Search

Mixing involves blending raw rubber or masticated rubber with additives using a rubber mixer, which is the most critical process in rubber production. The internal mixer, as the most important mixing equipment, experiences rotor wear during prolonged operation, affecting the gap between the mixer rotor and the chamber wall. This wear reduces mixing effectiveness, weakens filler dispersion, and ultimately impacts rubber performance. In recent years, as research on multi-walled carbon nanotubes (MWCNTs) and nanomaterials has deepened, their broad application prospects have become increasingly apparent. The objective of the present study is to understand and quantify rotor wear in rubber blends during the mixing process as influenced by multi-walled carbon nanotubes. This study found that with the increase in MWCNT content, the proportion of abrasive wear rises, while the proportion of corrosive wear decreases, leading to reduced overall wear. Compared to rubber without MWCNTs, the Payne effect decreased by 6.78%, 9.57%, 13.03%, 20.48%, and 26.06% with the addition of 1 phr, 3 phr, 5 phr, 7 phr, and 9 phr of MWCNTs, respectively. The friction coefficients between the rubber and metal increased by 6.31%, 8.57%, 25.43%, 39.31%, and 47.61%, while the metal wear rate decreased by 9.08%, 10.73%, 13.41%, 17.46%, and 25%. Conversely, the friction coefficients were reduced by 19.39%, 22.42%, 33.94%, 66.06%, and 76.36%. [ABSTRACT FROM AUTHOR]

Studies show that the long-term operation of a rubber mixer results in wear at the end face of the mixer. End face wear increases the gap between the mixing chamber and the end face, resulting in leakage and a reduction in the mixing performance, affecting the final product's quality. Therefore, it is essential to investigate the wear of the metal face during the mixing process. The present study added aramid fibers to a rubber compound using a mechanical blender to obtain a composite material. Then, the influence of the aramid fibers on the metal friction and wear of the end face of the mixer was analyzed. This article introduces the concept of the wear ratio and explores the friction and wear of metals from the perspective of formulation technology for the first time. With the addition of aramid fibers, the proportion of abrasive wear of rubber on metal decreased, and the proportion of corrosive wear increased during the mixing process; however, when the addition of aramid fibers exceeded 3 phr, the balance of abrasive wear of rubber on metal increased and the proportion of corrosive wear decreased. It was found that aramid fibers have the property of friction reduction, which reduces the wear of the rubber blend on the metal. When the amount of aramid fibers added was 3 phr, the amount of abrasion of the rubber compound on the metal was the lowest. [ABSTRACT FROM AUTHOR]

GF/rubber composites have sound insulation characteristics, heat resistance, good corrosion resistance, and high mechanical strength. The compounding machine's long working hours will inevitably wear the metal on the end face of the compounding machine. The wear of the end face metal will increase the gap between the chamber and the end face, which will lead to material leakage, reduce the mixing effect, and eventually affect the performance of GF/rubber composites. To ensure the implementation of GF/rubber composites, it is necessary to study the frictional wear behavior of GF/rubber composites on metals. In this paper, the effect of blending rubber with different amounts of GF on the frictional wear of metal on the end face was analyzed from the perspective of the formulation process, and the ratio of corrosion wear and abrasive wear was calculated for the first time. [ABSTRACT FROM AUTHOR]

Studies show that the dispersion of silica in the mixing process is an important factor affecting the wear of the mixing chamber. As the most important mixing equipment, the long operational life of the internal mixer will cause wear in the rotor and chamber of the internal mixer. This wear increases the gap between the rotor and chamber of the internal mixer, reduces the mixing performance, weakens the dispersion of packing, and adversely affects the quality of the rubber produced. Therefore, it is important to investigate the metal wear in the mixing process. This article examines the effect of the addition of different amounts of silane coupling agents on metal friction and wear during the mixing process. The silane coupling agent has two functions. The first is to make the surface of the silica hydrophobic, enabling it to combine the inorganic matrix of the silica with the organic matrix of the rubber; the second is to inhibit the aggregation of the silica in the rubber. In the present study, we examine (1) the influence of different formulations on the friction and wear of the metal in the mixing chamber from the perspective of formulation technology, and (2) the correlation between corrosion wear and abrasive wear. It is found that a rubber compound with 6 phr of TESPT has the lowest metal wear and that adding more TESPT does not affect the degree of metal wear. As the amount of TESPT increases, the proportion of abrasive wear decreases, while the proportion of corrosive wear increases, reaching a maximum of 20.7%. In our study we found that abrasive wear is the predominant wear mechanism of a rubber compound on metal. In contrast, the corrosive wear caused by high-temperature water vapor still occupies a large proportion of the total wear. Therefore, improving silica dispersion and reducing abrasive wear are extremely important methods to protect the mixing chamber. However, the corrosion of metals by high-temperature water vapor should also be considered when preparing for the mixing process. [ABSTRACT FROM AUTHOR]

