Search

Borogermanate glasses singly doped with Dy3+ ions were synthesized and then studied using the absorption and luminescence spectra. Spectroscopic changes of Dy3+ ions have been examined for compositional-dependent glasses with various molar ratios GeO2:B2O3. In this work, several spectroscopic parameters of Dy3+ ions were obtained experimentally and compared to the calculated values from the Judd–Ofelt theory. Luminescence spectra measured for borogermanate glasses consist of blue, yellow and red bands, which correspond to 4F9/2 → 6H15/2, 4F9/2 → 6H13/2 and 4F9/2 → 6H11/2 transitions of Dy3+, respectively. Luminescence lifetimes for the 4F9/2 excited state are reduced, whereas the stimulated emission cross-sections for the most intense 4F9/2 → 6H13/2 yellow transition of Dy3+ increase with increasing GeO2 and decreasing B2O3 concentrations in glass-hosts. Quantum efficiency of the 4F9/2 (Dy3+) excited state is nearly independent on molar ratios GeO2:B2O3. Attractive spectroscopic properties related to the 4F9/2 → 6H13/2 transition of Dy3+ ions are found for borogermanate glasses implying their potential utility for yellow laser action and solid-state lighting technology. [ABSTRACT FROM AUTHOR]

Kowalska et al. [[17]] report near-IR luminescence properties of selected rare-Earth ions (Er SP 3+ sp , Pr SP 3+ sp , Ho SP 3+ sp , Tm SP 3+ sp ) in titanate-germanate glasses under excitation of Yb SP 3+ sp . 35683100 17 Kowalska K., Kuwik M., Pisarska J., Pisarski W.A. Near-IR luminescence of rare-earth ions (Er3+, Pr3+, Ho3+, Tm3+) in titanate-germanate glasses under excitation of Yb3+. Rare-Earth ions, as optically active ions, are usually incorporated into the crystalline phases. [Extracted from the article]

This paper deals with broadband near-infrared luminescence properties of lead germanate glass triply doped with Yb3+/Er3+/Tm3+. Samples were excited at 800 nm and 975 nm. Their emission intensities and lifetimes depend significantly on Er3+ and Tm3+ concentrations. For samples excited at 800 nm, broadband emissions corresponding to the overlapped 3H4 → 3F4 (Tm3+) and 4I13/2 → 4I15/2 (Er3+) transitions centered at 1.45 µm and 1.5 µm was identified. Measurements of decay curves confirm reduction of 3H4 (Tm3+), 2F5/2 (Yb3+) and 4I13/2 (Er3+) luminescence lifetimes and the presence of energy-transfer processes. The maximal spectral bandwidth equal to 269 nm for the 3F4 → 3H6 transition of Tm3+ suggests that our glass co-doped with Yb3+/Er3+/Tm3+ is a good candidate for broadband near-infrared emission. The energy transfer from 4I13/2 (Er3+) to 3F4 (Tm3+) and cross-relaxation processes are responsible for the enhancement of broadband luminescence near 1.8 µm attributed to the 3F4 → 3H6 transition of thulium ions in lead germanate glass under excitation of Yb3+ ions at 975 nm. [ABSTRACT FROM AUTHOR]

In this work, spectroscopic properties of europium and erbium ions in heavy metal oxide glasses have been studied. The phonon energy of the glass host was determined based on Eu3+ excitation spectra measurements. Near-IR emission spectra at 1550 nm related to 4I13/2 → 4I15/2 transition of erbium in heavy metal glasses were examined with special regards to luminescence bandwidth and measured lifetime. In particular, correlation between phonon energy and the measured lifetime 4I13/2 (Er3+) was proposed. The luminescence lifetime for the 4I13/2 upper laser state of erbium decreases with increasing phonon energy in glass matrices. Completely different results were obtained glass samples with europium ions, where the 5D0 lifetime increases with increasing phonon energy. Our investigations suggest that the values of measured 5D0 lifetime equal to radiative lifetimes for all heavy metal oxide glasses. [ABSTRACT FROM AUTHOR]

Novel multicomponent titanate-germanate glasses singly doped with transition metal (Cr3+) and rare earth ions (Eu3+) were synthesized and the glass transition temperatures and thermal stability parameters were determined using DSC measurements. X-ray diffraction analysis confirmed fully amorphous nature of the received samples. Their structural and optical properties were compared with germanate glasses without TiO2. Correlation between local structure and optical properties in titanate-germanate glasses is well evidenced by FT-IR, Raman, EPR, and luminescence spectroscopy. In particular, luminescence spectra and their decays are examined for glass samples, where GeO2 was partially substituted by TiO2. [ABSTRACT FROM AUTHOR]

