Search

The accumulation of plastic packaging wastes in the natural environment highlights the significance of sustainable alternatives. Paper is widely used as a biodegradable packaging material, but poor mechanical strength, barrier properties, and water resistance limit its utility. Typical paper coating materials applied to overcome such drawbacks, such as polyethylene (PE) and ethylene vinyl alcohol (EVOH), are not desirable for sustainability due to environmental persistence. Here, we report a biodegradable, biocompatible, robust, and high-barrier paper coating strategy using boric acid-crosslinked poly(vinyl alcohol) (PVA). Various crosslinked-PVA solutions were prepared using boric acid (BA) and hydrochloric acid (HCl) as a crosslinker and an acid catalyst, respectively. The solutions were coated onto the Kraft paper (KP) through facile bar coating with epichlorohydrin (ECH) as a binder (henceforth referred to as coated papers). The coated papers (KP-P, KP-PB, KP-PBH) show remarkably improved oxygen (∼0.89 cc m−2 d−1) and water vapor (∼5.17 g m−2 d−1) barrier properties as well as tensile strength (∼53.0 MPa) that is retained in moist conditions. The coated papers were significantly mineralized into CO2 (59.2–81.6% over 111 d) in the simulated marine environment biodegradation test. Depolymerization of polymer chains and surface degradation of coated papers are evidenced via FT-IR and SEM, respectively. The microcosm test revealed that the intensive disintegration of the coated papers is synergistically driven by both biotic and abiotic factors (i.e., mechanical stress). Moreover, the in vitro biocompatibility tests employing human embryonic kidney and mouse embryonic fibroblast cells, and in vivo biocompatibility test with mice suggest that the coated papers are highly biocompatible. This work provides a promising strategy for paper packaging that enhances packaging performance without compromising environmental sustainability. [ABSTRACT FROM AUTHOR]

The first step in blood testing necessitates blood separation to obtain an adequate volume of plasma. Traditional centrifugation is bulky, expensive and electricity-powered, which is not suitable for micro-scale blood plasma separation in point-of-care testing (POCT) cases. Microfluidic paper-based plasma separation devices present a promising alternative for plasma separation in such occasions. However, they are limited in terms of plasma yield, which hinders analyte detection. Herein, we proposed a humidity-enhanced paper-based microfluidic plasma separation method to address this issue. Specifically, paper was first treated by blood-typing antibodies, then samples of whole blood were introduced into the prepared paper. After waiting for 5 min for RBC agglutination and plasma wicking under high humidity, micro-scale plasma separation from whole blood was achieved. As a result, an extremely high plasma yield of up to 60.1% could be separated from whole blood through using Xuan-paper. Meanwhile, the purity of plasma could reach 99.99%. Finally, this innovative approach was effortlessly integrated into distance-based glucose concentration detection, enabling rapid determination of blood glucose levels through naked-eye observation. Considering the simplicity and inexpensiveness of this method, we believe that this technology could be integrated to more paper-based microfluidic analytical devices for rapid and accurate detection of plasma analytes in POCT. [ABSTRACT FROM AUTHOR]

Paper-based microfluidics combined with potentiometric measurement has emerged as an attractive approach for detecting various chemical ionic moieties. Detection of heavy metal ions, using paper substrates as solution sampling and delivery systems remains challenging despite efforts to introduce several physico-chemical paper substrate modifications to stop adsorption of ions onto the paper substrates. This study quantitatively investigates the adsorption of heavy metal ions on the paper substrates during paper-based potentiometric measurements and explains the super-Nernstian response of potentiometric sensors through local depletion of heavy metal ions from the solution. Consequently, based on the investigated ion adsorption, a corrective potential protocol was established for the electrodes coupled with paper-based solution sampling by predicting interference free sensor response from paper-based measurement. Furthermore, the ion adsorption was also recorded for mixed metal ion solutions to understand competitive primary/interfering ions adsorption onto the paper substrates and establish corrective measures to predict interference free sensor response. In this method, no modifications of the paper substrates are necessary before actual potentiometric measurements. The proposed corrective protocol allows prediction of sensor response based on the paper-based solution sampling potentiometric measurement, providing a simple methodological approach based on correction of potential readout of the potentiometric sensor, thus completely resigning from the need of modifying paper substrate for measurements of heavy metal ions. [ABSTRACT FROM AUTHOR]