Internal mixer is an important mixing equipment. After working for a long time, the end face of the internal mixer will be worn. The abrasion of the end face can increase the gap between the mixing chamber and the end face, and then material leakage occurs, which reduces the mixing effect and affects the performance of rubber compound. Therefore, it is very necessary to study the wear of the end face in the mixing process. As one‐dimensional nanomaterial, carbon nanotubes (CNTs) have a perfect hexagonal structure and many unusual mechanical, electrical and chemical properties. In recent years, with the deepening of the research of CNTs and nanomaterial's, their broad application prospects have also been continuously revealed. This paper analyzes the influence of rubber compounds with different CNTs content on the friction and wear of the end face from the perspective of formulation, and the correlation between corrosive wear and abrasive wear is studied. In the present study, it is found that as CNTs increase, the proportion of abrasive wear increases, the proportion of corrosive wear decreases, and the amount of the metal wear decreases. With the increase of CNTs, the hindering effect of CNTs on SiO2 molecules is strengthened, the degree of silanization reaction is reduced, the output of high‐temperature water vapor is reduced, and the corrosive wear of the metal is reduced. The spatial structure of CNTs is a cylinder with hexagonal plane, and it has extremely high toughness and softness, so it has slight wear on the metal. On the one hand, CNTs hinder the movement of SiO2 molecules. On the other hand, because CNTs have the wrapping effect on SiO2 molecules, some silica aggregates have no direct contact with the metal, CNTs become the medium for silica aggregates to contact with the metal. Therefore, with the increase of CNTs, the proportion of abrasive wear gradually increases, but the total amount of the metal wear gradually decreases. [ABSTRACT FROM AUTHOR]

Internal mixer is one the most commonly used rubber‐mixing equipment, which has been applied for decades. This device can operate continuously for a long time. Accordingly, it is quite probable to have wear of the end face of the mixer. Studies show that the end face wear increases the gap between the mixing chamber and the end face, resulting in material leakage, reducing the mixing effect and ultimately affecting the properties of the compound. Therefore, it is of significant importance to study the friction and wear of the mixing compound to the metal in the mixing process. Considering the superior characteristics of graphene (GE), it is considered a revolutionary material and has been widely applied in numerous applications. In the present study, the influence of the mixing compound with different amounts of GE on the friction and wear of the metal end face was analyzed and the ratio of the corrosion wear to abrasive wear was calculated for the first time. It was found that as the amount of GE increases, the proportion of abrasive wear on the metal increases, the proportion of corrosive wear on the metal decreases, and the metal wear decreases first and then increases. Moreover, the lowest metal wear can be achieved when the amount of GE is 3 phr. [ABSTRACT FROM AUTHOR]

Perhydropolysilazane (PHPS) is an inorganic polymer composed of -(SiH 2 –NH)- repeating structural units. When used as a coating material, it has the advantages of good solubility, simple curing conditions, flexible curing process, and simple preparation method and can significantly save processing time and cost. This paper investigates the frictional behavior of the PHPS-coated metals cured at different temperatures with NR/BR/SBR composites. The effects of different curing temperatures on the PHPS coatings are characterized using infrared absorption spectroscopy. After curing, the asymmetric stretching and oscillating vibration peaks of the Si–O–Si groups are formed, which is attributed to the hydrolysis reaction of Si–N and Si–H and the subsequent cross-linking curing reaction. The denseness of PHPS coatings increases with the increase in curing temperature. When the curing temperature is 400 °C, the cross-linking curing effect of PHPS is the strongest, and the denseness of the PHPS coating is the best. Furtherly, the frictional wear of metal with NR/BR/SBR composites is analyzed from the perspective of the formulation process for the first time, and the ratio of abrasive wear and corrosion wear is calculated qualitatively. It is found that increasing the curing temperature of the PHPS coating can significantly reduce metal wear and improve corrosion resistance, which is attributed to the formation of the ethanol-water molecular film on the surface of the PHPS coating. The ethanol-water molecular film isolates the contact between the PHPS-coated metal and the NR/BR/SBR composite to a certain extent, acting as a lubricant and thus reducing friction. After rubbing the cured PHPS-coated metal with NR/BR/SBR composite, the wear amounts of the cured PHPS-coated metal at 200 °C, 300 °C, and 400 °C are reduced by 49.06%, 66.74%, and 87.33%, respectively, and the corrosion resistance are improved by 51.52%, 63.64%, and 78.79%, respectively. • The friction behaviour of silicone-coated metal and rubber composites cured at different temperatures was investigated. • The metal wear of the coating cured at 300℃ is reduced by 66.74%, and the corrosion resistance is increased by 63.64%. • After curing at 400℃, the metal wear is reduced by 87.33%, and the corrosion resistance is increased by 78.79%. [ABSTRACT FROM AUTHOR]