LMA (Large Mode Area) optical fibers are presently under active investigation to explore their potential for generating laser action or broadband emission directly within the optical fiber structure. Additionally, a wide mode profile significantly reduces the power distribution density in the fiber cross-section, minimizing the power density, photodegradation, or thermal damage. Multi-stage deposition in the MCVD-CDT system was used to obtain the structural doping profile of the LMA fiber multi-ring core doped with Tm3+ and Tm3+/Ho3+ layer profiles. The low alumina content (Al2O3: 0.03wt%) results in low refractive index modification. The maximum concentrations of the lanthanide oxides were Tm2O3: 0.18wt % and Ho2O3: 0.15wt%. The double-clad construction of optical fiber with emission spectra in the eye-safe spectral range of (1.55–2.10 µm). The calculated LP01 Mode Field Diameter (MFD) was 69.7 µm (@ 2000 nm, and 1/e of maximum intensity), which confirms LMA fundamental mode guiding conditions. The FWHM and λmax vs. fiber length are presented and analyzed as a luminescence profile modification. The proposed structured optical fiber with a ring core can be used in new broadband optical radiation source designs. [ABSTRACT FROM AUTHOR]

An investigation of fluoroindate glass and fiber co-doped with Yb3+/Er3+ ions as a potential temperature sensor was assessed using the fluorescence intensity ratio (FIR) technique. Analysis of thermally coupled levels (TCLs—2H11/2 and 4S3/2), non-thermally coupled levels (non-TCLs—4F7/2 and 4F9/2), and their combination were examined. Additionally, the luminescent stability of the samples under constant NIR excitation using different density power at three different temperatures was carried out. The obtained values of absolute sensitivity (0.003 K−1—glass, 0.0019 K−1—glass fiber 2H11/2 → 4S3/2 transition) and relative sensitivity (2.05% K−1—glass, 1.64% K−1—glass fiber 4F7/2 → 4F9/2 transition), as well as high repeatability of the signal, indicate that this material could be used in temperature sensing applications. [ABSTRACT FROM AUTHOR]

Nanophosphors are widely used, especially in biological applications in the first and second biological windows. Currently, nanophosphors doped with lanthanide ions (Ln3+) are attracting much attention. However, doping the matrix with lanthanide ions is associated with a narrow luminescence bandwidth. This paper describes the structural and luminescence properties of co-doped LaPO4 nanophosphors, fabricated by the co-precipitation method. X-ray structural analysis, scanning electron microscope measurements with EDS analysis, and luminescence measurements (excitation 395 nm) of LaPO4:Eu3+/Nd3+ and LaPO4:Eu3+/Nd3+/Yb3+ nanophosphors were made and energy transfer between rare-earth ions was investigated. Tests performed confirmed the crystal structure of the produced phosphors and deposition of rare-earth ions in the structure of LaPO4 nanocrystals. In the range of the first biological window (650–950 nm), strong luminescence bands at the wavelengths of 687 nm and 698 nm (5D0 → 7F4:Eu3+) and 867 nm, 873 nm, 889 nm, 896 nm, and 907 nm (4F3/2 → 4I9/2:Nd3+) were observed. At 980 nm, 991 nm, 1033 nm (2F5/2 → 2F7/2:Yb3+) and 1048 nm, 1060 nm, 1073 nm, and 1080 nm (4F3/2 → 4I9/2:Nd3+), strong bands of luminescence were visible in the 950 nm–1100 nm range, demonstrating that energy transfer took place. [ABSTRACT FROM AUTHOR]

Modified barium gallo-germanate glass hosts are still worthy of attention in studying structure–property relationships. In this work, two different series of glass systems based on (60-x)GeO2-xTiO2-30BaO-10Ga2O3 and (60-x)GeO2-xB2O3-30BaO-10Ga2O3 (x = 10, 30, 50 mol%) were synthesized, and their properties were studied using spectroscopic techniques. X-ray diffraction (XRD) patterns revealed that all fabricated glasses were fully amorphous material. The absorption edge shifted toward the longer wavelengths with a gradual substitution of GeO2. The spectroscopic assignments of titanium ions were performed with excitation and emission spectra compared to the additional sample containing an extremely low content of TiO2 (0.005 mol%). On the basis of Raman and FT-IR investigations, it was found that increasing the TiO2 content caused a destructive effect on the GeO4 and GeO6 structural units. The Raman spectra of a sample containing a predominantly TiO2 (50 mol%) proved that the band was located near 650 cm−1, which corresponded to the stretching vibration of Ti-O in TiO6 unit. The deconvoluted IR results showed that the germanate glass network consisted of the coexistence of two BO3 and BO4 structural groups. Based on the experimental investigations, we concluded that the developed materials are a promising candidate for use as novel glass host matrices for doping rare-earth and/or transition metal ions. [ABSTRACT FROM AUTHOR]