Plastic pollution at the nanoscale continues to pose adverse effects on environmental sustainability and human health. However, the detection of nanoplastics (NPLs) remains challenging due to limitations in methodology and instrumentation. Herein, a "green approach" for surface-enhanced Raman spectroscopy (SERS) was exploited to detect polystyrene nanospheres (PSNSs) in water, employing untreated filter paper and a simple syringe-filtration set-up. This SERS protocol not only enabled the filtration of nano-sized PSNSs, which are smaller than the pore size of the ordinary filter paper, but also offered SERS enhancement by utilizing quasi-spherical-shaped silver nanoparticles (AgNPs) as the SERS-active substrate. The filtering of NPLs was accomplished by adding an aggregating agent to the nanoparticle mixture, which caused the aggregation of NPLs and AgNPs, resulting in a larger cluster and more hot spots for SERS detection. The optimal aggregating agent and its concentration, as well as the volume ratio between the AgNPs and NPLs, were also optimized. This SERS method successfully detected and quantified PSNSs of various sizes (i.e., 100, 300, 460, 600, and 800 nm) down to a limit of detection (LOD) of about 0.31 μg mL−1. The method was also validated against the presence of several interferents (i.e., salts, sugars, amino acids, and surfactants) and was proven practical, as evidenced by the detection of 800nm PSNSs in drinking and tap water (LODs of 1.47 and 1.55 μg mL−1, respectively). [ABSTRACT FROM AUTHOR]

Serum contains rich elemental information, and the elemental analysis of the serum using laser-induced breakdown spectroscopy (LIBS) can help with the diagnosis and treatment of cancer. In this work, serum specimens from breast cancer patients were used as samples, and the elements Mg, Ca, and K were analyzed using LIBS. Silver nanoparticles (Ag NPs) were introduced to enhance spectral emission intensities, and this technique is known as nanoparticle-enhanced LIBS (NELIBS). An Ag NP-coated filter paper (Ag NP paper) substrate was prepared and was compared with silicon and aluminum substrates for NELIBS analysis. The Ag NP paper substrate showed lower spectral intensity variances and better elemental distribution uniformity due to the reduced coffee-ring effect compared with silicon and aluminum substrates. The enhanced effect of the Ag NP paper was optimized by adjusting serum volume and Ag NPs concentration. It was found that Mg, Ca, and K required different optimal conditions for spectral enhancement. The highest enhancement factors (EF) for Mg, Ca, and K were 1.85, 1.76, and 3.10, respectively. The electron temperature (Te) and electron number density (Ne) of NELIBS plasmas were measured using the Boltzmann plot and Stark broadening methods and compared with those of the normal LIBS plasmas. The Te and Ne of the NELIBS and normal LIBS samples were generally comparable with each other. Higher Ag NP concentrations led to lower Te values for NELIBS plasmas. [ABSTRACT FROM AUTHOR]

The demand for flexible pressure sensors with high performance is increasing with the growing wearable technology market. According to the developing requirement for green electronics, paper-based sensors, which are more environmentally friendly, have received more and more attention. However, the intrinsic mechanical properties of paper materials limit the sensing performance of paper-based sensors, such as restricted working range and response bandwidth. Herein, a rigid–soft hybrid design strategy is proposed to improve the sensing performance of paper-based pressure sensors, and bioinspired microstructures are introduced into the architecture of sensors for further improvement. As a result, the prepared paper-based pressure sensor has a faster response/recovery speed (<50 ms), a wide sensing range (1 MPa) and frequency response bandwidth (0.05–1000 Hz) and excellent cycling stability (5000 cycles). In addition, the paper-based pressure sensor is superhydrophobic with a water contact angle of 152.62°. Based on the excellent sensing performance and waterproofness, the paper-based pressure sensor can be used as a wearable device for detecting joint movements or gait of humans/robots in both air and underwater. In addition, it can be used to send communication signals, showing great potential for applications in future underwater rescue. [ABSTRACT FROM AUTHOR]

Non-enzymatic electrochemical blood glucose sensors often suffer from issues such as requiring an alkaline environment, limited monitoring range, and poor anti-interference properties. Carbon substrates have been demonstrated to improve the performance of non-enzymatic sensors, but complex and energy-consuming manufacturing processes restrict their use. Herein, a simple and green approach for the preparation of 3D porous Au/Au-Pt networks (PAAPNs) is proposed using tissue paper for recycling as the nanomaterial substrate to deposit Au-Pt bimetallic nanoparticles. The unique structure of the PAAPNs sensor allows for low-potential operation (-1.0 V) with a wide monitoring range (-0.25 to 36 mM) in a neutral environment. Moreover, the sensor exhibited excellent selectivity (<10% response of interference) even without the use of an anti-interference outer membrane. Further investigation using density functional theory (DFT) simulation revealed the synergistic effect between Au and Pt in promoting glucose oxidation. Overall, this work provides a simple and low-carbon footprint method for creating carbon substrates from tissue paper for recycling, offering new opportunities for fabricating novel value-added nanomaterials for medical sensing applications. [ABSTRACT FROM AUTHOR]

