Search

Green electronics is an emerging topic that requires the exploration of new methodologies for the integration of green components into electronic devices. Therefore, the development of alternative and eco-friendly raw materials, biocompatible and biodegradable, is of great importance. Among these, sodium-alginate is a natural biopolymer extracted from marine algae having a great potential in terms of transparency, flexibility, and conductivity, when functionalized with a thin gold (Au) layer. The electrical transport of these flexible and conducting substrates has been studied, by DC measurements, from 300 to 10 K, to understand the interplay between the organic substrate and the metallic layer. The results were compared to reference bilayers based on polymethyl-methacrylate, a well-known polymer used in electronics. In addition, a detailed investigation of the electric noise properties was also performed. This analysis allows to study the effect of charge carriers fluctuations, providing important information to quantify the minimum metallic thickness required for electronic applications. In particular, the typical noise behavior of metallic compounds was observed in samples covered with 5 nm of Au, while noise levels related to a non-metallic conduction were found for a thickness of 4.5 nm, despite of the relatively good DC conductance of the bilayer. [ABSTRACT FROM AUTHOR]

In this review, the technique of resonant soft X-ray reflectivity in the study of magnetic low-dimensional systems is discussed. This technique is particularly appealing in the study of magnetization at buried interfaces and to discriminate single elemental contributions to magnetism, even when this is ascribed to few atoms. The major fields of application are described, including magnetic proximity effects, thin films of transition metals and related oxides, and exchange-bias systems. The fundamental theoretical background leading to dichroism effects in reflectivity is also briefly outlined. [ABSTRACT FROM AUTHOR]

Herein, we describe the use of soft X-ray reflectivity at the carbon K-edge to study the molecular organization (orientation, structure, and morphology) of pentacene active films in a top-contact transistor geometry. This technique is not affected by sample charging, and it can be applied in the case of insulating substrates. In addition, the sampling depth is not limited to the near-surface region, giving access to buried device interfaces (metal/organic and dielectric/organic). Spectral lineshape simulations, based on ab-initio calculations using a realistic 3D layer-by-layer model, allow us to unravel the details of the molecular organization in all the specific and crucial areas of the active film, overcoming the limitations of conventional approaches. The tilt angle of the long molecular axis in the whole film is found to progressively decrease with respect to the substrate normal from 25° to 0° with the increasing film thickness. A full vertical alignment, optimal for in-plane charge hopping, is reached only after the complete formation of the first five monolayers. Remarkably, starting from the first one in contact with the dielectric substrate, all the monolayers in the stack show a change in orientation with the increasing thickness. On the other hand, at the buried interface with a gold top-contact, the molecules assume a flat orientation that only propagates for two or three monolayers into the organic film. Top-contact devices with the highest performances can thus be obtained using films of at least ten monolayers. This explains the observed thickness dependence of charge mobility in pentacene transistors. [ABSTRACT FROM AUTHOR]

Herein is described a multidisciplinary approach to understand the performance limitations of small molecule organic light emitting transistors (OLETs) based on a layered architecture, an innovative architecture potentially competitive with the state of the art and more flexible for spectral emission control. The processes of charge injection and field-effect transport at metal/organic and organic/organic interfaces are analysed using microscopic and spectroscopic techniques in coordination. Atomic force microscopy and ultrasonic force microscopy are employed to characterize the interface morphology and the initial growth stages of organic films where charge transport actually occurs. X-ray diffraction and near edge X-ray dichroic absorption with linearly polarised light allow to determine the unit cell packing and the molecular orientation at the active organic interfaces, as well as the amount of non-ordered domains. Moreover, chemical reactivity at the interfaces is measured by X-ray photoelectron spectroscopy. It is found that a strong reaction occurs at the metal-organic interfaces, with molecular fragmentation. Additionally, the transport properties strongly depend on the nature of the materials forming the organic stack. Specifically, amorphous conjugated films as bottom layers can promote an increased molecular disorder in the upper active layer, with a concomitant deterioration of the conduction properties. [ABSTRACT FROM AUTHOR]

The relationships between the molecular structure, packing modalities, charge mobility and light emission in organic thin films is a highly debated and controversial issue, with both fundamental and technological implications in the field of organic optoelectronics. Thieno(bis)imide (TBI) based molecular semiconductors provide an interesting combination of good processability, tunable self-assembly, ambipolar charge transport and electroluminescence, and are therefore an ideal test base for fundamental studies on the structure–property correlation in multifunctional molecular systems. Herein, we introduce a new class of thieno(bis)imide quaterthiophenes having alkyl side chains of different shapes (linear, cyclic, branched) and lengths (C1–C8). We found that contrarily to what is generally observed in most molecular semiconductors, the length of the alkyl substituent does not affect the optical, self-assembly and charge transport properties of TBI materials. However, different electroluminescence powers are observed by increasing the alkyl side, this suggesting a potential tool for the selective modulation of TBI functionalities. A deep experimental and theoretical investigation on this new family of TBI materials is provided. [ABSTRACT FROM AUTHOR]

