Search

Sulphate-rich wastewaters can be generated due to (i) use of saline water as secondary-quality water for sanitation in urban environments (e.g. toilet flushing), (ii) discharge of industrial effluents, (iii) sea and brackish water infiltration into the sewage and (iv) use of chemicals, which contain sulphate, in drinking water production. In the presence of an electron donor and absence of oxygen or nitrate, sulphate can be reduced to sulphide. Sulphide can inhibit microbial processes in biological wastewater treatment systems. The objective of the present study was to assess the effects of sulphide concentration on the anaerobic and aerobic physiology of polyphosphate-accumulating organisms (PAOs). For this purpose, a PAO culture, dominated by Candidatus Accumulibacter phosphatis clade I (PAO I), was enriched in a sequencing batch reactor (SBR) fed with acetate and propionate. To assess the direct inhibition effects and their reversibility, a series of batch activity tests were conducted during and after the exposure of a PAO I culture to different sulphide concentrations. Sulphide affected each physiological process of PAO I in a different manner. At 189 mg TS-S/L, volatile fatty acid uptake was 55% slower and the phosphate release due to anaerobic maintenance increased from 8 to 18 mg PO-P/g VSS/h. Up to 8 mg HS-S/L, the decrease in aerobic phosphorus uptake rate was reversible (Ic). At higher concentrations of sulphide, potassium (>16 mg HS-S/L) and phosphate (>36 mg HS-S/L) were released under aerobic conditions. Ammonia uptake, an indicator of microbial growth, was not observed at any sulphide concentration. This study provides new insights into the potential failure of enhanced biological phosphorus removal sewage plants receiving sulphate- or sulphide-rich wastewaters when sulphide concentrations exceed 8 mg HS-S/L, as PAO I could be potentially inhibited. [ABSTRACT FROM AUTHOR]

P-limitation in enhanced biological phosphorus removal (EBPR) systems fed with acetate, has generally been considered as a condition leading to enrichment of organisms of the genotype' Candidatus Competibacter phosphatis' expressing the glycogen-accumulating organisms (GAO) phenotype. Recent studies have demonstrated in short-term experiments that organisms of the genotype ' Candidatus Accumulibacter phosphatis' clade I and II, known to express the polyphosphate-accumulating organisms (PAO) phenotype can switch to the GAO phenotype when poly-P is absent, but are performing the HAc-uptake at lower kinetic rates, where clade I showed the lowest rates. The objective of this study was to verify whether organisms of the genotype ' Candidatus Accumulibacter phosphatis' can also be enriched under P-limiting conditions while expressing a GAO phenotype and more specifically to see which specific clade prevails. A sequencing batch reactor was inoculated with activated sludge to enrich an EBPR culture for a cultivation period of 128 days (16 times the solids retention time) under P-limiting conditions. A mixed culture was obtained comprising of 49 % ' Candidatus Accumulibacter phosphatis' clade II and 46 % ' Candidatus Competibacter phosphatis'. The culture performed a full GAO metabolism for anaerobic HAc-uptake, but was still able to switch to a PAO metabolism, taking up excessive amounts of phosphate during the aerobic phase when it became available in the influent. These findings show that P-limitation, often used as strategy for enrichment of ' Candidatus Competibacter phosphatis', does not always lead to enrichment of only ' Candidatus Competibacter phosphatis'. Furthermore, it demonstrates that ' Candidatus Accumulibacter phosphatis' are able to proliferate in activated sludge systems for periods of up to 128 days or longer when the influent phosphate concentrations are just enough for assimilation purposes and no poly-P is formed. The ' Candidatus Accumulibacter phosphatis' retain the ability to switch to the PAO phenotype, taking up phosphate from the influent as soon as it becomes available. [ABSTRACT FROM AUTHOR]

