Search

The paper describes load and resistance factor design (LRFD) calibration for the resistance factor used in the Stiffness Method internal stability soil failure limit state for geogrid mechanically stabilized earth (MSE) walls. The Stiffness Method was recently adopted in the current American Association of State Highway and Transportation Officials LRFD Bridge Design Specifications in the US, and will appear in the next edition of the Canadian Highway Bridge Design Code. The paper describes the details of the calibration of the soil failure limit state which is unique to the Stiffness Method. Calibration outcomes include consideration of the concept of level of understanding in the selection of nominal load and resistance values which is unique to LRFD foundation engineering practice in Canada. A practical conclusion from these calculations is that if product line-specific creep test data are available to estimate the reinforcement secant creep stiffness used for design, then a resistance factor of 1.0 is reasonable for US practice. If only minimum average roll value tensile strength data are available, then a value of 0.95 is recommended for US practice. For Canadian practice, the corresponding values for typical level of understanding are 0.90 and 0.85, respectively. [ABSTRACT FROM AUTHOR]

Copyright of Canadian Geotechnical Journal is the property of Canadian Science Publishing and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Canadian Journal of Civil Engineering is the property of Canadian Science Publishing and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Canadian Journal of Civil Engineering is the property of Canadian Science Publishing and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Canadian Journal of Civil Engineering is the property of Canadian Science Publishing and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Canadian Geotechnical Journal is the property of Canadian Science Publishing and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Canadian Journal of Civil Engineering is the property of Canadian Science Publishing and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Canadian Journal of Civil Engineering is the property of Canadian Science Publishing and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Canadian Journal of Civil Engineering is the property of Canadian Science Publishing and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

During the past decade, composite steel-free deck bridges came to reality in Canada through the construction of five bridges. The new structural system enables the construction of a concrete deck that is totally devoid of all internal steel reinforcement. Traditionally, reinforced concrete bridge decks are designed to sustain loads in flexure. The steel-free deck bridge system develops internal compressive forces "internal arching," which leads to failure by punching shear at substantially higher loads than the flexural design load. The fibre-reinforced concrete deck is usually attached to the steel girders through flexible shear connectors. These steel girders are transversely tied together by steel straps and cross frames. In this paper, the concept of the new bridge system is briefly discussed. The generations of the deck slabs are introduced. Brief outlines of the bridges built to date with this new technology are presented. A three-dimensional finite element model is then proposed to study the behaviour of the main structural component of the new system. The model is verified against previous experimental results and is used to perform a parametric study on some aspects which are thought to significantly affect the behaviour of the new steel-free deck bridge system.Key words: bridges, composite girders, finite element method, steel-free deck, steel straps.Durant la dernière décennie, les ponts à tablier composé sans acier sont devenus réalité au Canada grâce à la construction de cinq ponts. Ce nouveau système structural permet la construction d'un tablier en béton qui est complètement dépourvu de tout renforcement interne en acier. Traditionnellement, les tabliers de pont en béton armé sont conçus afin de supporter des charges en flexion. Le système de tablier de pont sans acier développe des forces internes en compression « cintrage interne » et résulte en une rupture par poinçonnement en cisaillement pour une charge substantiellement plus grande que les charges en flexion de conception. Le tablier en béton renforcé de fibres est habituellement attaché aux poutres d'acier à l'aide de connexions de cisaillement flexibles. Ces poutres d'acier sont attachées ensemble transversalement à l'aide de liens d'acier et de contreventements. Dans cet article, le concept de ce nouveau système est brièvement discuté. Les générations des tabliers en dalles sont introduites. Un bref aperçu des ponts construits à ce jour avec cette nouvelle technologie est présenté. Un modèle par éléments finis tirdimensionnel est par la suite proposé afin d'étudier le comportement des composants structurels principaux du nouveau système. Le modèle est confronté aux résultats expérimentaux obtenus par d'autres dans le passé. Ensuite, il est utilisé afin de performer une étude paramétrique sur quelques aspects qui sont suspectés d'affecter de façon significative le comportement de ce nouveau système de tablier de pont sans acier.Mots clés : ponts, poutres composées, méthode par éléments finis, tablier sans acier, liens d'acier.[Traduit par la Rédaction] [ABSTRACT FROM AUTHOR]

Copyright of Canadian Journal of Civil Engineering is the property of Canadian Science Publishing and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Canadian Journal of Civil Engineering is the property of Canadian Science Publishing and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)

Copyright of Canadian Journal of Civil Engineering is the property of Canadian Science Publishing and its content may not be copied or emailed to multiple sites or posted to a listserv without the copyright holder's express written permission. However, users may print, download, or email articles for individual use. This abstract may be abridged. No warranty is given about the accuracy of the copy. Users should refer to the original published version of the material for the full abstract. (Copyright applies to all Abstracts.)