In this paper, the effect of the GeO2:TiO2 molar ratio in glass composition on the spectroscopic properties of germanate glasses was systematically investigated. The visible luminescence bands associated with characteristic 1D2 → 3H4 (red), 5S2, 5F4 → 5I8 (green), and 1D2 → 3F4 (blue) transitions of Pr3+, Ho3+, and Tm3+ ions in systems modified by TiO2 were well observed, respectively. It was found that the luminescence intensity of glasses containing Pr3+ and Ho3+ ions increases, whereas, for Tm3+-doped systems, luminescence quenching with increasing content of TiO2 was observed. Based on Commission Internationale de I'Eclairage (CIE) chromaticity coordinates (x, y) analysis, it was demonstrated that the value of chromaticity coordinates for all glasses depends on the GeO2:TiO2 molar ratio. The addition of TiO2 to system compositions doped with Tm3+ ions shifts the (x, y) to the center of the CIE diagram. However, chromaticity coordinates evaluated for glasses containing Pr3+ ions move to a purer red color. Our results confirm that the spectroscopic properties of the studied glasses strongly depend on TiO2 content. Moreover, it can be stated that germanate-based glass systems modified by TiO2 can be used for optoelectronics in RGB technology as red (Pr3+), green (Ho3+), and blue (Tm3+) emitters. [ABSTRACT FROM AUTHOR]

In this work, the series of Dy3+-doped silicate xerogels were synthesized by sol-gel technique and further processed at 350 °C into SiO2-LaF3:Dy3+ nano-glass-ceramic materials. The X-ray diffraction (XRD) measurements, along with the thermal analysis, indicated that heat-treatment triggered the decomposition of La(TFA)3 inside amorphous sol-gel hosts, resulting in the formation of hexagonal LaF3 phase with average crystal size at about ~10 nm. Based on the photoluminescence results, it was proven that the intensities of blue (4F9/2 → 6H15/2), yellow (4F9/2 → 6H13/2), and red (4F9/2 → 6H11/2) emissions, as well as the calculated yellow-to-blue (Y/B) ratios, are dependent on the nature of fabricated materials, and from fixed La3+:Dy3+ molar ratios. For xerogels, the emission was gradually increased, and the τ(4F9/2) lifetimes were elongated to 42.7 ± 0.3 μs (La3+:Dy3+ = 0.82:0.18), however, for the sample with the lowest La3+:Dy3+ molar ratio (0.70:0.30), the concentration quenching was observed. For SiO2-LaF3:Dy3+ nano-glass-ceramics, the concentration quenching effect was more visible than for xerogels and started from the sample with the highest La3+:Dy3+ molar ratio (0.988:0.012), thus the τ(4F9/2) lifetimes became shorter from 1731.5 ± 5.7 up to 119.8 ± 0.4 μs. The optical results suggest, along with an interpretation of XRD data, that Dy3+ ions were partially entered inside LaF3 phase, resulting in the shortening of Dy3+-Dy3+ inter-ionic distances. [ABSTRACT FROM AUTHOR]

In this work, the synthesis and characterization of Li2MgGeO4:Ho3+ ceramics were reported. The X-ray diffraction measurements revealed that the studied ceramics belong to the monoclinic Li2MgGeO4. Luminescence properties were analyzed in the visible spectral range. Green and red emission bands correspondent to the 5F4,5S2→5I8 and 5F5→5I8 transitions of Ho3+ were observed, and their intensities were significantly dependent on activator concentration. Luminescence spectra were also measured under direct excitation of holmium ions or ceramic matrix. Holmium ions were inserted in crystal lattice Li2MgGeO4, giving broad blue emission and characteristic 4f-4f luminescent transitions of rare earths under the selective excitation of the ceramic matrix. The presence of the energy transfer process between the host lattice and Ho3+ ions was suggested. [ABSTRACT FROM AUTHOR]