The activity of sulfate reducing bacteria (SRB) in domestic wastewater treatment plants (WWTP) is often considered as a problem due to HS formation and potential related odour and corrosion of materials. However, when controlled well, these bacteria can be effectively used in a positive manner for the treatment of wastewater. The main advantages of using SRB in wastewater treatment are: (1) minimal sludge production, (2) reduction of potential pathogens presence, (3) removal of heavy metals and (4) as pre-treatment of anaerobic digestion. These advantages are accessory to efficient and stable COD removal by SRB. Though only a few studies have been conducted on SRB treatment of domestic wastewater, the many studies performed on industrial wastewater provide information on the potential of SRB in domestic wastewater treatment. A key-parameter analyses literature study comprising pH, organic substrates, sulfate, salt, temperature and oxygen revealed that the conditions are well suited for the application of SRB in domestic wastewater treatment. Since the application of SRB in WWTP has environmental benefits its application is worth considering for wastewater treatment, when sulfate is present in the influent. [ABSTRACT FROM AUTHOR]

The use of saline water in urban areas for non-potable purposes to cope with fresh water scarcity, intrusion of saline water, and disposal of industrial saline wastewater into the sewerage lead to elevated salinity levels in wastewaters. Consequently, saline wastewater is generated, which needs to be treated before its discharge into surface water bodies. The objective of this research was to study the effects of salinity on the aerobic metabolism of phosphate-accumulating organisms (PAO), which belong to the microbial populations responsible for enhanced biological phosphorus removal (EBPR) in activated sludge systems. In this study, the short-term impact (hours) of salinity (as NaCl) was assessed on the aerobic metabolism of a PAO culture, enriched in a sequencing batch reactor (SBR). All aerobic PAO metabolic processes were drastically affected by elevated salinity concentrations. The aerobic maintenance energy requirement increased, when the salinity concentration rose up to a threshold concentration of 2 % salinity (on a W/ V basis as NaCl), while above this concentration, the maintenance energy requirements seemed to decrease. All initial rates were affected by salinity, with the NH- and PO-uptake rates being the most sensitive. A salinity increase from 0 to 0.18 % caused a 25, 46, and 63 % inhibition of the O, PO, and NH-uptake rates. The stoichiometric ratios of the aerobic conversions confirmed that growth was the process with the highest inhibition, followed by poly-P and glycogen formation. The study indicates that shock loads of 0.18 % salt, which corresponds to the use or intrusion of about 5 % seawater may severely affect the EBPR process already in wastewater treatment plants not exposed regularly to high salinity concentrations. [ABSTRACT FROM AUTHOR]

In the sewage or wastewater treatment plant, biological sulphate reduction can occur spontaneously or be applied beneficially for its treatment. The results of this study can be applied to control SRB in the sewage and WWTP. Therefore, population diversity analyses of SRB for nine activated sludge wastewater treatment plants (WWTP) in the Netherlands and the effect of long-term (months) oxygen exposures on the SRB activity were carried out. T-RFLP and clone sequencing analyses of winter and summer samples revealed that (1) all WWTP have a similar SRB population, (2) there is no seasonal impact (10-20 °C) on the SRB population present in the WWTP and (3) Desulfobacter postgatei, Desulfovibrio desulfuricans and Desulfovibrio intestinalis were the most common and dominant SRB species observed in these samples, and origin from the sewage. Short term activity tests demonstrated that SRB were not active in the aerobic WWTP, but while flushed with N-gas SRB became slightly active after 3 h. In a laboratory reactor at a dissolved oxygen concentration of <2 %, sulphate reduction occurred and 89 % COD removal was achieved. SRB grew in granules, in order to protect themselves for oxygen exposures. SRB are naturally present in aerobic WWTP, which is due to the formation of granules. [ABSTRACT FROM AUTHOR]

Aims: Sulphate-reducing bacteria (SRB) activity is generally considered as inconvenience in domestic wastewater treatment plants (WWTP), but could also be applied beneficially. The competition between SRB and methanogens is a point of concern for stable process design. As limited attention was given to the effect of varying acetate and propionate concentrations on SRB activity, this study focused specially on these substrates. Methods and Results: The research was performed in sequencing batch reactors operated at 20°C and an SRT of 15 days. In the acetate-fed reactor, methanogens became dominant, while in the propionate reactor, SRB were the dominant population. In the mixed-substrate-fed reactor, both substrates were converted by SRB. The dominant SRB population in the mixed-substrate-fed reactor was different from the propionate-fed reactor, but all operational characteristics such as the substrate consumption rate, yield and growth rate were similar. The sludge adapted to propionate could easily switch to an acetate feed procedure. Conclusions: These results indicate that under wastewater temperature of 20°C, the SRB are likely to outcompete methanogens more easily as inferred from pure substrate studies on acetate solely. Significance and Impact of the Study: The present results show that the natural presence of propionate in wastewater allows stable sulphate reduction, which decreases the biogas production, but provides an opportunity for using SRB beneficially in wastewater treatment. [ABSTRACT FROM AUTHOR]

