Search

A rapid and sensitive liquid chromatography tandem mass spectrometry (LC/MS/MS) method for the determination of trace dioctyl sulfosuccinate (DOSS) concentrations in seawater samples has been established. The method is well suited to aquatic environment impact monitoring following application of the dispersant Corexit EC9500A. Linearity of the method was demonstrated down to 0.05 ng/mL−1(0.05 µgL−1) DOSS in seawater, with a 2.4% relative standard deviation precision for preparation replicates. A US EPA method limit of detection of <0.02 ng/mL−1(<0.02 µgL−1) was calculated and specificity was confirmed by monitoring of two qualifier ions at 291.1 m/zand 227.1 m/z. These transitions were confirmed by QToF analysis to be associated with the DOSS precursor ion at 421.2 m/z. For application to seawater samples and samples containing oil particulates, a practical and repeatable calibration range of 0.5 ng/mL−1(0.5 µgL−1) to 25.0 ng/mL−1(25.0 µgL−1) DOSS is reported. The method was shown to have excellent precision and accuracy, with a consistent ≤1.6% relative standard deviation for system suitability standards at 0.5 ng/mL−1(0.5 µgL−1) and linear weighted (1/x) regression coefficients of determination ≥0.995. The surfactant nature of the analyte is discussed in relation to detection limit and loss of analyte. Speculation of a relationship between DOSS in association or aggregation with divalent cations, such as Ca2+present in salt water and hard water, is suggested. The consequent effects on cell ionic balance and membrane function are discussed. [ABSTRACT FROM AUTHOR]

A rapid and sensitive liquid chromatography quadrupole time of flight method has been established for the determination of total naphthenic acid concentrations in aqueous samples. This is the first methodology that has been adopted for routine, high resolution, high throughput analysis of total naphthenic acids at trace levels in unprocessed samples. A calibration range from 0.02 to 1.0 μg mL −1 total Merichem naphthenic acids was validated and demonstrated excellent accuracy (97–111% recovery) and precision (1.9% RSD at 0.02 μg mL −1 ). Quantitative validation was also demonstrated in a non-commercial oil sands process water (OSPW) acid extractable organics (AEOs) fraction containing a higher percentage of polycarboxylic acid isomers than the Merichem technical mix. The chromatographic method showed good calibration linearity of ≥0.999 RSQ to 0.005 μg mL −1 total naphthenic acids with a precision <3.1% RSD and a calculated detection limit of 0.0004 μg mL −1 employing Merichem technical mix reference material. The method is well suited to monitoring naturally occurring and industrially derived naphthenic acids (and other AEOs) present in surface and ground waters in the vicinity of mining developments. The advantage of the current method is its direct application to unprocessed environmental samples and to examine natural naphthenic acid isomer profiles. It is noted that where the isomer profile of samples differs from that of the reference material, results should be considered semi-quantitative due to the lack of matching isomer content. The fingerprint profile of naphthenic acids is known to be transitory during aging and the present method has the ability to adapt to monitoring of these changes in naphthenic acid content. The method's total ion scan approach allows for data previously collected to be examined retrospectively for specific analyte mass ions of interest. A list of potential naphthenic acid isomers that decrease in response with aging is proposed and a quantitative assay of an adamantane carboxylic acid is reported. [ABSTRACT FROM AUTHOR]

Highlights: [•] A GC/MS/MS method for determination of PAHs in soil and sediment is proposed. [•] The method employs direct injection and has no complicated sample preparation steps. [•] The method relies on a GC/MS/MS pseudo-MRM detection technique. [•] We report improved sensitivity and specificity comparable to current techniques for analysis. [Copyright &y& Elsevier]

