Search

Numerical modeling of divertor configurations with radially or vertically extended, tightly baffled, outer divertor legs has demonstrated the existence of a passively-stable fully detached divertor regime. In the simulations, long-legged divertors provide up to an order-of-magnitude increase in peak power handling capability compared to conventional divertors. The key physics for attaining the passively stable, fully detached regime in these simulations involves the interplay of strong convective plasma transport to the divertor leg outer sidewall, confinement of neutral gas in the divertor volume, geometric effects including a secondary X-point, and atomic radiation. New analysis shows that in this regime the detachment front location is set by the balance between the power entering the divertor leg and the losses to the walls of the divertor channel. Correspondingly, the maximum power that can be accommodated by the divertor, while still staying detached, increases with the poloidal length of the leg. The detached regime access window in terms of input power, density and impurity seeding concentration varies quantitatively depending on divertor geometry and modeling assumptions most specifically, cross-field transport to the side walls. [ABSTRACT FROM AUTHOR]

Extremely intense power exhaust channels are projected for tokamak-based fusion power reactors; a means to handle them remains to be demonstrated. Advanced divertor configurations have been proposed as potential solutions. Recent modelling of tightly baffled, long-legged divertor geometries for the divertor test tokamak concept, ADX, has shown that these concepts may access passively stable, fully detached regimes over a broad range of parameters. The question remains as to how such divertors may perform in a reactor setting. To explore this, numerical simulations are performed with UEDGE for the long-legged divertor geometry proposed for the ARC pilot plant conceptual design—a device with projected heat flux power width () of 0.4 mm and power exhaust of 93 MW—first for a simplified Super-X divertor configuration (SXD) and then for the actual X-point target divertor (XPTD) being proposed. It is found that the SXD, combined with 0.5% fixed-fraction neon impurity concentration, can produce passively stable, detached divertor regimes for power exhausts in the range of 80–108 MW—fully accommodating ARC’s power exhaust. The XPTD configuration is found to reduce the strike-point temperature by a factor of  ∼10 compared to the SXD for small separations (∼1.4) between main and divertor X-point magnetic flux surfaces. Even greater potential reductions are identified for reducing separations to  ∼1 or less. The power handling response is found to be insensitive to the level of cross-field convective or diffusive transport assumed in the divertor leg. By raising the separatrix density by a factor of 1.5, stable fully detached divertor solutions are obtained that fully accommodate the ARC exhaust power without impurity seeding. To our knowledge, this is the first time an impurity-free divertor power handling scenario has been obtained in edge modelling for a tokamak fusion power reactor with of 0.4 mm. [ABSTRACT FROM AUTHOR]

In order to more completely demonstrate the I-mode regime as a compelling fusion reactor operating scenario, the first dedicated attempts at I-mode radiative heat exhaust and detachment were carried out on Alcator C-Mod. Results conclusively show that within the parameter space explored, an I/L back-transition is triggered prior to meaningful reductions in parallel heat flux, , target temperature, and target pressure, at the outer divertor. The exact mechanism for the I/L trigger remains uncertain, but a multi-diagnostic investigation suggests the pedestal regulation physics is impacted promptly by small amounts of N2 seeded into the private flux region. The time delay between when N2 contacts the plasma and the I/L transition is triggered varied from 30–120 ms, approximately 0.7–, and the delay varied inversely with I-mode pedestal-top pressure, p e,95. Power and nitrogen influx scans indicate that the I/L transitions are not linked to excessive bulk-plasma impurity radiation. It is also shown that in the subsequent L-mode following nitrogen seeding, and can be reduced by factors of 10. The I/L transition and L-mode exhaust results using N2 are compared to similar attempts using Ne where such and reductions in L-mode are limited to factors of 2–3. Implications for the I-mode regime are discussed, including needs for follow-up experiments on other facilities. [ABSTRACT FROM AUTHOR]

New data from Alcator C-Mod have extended the range of heat flux measurements and scalings to poloidal magnetic fields above ITER-level. Knowledge of how the scrape-off layer heat flux width (λq) scales with machine parameters is crucial for designing fusion reactors and developing a power exhaust solution. An international database indicated that λq scaled approximately inversely with the poloidal magnetic field (Bp) and had no other significant dependencies. However, reactor-class tokamaks are expected to have at least 50% higher Bp than the maximum of that database (0.8 T). Alcator C-Mod has been the only diverted tokamak capable of operating at reactor-level Bp, up to ~1.3 T. A major focus of the final experimental campaign on Alcator C-Mod was to characterize λq over a wide range of conditions, utilizing a unique array of heat flux sensors with unprecedented spatial resolution and heat flux dynamic range. The heat flux width scaling is found to extend up to Bp ~ 1.3 T in H-mode. Looking across confinement regimes we find the remarkable result that λq exhibits a unified dependence on volume-averaged core plasma pressure (). Within a standard deviation of about 20%, the heat flux width in any of the C-Mod plasmas studied (L-, I-, and H-mode) is proportional to the inverse square root of . It is also found that the standard prescription of representing the target plate heat flux profile as a convolution of exponential and Gaussian functions does not capture the heat flux profile measured in the private zone; a purely exponential decay fits the data better in this region to  >3 orders of magnitude in heat flux dynamic range. [ABSTRACT FROM AUTHOR]