The use of saline water as secondary quality water in urban environments for sanitation is a promising alternative towards mitigating fresh water scarcity. However, this alternative will increase the salinity in the wastewater generated that may affect the biological wastewater treatment processes, such as biological phosphorus removal. In addition to the production of saline wastewater by the direct use of saline water in urban environments, saline wastewater is also generated by some industries. Intrusion of saline water into the sewers is another source of salinity entering the wastewater treatment plant. In this study, the short-term effects of salinity on the anaerobic metabolism of phosphate-accumulating organisms (PAO) and glycogen-accumulating organisms (GAO) were investigated to assess the impact of salinity on enhanced biological phosphorus removal. Hereto, PAO and GAO cultures enriched at a relatively low salinity level (0.02 % W/ V) were exposed to salinity concentrations of up to 6 % (as NaCl) in anaerobic batch tests. It was demonstrated that both PAO and GAO are affected by higher salinity levels, with PAO being the more sensitive organisms to the increasing salinity. The maximum acetate uptake rate of PAO decreased by 71 % when the salinity increased from 0 to 1 %, while that of GAO decreased by 41 % for the same salinity increase. Regarding the stoichiometry of PAO, a decrease in the P-release/HAc uptake ratio accompanied with an increase in the glycogen consumption/HAc uptake ratio was observed for PAO when the salinity increased from 0 to 2 % salinity, indicating a metabolic shift from a poly-P-dependent to a glycogen-dependent metabolism. The anaerobic maintenance requirements of PAO and GAO increased as the salinity concentrations risen up to 4 % salinity. [ABSTRACT FROM AUTHOR]

To assess the feasibility of the Anammox process as a cost-effective post-treatment step for anaerobic sewage treatment, the simultaneous effects of organic carbon source, chemical oxygen demand (COD)/N ratio, and temperature on autotrophic nitrogen removal was studied. In batch experiments, three operating conditions were evaluated at 14, 22 and 30 °C, and at COD/N ratios of 2 and 6. For each operating condition, containing 32±2 mg NH4+-N/L and 25±2 mg NO2--N/L, three different substrate combinations were tested to simulate the presence of readily biodegradable and slowly biodegradable organic matter (RBCOD and SBCOD, respectively): (i) acetate (RBCOD); (ii) starch (SBCOD); and (iii) acetate + starch. The observed stoichiometric NO2--N/NH4+-N conversion ratios were in the range of 1.19-1.43, and the single or simultaneous presence of acetate and starch did not affect the Anammox metabolism. High Anammox nitrogen removal was observed at 22 °C (77-84%) and 30 °C (73-79%), whereas there was no nitrogen removal at 14 °C; the Anammox activity was strongly influenced by temperature, in spite of the COD source and COD/N ratios applied. These results suggest that the Anammox process could be applied as a nitrogen removal post-treatment for anaerobic sewage systems in warm climates. [ABSTRACT FROM AUTHOR]

Seawater toilet flushing, seawater intrusion in the sewerage, and discharge of sulfate-rich industrial effluents elevates sulfate content in wastewater. The application of sulfate-reducing bacteria (SRB) in wastewater treatment is very beneficial; as for example, it improves the pathogen removal and reduces the volume of waste sludge, energy requirement and costs. This paper evaluates the potential to apply biological sulfate reduction using acetate and propionate to saline sewage treatment in moderate climates. Long-term biological sulfate reduction experiments at 10 and 20 °C were conducted in a sequencing batch reactor with synthetic saline domestic wastewater. Subsequently, acetate and propionate (soluble organic carbon) conversion rate were determined in both reactors, in the presence of either or both fatty acids. Both acetate and propionate consumption rates by SRB were 1.9 times lower at 10 °C than at 20 °C. At 10 °C, propionate was incompletely oxidized to acetate. At 10 °C, complete removal of soluble organic carbon requires a significantly increased hydraulic retention time as compared to 20 °C. The results of the study showed that biological sulfate reduction can be a feasible and promising process for saline wastewater treatment in moderate climate. [ABSTRACT FROM AUTHOR]