Organic light-emitting transistors (OLETs) are multifunctional optoelectronic devices that hold great promise for a variety of applications, including flat panel displays, integrated light sources for sensing and optical communication systems. The narrow illumination area within the device channel is considered intrinsic to the device architecture and is a severe technological drawback for all those applications where a controlled, wide and homogeneous emission area is required. Here it is shown that not only the position but also the extension of the emission area is voltage-tunable, and the entire channel of the transistor can be homogeneously illuminated. The modeling of the exciton distribution within the channel at the different bias conditions coupled to the modeling of the device emission profile highlights that excitons are spread through the entire channel width and across the bulk of the central emission layer of the p-channel/emitter/n-channel trilayer active heterostructure. [ABSTRACT FROM AUTHOR]

The potential of organic semiconductor-based devices for light generation is demonstrated by the commercialization of display technologies based on organic light-emitting diodes (OLEDs). Nonetheless, exciton quenching and photon loss processes still limit OLED efficiency and brightness. Organic light-emitting transistors (OLETs) are alternative light sources combining, in the same architecture, the switching mechanism of a thin-film transistor and an electroluminescent device. Thus, OLETs could open a new era in organic optoelectronics and serve as testbeds to address general fundamental optoelectronic and photonic issues. Here, we introduce the concept of using a p-channel/emitter/n-channel trilayer semiconducting heterostructure in OLETs, providing a new approach to markedly improve OLET performance and address these open questions. In this architecture, exciton–charge annihilation and electrode photon losses are prevented. Our devices are >100 times more efficient than the equivalent OLED, >2× more efficient than the optimized OLED with the same emitting layer and >10 times more efficient than any other reported OLETs. [ABSTRACT FROM AUTHOR]

This scientific work aims to optimize the preparation of titanium nitride coatings for selective H2 separation using the Reactive High Power Impulse Magnetron Sputtering technology (RHiPIMS). Currently, nitride-based thin films are considered promising membranes for hydrogen. The first series of TiNx/Si test samples were developed while changing the reactive gas percentage (N2%) during the process. Obtained coatings were extensively characterized in terms of morphology, composition, and microstructure. A 500 nm thick, dense TiNx coating was then deposited on a porous alumina substrate and widely investigated. Moreover, the as-prepared TiNx films were heat-treated in an atmosphere containing hydrogen in order to prove their chemical and structural stability; which revealed to be promising. This study highlighted how the RHiPIMS method permits fine control of the grown layer's stoichiometry and microstructure. Moreover, it pointed out the need for a protective layer to prevent surface oxidation of the nitride membrane by air and the necessity to deepen the study of TiNx/alumina interface in order to improve film/substrate adhesion. [ABSTRACT FROM AUTHOR]

The electric transport properties of flexible and transparent conducting bilayers, realized by sputtering ultrathin gold nanometric layers on sodium–alginate free-standing films, were studied. The reported results cover a range of temperatures from 3 to 300 K. In the case of gold layer thicknesses larger than 5 nm, a typical metallic behavior was observed. Conversely, for a gold thickness of 4.5 nm, an unusual resistance temperature dependence was found. The dominant transport mechanism below 70 K was identified as a fluctuation-induced tunneling process. This indicates that the conductive region is not continuous but is formed by gold clusters embedded in the polymeric matrix. Above 70 K, instead, the data can be interpreted using a phenomenological model, which assumes an anomalous expansion of the conductive region upon decreasing the temperature, in the range from 300 to 200 K. The approach herein adopted, complemented with other characterizations, can provide useful information for the development of innovative and green optoelectronics. [ABSTRACT FROM AUTHOR]

The synthesis and characterization of two thieno(bis)imide based n-type semiconductors with electron mobilities of up to 0.3 cm2 V−1 s−1 are described. The relationships between the electronic features of the π-inner core and the functional properties of the new materials are also discussed. [ABSTRACT FROM AUTHOR]

In this paper a novel approach is presented to prepare flexible and transparent conducting films, whose components can be separated and recovered via a recycling process. The fabrication method is based on low power sputtering of ultrathin gold layers on sodium alginate free‐standing films. The resulting foils are thin, easy to handle, and shape, while showing good conductive properties. In particular, they show excellent resistance to mechanical stress, like bending or rubbing, and are highly stable in ambient atmosphere over several months. Therefore they may represent a very promising candidate to be employed in green electronics, thanks to the reduced energy consumption required for their fabrication, the absence of toxic components or chemicals that are derived from oil, and the possibility to disassemble the devices at the end of their life in environmentally friendly conditions. [ABSTRACT FROM AUTHOR]

In this paper, we present a study of the effects of the influence of the substrate platform on the properties of a three-layer vertical hetero-junction made of thin films of a, o-diperfluorohexyl-4T (DHF4T), a blend of tris(8-hydroxyquinoline)aluminium (Alq3) and 4-(dicyanomethylene)-2-methyl-6-(p-dimethylaminostyryl)-4H-pyran (DCM) and a, o-dihexyl-quaterthiophene (DH4T). The hetero-junction represents the active component of an organic light-emitting transistor (OLET). The substrate platforms investigated in this study are glass/indium-tin-oxide/poly(methyl-methacrylate) (PMMA) and Si++/silicon oxide (SiO2)/PMMA. The first platform is almost completely transparent to light and therefore is very promising for use in OLET applications. The second one has been chosen for comparison as it employs standard microelectronic materials, i.e. Si++/SiO2. We show how different gate materials and structure can affect the relevant field-effect electrical characteristics, such as the charge mobility and threshold voltage. By means of an atomic force microscopy analysis, a systematic study has been made in order to correlate the morphology of the active layers with the electrical properties of the devices. [ABSTRACT FROM AUTHOR]