Multiple protocols have been reported to fabricate paper-based analytical devices (PADs). However, some of these techniques must be revised because of the instrumentation required. This paper describes a versatile and globally affordable method to fabricate PADs using office paper as a substrate and a laser printing technique to define hydrophobic barriers on paper surfaces. To demonstrate the feasibility of the alternatives proposed in this study, the fabrication of devices for three types of detection commonly associated with using PADs was demonstrated: colorimetric detection, electrochemical detection, and mass spectrometry associated with a paper-spray ionization (PSI-MS) technique. Besides that, an evaluation of the type of paper used and chemical modifications required on the substrate surface are also presented in this report. Overall, the developed protocol was suitable for using office paper as a substrate, and the laser printing technique as an efficient fabrication method when using this substrate is accessible at a resource-limited point-of-need. Target analytes were used as a proof of concept for these detection techniques. Colorimetric detection was carried out for acetaminophen, iron, nitrate, and nitrite with limits of detection of 0.04 μg, 4.5 mg mL−1, 2.7 μmol L−1, and 6.8 μmol L−1, respectively. A limit of detection of 0.048 fg mL−1 was obtained for the electrochemical analysis of prostate-specific antigen. Colorimetric and electrochemical devices revealed satisfactory performance when office paper with a grammage of 90 g m−2 was employed. Methyldopa analysis was also carried out using PSI-MS, which showed a good response in the same paper weight and behavior compared to chromatographic paper. [ABSTRACT FROM AUTHOR]

This report presents an investigation into the use of carbon paper electrodes prepared from chitosan-adhered graphene magnetite nanoparticles for the analysis of Cr(VI). The preparation and storage of carbon paper electrodes is a simple process, and these electrodes are easier to replace than electrodes modified by more conventional methods. The electrochemical detection of Cr(VI) using square wave adsorption cathodic dissolution voltammetry (SWAdCSV) with high selectivity and sensitivity, as well as the optimum conditions for the preparation of the electrodes and the electrode parameters affecting the SWAdCSV signal, were the main points of focus of the investigation. Cr(VI) was detected linearly in the range of 4-40 μg L-1 with a detection limit of 2.84 μg L-1. The electrode output precision, calculated as %RSD, was 7.16% (n = 6), and this was the measurement used for the detection of Cr(VI) in standard and test samples with recoveries between 89% and 114%. The results were consistent with those obtained using the standard UV-Vis spectrophotometric method with a paired t-test at 95% confidence level. [ABSTRACT FROM AUTHOR]

Paper-based ratiometric fluorescence sensors are normally prepared using two or more types of fluorescent materials on a paper chip for simple, low-cost and fast detection. However, the choice of multi-step and one-step modifications on the paper chip affects the analytical performance. Herein, a novel paper-based dual-emission ratiometric fluorescence sensor was designed for the selective detection of tetracycline (TC). Carbon dots (CDs) modified with Eu3+ were combined with a sealed paper-based microfluidic chip by two methods: one-step grafting of CDs-Eu3+ on paper and step-by-step grafting of CDs and Eu3+ on paper. The analytical performance was studied and optimized respectively. The red fluorescence of Eu3+ at 450 nm is enhanced and the blue fluorescence of CDs at 617 nm is quenched by energy transfer in the presence of TC. Under optimal conditions, TC is selectively determined in the linear range from 0.1 μM to 100 μM with a detection limit of 0.03 μM by the step-by-step grafting method. In addition, the sealed paper chip could effectively prevent pollution and volatilization from the reagent. This technique has been used to analyze TC in seafood aquaculture water with satisfactory results. [ABSTRACT FROM AUTHOR]

A simple, rapid chemical coating and patterning method was developed and optimized for paper-based substrates for use in paper spray mass spectrometry (PS-MS). A variety of chlorosilanes were explored for coating paper substrates, and their effectiveness in forming hydrophobic surfaces was characterized via contact angle goniometry, scanning electron microscopy, and energy dispersive X-ray spectroscopy. Trichloromethylsilane was selected as the primary coating agent because of the short time required to produce a hydrophobic surface (contact angle > 130°), as well as the ease of patterning. Patterning was performed using 3D-printed masks and an oxygen/plasma cleaner. Optimal mask thickness and oxygen/plasma cleaning parameters were determined to produce channels varying from 0.5 to 2.5 mm in width. The effectiveness of the patterned substrates for PS-MS was determined via analysis of four antiretrovirals: emtricitabine, lamivudine, efavirenz, and dolutegravir. Calibration curves were made for each antiretroviral at varying channel widths, and the limits of detection and limits of quantification for each drug were determined. These results show that this patterning method results in an average 7.2-fold improvement in sensitivity and an average 190-fold improvement in limits of detection over uncoated paper substrates in a neat matrix. In a proof-of-concept experiment, calibration curves were generated for each antiretroviral in urine. A patterned paper substrate with a 2-mm channel resulted in an average 7.4-fold improvement in sensitivity and an average 18-fold improvement in limits of detection over uncoated paper substrates. [ABSTRACT FROM AUTHOR]

Petroleum-based plastics are useful, but they pose a huge threat to the environment and human health. The development of sustainable cellulose paper materials with excellent mechanical and water-resistance properties to replace plastics is highly desirable but also challenging. Herein, we report a new kind of rosin-based modifier synthesized from fully hydrogenated rosin and (3-glycidoxypropyl)triethoxysilane, which can covalently bind with cellulose fiber networks to improve the hydrophobicity and weaken the capillarity of cellulose paper. The rosin-grafted cellulose composite paper shows a unique combination of water resistance (water absorption of 19.2% and 37.9% in 25 and 90 °C water, respectively) and high strength (tensile strength of 47.9 MPa and Young's modulus of 2.32 GPa). Moreover, the rosin-grafted cellulose composite paper can be completely degraded when buried in soil for up to 100 days, and it can be recycled when treated with an alkali. These impressive performances make rosin-grafted cellulose composite paper a promising eco-friendly alternative material to replace plastics in straws, boxes, cups, bags and so on. [ABSTRACT FROM AUTHOR]