Abstract: Over the past 20 years, oil sands exploration and processing in Canada have grown steadily, leading to the development of intensive large-scale operations in Alberta, Canada. Naphthenic acids (NAs), a complex mixture of aliphatic and alicyclic carboxylic acids, are by-products of oil sands processing and are known to be toxic. While oil sands processing water (OSPW) is contained in tailings ponds, potential seepage and leaking of OSPW and its contaminants into surrounding surface water systems is a concern. The ability to quantify NAs and their isomers in OSPW surrounding water is essential for monitoring these spills. Unfortunately, quantification of NAs and their isomers is challenging due to the complexity of the NA mixtures, the lack of commercially available standards, and interference from naturally occurring NA compounds. Techniques such as FT-IR and GC/MS are currently used to analyse NAs, but are limited by poor sensitivity and specificity in the case of FT-IR and long sample preparation and instrument run time for GC/MS. To tackle these issues, a rapid LC/MS method was developed which can quickly quantify NAs in surface water with much better sensitivity and specificity than current methods. This method uses large volume injection, ESI negative mode and a Poroshell LC column to improve the method limits of detection (LOD) and quantitation (LOQ). The method is robust and has no complicated sample preparation steps. The method detection limit (MDL) is 0.01mg/L (10ppb) and low limit of quantitation (LLOQ) of 0.1mg/L (100ppb), both for surface water. The developed method was tested with samples from the oil sands producing region, and demonstrated its applicability for fast screening of surface water samples before resorting to costly high accuracy and high resolution mass spectrometry determination. This is the first very rapid LC/MS method using large volume single column direct injection for quantitative determination of naphthenic acids in surface water. [Copyright &y& Elsevier]

An oil spill is a catastrophic event that results in various toxic polycyclic aromatic hydrocarbons (PAHs) entering the environment. Polycyclic aromatic nitrogen heterocycles (PANHs) are more toxic to the environment than their parent PAHs. The high cost and paucity of available PANH standards, the lower abundance of PANHs relative to PAHs, and the difficult separation due to co-elution with PAHs have all contributed to the scarcity of related published literature on the determination of these compounds. To overcome these challenges, a new quantitative method has been successfully developed and validated for the inclusion of 113 polycyclic aromatic carbon (PAC) compounds in a single injection. The 113 compounds consist of PAHs, nitrogen heterocycles, sulfur heterocycles, and alkylated equivalents. Distinct separation of the PANHs and their alkylated counterparts (APANHs) from PAHs was achieved using a gas chromatography quadrupole time-of-flight (GC-QToF) mass spectrometer. The instrument resolved compounds by the high-resolution extraction of monoisotopic masses, allowing response correction factors (RCFs) to be determined from available PANH standards and to calculate concentrations from PAH calibration standards. The developed method was applicable to crude oil samples, generating concentrations of PANHs and relevant information on compound stability for use in oil spill forensics investigation. Development of this practical PAC method provides a powerful tool for screening toxic contaminants, assessing environmental impact, and monitoring recovery following an oil spill. [ABSTRACT FROM AUTHOR]

Determines the individual oligomers of nonylphenol (NP) and its ethoxylate compounds (NPnEo) in marine sediments from the Strait of Georgia, British Columbia. Residues of ethoxylates in over the half of NPnEO inventory sediments; Little degradation of NPnEO in the sediments; Inventory of NPnEO in Fraser River Delta sediments.

• Timber extracts exploited using GC/QToF for chemotyping forensic analysis. • Differentiation and determination of wood achieved at genus/species level. • CITES listed wood species investigated and identified with the new method. • EI wood spectral library suitable for method transfer to routine environmental labs. The international trade in illegally logged and environmentally endangered timber has spurred enforcement agencies to seek additional technical procedures for the identification of wood species. All Dalbergia species are listed under the Convention on International Trade in Endangered Species (CITES) which is the reason this genus was chosen for study. Multiple sources of the heartwood from different Dalbergia species were extracted and chromatographic profiles collected by gas chromatography with high resolution quadrupole Time of Flight mass spectrometry (GC/QToF). The collected data was mined to select peaks and mass ions representative of the investigated Dalbergia species, and used to develop a Microsoft Excel® template offering immediate graphical representation of the results. Using wood specimens sourced from different xylaria, this graphical fingerprint proved adept at definitive identification of Dalbergia species. The CITES Appendix I species, D. nigra , was easily distinguished from D. melanoxylon and look-alike species of other genera. Similarly, a number of other Dalbergia species were differentiated using this current approach. Kernel discrimination analysis (KDA) was applied to increase the confidence of the species identification. The mislabeling of specimens appears to be common, and the emerging technique of GC/QToF in combination with other techniques, offers improved confidence in identification. GC/QToF further provides automation, the dimension of chromatography to avoid interferences, and production of reproducible electron impact positive (EI+) spectra. The prospect of building an EI+ spectral database for future wood identification is an important feature considering the limited accessibility of authenticated wood species specimens. [ABSTRACT FROM AUTHOR]