As an essential rubber mixing equipment in continuous production, an internal mixer should have a long service life while operating at high intensity. Studies show that at these severe operating conditions, end face wear of the internal mixer is inevitable. It is worth noting that the end face is an important part of the closed mixing chamber. The head of the rotor shaft is inserted into the copper ring of the sealing plate, the sealing plate and the mixing chamber are pressed together by bolts. There is a gap between the rotors and the mixing chamber. During the mixing process, the mixed rubber in the mixing chamber is in direct contact with the end face, the end face metal is frictional and abraded. Wear of the end face may result in a gap between the mixing chamber and the end face, leading to material leakage. As the leakage intensifies, the gap between the end face and the mixing chamber further increases, thereby forming negative feedback. This phenomenon not only affects the chemical composition of the rubber but also reduces the mixing efficiency and decreases the performance of the rubber compound. The end surface material is cobalt chromium molybdenum tungsten alloy. The alloy model is Stellite 6B. In the present study, the influence of different amounts of CF on the friction and wear of the end face is analyzed from the chemical composition perspective. Moreover, the ratio of corrosion wear to abrasive wear is calculated. The obtained results show that as the amount of CF in the compound increases, the proportion of the corrosive wear of the compound to the metal increases, while the proportion of abrasive wear decreases. The highest proportion of corrosive wear and the lowest amount of metal wear can be achieved for the CF amount of 9 phr. As the CF content in the composition increases, the ratio of the corrosive wear of the rubber compound to metal decreases, while the proportion of abrasive wear and the total amount of wear to metal increases. • Studies show that at these severe operating conditions, end seal wear of the internal mixer is inevitable. • This study analyzed the effect of different additions of CF on the friction and wear of the end seal. • The highest proportion of corrosive wear and the lowest amount of metal wear can be achieved for the CF amount of 9 phr. [ABSTRACT FROM AUTHOR]

Internal mixer is an important mixing component in industrial applications. Studies show that when a mixer operates for a long time, wear may appear at the end face of the internal mixer. On the other hand, abrasion of the end face increases the gap between the mixing chamber and the end face. Then, leakage occurs, which reduces the mixing effect and affects the rubber performance. Therefore, it is of significant importance to study the wear of the end face during the mixing process. Graphene oxide (GO) and multi-walled carbon nanotubes (MWCNTs) have excellent electrical characteristics and thermal conductivity so that they have been widely used in various fields such as synthesized composite rubbers. GO and MWCNTs are mechanically blended into natural rubber to obtain GO/MWCNTs composite material. In the present study, the influence of the GO/MWCNTs ratio on the friction and wear of the end face of the internal mixer is analyzed. The obtained results show that MWCNTs and GO molecules interact to form a three-dimensional network structure, which has a greater impact on the degree of silica dispersion, silanization reaction, and metal wear. As the GO content increases, the average friction coefficient between rubber and metal, metal roughness, the proportion of abrasive wear, and the amount of metal wear gradually decrease. The lowest values can be achieved when the amount of added GO is set to 3 phr. When the GO in the mixture exceeds 3 phr, the friction coefficient between rubber and metal, and the metal roughness change, thereby affecting the proportion of abrasive wear and increasing the amount of metal wear in the mixing process. In this experiment, the amount of CNT that reduces GO aggregation is 6 phr. On the whole, when the ratio of GO/MWCNTs is 3/6, the synergistic effect of MWCNTs and GO molecules is maximized, the area of the three-dimensional network structure of GO/MWCNTs is the largest, the dispersibility of SiO 2 is the best, and the amount of wear of the composite material on the metal is the lowest. • In the present study, the influence of the GO/MWCNTs ratio on the friction and wear of the end face of the internal mixer is analyzed. • The obtained results show that MWCNTs and GO molecules interact to form a three-dimensional network structure. • It is concluded that the metal wear is minimized when the ratio of GO/MWCNTs in the GO/MWCNTs composite is set to 3/6. [ABSTRACT FROM AUTHOR]

As the basic equipment in the rubber field, the internal mixer is suitable for long-term rubber mixing. For the continuous production of the factory, the wear of the internal mixer is a problem that cannot be ignored. This article mainly studies the wear of the end face of the internal mixer. The end face of the mixer is connected to the mixing chamber. With the increase in mixing time, the end face of the mixer is inevitably worn. The abrasion of the end face of the internal mixer causes the gap between the end face of the internal mixer and the mixing chamber to increase, and the materials in the mixing chamber leak out. This affects the ratio of materials and reduces the mixing effect. And with the increase in material leakage, the abrasion of the end face of the internal mixer is intensified, which eventually leads to a decrease in the compound's performance. BF is a pure natural inorganic non-metallic material. It has good high-temperature resistance, and high compressive strength can be used in various environments and is inexpensive and cost-effective. Based on this, BF is increasingly used in the rubber field. In this paper, the effect of adding different amounts of BF on the friction and wear of the end face of the internal mixer is studied, and the proportions of varying wear forms are distinguished for the first time. The study finds that with the increase of BF in the compound, the proportion of abrasive wear first decreased and then increased, the balance of corrosion wear first increased and then decreased, and the amount of metal wear first decreased and then increased. It is found that the lowest wear of the rubber compound on the metal can be achieved when the amount of BF reaches 10 phr. When the BF amount increases, the corresponding amount of metal wear increases. • With the increase of mixing time, the end face of the mixer is inevitably worn. • This paper studied the effect of different BF additions on the friction and wear of metals. • It is found that the lowest wear of the rubber compound on the metal can be achieved when the amount of BF reaches 10 phr. [ABSTRACT FROM AUTHOR]