Naphthalenediimide derivative-absorbed papers, which were prepared by dropping chloroform solution, showed fluorescence under photoirradiation after exposure to vapors of small aromatic guests. The fluorescence intensity and maximum wavelength depended on the type of guest aromatic molecules, similar to the crystal. The naphthalenediimide derivative-absorbed papers showed vapochromic and mechanochromic properties. [ABSTRACT FROM AUTHOR]

Microfluidic paper-based analytical devices (microPADs) are emerging as simple-to-use, low-cost point-of-care testing platforms. Such devices are mostly fabricated at present by creating hydrophobic barriers using wax or photoresist patterning on porous paper sheets. Even though devices fabricated using these methods are used and tested with a wide variety of analytes, still they pose many serious practical limitations for low-cost automated mass fabrication for their widespread applicability. We present an affordable and simple two-step process – cut and heat (CH-microPADs) – for the selective fabrication of hydrophilic channels and reservoirs on a wide variety of porous media such as tissue/printing/filter paper and cloth types, such as cotton and polyester, by a lamination process. The technique presents many advantages as compared to existing commonly used methods. The devices possess excellent mechanical strength against bending, folding and twisting, making them virtually unbreakable. They are structurally flexible and show good chemical resistance to various solvents, acids and bases, presenting widespread applicability in areas such as clinical diagnostics, biological sensing applications, food processing, and the chemical industry. Fabricated paper media 96 well-plate CH-microPAD configurations were tested for cell culture applications using mice embryonic fibroblasts and detection of proteins and enzymes using ELISA. With a simple two-step process and minimal human intervention, the technique presents a promising step towards mass fabrication of inexpensive disposable diagnostic devices for both resource-limited and developed regions. [ABSTRACT FROM AUTHOR]

This communication describes the development of polyvinyl chloride electrochemical system in which a paper layer loaded with reagents is inserted into the device, demonstrating a new concept of a paper card-like pad for a reagent-free and easy measurement of the target analyte in solution. This device detects glucose in artificial tears in the range of 0.2–2 mM with a detection limit of 50 μM by simply adding the artificial tears to the paper card-like pad. The novel configuration goes beyond the state of the art, widening the application range of paper in the design of smart analytical devices. [ABSTRACT FROM AUTHOR]

Nucleic acid extraction (NAE) plays a crucial role for diagnostic testing procedures. For decades, dried blood spots (DBS) have been used for serology, drug monitoring, and molecular studies. However, extracting nucleic acids from DBS remains a significant challenge, especially when attempting to implement these applications to the point-of-care (POC). To address this issue, we have developed a paper-based NAE method using cellulose filter papers (DBSFP) that operates without the need for electricity (at room temperature). Our method allows for NAE in less than 7 min, and it involves grade 3 filter paper pre-treated with 8% (v/v) igepal surfactant, 1 min washing step with 1× PBS, and 5 min incubation at room temperature in 1× TE buffer. The performance of the methodology was assessed with loop-mediated isothermal amplification (LAMP), targeting the human reference gene beta-actin and the kelch 13 gene from P. falciparum. The developed method was evaluated against FTA cards and magnetic bead-based purification, using time-to-positive (min) for comparative analysis. Furthermore, we optimised our approach to take advantage of the dual functionality of the paper-based extraction, allowing for elution (eluted disk) as well as direct placement of the disk in the LAMP reaction (in situ disk). This flexibility extends to eukaryotic cells, bacterial cells, and viral particles. We successfully validated the method for RNA/DNA detection and demonstrated its compatibility with whole blood stored in anticoagulants. Additionally, we studied the compatibility of DBSFP with colorimetric and lateral flow detection, showcasing its potential for POC applications. Across various tested matrices, targets, and experimental conditions, our results were comparable to those obtained using gold standard methods, highlighting the versatility of our methodology. In summary, this manuscript presents a cost-effective solution for NAE from DBS, enabling molecular testing in virtually any POC setting. When combined with LAMP, our approach provides sample-to-result detection in under 35 minutes. [ABSTRACT FROM AUTHOR]

Gossypol, a phytotoxicant in cotton-seed oil, has been found to sensitize Tb(III)-luminescence in a supramolecular hydrogel. Based on this observation, a paper-based sensor has been developed to detect gossypol with a limit of detection (LOD) of 2.9 nM. This is the first report of water-based detection with the highest sensitivity involving turn-on time-gated luminescence. This method was also able to sense gossypol in commercial crude cotton-seed oil. [ABSTRACT FROM AUTHOR]