Oil spill forensic investigations are often challenging due to many confounding variables such as sample weathering, oil composition complexities, and the quality or quantity of collected materials, but the difficulty is further compounded when dealing with mixed oils. In this case, well-established oil fingerprinting techniques become inadequate, including gas chromatography-flame ionization detection (GC/FID) and gas chromatography-mass spectrometry (GC/MS) diagnostic ratio analysis. In dealing with mixtures of highly refined lubricating (lube) oils, GC/FID analysis often yields inconclusive results, while diagnostic ratio analysis can be compromised by missing or low response biomarker compounds. The present study explored the feasibility of addressing the challenges of mixed lube oil analysis through a multi-tiered analytical approach. This analysis supplemented traditional GC/FID and GC/MS diagnostic ratio analyses with multivariate statistics to rapidly screen large data sets. Principal Component Analysis (PCA) and Linear Discriminant Analysis (LDA) proved to be effective and intuitive qualitative methods for visualizing, differentiating, and characterizing four highly similar lube oil mixtures. Non-linear mixing patterns that were significant in the diagnostic ratio analysis were far less evident through LDA. Overall, these findings lay the groundwork for promising future study involving multivariate statistical approaches to complex mixed oil forensic cases. [ABSTRACT FROM AUTHOR]

The atmospheric deposition of polycyclic aromatic compounds (PACs) is considered a major pathway to isolated lakes and bogs in the Athabasca oil sands region (AOSR), Canada. However, the suite of PACs measured has been limited. We report the detailed depositional history of nitrogen and sulphur heterocyclic PACs using a 210Pb dated sediment core (1914–2015) near major developments in the AOSR. We observed (1) an exponential growth in the deposition of heterocyclic PACs to recent times with an average doubling time of 12 years, (2) significant breakpoints in PAC fluxes in the mid to late 1980s, and (3) a synchronous increase of PACs with crude oil production (r2 = 0.82, p = 0.001). NPACs were not detected prior to the 1960s in the sediment core studied, suggesting they may hold promise in serving as indicators for atmospheric PAC deposition of industrial origin. Furthermore, a change in heterocyclic PAC distribution profiles beginning in the 1970–1980s, after the onset of mining, resembling a petcoke signature, was also observed. Significant positive correlations (p < 0.05) were observed between heterocyclic PACs, and several metal(loid)s, including priority pollutant elements, chromium and beryllium, and rare earth elements, cerium, lanthanum and yttrium (r2 > 0.75), suggesting the potential of a common source or similar transport and fate mechanisms. Significant negative or no correlations were observed between heterocyclic PACs and other metal(loid)s, including vanadium, total mercury and lead, possibly reflecting the impact of broader regulatory controls introduced in the mid-1970s on some metal(loids) but not on PACs, including the installation of electrostatic precipitators in major upgrader stacks. Image 1 • Sulphur polycyclic aromatic compounds (PACs) were more abundant than nitrogen PACs. • Sulphur PACs detected since 1930s, while nitrogen PACs not detected before 1960s. • Heterocyclic PACs doubling time of 12 yrs, while routine PACs was between 18 and 25 yrs. • Heterocyclic PAC distribution profiles change began in 1970s post oil sands onset. [ABSTRACT FROM AUTHOR]