The effect of BaF2, MgF2, and AlF3 on the structural and luminescent properties of gallo-germanate glass (BGG) doped with erbium ions was investigated. A detailed analysis of infrared and Raman spectra shows that the local environment of erbium ions in the glass was influenced mainly by [GeO]4 and [GeO]6 units. Moreover, the highest number of non-bridging oxygens was found in the network of the BGG glass modified by MgF2. The 27Al MAS NMR spectrum of BGG glass with AlF3 suggests the presence of aluminum in tetra-, penta-, and octahedral coordination geometry. Therefore, the probability of the 4I13/2→4I15/2 transition of Er3+ ions increases in the BGG + MgF2 glass system. On the other hand, the luminescence spectra showed that the fluoride modifiers lead to an enhancement in the emission of each analyzed transition when different excitation sources are employed (808 nm and 980 nm). The analysis of energy transfer mechanisms shows that the fluoride compounds promote the emission intensity in different channels. These results represent a strong base for designing glasses with unique luminescent properties. [ABSTRACT FROM AUTHOR]

Glass-ceramic is semi-novel material with many applications, but it is still problematic in obtaining fibers. This paper aims to develop a new glass-ceramic material that is a compromise between crystallization, thermal stability, and optical properties required for optical fiber technology. This compromise is made possible by an alternative method with a controlled crystallization process and a suitable choice of the chemical composition of the core material. In this way, the annealing process is eliminated, and the core material adopts a glass-ceramic character with high transparency directly in the drawing process. In the experiment, low phonon antimony-germanate-silicate glass (SGS) doped with Eu3+ ions and different concentrations of P2O5 were fabricated. The glass material crystallized during the cooling process under conditions similar to the drawing processes'. Thermal stability (DSC), X-ray photo analysis (XRD), and spectroscopic were measured. Eu3+ ions were used as spectral probes to determine the effect of P2O5 on the asymmetry ratio for the selected transitions (5D0 → 7F1 and 5D0 → 7F2). From the measurements, it was observed that the material produced exhibited amorphous or glass-ceramic properties, strongly dependent on the nucleator concentration. In addition, the conducted study confirmed that europium ions co-form the EuPO4 structure during the cooling process from 730 °C to room temperature. Moreover, the asymmetry ratio was changed from over 4 to under 1. The result obtained confirms that the developed material has properties typical of transparent glass-ceramic while maintaining high thermal stability, which will enable the fabrication of fibers with the glass-ceramic core. [ABSTRACT FROM AUTHOR]

Inorganic glasses co-doped with rare-earth ions have a key potential application value in the field of optical communications. In this paper, we have fabricated and then characterized multicomponent TiO2-modified germanate glasses co-doped with Yb3+/Ln3+ (Ln = Pr, Er, Tm, Ho) with excellent spectroscopic properties. Glass systems were directly excited at 980 nm (the 2F7/2 → 2F5/2 transition of Yb3+). We demonstrated that the introduction of TiO2 is a promising option to significantly enhance the main near-infrared luminescence bands located at the optical telecommunication window at 1.3 μm (Pr3+: 1G4 → 3H5), 1.5 μm (Er3+: 4I13/2 → 4I15/2), 1.8 μm (Tm3+: 3F4 → 3H6) and 2.0 μm (Ho3+: 5I7 → 7I8). Based on the lifetime values, the energy transfer efficiencies (ηET) were estimated. The values of ηET are changed from 31% for Yb3+/Ho3+ glass to nearly 53% for Yb3+/Pr3+ glass. The investigations show that obtained titanate–germanate glass is an interesting type of special glasses integrating luminescence properties and spectroscopic parameters, which may be a promising candidate for application in laser sources emitting radiation and broadband tunable amplifiers operating in the near-infrared range. [ABSTRACT FROM AUTHOR]

The results presented in this communication concern visible and near-IR emission of Pr3+ ions in selected inorganic glasses, i.e., borate-based glass with Ga2O3 and BaO, lead-phosphate glass with Ga2O3, gallo-germanate glass modified by BaO/BaF2, and multicomponent fluoride glass based on InF3. Glasses present several emission bands at blue, reddish orange, and near-infrared spectral ranges, which correspond to 4f–4f electronic transitions of Pr3+. The profiles of emission bands and their relative intensity ratios depend strongly on glass-host. Visible emission of Pr3+ ions is tuned from red/orange for borate-based glass to nearly white light for multicomponent fluoride glass based on InF3. The positions and spectral linewidths for near-infrared luminescence bands at the optical telecommunication window corresponding to the 1G4 → 3H5, 1D2 → 1G4, and 3H4 → 3F3,3F4 transitions of Pr3+ are dependent on glass-host matrices and excitation wavelengths. Low-phonon fluoride glasses based on InF3 and gallo-germanate glasses with BaO/BaF2 are excellent candidates for broadband near-infrared optical amplifiers. Spectroscopic properties of Pr3+-doped glasses are compared and discussed in relation to potential optical applications. [ABSTRACT FROM AUTHOR]