A simple, portable and cost-effective paper-based analysis device is developed for quantitative determination of ascorbic acid (AA) based on the UV-induced oxidation of 3,3′,5,5′-tetramethylbenzidine (TMB). The method does not involve the introduction of any enzyme or external oxidants. More importantly, large equipment is not needed and only a 20 μL sample is needed for each analysis which only takes 8 min. The filter paper is pre-treated with TMB and it turns blue upon UV irradiation because TMB is a self-photosensitizer. The phenol hydroxyl groups of AA can inhibit photo-triggered oxidation resulting in a lighter blue color. The color signal is captured using a smartphone and analyzed using color analysis software. A series of factors that affect the performance of the device are investigated, including the concentration of TMB, buffer pH, channel selection, and irradiation time. The analytical performance is evaluated, and the results show that the method has a wide detection range of 0.05–1.0 mmol L−1 as well as a high selectivity and reproducibility. The proposed method is applied for assaying AA in beverage samples and a VC tablet, and the results correspond to those obtained using the UV method. The results of the recovery test of human serum indicate that the proposed method is feasible in biological samples. This device is easy to fabricate, and convenient to store and transport. It is a truly portable device which has great potential in the on-site assay. [ABSTRACT FROM AUTHOR]

A robust superhydrophobic filter paper was developed through a coating technique, simple and facile, cost-effective, eco-friendly, and defensible, for wide portfolio applications. To develop super hydrophobic filter papers, the paper was coated with inorganic–organic hybrid nanocomposites comprising zinc oxide, chitin, and polycaprolactone (chitin–ZnO–PCL) and zinc oxide, chitosan, and polycaprolactone (chitosan–ZnO–PCL) hybrids through the grafting method. The preparation of a superhydrophobic surface by dip-coating deposition is a facile process. Zinc oxide nanoparticles grafted with chitin–PCL and chitosan–PCL hybrids coated on paper exhibit superhydrophobic properties. Water contact angle measurement carried out using a goniometer showed the average static water angle values of 145° and 160° for the chitin–ZnO–PCL and chitosan–ZnO–PCL grafted hybrid coated surfaces, respectively. The surface morphology of the coating was studied using scanning electron microscopy, X-ray powder diffraction, UV radiation, and Fourier transform infrared spectroscopy. In addition, durability, oil/water separation, bio-degradability, and self-cleaning ability through water flush-out were also studied and reported. The results show that the coated filter papers possess excellent superhydrophobic properties for real-time applications. [ABSTRACT FROM AUTHOR]

A simple and mild stimulus-responsive fluorescent supramolecular polymer network was constructed from a pillararene-based multi-functional monomer through multiple noncovalent interactions and used as a rewritable paper. [ABSTRACT FROM AUTHOR]

Selective enrichment of La(III) by green material as an industrial raw material is of great research interest. In this study, the selective interaction between P and La(III) was utilized, and waste paper (WP) modified with phytic acid (PA) was used to adsorb La(III) from water using a simple one-pot method. The adsorption capacity was 237.23 mg g−1 (30 °C, pH = 5, initial concentration of 200 mg L−1). The equilibrium isotherm fitted the Langmuir isotherm model well. The adsorption equilibrium was reached after 15 min. The adsorption kinetics followed the pseudo-second-order kinetic model, indicating that the adsorption mechanism of the material towards La(III) is single-layer chemisorption. It selectively adsorbed La(III) from four coexisting substances (Pb, Ni, Cu, and Co). After six cycles, the adsorption efficiency of the adsorbent material remained at 60%. [ABSTRACT FROM AUTHOR]

Metal halide perovskite quantum dots (QDs) with unique physicochemical properties are promising candidates for next-generation optoelectronics, but they often suffer from stability issues that severely limit their potential for practical applications. In this work, we adopt an oleic acid/oleylamine-free approach to synthesize MAPbBr3 quantum dot (MQD) papers by incorporating MQDs into cellulose nanofiber frameworks. The abundant long-chain binding ligands containing sulfate terminal groups within the cellulose nanofiber remarkably stabilize the MQD structure, enabling the fabrication of self-power and flexible MQD paper photodetectors with a responsivity of ∼0.19 mA W−1, detectivity of 1.58 × 108 cm Hz1/2 W−1, and excellent bendability and reliability after 500 bending cycles. More importantly, these MQD/cellulose-based self-powered photodetectors demonstrate extraordinarily high environmental stability, maintaining more than 90% of the initial responsivity after 60 days. The simple disposability of the paper-based device is also illustrated by burning within one second, suggesting the ease of device elimination. Our work provides a unique approach to designing ultra-stable perovskite QD-based electronics with unprecedented functionalities. [ABSTRACT FROM AUTHOR]

