Search

Non-enzymatic electrochemical blood glucose sensors often suffer from issues such as requiring an alkaline environment, limited monitoring range, and poor anti-interference properties. Carbon substrates have been demonstrated to improve the performance of non-enzymatic sensors, but complex and energy-consuming manufacturing processes restrict their use. Herein, a simple and green approach for the preparation of 3D porous Au/Au-Pt networks (PAAPNs) is proposed using tissue paper for recycling as the nanomaterial substrate to deposit Au-Pt bimetallic nanoparticles. The unique structure of the PAAPNs sensor allows for low-potential operation (-1.0 V) with a wide monitoring range (-0.25 to 36 mM) in a neutral environment. Moreover, the sensor exhibited excellent selectivity (<10% response of interference) even without the use of an anti-interference outer membrane. Further investigation using density functional theory (DFT) simulation revealed the synergistic effect between Au and Pt in promoting glucose oxidation. Overall, this work provides a simple and low-carbon footprint method for creating carbon substrates from tissue paper for recycling, offering new opportunities for fabricating novel value-added nanomaterials for medical sensing applications. [ABSTRACT FROM AUTHOR]

Paper-based ratiometric fluorescence sensors are normally prepared using two or more types of fluorescent materials on a paper chip for simple, low-cost and fast detection. However, the choice of multi-step and one-step modifications on the paper chip affects the analytical performance. Herein, a novel paper-based dual-emission ratiometric fluorescence sensor was designed for the selective detection of tetracycline (TC). Carbon dots (CDs) modified with Eu3+ were combined with a sealed paper-based microfluidic chip by two methods: one-step grafting of CDs-Eu3+ on paper and step-by-step grafting of CDs and Eu3+ on paper. The analytical performance was studied and optimized respectively. The red fluorescence of Eu3+ at 450 nm is enhanced and the blue fluorescence of CDs at 617 nm is quenched by energy transfer in the presence of TC. Under optimal conditions, TC is selectively determined in the linear range from 0.1 μM to 100 μM with a detection limit of 0.03 μM by the step-by-step grafting method. In addition, the sealed paper chip could effectively prevent pollution and volatilization from the reagent. This technique has been used to analyze TC in seafood aquaculture water with satisfactory results. [ABSTRACT FROM AUTHOR]

Multiple protocols have been reported to fabricate paper-based analytical devices (PADs). However, some of these techniques must be revised because of the instrumentation required. This paper describes a versatile and globally affordable method to fabricate PADs using office paper as a substrate and a laser printing technique to define hydrophobic barriers on paper surfaces. To demonstrate the feasibility of the alternatives proposed in this study, the fabrication of devices for three types of detection commonly associated with using PADs was demonstrated: colorimetric detection, electrochemical detection, and mass spectrometry associated with a paper-spray ionization (PSI-MS) technique. Besides that, an evaluation of the type of paper used and chemical modifications required on the substrate surface are also presented in this report. Overall, the developed protocol was suitable for using office paper as a substrate, and the laser printing technique as an efficient fabrication method when using this substrate is accessible at a resource-limited point-of-need. Target analytes were used as a proof of concept for these detection techniques. Colorimetric detection was carried out for acetaminophen, iron, nitrate, and nitrite with limits of detection of 0.04 μg, 4.5 mg mL−1, 2.7 μmol L−1, and 6.8 μmol L−1, respectively. A limit of detection of 0.048 fg mL−1 was obtained for the electrochemical analysis of prostate-specific antigen. Colorimetric and electrochemical devices revealed satisfactory performance when office paper with a grammage of 90 g m−2 was employed. Methyldopa analysis was also carried out using PSI-MS, which showed a good response in the same paper weight and behavior compared to chromatographic paper. [ABSTRACT FROM AUTHOR]

This report presents an investigation into the use of carbon paper electrodes prepared from chitosan-adhered graphene magnetite nanoparticles for the analysis of Cr(VI). The preparation and storage of carbon paper electrodes is a simple process, and these electrodes are easier to replace than electrodes modified by more conventional methods. The electrochemical detection of Cr(VI) using square wave adsorption cathodic dissolution voltammetry (SWAdCSV) with high selectivity and sensitivity, as well as the optimum conditions for the preparation of the electrodes and the electrode parameters affecting the SWAdCSV signal, were the main points of focus of the investigation. Cr(VI) was detected linearly in the range of 4-40 μg L-1 with a detection limit of 2.84 μg L-1. The electrode output precision, calculated as %RSD, was 7.16% (n = 6), and this was the measurement used for the detection of Cr(VI) in standard and test samples with recoveries between 89% and 114%. The results were consistent with those obtained using the standard UV-Vis spectrophotometric method with a paired t-test at 95% confidence level. [ABSTRACT FROM AUTHOR]

A simple, rapid chemical coating and patterning method was developed and optimized for paper-based substrates for use in paper spray mass spectrometry (PS-MS). A variety of chlorosilanes were explored for coating paper substrates, and their effectiveness in forming hydrophobic surfaces was characterized via contact angle goniometry, scanning electron microscopy, and energy dispersive X-ray spectroscopy. Trichloromethylsilane was selected as the primary coating agent because of the short time required to produce a hydrophobic surface (contact angle > 130°), as well as the ease of patterning. Patterning was performed using 3D-printed masks and an oxygen/plasma cleaner. Optimal mask thickness and oxygen/plasma cleaning parameters were determined to produce channels varying from 0.5 to 2.5 mm in width. The effectiveness of the patterned substrates for PS-MS was determined via analysis of four antiretrovirals: emtricitabine, lamivudine, efavirenz, and dolutegravir. Calibration curves were made for each antiretroviral at varying channel widths, and the limits of detection and limits of quantification for each drug were determined. These results show that this patterning method results in an average 7.2-fold improvement in sensitivity and an average 190-fold improvement in limits of detection over uncoated paper substrates in a neat matrix. In a proof-of-concept experiment, calibration curves were generated for each antiretroviral in urine. A patterned paper substrate with a 2-mm channel resulted in an average 7.4-fold improvement in sensitivity and an average 18-fold improvement in limits of detection over uncoated paper substrates. [ABSTRACT FROM AUTHOR]

Naphthalenediimide derivative-absorbed papers, which were prepared by dropping chloroform solution, showed fluorescence under photoirradiation after exposure to vapors of small aromatic guests. The fluorescence intensity and maximum wavelength depended on the type of guest aromatic molecules, similar to the crystal. The naphthalenediimide derivative-absorbed papers showed vapochromic and mechanochromic properties. [ABSTRACT FROM AUTHOR]

A simple and mild stimulus-responsive fluorescent supramolecular polymer network was constructed from a pillararene-based multi-functional monomer through multiple noncovalent interactions and used as a rewritable paper. [ABSTRACT FROM AUTHOR]