Observations made for the analysis of the oil spill dispersant tracer dioctyl sulfosuccinate (DOSS) during LC50 toxicity testing, highlighted a stability issue for this tracer compound in seawater. A liquid chromatography high-resolution quadrupole time-of-flight mass spectrometry (LC/QToF) was used to confirm monooctyl sulfosuccinate (MOSS) as the only significant DOSS breakdown product, and not the related isomer, 4-(2-ethylhexyl) 2-sulfobutanedioate. Combined analysis of DOSS and MOSS was shown to be applicable to monitoring of spill dispersants Corexit® EC9500A, Finasol OSR52, Slickgone NS, and Slickgone EW. The unassisted conversion of DOSS to MOSS occurred in all four oil spill dispersants solubilized in seawater, although differences were noted in the rate of MOSS formation. A marine microcosm study of Corexit EC9500A, the formulation most rapid to form MOSS, provided further evidence of the stoichiometric conversion of DOSS to MOSS under conditions relevant to real world dilbit spill. Results supported combined DOSS and MOSS analysis for the monitoring of spill dispersant in a marine environment, with a significant extension of sample collection time by 10 days or longer in cooler conditions. Implications of the unassisted formation of MOSS and combined DOSS:MOSS analysis are discussed in relation to improving dispersant LC50 toxicity studies. [ABSTRACT FROM AUTHOR]

A saponification extraction method with gas chromatography pseudo-MRM (pMRM) mass spectrometry detection was developed for the determination of 50 total polycyclic aromatic hydrocarbons (TPAH50, a combination of parent and alkylated homologues) in biota. The method was aimed at monitoring and identification of potential TPAH contaminants in bitumen impacted environments. Alkylated PAHs were determined by multi-level, quantitative calibration using parent PAHs. The developed and thoroughly validated method required only one injection for TPAH50 analysis which represents significant saving of time and expensive authentic alkylated standards. The current method was tested with certified reference mussel tissue NIST 1974c and performed well. In a comparison study, the method reached a limit of quantitation (LOQ) for the TPAH50 between 0.1 and 0.2 ng g−1, while the QuEChERs enhanced matrix removal – lipid (EMR) kit produced by Agilent showed an LOQ of 5–10 ng g−1. The current method relied on response factors (RF) for the quantitation of alkylated PAHs determined against parent PAHs. These RFs were shown to be stable and consistent over the course of 1 year, during which over 200 routine environmental biota monitoring samples were analyzed. The environmental biota monitoring samples analyzed include muscle, carcass and liver, with an average total PAH50 concentration of 13, 90 and 135 ng g−1, respectively. Results show significant differences in the distributions of 1 ringed, 2 ringed, 3 ringed, 4 ringed, and 5+ ringed TPAHs between the types of biota samples. [ABSTRACT FROM AUTHOR]

• Unassisted stoichiometric degradation of DOSS to monooctyl sulfosuccinate 2 (MOSS). • LC/QToF method for DOSS and MOSS as dual tracers for oil spill dispersant. • Dispersant plus dilbit in seawater microcosm study of DOSS conversion to MOSS. • Extension of environmental seawater sample collection time. A high resolution mass spectrometry method was developed for the environmental impact monitoring of oil spill dispersants. Previously reported instability of dioctyl sulfosuccinate (DOSS) dispersant tracer was addressed by the new procedure. The method monitors both DOSS and its degradation product, monooctyl sulfosuccinate (MOSS), by liquid chromatography time-of-flight mass spectrometry. The related isomer, 4-(2-ethylhexyl) 2-sulfobutanedioate, was chromatographically resolved from MOSS but was not a product of DOSS degradation. Using this direct injection method (10 μL), the practical lower limit of quantitation was 0.5 nM for each analyte, a concentration equivalent to 0.22 ng mL−1, or 0.30 ng mL−1 including initial dilution factor with acetonitrile. The method was shown applicable to analysis of the dispersants Corexit® EC9500 A, Finasol OSR 52, Slickgone NS, and Slickgone EW for which DOSS is an active ingredient. A marine microcosm study of Corexit EC9500A, together with diluted bitumen (dilbit), at 15 ± 1 °C, provided evidence of the stoichiometric conversion of DOSS to MOSS under conditions reflecting a western Canadian marine environment. The advantage of the developed method is in its ability to extend environmental seawater sample collection time from 4 days for DOSS alone, to 14 days when both DOSS and MOSS are simultaneously analysed and results combined. The collection time is likely extended beyond the 14 day period with cooler temperatures. Preservation of collected seawater samples using sodium hydroxide, converting DOSS into MOSS in situ , was rejected due to stability issues. Addition of disodium ethylenediaminetetraacetic acid did not improve hold times, thus eliminating the theory of cation induced micelle effects causing DOSS loss. [ABSTRACT FROM AUTHOR]