With growing environmental concern and supply chain uncertainty, now is a fitting time to re-evaluate solvent-free methodologies in forensic chemistry processes. Here, this paper reviews solvent-free approaches for fingermark visualisation, including chemical fuming and vapour phase treatments, dry-transfer treatments, application of heat, and thermal paper specific treatments. After providing historical context, three objectives have been emphasised: identify feasible scenarios for implementing solvent-free methods; showcase the effectiveness of solvent-free methods relative to their nearest solution-based equivalent; and estimate the technological readiness level of each method discussed. Having reviewed the literature, dry-transfer methods of developing latent fingermarks on paper were found to be the most promising and feasible solvent-free approaches for near-term implementation. Such methods make use of standard materials and equipment commonly found in forensic laboratories, are effective at fingermark visualisation, and mitigate most of the pressing issues pertaining to environmental concern and solvent scarcity. [ABSTRACT FROM AUTHOR]

Fast detection of contaminants of emerging concern (CECs) in water resources is of great environmental interest. Ideally, sustainable materials should be used in water quality monitoring technologies implemented for such purposes. In this regard, the application of bio-based materials aimed at the fabrication of analytical platforms has become of great importance. This research merges both endeavors by exploring the application of chitosan-coated paper, decorated with silver nanoparticles (AgNPs), on surface-enhanced Raman scattering (SERS) spectroscopy studies of two distinct types of CECs dissolved in aqueous samples: an antibiotic (ciprofloxacin) and a pesticide (thiram). Our results indicate the superior SERS performance of biocoated substrates compared to their non-coated paper counterparts. The detection limits achieved for thiram and ciprofloxacin using the biocoated substrates were 0.024 ppm and 7.7 ppm, respectively. The efficient detection of both analytes is interpreted in terms of the role of the biopolymer in promoting AgNPs assemblies that result in local regions of enhanced SERS activity. Taking advantage of these observations, we use confocal Raman microscopy to obtain Raman images of the substrates using ciprofloxacin and thiram as molecular probes. We also demonstrate that these biobased substrates can be promising for on-site analysis when used in conjunction with portable Raman instruments. [ABSTRACT FROM AUTHOR]

Sweat, as a sample that includes a lot of biochemical information, is good for non-invasive monitoring. In recent years, there have been an increasing number of studies on in situ monitoring of sweat. However, there are still some challenges for the continuous analysis of samples. As a hydrophilic, easy-to-process, environmentally friendly, inexpensive and easily accessible material, paper is an ideal substrate material for making in situ sweat analysis microfluidics. This review introduces the development of paper as a sweat analysis microfluidic substrate material, focusing on the advantages of the structural characteristics of paper, trench design and equipment integration applications to expand the design and research ideas for the development of in situ sweat detection technology. [ABSTRACT FROM AUTHOR]

"Waste" is "wealth": the transformation of biomass waste into high value-added substances holds significant environmental and economic importance. In our work, orange peel was effectively transformed into valuable fluorescent carbon quantum dots (CQDs) by solvothermal treatment. The resultant CQDs displayed favorable dispersion and a mean particle size of 3.14 ± 0.71 nm. Moreover, these CQDs exhibited a characteristic excitation-dependent fluorescence behavior, which can produce the maximum emission wavelength at 506 nm with excitation at 400 nm. Upon the introduction of permanganate (MnO4−), the fluorescence intensity of CQDs diminished gradually caused by the inner filter effect (IFE) as well as the static quenching effect (SQE). The results revealed that the CQDs can serve as a fluorescent probe, which possessed high performance in terms of sensitivity for quantitative analysis of MnO4−, boasting a low detection limit of 3.31 μM. Subsequently, the application of this fluorescent probe in actual water samples was further explored, resulting in a recovery rate between 98.18% and 101.69%, with relative standard deviations (RSDs) ranging from 1.85% to 2.68%, which was highly satisfactory. The portable paper-based sensor, fabricated by depositing CQDs onto filter paper, is capable of quantitatively and visually detecting MnO4− in combination with a smartphone, thus providing a rapid on-site detection tool for MnO4−. As far as we know, this study provides the inaugural account of a smartphone-based portable sensor for visual determination of MnO4− by using biomass waste based CQDs, suggesting its immense potential for real-time monitoring applications. [ABSTRACT FROM AUTHOR]

We reported a colorimetric paper-based device by integrating the modified acid RNA-cleaving DNAzymes (MaRCD-EC1) for highly sensitive (detection limit = 102 CFU mL−1), and rapid (within 30 min) detection of E. coli without amplification. This device exhibited a clinical sensitivity of 100% and a specificity of 100% in identifying E. coli-associated urinary tract infections (UTIs) using the clinical urine samples. [ABSTRACT FROM AUTHOR]

This paper reports a spin-disc paper-based device with 10 individual detection units containing electromagnetic modules controlling the sample incubation time before chemiluminescence (CL) signal detection. After the sample was added to the top paper chip and incubated with the enzyme, the electromagnet was turned off to allow contact between the top and bottom paper. The H2O2 generated by the sample flowed vertically to the bottom paper and initiated the oxidase of the luminol to generate the CL signal. After one detection the disc was automatically rotated to the next position to repeat the above detection. The advantage of using the device over the lateral flow and the in situ detection was firstly proved using the detection of H2O2 and the glucose/lactate sample with 5 minute incubation. The CL intensity was increased 300 times/1000 times as the glucose/lactate was incubated for 5 minutes compared to the non-incubated samples. Afterward, the device was employed to separately detect glucose and lactate diluted in PBS, artificial sweat, artificial saliva, and fresh cell culture media. Finally, the device was employed to detect the glucose and lactate in the media collected over the 24 hour culture of PC3 cells. The uptake and production rates of glucose and lactate were correspondingly determined as 0.328 ± 0.015 pmol h−1 per cell and 1.254 ± 0.053 pmol h−1 per cell, respectively. The reported device has wide application potential due to its capabilities in automatic detection of multiple samples with very high sensitivity and small sample volume (down to 0.5 μL). [ABSTRACT FROM AUTHOR]

