Search

In daily life, some traditional interactive modes, such as keyboards and touch pads, still have a strong vitality and practical value.[[179], [571], [573]] Based on different physical transduction mechanisms, these keyboards or touch pads are essentially tactile sensors that transduce the physical touches into electrical signals and map them to corresponding positioning units.[[572], [574]] Converting physical movement into electrical signal is the original intention of TENG, which addresses the power/energy challenges of devices with powerful sensors nowadays.[555] Therefore, the self-powered TENG technology is exactly a good solution for developing a tactile sensor equipped on these devices.[[538], [540], [574], [576], [578]] In these applications, XY matrix scheme greatly reduces the number of channels and is conducive to high resolution wiring layout.[[575], [578]] In this scheme, crosstalk and target sensing resolution are the problems. This could improve the performance of HP-based piezoelectric device for mechanical energy harvesting, design of the photoferroelectric and photopiezoelectric devices, developing hybrid energy harvesters for multi-source energy harvesting, and developing eco-friendly, flexible, and high-performance devices. Early design of such an energy-aware interface (EAI) mainly consists of a voltage detector and a switch.[[506]] Once the voltage across the supercapacitor exceeds the threshold voltage of the voltage detector, the switch will be turned on to connect the wireless sensor system to the supercapacitor. [Extracted from the article]

Recent experiments with a carbon nanotube (CNT) system confirmed that the innertube can oscillate back-and-forth even under a room-temperature excitation. This demonstration of relative motion suggests that it is now feasible to build a CNT-based molecular memory cell (MC), and the key to bring the concept to reality is the precision control of the moving tube for sustained and reliable read/write (RW) operations. Here, we show that by using a 2-section outertube design, we are able to suitably recalibrate the system energetics and obtain the designed performance characteristics of a MC. Further, the resulting energy modification enables the MC to operate as a non-volatile memory element at room temperatures. Our paper explores a fundamental understanding of a MC and its response at the molecular level to roadmap a novel approach in memory technologies that can be harnessed to overcome the miniaturization limit and memory volatility in memory technologies. [ABSTRACT FROM AUTHOR]

Aerosol-jet printing allows functional materials to be printed from inks with a wide range of viscosities and constituent particle sizes onto various substrates, including the printing of organic thermoelectric materials on flexible substrates for low-grade thermal energy harvesting. However, these materials typically suffer from relatively poor thermoelectric performance, compared to traditional inorganic counterparts, due to their low Seebeck coefficient, S, and electrical conductivity, σ. Here, we demonstrate a modified aerosol-jet printing technique that can simultaneously incorporate well-dispersed high-S Sb2Te3 nanoflakes and high-σ multi-walled carbon nanotubes (MWCNTs) providing good inter-particle connectivity to significantly enhance the thermoelectric performance of poly(3,4-ethylenedioxythiophene) polystyrene sulfonate structures on flexible polyimide substrates. A nominal loading fraction of 85 wt. % yielded a power factor of ∼41 μW/mK2, which is among the highest for printed organic-based structures. Rigorous flexing and fatigue tests were performed to confirm the robustness and stability of these aerosol-jet printed MWCNT-based thermoelectric nanocomposites. [ABSTRACT FROM AUTHOR]

A self-powered, sliding electrification based quasi-static triboelectric sensor (QS-TES) for detecting angle from rotating motion is reported. This innovative, cost-effective, simply-designed QS-TES has a two-dimensional planar structure, which consists of a rotator coated with four channel coded Cu foil material and a stator with a fluorinated ethylenepropylene film. On the basis of coupling effect between triboelectrification and electrostatic induction, the sensor generates electric output signals in response to mechanical rotating motion of an object mounted with the sensor. The sensor can read and remember the absolute angular position, angular velocity, and acceleration regardless being continuously monitored or segmented monitored. Under the rotation speed of 100 r min−1, the output voltage of the sensor reaches as high as 60 V. Given a relatively low threshold voltage of ±0.5 V for data processing, the robustness of the device is guaranteed. The resolution of the sensor is 22.5° and can be further improved by increasing the number of channels. Triggered by the output voltage signal, the rotating characteristics of the steering wheel can be real-time monitored and mapped by being mounted to QS-TES. This work not only demonstrates a new principle in the field of angular measurement but also greatly expands the applicability of triboelectric nanogenerator as self-powered sensors. [ABSTRACT FROM AUTHOR]

A new membrane-based triboelectric sensor (M-TES) is presented as a self-powered pressure change sensor. It generates a voltage induced by surface triboelectric charges in response to an air pressure change. Extremely high detection resolutions of 0.34 Pa and 0.16 Pa are achieved when the air pressure increases and decreases in a small region away from the ambient standard atmosphere pressure, respectively, indicating an excellent sensitivity. By integrating the M-TES with a signal processing unit, we demonstrate practical applications of the device in sensing footsteps, respirations, and heartbeat, which suggests widespread use of the M-TES in fields of security surveillance, chemical engineering, geography research, environment monitoring, and personal healthcare. [ABSTRACT FROM AUTHOR]