Abstract: The present study investigated oil dispersant toxicity to fish species typical of the cooler regions of Canada, together with less well‐documented issues pertaining to oil dispersant monitoring. The oil dispersant toxicity of Corexit EC9500A was assessed for the freshwater fish species rainbow trout and the seawater species coho, chinook, and chum, with a final median lethal concentration (LC50) acute lethality range between 35.3 and 59.8 mg/L. The LC50 range was calculated using confirmed 0‐h dispersant concentrations that were justified by fish mortality within the first 24 h of exposure and by variability of the dispersant indicator dioctyl sulfosuccinate (DOSS) used to monitor concentrations at later time points. To investigate DOSS as an oil dispersant indicator in the environment, microcosm systems were prepared containing Corexit EC9500A, Finasol OSR52, Slickgone NS, and Slickgone EW dispersants together with diluted bitumen. The DOSS indicator recovery was found to be stable for up to 13 d at 5 °C, 8 d at 10 °C, but significantly less than 8 d at ≥15 °C. After 3 d at temperatures ≥15 °C, the DOSS indicator recovery became less accurate and was dependent on multiple environmental factors including temperature, microbial activity, and aeration, with potential for loss of solvents and stabilizers. A final assessment determined DOSS to be a discrepant indicator for long‐term monitoring of oil dispersant in seawater. Environ Toxicol Chem 2018;37:1309–1319. © 2018 SETAC [ABSTRACT FROM AUTHOR]

The advantage of using naphthenic acid (NA) mixtures for the determination of total NA lies in their chemical characteristics and identification of retention times distinct from isobaric interferences. However, the differing homolog profiles and unknown chemical structures of NA mixtures do not allow them to be considered a traceable reference material. The current study provides a new tool for the comparative assessment of different NA mixtures by direct reference to a single, well-defined and traceable compound, decanoic-d19acid. The method employed an established liquid chromatography time-of-flight mass spectrometry (LC/QToF) procedure that was applicable both to the classic O2 NA species dominating commercial mixtures and additionally to the O4 species known to be present in acid extractable organics (AEOs) derived from oil sands process water (OSPW). Four different commercial NA mixtures and one OSPW-derived AEOs mixture were comparatively assessed. Results showed significant difference among Merichem Technical, Aldrich, Acros, and Kodak commercial NA mixtures with respect to “equivalent to decanoic-d19acid” concentration ratios to nominal. Furthermore, different lot numbers of single commercial NA mixtures were found to be inconsistent with respect to their homolog content by percent response. Differences in the observed homolog content varied significantly, particularly at the lower (n = 9–14) and higher (n = 20–23) carbon number ranges. Results highlighted the problem between using NA mixtures from different sources and different lot numbers but offered a solution to the problem from a concentration perspective. It is anticipated that this tool may be utilized in review of historical data in addition to future studies, such as the study of OSPW derived acid extractable organics (AEOs) and fractions employed during toxicological studies. [ABSTRACT FROM PUBLISHER]

