spectrometer. Under these conditions, the contact pressure can be as high as 1.5 GPa. The contact between the glass plane and the ball is observed through a diaphragm. Several hundred Raman spectra are recorded depending on the contact diameter. The spectral profiles obtained represent the shift in the Raman modes of alumina and glass along the contact diameter. Hertz's theory accurately describes the pressure profile as a function of position for elastic materials. Therefore, the contact diameter can be measured by fitting the spectral profile with a function identical to the Hertz profile. We then deduce the maximum pressure. Next, the calculated pressure profile along the contact diameter is correlated with the spectral profile. We obtain a pressure dependence of the Raman mode with a coefficient equal to 2.07 cm − 1 /GPa for the Eg modes of alumina at 417 cm − 1 , which is in good agreement with the literature. In the case of glass, we refine the measurement of the Q3 mode shift at 1096 cm − 1 in the studied pressure range compared to the literature. We find a coefficient of 4.31 cm − 1 /GPa. This work on static contacts opens up promising prospects for investigations into dynamic contacts in tribology. [ABSTRACT FROM AUTHOR]

The tribological behavior of a steel/glass ball-on-flat contact was studied by synchronizing the friction measurements with an acoustic emission device and a vision system. The results highlight two distinct friction regimes identified with low and high friction values. Their transition is characterized by a modification of acoustic emission signals. In addition, two main damage and wear mechanisms are identified: the creation and propagation of Hertzian cracks visible on the glass surface and the constitution of an interfacial layer of debris. The different accommodation mechanisms, activated successively or simultaneously, are identified for acoustic emission frequencies between 300 and 700 kHz. Eventually, this approach allows a real-time wear mechanisms identification and gives better insights about acoustic emission signals in relation to tribological systems. [ABSTRACT FROM AUTHOR]

The quality of friction stir welding joints is intimately related to the correct mixing of the stirred material. The material flow is strongly dependent on the plastic behavior of the welded alloy. For this reason, the friction stir weldability depends on the structure, microstructure, and chemical composition of the base material. In this work, in-plane forces and acoustic emission signals were monitored while welding two heat-treatable aluminum alloys. The force evolutions suggested possible continuous and intermittent material flow during friction stir welding depending on the welding parameters. The differences observed in the in-plane forces were corroborated by acoustic emission, confirming the modification in the material flow phenomenology. Therefore, differences observed in aluminum alloys' friction stir weldability are due to the plastic behavior at high temperature and medium-high strain rate. The higher the deformability of the aluminum alloys, the wider the weldability window in friction stir welding because of continuous material flow in an extended range of process parameters. [ABSTRACT FROM AUTHOR]

This paper deals with the development of an original apparatus called TRIBOLUMEN designed specifically for friction experiments on transparent materials. The friction measurement is synchronized with an acoustic emission (AE) sensor and the device is also equipped with a high-speed camera offering a direct view at the interface to gain a deeper understanding of tribological mechanisms. The TRIBOLUMEN device is in ball-on-flat contact configuration with a range of strokes from 5 to 500 µm and an oscillation frequency from 5 to 600 Hz. The experiments showed that this device has an adequate rigidity and can detect subtle friction modifications of the oscillating contacts. The observation of a steel-on-glass contact in real-time highlighted the initiation of Hertzian cracks followed by the formation of debris in the contact. Using the synchronous measurement, these mechanisms were clearly associated with different stages in the friction measurement and in the AE signals, which permitted to identify the AE signature of Hertzian cracks. [ABSTRACT FROM AUTHOR]