The applications of a single-layer triboelectric nanogenerator (TENG) may be challenged by its lower output current, and a possible solution is to use three-dimensional (3D) integrated multilayered TENGs. However, the most important point is to synchronize the outputs of all the TENGs so that the instantaneous output power can be maximized. Here, a multi-layered stacked TENG is reported as a cost-effective, simple, and robust approach for harvesting ambient vibration energy. With superior synchronization, the 3D-TENG produces a short-circuit current as high as 1.14 mA, and an open-circuit voltage up to 303 V with a remarkable peak power density of 104.6 W m−2. As a direct power source, it is capable of simultaneously lighting up 20 spot lights (0.6 W ea.) as well as a white G16 globe light. Furthermore, compared with the state-of-the-art vibration energy harvesters, the 3D-TENG has an extremely wide working bandwidth up to 36 Hz in low frequency range. In addition, with specific dimensional design, the 3D-TENG is successfully equipped inside a ball with a diameter of 3 inches, using which 32 commercial LEDs are simultaneously lighted up via hand shaking, exhibiting great potential of scavenging the abundant but wasted kinetic energy when people play basketball, football, baseball, and so on. [ABSTRACT FROM AUTHOR]

Biosensors are powerful analytical tools for biology and biomedicine, with applications ranging from drug discovery to medical diagnostics, food safety, and agricultural and environmental monitoring. Typically, biological recognition receptors, such as enzymes, antibodies, and nucleic acids, are immobilized on a surface, and used to interact with one or more specific analytes to produce a physical or chemical change, which can be captured and converted to an optical or electrical signal by a transducer. However, many existing biosensing methods rely on chemical, electrochemical and optical methods of identification and detection of specific targets, and are often: complex, expensive, time consuming, suffer from a lack of portability, or may require centralised testing by qualified personnel. Given the general dependence of most optical and electrochemical techniques on labelling molecules, this review will instead focus on mechanical and electrical detection techniques that can provide information on a broad range of species without the requirement of labelling. These techniques are often able to provide data in real time, with good temporal sensitivity. This review will cover the advances in the development of mechanical and electrical biosensors, highlighting the challenges and opportunities therein. [ABSTRACT FROM AUTHOR]

Thermoelectric generators (TEGs) operate in the presence of a temperature gradient, where the constituent thermoelectric (TE) material converts heat into electricity via the Seebeck effect. However, TE materials are characterized by a thermoelectric figure of merit (ZT) and/or power factor (PF), which often has a strong dependence on temperature. Thus, a single TE material spanning a given temperature range is unlikely to have an optimal ZT or PF across the entire range, leading to inefficient TEG performance. Compositionally graded organic–inorganic nanocomposites are demonstrated, where the composition of the TE nanocomposite can be systematically tuned along the length of the TEG, in order to optimize the PF along the applied temperature gradient. The nanocomposite composition is dynamically tuned by an aerosol‐jet printing method with controlled in situ mixing capability, thus enabling the realization of such compositionally graded thermoelectric composites (CG‐TECs). It is shown how CG‐TECs can be realized by varying the loading weight percentage of Bi2Te3 nanoparticles or Sb2Te3 nanoflakes within an organic conducting matrix using bespoke solution‐processable inks. The enhanced energy harvesting capability of these CG‐TECs from low‐grade waste heat (<100 °C) is demonstrated, highlighting the improvement in output power over single‐component TEGs. [ABSTRACT FROM AUTHOR]

Modern electronic devices, particularly those intended for wearable or human health monitoring applications, require high levels of flexibility and stretchability. Hence devices, as well as interconnects, need to be capable of retaining functionality even when being mechanically deformed. Most approaches towards achieving this rely on printing or transferring structures onto elastomeric substrates that can withstand stretching. However, the processing involved can often be cumbersome, and the structures themselves tend to suffer from poor fatigue and/or are limited by the mechanical properties of the underlying substrate. Here, we have developed a novel aerosol jet printing technique capable of building fully freestanding functional structures layer by layer, which are robust and reliable upon thousands of stretching cycles. The process involves printing a combination of layers of different materials with the desired functionality, onto a substrate coated with a sacrificial film that is subsequently dissolved to release the printed structure. Using this method, we demonstrate freestanding conductive wires that can be used as stretchable interconnects/electrodes, and that also function as strain‐sensors. Additionally, we show that a freestanding capacitive structure functions as a robust, stretchable humidity sensor, paving the way for the development of other multilayer, multifunctional stretchable devices and sensors. [ABSTRACT FROM AUTHOR]

Triboelectric motion sensors, based on the generation of a voltage across two dissimilar materials sliding across each other as a result of the triboelectric effect, have generated interest due to the relative simplicity of the typical grated device structures and materials required. However, these sensors are often limited by poor spatial and/or temporal resolution of motion due to limitations in achieving the required device feature sizes through conventional lithography or printing techniques. Furthermore, the reliance on metallic components that are relatively straightforward to pattern into fine features limits the possibility to develop transparent sensors. Polymers would allow for transparent devices, but these materials are significantly more difficult to pattern into fine features when compared to metals. Here, an aerosol‐jet printing (AJP) technique is used to develop triboelectric sensors using a wide variety of materials, including polymers, which can be directly printed into finely featured grated structures for enhanced sensitivity to displacement and speed of motion. A detailed investigation is presented highlighting the role of material selection and feature size in determining the overall resolution of the resulting motion sensor. A three‐channel rotary sensor is also presented, demonstrating the versatility of the AJP technique in developing more complex triboelectric motion sensors. Aerosol‐jet printing is used to develop triboelectric motion sensors, based on the generation of a voltage across two dissimilar materials sliding across each other as a result of the triboelectric effect. A wide variety of materials, including polymers, can be directly printed into fine‐featured grated structures for enhanced sensitivity to displacement and speed of motion. [ABSTRACT FROM AUTHOR]