Search

A high-speed wireline interfaces, e.g. LVDS (Low Voltage Differential Signaling), are widely used in the aerospace field for powerful computing in artificial satellites and aircraft [19]. This paper describes Bit Error Rate (BER) prediction methodology for wireline data transmission under irradiation environment at the design stage of data transmitter, which is useful in proactively determining if the design circuit meets the BER criteria of the target system. Using a custom-designed LVDS transmitter (TX) to enhance latch-up immunity [42], the relationship between transistor size and BER has been analyzed with focusing on Single Event Effect (SEE) as a cause of the bit error. The measurement was executed under 84Kr17+ exposure of 322.0 MeV at various flux condition from 1 × 103 to 5 × 105 count/cm2/sec using cyclotron facility. For the analysis of the bit error, circuit simulation by SPICE was utilized with expressing the irradiation environment by a current source model. The current source model represents a single event strike into the circuit at drain and substrate junctions in bulk MOSFETs. For the construction of the current source model, a charge collection was simulated at the single particle strike with the creation of 3D Technology CAD (TCAD) models for the MOS devices of bulk transistor process technology. The simulation result of the charge correction was converted to a simple time-domain equation, and the single-event current source model was produced using the equation. The single-event current source was applied to SPICE simulation at bias current related circuits in the LVDS transmitter, then simulation results are carefully verified whether the output data is disturbed enough to cause bit errors on wireline data transmission. By the simulation, sensitive MOSFETs have been specified and a sum of the gate area for these MOSFETs has 29% better correlation than the normal evaluation index (sum of the drain area) by comparison to the actual BER measurement. Through the precise revelation of the sensitive area by SPICE simulation using the current model, it became possible to estimate BER under irradiation environment at the pre-fabrication design stage. [ABSTRACT FROM AUTHOR]

Singular value decomposition (SVD) beamforming is an attractive tool for reducing the energy consumption of data transmissions in wireless sensor networks whose nodes are equipped with multiple antennas. However, this method is often not practical due to two important shortcomings: it requires channel state information at the transmitter and the computation of the SVD of the channel matrix is generally too complex. To deal with these issues, we propose a method for establishing an SVD beamforming link without requiring feedback of actual channel or SVD coefficients to the transmitter. Concretely, our method takes advantage of channel reciprocity and a power iteration algorithm (PIA) for determining the precoding and decoding singular vectors from received preamble sequences. A low-complexity version that performs no iterations is proposed and shown to have a signal-to-noise-ratio (SNR) loss within 1 dB of the bit error rate of SVD beamforming with least squares channel estimates. The low-complexity method significantly outperforms maximum ratio combining diversity and Alamouti coding. We also show that the computational cost of the proposed PIA-based method is less than the one of using the Golub–Reinsch algorithm for obtaining the SVD. The number of computations of the low-complexity version is an order of magnitude smaller than with Golub–Reinsch. This difference grows further with antenna array size. [ABSTRACT FROM AUTHOR]

This paper presents a new on–off keying modulation circuit for a Class-E power transmitter used in high-data-rate wireless links used for powering medical implants. A circuit technique is proposed to keep the current of the RF choke of the power transmitter constant, while the transmitter turns on and off. This allows the transmitter to quickly turn on and off. To prove the feasibility of the proposed circuit, a wireless power and data transfer link based on the proposed circuit was designed and implemented. At a carrier frequency of 2.5 MHz, the measured data rate was 625 kbps, which means that a data-rate-to-carrier-frequency ratio of 25% has been achieved. The power transfer efficiency and the power delivered to the load, with a 2.37-μH transmitter coil and a 1.4-μH receiver coil separated by a 1.0-cm air gap, were measured to be 21% and 80 mW, respectively. The measured bit error rate of the link was less than 10−5. [ABSTRACT FROM AUTHOR]

An un-coded multi-transmitter query scheme is introduced for wireless backscatter communication systems in which M transmitters and N receivers are used for single-tag connectivity (M × 1 × N). The main idea is to harden the wireless communication channel with a tag device for high data rate readings. The proposed method is designed for multipath fading channels in which the backscatter channel is a multiplicative Rayleigh. A coherent transmit query scheme is used to increase the tag-reflected signals and simultaneously alter the fading statistics in the forward path by implementing a receiver feedback. Full-diversity performance and array gain is achieved using the receiver diversity without requiring any tag antenna diversity. Therefore, the tag device remains simple.Mathematical expressions for the probability density function (PDF) of the backscatter channel are presented using closed-form equations. Bit error rate (BER) simulations for the binary phase shift keying (BPSK) modulation are computed numerically. Diversity gain of 10 dB is obtained by using a 2 × 1 × 1 scheme. The results show that the transmit diversity for single-tag usage performs the same as the tag antenna diversity, at the expense of a moderate transmitter complexity. The tag device remains intact as a requirement for the simplicity and size constraints. Also, the system realization becomes more feasible due to the available space on the transmitter side to accomplish the uncorrelated forward channel conditions. The feasibility study is demonstrated using software-defined radio (SDR) implementations. [ABSTRACT FROM AUTHOR]