Search

This study investigated the effect of a low amount of polyvinyl alcohol (PVA) and steel fiber reinforcement on fly ash-based geopolymer composite long-term deflection and its microstructure. For testing purposes, specimens with different amounts and types of fiber reinforcement as well as plain (reference) were prepared. The long-term deflection test was performed by loading specimens with 40% of the ultimate flexural strength. A microstructure analysis was performed using polished section specimens, and images were acquired at 25-times magnification on a scanning electron microscope. The results of the flexural strength test show that all geopolymer composites with fiber reinforcement have lower flexural strength than plain geopolymer composites. The long-term deflection tests show that the highest deflections exhibit 1% PVA fiber-reinforced specimens. The lowest amount of deflection is for 1% steel fiber-reinforced specimens. Specific creep shows similar results to plain, and 1% steel fiber-reinforced specimens, while 1% PVA and 0.5% PVA/0.5% steel fiber-reinforced specimen exhibits the same properties. The quantitative microanalysis of the polished section further confirms the deflection results. Specimens with 1% PVA fiber reinforcement have significantly higher porosity than all other specimens. They are followed by plain specimens and 1% steel fiber, and 0.5% PVA/0.5 steel fiber-reinforced specimens have almost the same porosity level. [ABSTRACT FROM AUTHOR]

Highlights • A numerical method for design of beams and frames with complex topology is proposed. • The method is based on extended multi-scale finite element method. • This finite element technology is validated and tested using beam and frame structures. • By reducing length of extra window, the displacement continuity increases and stress fields are more accurate. Abstract A numerical method for design of beams and frames with complex topology is proposed. The method is based on extended multi-scale finite element method where beam finite elements are used on coarse scale and continuum elements on fine scale. A procedure for calculation of multi-scale base functions, up-scaling and downscaling techniques is proposed by using a modified version of window method that is used in computational homogenization. Coarse scale finite element is embedded into a frame of a material that is representing surrounding structure in a sense of mechanical properties. Results show that this method can capture displacements, shear deformations and local stress-strain gradients with significantly reduced computational time and memory comparing to full scale continuum model. Moreover, this method includes a special hybrid finite elements for precise modelling of structural joints. Hence, the proposed method has a potential application in large scale 2D and 3D structural analysis of non-standard beams and frames where spatial interaction between structural elements is important. [ABSTRACT FROM AUTHOR]

This study investigates the cyclic load application impact on fly-ash-based geopolymer composites that are reinforced with a low amount of fibre reinforcement. For reinforcement purposes, polyvinyl alcohol and steel fibres are used. For testing purposes, four geopolymer composite mixes were made, three of which had fibre reinforcement. Simultaneously, specimens were tested for shrinkage, static-load-induced creep, and cyclic-load-induced creep. For static and cyclic creep testing, specimens were loaded with 20% of their strength. For cyclic creep testing, load application and release cycles were seven days long. When each cycle was introduced, the load was applied in steps. Necessary load application or unloading lasted for 5 min and consisted of four steps, each 25% of the necessary load. From the long-term static and cyclic creep tests, it was seen that only the plain specimens showed that static creep strains are within cyclic creep strains. For all the other specimens, the static load was higher than the cyclic-load-induced creep amplitude. Also, 1% polyvinyl alcohol fibre-reinforced specimens showed the most elastic characteristics under cyclic load, and 1% steel fibre-reinforced specimens appeared to be the most resistant to the cyclic load introduction. [ABSTRACT FROM AUTHOR]

Global vibration-based methods in the field of structural health monitoring are intended to capture structural stiffness changes of buildings or other civil engineering structures. Natural frequencies of buildings or bridges are commonly used parameters to monitor these stiffness changes. Therefore, it is essential to clarify the limit at which this method is no longer sensitive enough to be useful for structural health monitoring purposes. This paper numerically investigates the effect of structural damage and soil–structure interaction on cellular-type reinforced concrete buildings' natural frequencies. These buildings are a common housing stock of Eastern Europe but are rarely investigated in this context. Comparisons with a reinforced concrete frame and infill structure building are made. Finite element models representing three structural system types of nine-story reinforced concrete buildings were used for the numerical simulations. Furthermore, a five-story finite element model was used for a damage sensitivity comparison. It is established that, for cellular-type structure buildings to detect damage comparable to that investigated in the paper, structural health (fixed base model frequency) should be monitored directly. Then, a statistical significance level for frequency changes of no more than 0.1% should be adopted. Conversely, the rocking frequency is a very sensitive parameter to monitor building base condition changes. These changes are often a cause of the cracking of building elements. [ABSTRACT FROM AUTHOR]