• Long chain fatty acids by liquid chromatography time-of-flight mass spectrometry. • 8 saturated, 7 mono-unsaturated and 16 polyunsaturated fatty acids specific to biofilm. • High resolution with low detection limits in real-world intertidal biofilm samples. • Rapid alkaline methanol aqueous extraction from microphytobenthos. • Survival nutrition for migratory and shorebirds of coastal mudflats The critical importance of mono- and polyunsaturated fatty acids (FAs) in a variety of biological functions, including animal nutrition and as an environmental stress monitor, is well recognized. However, while methods exist for monitoring of fatty acids, few are specific either to the profile of a microphytobenthos matrix or practical in application to multiple, diverse intertidal biofilm sample sets. In the current study, a sensitive liquid chromatography (LC) quadrupole time of flight mass spectrometry (QTOF) method was developed for the quantitative analysis of 31 FAs specific to intertidal biofilm, a thin mucilaginous layer of microalgae, bacteria, and other organisms on the surface of coastal mudflats, which provide a rich source of FAs for migratory birds. Preliminary screening of diverse biofilm samples collected from shorebird feeding grounds highlighted eight saturated (SFA), seven monounsaturated (MUFA), and sixteen polyunsaturated FAs (PUFA) that were selected for analysis. Improved method detection limits in the range 0.3–2.6 ngmL−1 were achieved, excepting for stearic acid at 10.6 ngmL−1. These excellent results were obtained without use of complex sample extraction and clean-up procedures undertaken by other published methods. An alkaline matrix of dilute aqueous ammonium hydroxide with methanol was shown to be selective for extraction and stability of the more hydrophilic fatty acid components. The direct injection method showed excellent precision and accuracy both during validation and application to hundreds of real-world intertidal biofilm samples from the Fraser River estuary (British Columbia, Canada) and other areas of the region frequented by shoreline birds. [ABSTRACT FROM AUTHOR]

• Coho salmon smolts were exposed to marine diesel seawater accommodated fractions. • Cyp1a1 transcripts were more elevated in caudal fin than liver regardless of sex. • Smolts were subsequently moved to clean seawater to monitor depuration over 8 days. • Cyp1a1 elevation returned to basal levels by two days of depuration. • Non-lethal biomonitoring of oil spills and remediation with caudal fin is viable. Oil spills that occur in high traffic coastal environments can have profound consequences for the health of marine ecosystems and the commercial and social interests that are dependent upon these habitats. Given that the global reliance on marine fuels is not abating, it is imperative to develop sensitive and robust tools to monitor oil contamination and remediation in a timely manner. Such tools are increasingly important for ascertaining the immediate and long-term effects of oil contamination on species of interest and local habitats as water-soluble components of oils, such as polycyclic aromatic hydrocarbons (PAHs), can persist post-remediation. We previously demonstrated that 3-methylcholanthrene responsive cytochrome P450–1a (cyp1a1) transcript abundance in the liver and caudal fin of coho salmon smolts (Onchorhynchus kisutch) was sensitive to exposure to low sulfur marine diesel (LSMD) seawater accommodated fractions (seaWAF) in cold water. We expanded upon this paradigm by assessing the utility of the cyp1a1 transcript to track both exposure to LSMD seaWAF and recovery from exposure by measuring cyp1a1 abundance in coho smolts using quantitative polymerase chain reaction (qPCR). Smolts were exposed to either 100 mg/L LSMD seaWAF or clean seawater (control) for 4 days. Fish were then transferred to clean seawater for depuration and tissues sampled at 0, 1, 2, 4, and 8 days from both treatments. Livers and caudal fins were dissected from 40 smolts per group (n total = 400 smolts). The LSMD seaWAF-induced cyp1a1 transcript levels significantly decreased one day after depuration in the liver and caudal fin in a sex-independent manner in genotyped females and males. After four days of depuration, cyp1a1 transcript abundance decreased to baseline control levels, regardless of tissue or sex. The present study demonstrates the value of using the caudal fin as a reliable, sensitive, and non-lethal sampling and monitoring tool. [ABSTRACT FROM AUTHOR]