Developing a fluidic platform that combines high-throughput with reconfigurability is essential for a wide range of cutting-edge applications, but achieving both capabilities simultaneously remains a significant challenge. Herein, we propose a novel and unique method for droplet manipulation via drawing surface charge graphics on electrode-free papers in a contactless way. We find that opposite charge graphics can be written and retained on the surface layer of porous insulating paper by a controlled charge depositing method. The retained charge graphics result in high-resolution patterning of electrostatic potential wells (EPWs) on the hydrophobic porous surface, allowing for digital and high-throughput droplet handling. Since the charge graphics can be written/projected dynamically and simultaneously in large areas, allowing for on-demand and real-time reconfiguration of EPWs, we are able to develop a charge-graphic fluidic platform with both high reconfigurability and high throughput. The advantages and application potential of the platform have been demonstrated in chemical detection and dynamically controllable fluidic networks. [ABSTRACT FROM AUTHOR]

A high mortality rate was found in cancer patients with distant metastasis. Development of targeted drugs for effectively inhibiting cancer metastasis is the key for increasing therapeutic success. In the current study, a folding paper system was developed to mimic a tumor–vascular interface for the study of long-distance cell migration. Correlation between the cell migration distance and metastasis-associated gene was successfully analyzed by disassembling the stacked paper construct. The result revealed that the migration distance and number of migrated cells were highly correlated to cell characteristics. Moreover, immunocytochemistry was directly conducted on the paper layer to study the signaling pathway. Kelch-like and protein tyrosine phosphatase families were examined and the PTPN13 gene was shown to regulate long-distance cell migration. By analyzing the phosphorylated mTOR, the PTPN13 gene was further confirmed to be a tumor suppressor gene that inhibits long-distance cell migration. The folding paper system provides an alternative approach for long-distance cell migration. Metastasis-associated gene expression can be analyzed to potentially develop targeted drugs for cancer metastasis inhibition. [ABSTRACT FROM AUTHOR]

As a kind of organic basic compound containing nitrogen, biogenic amine is released from food spoilage and considered as an indicator for monitoring food freshness. Herein, an excellent dual-emission ratiometric fluorescent sensor for eight kinds of biogenic amines was established via the facile mixing of pH-responsive carbon dots and Rhodamine B. The developed sensor shows a rapid response (10 s), low limit of detection (0.733–3.943 μM) and a wide linear range (0–150 μM). More importantly, a portable fluorescent filter paper was prepared by simple dispersing the filter paper in a solution mixture of carbon dots and Rhodamine B. The obtained fluorescent filter paper based sensor showed an obvious color change in the presence of biogenic amine vapor derived from shrimp and mushroom. The results revealed that this sensor could realize the on-site and visual detection of biogenic amines in real food samples, making it suitable for potential application in food safety monitoring. [ABSTRACT FROM AUTHOR]

Paper-based analytical devices (PADs) are very convenient for determining biomarkers in point-of-care (POC) diagnosis while requiring sample pre-treatment or impurity separation. This study reports a novel hydrogel-coupled, paper-based analytical device (PAD) for separation-free H2O2 colorimetric detection in both aqueous solution and cell lysis with sample-to-answer analysis by directly loading into the sample test zone. By encapsulating an inorganic mimic enzyme and chromogenic substrate into the sodium alginate (SA) hydrogel, amplification of the color signal after catalyzing the substrate could be achieved. Taking advantage of the nanoscale porous structure of the hydrogel and the lateral flow channel of the PAD, large interference fragments or bio-macromolecules are prevented from diffusing into the chromogenic reaction, whereas the small target molecules enter the sensing region to trigger the catalytic reaction. This method demonstrated a rapid and accurate analysis with a limit of detection as low as 0.06 mM and detection selectivity. Our proposed device requires no enzyme and is separation-free, portable, easy-to-fabricate, and low-cost, and may offer a platform for quantitative or qualitative analysis of other analytes in body fluids for POC applications. [ABSTRACT FROM AUTHOR]