Management of power exhaust will be a crucial task for tokamak fusion reactors. Reactor concepts are often proposed with double-null divertors, i.e. having two magnetic separatrices in an up-down symmetric configuration. This arrangement is potentially advantageous since the majority of the tokamak exhaust power tends to flow to the outer pair of divertor legs at large major radius, where the geometry is favorable for spreading the heat over a large surface area and there is more room for advanced divertor configurations. Despite the importance, there have been relatively few studies of divertor power sharing in near double null configurations and no studies at the poloidal magnetic fields and scrape-off layer power widths anticipated for a reactor. Motivated by this need we have undertaken a systematic study on Alcator C-Mod, examining the effect of magnetic flux balance on the power sharing among the four divertor legs in near double-null plasmas. Ohmic L-modes at three values of plasma current and ICRF-heated enhanced D-alpha (EDA) H-modes and I-modes at a single value of plasma current are explored, producing poloidal magnetic fields of 0.42, 0.62 and 0.85 Tesla. For Ohmic L-modes and ICRF-heated EDA H-modes, we find that the point of equal power sharing between upper and lower divertors occurs remarkably close to a balanced double null. Power sharing amongst the outer (upper versus lower) and inner (upper versus lower) pairs of divertors can be described in terms of a logistic function of magnetic flux balance, consistent with heat flux mapping along magnetic field lines to the outer midplane. Power sharing between inner and outer legs is found to follow a Gaussian-like function of magnetic flux balance with non-zero power to the inner divertors at double null. The overall behavior of H-modes operated near double null and for I-modes operating to within one heat flux e-folding of double null are found similar to Ohmic L-modes, with a significant reduction of power on the inner divertor legs. The results are encapsulated in terms of empirically-informed analytic functions of magnetic flux balance. When combined with magnetic equilibrium control system specifications, these relationships can be used to specify the power flux handling requirements for each of the four divertor target plates. [ABSTRACT FROM AUTHOR]

Halo currents generated during disruptions on Alcator C-Mod have been measured with Langmuir ‘rail’ probes. These rail probes are embedded in a lower outboard divertor module in a closely-spaced vertical (poloidal) array. The dense array provides detailed resolution of the spatial dependence (~1 cm spacing) of the halo current distribution in the plasma scrape-off region with high time resolution (400 kHz digitization rate). As the plasma limits on the outboard divertor plate, the contact point is clearly discernible in the halo current data (as an inversion of current) and moves vertically down the divertor plate on many disruptions. These data are consistent with filament reconstructions of the plasma boundary, from which the edge safety factor of the disrupting plasma can be calculated. Additionally, the halo current ‘footprint’ on the divertor plate is obtained and related to the halo flux width. The voltage driving halo current and the effective resistance of the plasma region through which the halo current flows to reach the probes are also investigated. Estimations of the sheath resistance and halo region resistivity and temperature are given. This information could prove useful for modeling halo current dynamics. [ABSTRACT FROM AUTHOR]

The Alcator C-Mod team has recently developed a feedback system to measure and control surface heat flux in real-time. The system uses real-time measurements of surface heat flux from surface thermocouples and a pulse-width modulated piezo valve to inject low-Z impurities (typically N2) into the private flux region. It has been used in C-Mod to mitigate peak surface heat fluxes  >40 MW m−2 down to  <10 MW m−2 while maintaining excellent core confinement, H98  >  1. While the system works quite well under relatively steady conditions, use of it during transients has revealed important limitations on feedback control of impurity seeding in conventional vertical target plate divertors. In some cases, the system is unable to avoid plasma reattachment to the divertor plate or the formation of a confinement-damaging x-point MARFE. This is due to the small operational window for mitigated heat flux in the parameters of incident plasma heat flux, plasma density, and impurity density as well as the relatively slow response of the impurity gas injection system compared to plasma transients. Given the severe consequences for failure of such a system to operate reliably in a reactor, there is substantial risk that the conventional vertical target plate divertor will not provide an adequately controllable system in reactor-class devices. These considerations motivate the need to develop passively stable, highly compliant divertor configurations and experimental facilities that can test such possible solutions. [ABSTRACT FROM AUTHOR]

The impurity screening response of the high-field side (HFS) scrape-off layer (SOL) to localized nitrogen injection is investigated on Alcator C-Mod for magnetic equilibria spanning lower-single-null, double-null and upper-single-null configurations under otherwise identical plasma conditions. L-mode, EDA H-mode and I-mode discharges are investigated. HFS impurity screening is found to depend on magnetic flux balance and the direction of B  ×   B relative to the most active divertor. Impurity ‘plume’ emission patterns indicate that both parallel and perpendicular (E  ×  B) flows in the SOL contribute to the ‘flushing’ of impurities towards the active divertor, thereby affecting the overall impurity screening behavior. Despite the fact that the HFS SOL is extremely narrow in near-double-null configurations, this SOL is able to screen locally injected nitrogen at least as effectively as the low-field side (LFS) SOL—up to a factor of 10 more effective, depending on specific plasma conditions and whether the magnetic geometry produces parallel flows that work with or against E  ×  B flows. For situations in which the E  ×  B drift of the impurity ions opposes parallel flow toward the primary divertor, HFS impurity screening is found to be least effective. When E  ×  B drifts assist parallel flow toward the primary divertor, HFS impurity screening is found to be very effective. These data support the idea of placing RF actuators and close-fitting wall components on the HFS of the tokamak. With this configuration, near-double-null magnetic topologies may be used for active control of plasma parameters at the antenna/plasma interface for optimal RF coupling, mitigate the generation of local impurities from plasma–material interactions and, taking advantage of favorable plasma flows and good screening properties of the HFS SOL, further minimize the impact of wall-born impurity sources on the plasma core. [ABSTRACT FROM AUTHOR]