In current oil spill forensics, diagnostic ratios of hydrocarbon biomarker responses are commonly used to compare oil spill samples to source materials in order to determine the identity of the oil. This well recognized procedure was developed by the European Committee for Standardization (CEN) with corresponding published EN 15522–2 Oil Spill Identification guidelines. However, it is further recognized that weathering can have a negative effect on some of the biomarkers used in the analysis, leading to decreased confidence in the result. In this study, polycyclic aromatic sulfur heterocycles (PASHs) and their alkylated forms (APASHs) were assessed for their potential as additional biomarkers. With the aim of identifying stable PASHs and APASHs useful as weathered oil biomarkers, the superior specificity of gas chromatography with high resolution mass spectrometry was exploited to determine chromatographic peak responses for sixteen petroleum oil samples. Extensive study, involving microcosm extreme weathering and spreadsheet development, led to the identification of 19 new diagnostic ratios based on newly discovered stable PASH and APASH biomarkers. Application of the extended diagnostic ratio suite showed high potential to improve the forensic attribution of post-spill weathered oil back to its original source. [Display omitted] • High resolution mass spectrometer improved spilled oil forensic analysis. • Polycyclic aromatic sulfur heterocycles are important but not well studied. • Loss of aromatic compounds due to weathering is structure dependent. • Three or more ring structures are more stable and suitable as additional biomarkers. • Additional diagnostic ion ratios enhance source oil identification. [ABSTRACT FROM AUTHOR]

Naphthenic acids (NAs) are constituents of oil sands process-affected water (OSPW). These compounds can be both toxic and persistent and thus are a primary concern for the ultimate remediation of tailings ponds in northern Alberta’s oil sands regions. Recent research has focused on the toxicity of NAs to the highly vulnerable early life-stages of fish. Here we examined fathead minnow embryonic survival, growth and deformities after exposure to extracted NA fraction components (NAFCs), from fresh and aged oil sands process-affected water (OSPW), as well as commercially available NA mixtures. Commercial NA mixtures were dominated by acyclic O 2 species, while NAFCs from OSPW were dominated by bi- and tricyclic O 2 species. Fathead minnow embryos less than 24 h old were reared in tissue culture plates terminating at hatch. Both NAFC and commercial NA mixtures reduced hatch success, although NAFCs from OSPW were less toxic (EC50 = 5–12 mg/L, nominal concentrations) than commercial NAs (2 mg/L, nominal concentrations). The toxicities of NAFCs from aged and fresh OSPW were similar. Embryonic heart rates at 2 days post-fertilization (dpf) declined with increasing NAFC exposure, paralleling patterns of hatch success and rates of cardiovascular abnormalities (e.g., pericardial edemas) at hatch. Finfold deformities increased in exposures to commercial NA mixtures, not NAFCs. Thus, commercial NA mixtures are not appropriate surrogates for NAFC toxicity. Further work clarifying the mechanisms of action of NAFCs in OSPW, as well as comparisons with additional aged sources of OSPW, is merited. [ABSTRACT FROM AUTHOR]

Abstract: The Amphibian Metamorphosis Assay (AMA), developed for Xenopus laevis, is designed to identify chemicals that disrupt thyroid hormone (TH)-mediated biological processes. We adapted the AMA for use on an ecologically-relevant North American species, the Pacific tree frog (Pseudacris regilla), and applied molecular endpoints to evaluate the effects of the antibacterial agent, triclosan (TCS). Premetamorphic (Gosner stage 26–28) tadpoles were immersed for 21 days in solvent control, 1.5μg/L thyroxine (T4), 0.3, 3 and 30μg/L (nominal) TCS, or combined T4/TCS treatments. Exposure effects were scored by morphometric (developmental stage, wet weight, and body, snout-vent and hindlimb lengths) and molecular (mRNA abundance using quantitative real time polymerase chain reaction) criteria. T4 treatment alone accelerated development concomitant with altered levels of TH receptors α and β, proliferating cell nuclear antigen, and gelatinase B mRNAs in the brain and tail. We observed TCS-induced perturbations in all of the molecular and morphological endpoints indicating that TCS exposure disrupts coordination of postembryonic tadpole development. Clear alterations in molecular endpoints were evident at day 2 whereas the earliest morphological effects appeared at day 4 and were most evident at day 21. Although TCS alone (3 and 30μg/L) was protective against tadpole mortality, this protection was lost in the presence of T4. The Pacific tree frog is the most sensitive species examined to date displaying disruption of TH-mediated development by a common antimicrobial agent. [Copyright &y& Elsevier]

