Search

Double patterning lithography (DPL) technologies have become a must for today's sub-32 nm technology nodes. Currently, there are two leading DPL technologies: self-aligned double patterning (SADP) and litho-etch-litho-etch (LELE). Among them, SADP has the significant advantage over LELE in its ability to avoid overlay, making it the likely DPL candidate for the next technology node of 14 nm. In any DPL technology, layout decomposition is the key problem. While the layout decomposition problem for LELE has been well studied in the literature, only a few attempts have been made to address the SADP layout decomposition problem. In this paper, we present a polynomial time exact (optimal) algorithm to determine if a given layout has SADP decompositions that do not have any overlay at specified critical edges. The previous approaches tried to minimize the total overlay of a given layout, which may be a problematic objective. Furthermore, all previous exact algorithms were computationally expensive exponential time algorithms based on SAT or ILP. Other previous algorithms for the problem were heuristics without having any guarantee that an overlay-free solution can be found even if one exists. [ABSTRACT FROM AUTHOR]

This paper presents an efficient, scalable, and optimal slack-driven shaping algorithm for soft blocks in nonslicing floorplan. The proposed algorithm is called SDS. SDS is specifically formulated for fixed-outline floorplanning. Given a fixed upper bound on the layout width, SDS minimizes the layout height by only shaping the soft blocks in the design. Iteratively, SDS shapes some soft blocks to minimize the layout height with the guarantee that the layout width would not exceed the given upper bound. Rather than using some simple heuristic as in previous work, the amount of change on each block is determined by systematically distributing the global total amount of available slack to individual block. During the whole shaping process, the layout height monotonically reduces and eventually converges to an optimal solution. Two optimality conditions are presented to check the optimality of a shaping solution for fixed-outline floorplanning. In practice, to terminate the process of convergence early, we propose two different stopping criteria. We also extend SDS to handle other floorplanning problems, e.g., classical floorplanning. To validate the efficiency and effectiveness of SDS, comprehensive experiments are conducted on MCNC and HB benchmarks. Compared with previous work, SDS achieves the best experimental result with a significantly faster runtime. [ABSTRACT FROM AUTHOR]

In synchronous circuit designs, clock skew is difficult to minimize because a single physical layout of a clock tree must satisfy multiple constraints in a complicated power mode environment where certain modules may operate with different voltages. In this paper, we use adjustable delay buffers (ADB) whose delays can be tuned or adjusted to minimize clock skew under different power modes. Assuming that the positions of k ADBs are already determined, we first propose a linear-time optimal algorithm which assigns the values of ADBs so that the skew is optimal among all possible ADB assignments with a possibility of latency penalty. Then, we propose a modified optimal algorithm without latency penalty. We also propose an efficient heuristic to determine good positions for ADBs. Our results show significant improvement when compared to cases without ADBs. [ABSTRACT FROM AUTHOR]

As process technologies advance to the subwavelength era, the 1-D design style is regarded as one of the most effective ways to continue scaling down the minimum feature size. To improve the printability of 1-D cell design, it is essential to insert dummy patterns and optimize line-end gap distribution for each layer. This paper presents novel 1-D cell generation algorithms that simultaneously minimize 1-D cell area and enhance the printability. Experimental results show that the proposed algorithms can effectively and efficiently reduce the number of diffusion gaps, minimize used routing tracks, insert sufficient dummy patterns, and eliminate stage-like line-end gaps without power and timing overhead. Consequently, the 1-D cell area is minimized and the printability of the cell is enhanced. To the best of our knowledge, this is also the first work in the literature that considers line-end gap distribution during 1-D cell generation. [ABSTRACT FROM AUTHOR]

We propose a self-contained, flat, quadratic global placer that is simpler than existing placers and easier to integrate into timing-closure flows. It maintains lower-bound and upper-bound placements that converge to a final solution. The upper-bound placement is produced by a novel look-ahead legalization algorithm. Our placer SimPL outperforms mPL6, FastPlace3, NTUPlace3, APlace2, and Capo simultaneously in runtime and solution quality, running 7.10 times faster than mPL6 (when using a single thread) and reducing wirelength by 3% on the ISPD 2005 benchmark suite. More significant improvements are achieved on larger benchmarks. The new algorithm is amenable to parallelism, and we report empirical studies with SSE2 instructions and up to eight parallel threads. [ABSTRACT FROM PUBLISHER]

A flow is presented for the automatic synthesis of an analog circuit layout based on a schematic and a list of circuit design parameter values. The flow is driven by design, placement, and routing constraints—no layout template is necessary. Every possible layout for each device in the circuit is investigated; the layouts with the best geometric features and smallest quantization error (due to manufacturing grid alignment) are kept. For circuit placement, a complete enumeration of possible circuit placements, limited only by usual constraints of symmetry, proximity, and common centroid, is performed. Out of this enumeration a final circuit placement is selected and routed. The new flow is integrated with a deterministic nonlinear optimization algorithm to perform layout-driven circuit sizing; layouts are synthesized during both gradient approximation and next step determination. Layout-driven circuit sizing was applied to two example circuits. Sizing of the first circuit example took 8\times the amount of CPU time needed for traditional circuit sizing, but remained feasible at 2.1 h of wall clock time on a contemporary workstation. [ABSTRACT FROM PUBLISHER]