This study introduces the development of a photothermal-based microfluidic paper analytical device (PT-µPAD) integrated with near-field communication (NFC) technology and smartphone readout for enzyme-free glucose quantification in human samples. With the properties of gold nanoparticles (AuNPs) both as a nanozyme and as a photothermal substrate, there is no need for costly reagents like enzymes or a readout instrumentation for the selective and sensitive detection of glucose. In PT-µPADs, AuNPs are etched by hydrogen peroxide (H2O2) generated from glucose catalysis. Photothermal detection from the plasmonic heating of these AuNPs when illuminated by a 533nm LED light source is achieved by inserting the PT-µPAD sensor into a portable NFC platform suitable for smartphone readout. Temperature variation is directly proportional to the glucose concentration. After optimization, we acquired a linear range between 5.0 and 20.0 µmol L−1 (R2 = 0.9967) and a limit of detection (LOD) of 25.0 nmol L−1 for glucose. Additionally, while our sensor does not utilize any enzyme, it is remarkably selective to glucose with no effects from interferences. Recovery studies in various human control samples indicated a range of 99.73–102.66% with the highest RSD of 3.53%, making it highly accurate and precise. Moreover, our method is more sensitive than other methods relying on conventional µPADs for glucose sensing. By integrating the potential benefits of microfluidics, nanomaterials as nanozymes, and NFC technology for wireless readout, our sensor demonstrates great promise as an accessible, affordable, and shelf-stable device for glucose quantification. Moreover, this concept can be extended to detect other molecules of interest as a point-of-care (POC) diagnostics device. [ABSTRACT FROM AUTHOR]

The document titled "2023 Outstanding Papers published in the Environmental Science journals of the Royal Society of Chemistry" showcases the winners of the Outstanding Paper Awards in environmental science journals. The winners were chosen based on factors like article downloads, Altmetrics, and citations. The document highlights exceptional papers in the field, covering topics such as the removal of PFAS in contaminated soil, the role of sulfuric acid, ammonia, and organics in particle formation over agricultural land, and the association of nanoplastics with human cells. These papers provide valuable insights into environmental concerns and their potential impacts. [Extracted from the article]

A new CdII-based luminescent metal–organic framework (LMOF) with the formula {[Cd(BIBT)(NDC)]·solvents}n (JXUST-32, BIBT = 4,7-bi(1H-imidazol-1-yl)benzo-[2,1,3]thiadiazole and H2NDC = 2,6-naphthalenedicarboxylic acid) was successfully synthesized by a solvothermal method. JXUST-32 shows a two-dimensional (4,4)-connected network and exhibits significant fluorescence red shift and slight enhancement for H2PO4− and CO32− sensing with detection limits of 0.11 and 0.12 μM, respectively. In addition, JXUST-32 has good thermal stability, chemical stability and recyclability. Significantly, JXUST-32 represents a fluorescence red-shift dual response MOF sensor for H2PO4− and CO32− detection and the analytes can be identified by the naked eye, aerosol jet printing filter paper, light-emitting diode beads and luminescent films. [ABSTRACT FROM AUTHOR]

Paper-based microfluidic solution sampling is a viable option for potentiometric sensors to be used for the determination of analytes in samples with high solid-to-liquid ratios. Unfortunately, heavy metal sensitive electrodes cannot be easily integrated with paper-based solution sampling as heavy metals have strong physicochemical adsorption affinity towards paper substrates. In this work, paper substrates were modified with an ion-selective membrane (ISM) cocktail (used for the preparation of Pb2+-ion-selective electrodes (ISEs)) and coupled with model heavy metal Pb2+-ISEs. It was found that the super-Nernstian response of Pb2+-ISEs was eliminated when 10 to 50 mg ml−1 of the ISM cocktail was used for the modification of paper substrates. The modification of the paper substrates by Pb2+-ISM allowed the elimination of adsorption sites. In addition, it resulted in an improvement of sensor performance in terms of their detection limits to be similar to those for conditioned electrodes in standard beaker-based measurements. It is believed that the elimination of super-Nernstian response of the electrodes and improving the potentiometric responses and detection limits of ISEs were attributed to the compatibility improvement of the paper substrates and Pb2+-ISEs to the same type of ISM. [ABSTRACT FROM AUTHOR]

This work demonstrated a quantitative determination of Cu and Zn in tree rings using laser ablation-ICP-MS and the use of quantitative filter paper as a solid support for constructing the calibration curve using aqueous standards. After cleaning the filter paper using 10% v/v HNO3 for 30 min and drying it, 4 μL of standards is delivered on the filter surface and the results are attained with no normalized data. The analytical curves ranged from 0.5 to 10.0 μg g−1 and 5.0 to 100.0 μg g−1 for Cu and Zn, respectively, and the accuracy of the results was checked not only through Certified Reference Materials (NIST 1573a, tomato leaves and 1575a, pine needles) but also using ICP-MS (Inductively Coupled Plasma Mass Spectrometry) as a reference technique. Then, using such minimalist strategies, this method was applied for evaluating the mass fractions of Zn and Cu directly in tree rings. Three parallel ablation lines were drawn with a 220 μm distance between each one, with the same size of the tree ring samples. The average mass fractions for each tree ring and between the 3 ablated lines were at most ca. 18 and 13 μg g−1 for Cu and Zn, respectively, in Hymenaea courbaril, ca. 4 and 9 μg g−1 for Cu and Zn, respectively, in Tipuana tipu, and ca. 160 μg g−1 and