Nitrification is an integral part of biological nitrogen removal processes and usually the limiting step in wastewater treatment systems. Since nitrification is often considered not feasible at temperatures higher than 40 °C, warm industrial effluents (with operating temperatures higher than 40 °C) need to be cooled down prior to biological treatment, which increases the energy and operating costs of the plants for cooling purposes. This study describes the occurrence of thermophilic biological nitrogen removal activity (nitritation, nitratation, and denitrification) at a temperature as high as 50 °C in an activated sludge wastewater treatment plant treating wastewater from an oil refinery. Using a modified two-step nitrification-two-step denitrification mathematical model extended with the incorporation of double Arrhenius equations, the nitrification (nitrititation and nitratation) and denitrification activities were described including the cease in biomass activity at 55 °C. Fluorescence in situ hybridization (FISH) analyses revealed that Nitrosomonas halotolerant and obligatehalophilic and Nitrosomonas oligotropha (known ammonia-oxidizing organisms) and Nitrospira sublineage II (nitrite-oxidizing organism (NOB)) were observed using the FISH probes applied in this study. In particular, this is the first time that Nitrospira sublineage II, a moderatedly thermophilic NOB, is observed in an engineered full-scale (industrial) wastewater treatment system at temperatures as high as 50 °C. These observations suggest that thermophilic biological nitrogen removal can be attained in wastewater treatment systems, which may further contribute to the optimization of the biological nitrogen removal processes in wastewater treatment systems that treat warm wastewater streams. [ABSTRACT FROM AUTHOR]

There are current concerns about the presence of persistent chemicals in recharge water used in soil aquifer treatment systems. Triclocarban (TCC) has been reported as a persistent, high production volume chemical with the potential to bioaccumulate in the environment. It is also known to have adverse effects such as toxicity and suspected endocrine disruption. This study was carried out to study the fate of TCC in soil aquifer treatment (SAT) through laboratory simulations in a soil column. The system performance was evaluated with regards to TCC influent concentration, sand (column) depth, and residence time. Results obtained confirmed the ability of SAT to reduce TCC concentrations in wastewater. Sorption and biodegradation were responsible for TCC removal, the latter mechanism however being unsustainable. The removal efficiency was found to be dependent on concentration and decreased over time and increased with column depth. Within the duration of the experimental run, TCC negatively impacted on treatment performance through a reduction in COD removals observed in the column. [ABSTRACT FROM AUTHOR]

The Activated Sludge Model No. 3 (ASM3) and Dutch calibration guidelines (STOWA) were evaluated in the modelling of an activated sludge system treating effluents from a large oil refinery. The plant was designed to remove suspended solids, organic matter and nitrogen from wastewater at an average water temperature of 34°C. The plant consists of three tanks in series; the first two tanks operate in on-off aeration mode with pure oxygen for N-removal, whilst extra methanol is added for the denitrification, and the third tank is maintained as constantly aerobic. Calibration was performed based on a simplified influent characterisation and extra batch experiments (nitrification and denitrification). With the adjustment of only four parameters the model proved capable of describing the performance of the plant concerning both the liquid phase and the biomass. The model was further used to analyse possible modifications in the plant layout and optimize operational conditions in order to reduce operating costs. Modelling results indicated reduction in methanol dosage by implementing an idle time between aerobic and anoxic phases. In this way, surplus methanol was prevented from entering during the aerobic period. Moreover, simulations showed that the most cost-effective option regarding the denitrification process was a combined pre-post-denitrification scheme, without the need for enlarging existing basins. It can be concluded that although ASM3 and STOWA guidelines were originally developed for domestic wastewater application at a temperature range of 10 to 20°C, they proved well capable of describing the performance of an oil refinery wastewater treatment plant operating at 34°C. Moreover, the plant model proved useful for optimization of the plant performance regarding operational costs. [ABSTRACT FROM AUTHOR]