• Rapid, direct injection LC/MS-QTOF method for resin acids without derivatization. • MDL in range 0.05 to 0.07 µgL−1 for six resin acids in aqueous alkaline matrix. • Precision and accuracy from 1 µgL−1 to 40 µgL−1 in matrix. • Isopimaric as calibrant for six C 20 H 30 O 2 resin acids. • Transferred to LC/MS/MS and successfully applied to environmental samples. A rapid and sensitive liquid chromatography (LC) quadrupole time of flight (QTOF) method has been developed for the determination of resin acid concentrations in aqueous pulp and paper effluent related samples. Calibration R2 of ≥0.995 for twelve resin acids, namely dehydroabietic, 8(14)-abietenic, dihydroisopimaric, levopimaric, neoabietic, pimaric, sandaracopimaric, abietic, isopimaric, palustric, chlorodehydroabietic, and dichlorodehydroabietic acids, was demonstrated in the range 1 µgL−1 to 40 µgL−1. An improved lower limit of quantitation was achieved without use of complex sample extraction and clean-up procedures undertaken by other published methods. Excellent precision and accuracy results were achieved for dehydroabietic, chlorodehydroabietic, dichlorodehydroabietic, isopimaric (integrated inclusive of all C 20 H 30 O 2 resin acids), dihydroisopimaric and 8(14)-abietenic resin acids, with t-99 percentile detection limits spanning the range 0.05 to 0.07 µgL−1. While measurement for the C 20 H 30 O 2 resin acids by isopimaric equivalence is considered semi-quantitative and could be an under estimate for the abietic acid component, the developed method demonstrated clear advantage over time consuming, hazardous, and unstable derivatization procedures used for gas chromatography and capillary electrophoresis. The developed LC/QToF method was successfully transferred to an LC triple quadrupole mass spectrometer for routine high throughput trace level analysis. Real world samples, including sea water and estuary water, demonstrated excellent spike recoveries by this procedure, indicating that the method is well suited to the monitoring of industrially derived resin acids in environmental surface waters. While no interferences were observed during routine sample analysis using myristic-1-13C acid and palmitic-1-13C acid internal standards, these were later substituted by myristic-d 27 and palmitic-d 31 acid in order to improve method robustness for environmental samples where endogenous parent fatty acids could be present. [ABSTRACT FROM AUTHOR]

• A practical statistical application to overcome limitations of traditional techniques. • A three-tiered approach to solve a challenging weathered crude oil case. • A highly automated statistical workflow for increased efficiency and objectivity. • PCA scatterplots to differentiate oils in a highly intuitive visual clustering. Artificially weathered crude oil "spill" samples were matched to unweathered suspect "source" oils through a three-tiered approach as follows: Tier 1 gas chromatography-flame ionization detection (GC/FID), Tier 2 gas chromatography-mass spectrometry (GC/MS) diagnostic ratios, and Tier 3 multivariate statistics. This study served as proof of concept for a promising and new method of crude oil forensics that applies principal component analysis (PCA) and partial least squares discriminant analysis (PLSDA) in tandem with traditional forensic oil fingerprinting tools to confer additional confidence in challenging oil spill cases. In this study, weathering resulted in physical and chemical changes to the spilled oils, thereby decreasing the reliability of GC/FID and GC/MS diagnostic ratios in source attribution. The shortcomings of these traditional methods were overcome by applying multivariate statistical tools that enabled accurate characterization of the crude oil spill samples in an efficient and defensible manner. [ABSTRACT FROM AUTHOR]