This paper presents results of a novel application of coupling the Activated Sludge Model No. 3 (ASM3) and the Anaerobic Digestion Model No.1 (ADM1) to assess a tropical wastewater treatment plant in a developing country (Surat, India). In general, the coupled model was very capable of predicting current plant operation. The model proved to be a useful tool in investigating various scenarios for optimising treatment performance under present conditions and examination of upgrade options to meet stricter and upcoming effluent discharge criteria regarding N removal. It appears that use of plant-wide modelling of wastewater treatment plants is a promising approach towards addressing often complex interactions within the plant itself. It can also create an enabling environment for the implementations of the novel side processes for treatment of nutrient-rich, side-streams (reject water) from sludge treatment. [ABSTRACT FROM AUTHOR]

There are two types of microbial populations described in the literature as being capable of anaerobic storage of acetic acid in activated-sludge processes: the polyphosphate-accumulating organisms (PAO) and the glycogen-accumulating non-polyphosphate organisms (GAO). Both groups use the conversion of glycogen to poly-hydroxyalkanoate to produce ATP and NADH; however, the first group can also produce ATP from polyphosphate (poly- P). No representative pure cultures are available from either group. The question arises: is the observed activity of GAO due to PAO that are depleted in poly- P ? In this study, using a laboratory sequencing batch reactor containing an enriched culture, the ability of the enriched PAO to utilize organic substrate (acetate) anaerobically was investigated under conditions of poly- P limitation and surplus glycogen content of the biomass. This study showed clearly that, under these conditions, almost no acetate was taken up. Furthermore, this strongly suggests that PAO can not use glycogen conversion to poly-hydroxyalkanoate as the sole energy source under anaerobic conditions, which seems to be the restricted to a separate group of GAO. On the basis of the results and literature data, an improved scheme for the anaerobic acetate accumulation is presented. [ABSTRACT FROM AUTHOR]

Biological phosphate removal has become a reliable and well-understood process for wastewater treatment. This review describes the historical development of the process and the most important microbiological and process-engineering aspects. From a microbiological point of view, the role of␣poly(hydroxyalkanoates) as storage material in a dynamic process and the use of polyphosphate as an energy reserve are the most important findings. From a process-engineering point of view, the study of biological phosphate removal has shown that highly complex biological processes can be designed and controlled, provided that the importance of the prevailing microbiological ecological processes is recognised. [ABSTRACT FROM AUTHOR]

This paper describes several techniques and methods for sludge characterization which are recently developed and used in our ongoing research on biological phosphorus removal (BPR): (i) chemical measurementof the poly-hydroxy-alkanoate (PHA) content of the biomass, (ii) bioassay for glycogen determination in BPR systems, (iii) determination of the fraction of denitrifying phosphorus accumulating organisms (DPAOs) in P-removing sludge, (iv) determination of the aerobic and anoxic ATP/NADH2 ratio (delta value) in BPR systems, and (v) determination of the glycogen accumulating organisms (GAOs) / phosphorus accumulating organisms (PAOs) ratio in activated sludge. (C) 1999 Published by Elsevier Science Ltd on Behalf of the IAWQ. All rights reserved. [ABSTRACT FROM AUTHOR]

Glycogen plays an important role in biological phosphorus removal from wastewaters. Existing measurement techniques often overestimate the glycogen content of the biomass due to the presence of glucose and/or other carbohydrates than glycogen in the cell material. As an alternative to conventional methods a bioassay for glycogen determinationin biological phosphorus removal systems was developed. The bioassayis based on the strict stoichiometric coupling between anaerobic acetate uptake and glycogen consumption. In other words, the glycogen concentration of the sludge was determined indirectly by measuring the maximal total acetate uptake by the activated sludge in anaerobic batch tests. The bioassay was successfully tested for the determination of glycogen content of the sludge taken from the lab-scale, acetate-fed, anaerobic-aerobic-settling sequencing batch reactor operating at pH 710.1 and temperature of 20 0C. This determination of glycogen requires that glycogen (not poly-P) is the limiting factor for anaerobicacetate uptake. A method to verify this assumption based on the effect of pH on phosphate/acetate ratio is proposed and used. The bioassay is easy to apply and gives a direct measure of the glycogen contentof bio-P bacteria. but its reliability still needs to be verified atfull-scale biological P-removal plants. ) 1998 IAWQ. Published by Elsevier Science Ltd. [ABSTRACT FROM AUTHOR]