In this paper, some series of lead borate glasses and glass ceramics singly doped with Dy3+ ions were prepared and then studied using spectroscopic techniques. Our research includes mainly studies of the luminescence properties of received materials for white light. The luminescence bands associated with the characteristic 4F9/2→6H15/2 (blue), 4F9/2→6H13/2 (yellow) and 4F9/2→6H11/2 (red) transitions of trivalent dysprosium in lead borate systems are well observed. In particular, the Commission Internationale de I'Eclairage (CIE) chromaticity coordinates (x, y) were calculated in relation to potential applications for white light-emitting diodes (W-LEDs). Their values depend on the relative B2O3/PbO ratios and PbX2 contents (where X = Cl, F, Br) in glass composition. For glass-ceramics, the chromaticity coordinates are changed significantly under different excitation wavelengths. [ABSTRACT FROM AUTHOR]

The effect of oxide modifiers on multiple properties (structural and spectroscopic) of phosphate glasses with molar composition 60P2O5-(10−x)Ga2O3-30MO-xEu2O3 and 60P2O5-(10−y)Ga2O3-30MO-yEr2O3 (where M = Ca, Sr, Ba; x = 0, 0.5; y = 0, 1) were systematically examined and discussed. The local structure of systems was evidenced by the infrared (IR-ATR) and Raman spectroscopic techniques. The spectroscopic behaviors of the studied glass systems were determined based on analysis of recorded spectra (excitation and emission) as well as luminescence decay curves. Intense red and near-infrared emissions (1.5 μm) were observed for samples doped with Eu3+ and Er3+ ions, respectively. It was found that the value of fluorescence intensity ratio R/O related to 5D0→7F2 (red) and 5D0→7F1 (orange) transition of Eu3+ ions depends on the oxide modifiers MO in the glass host. However, no clear influence of glass modifiers on the luminescence linewidth (FWHM) was observed for phosphate systems doped with Er3+ ions. Moreover, the 5D0 and 4I13/2 luminescence lifetimes of Eu3+ and Er3+ ions increase with the increasing ionic radius of M2+ (M = Ca, Sr, Ba) in the host matrix. The obtained results suggest the applicability of the phosphate glasses with oxide modifiers as potential red and near-infrared photoluminescent materials in photonic devices. [ABSTRACT FROM AUTHOR]

In the present work, the Tb3+/Eu3+ co-activated sol-gel glass-ceramic materials (GCs) containing MF3 (M = Y, La) nanocrystals were fabricated during controlled heat-treatment of silicate xerogels at 350 °C. The studies of Tb3+ → Eu3+ energy transfer process (ET) were performed by excitation and emission spectra along with luminescence decay analysis. The co-activated xerogels and GCs exhibit multicolor emission originated from 4fn–4fn optical transitions of Tb3+ (5D4 → 7FJ, J = 6–3) as well as Eu3+ ions (5D0 → 7FJ, J = 0–4). Based on recorded decay curves, it was found that there is a significant prolongation in luminescence lifetimes of the 5D4 (Tb3+) and the 5D0 (Eu3+) levels after the controlled heat-treatment of xerogels. Moreover, for both types of prepared GCs, an increase in ET efficiency was also observed (from ηET ≈ 16% for xerogels up to ηET = 37.3% for SiO2-YF3 GCs and ηET = 60.8% for SiO2-LaF3 GCs). The changes in photoluminescence behavior of rare-earth (RE3+) dopants clearly evidenced their partial segregation inside low-phonon energy fluoride environment. The obtained results suggest that prepared SiO2-MF3:Tb3+, Eu3+ GC materials could be considered for use as optical elements in RGB-lighting optoelectronic devices operating under near-ultraviolet (NUV) excitation. [ABSTRACT FROM AUTHOR]

Technology of active glass-ceramics (GC) is an important part of luminescent materials engineering. The classic method to obtain GC is based on annealing of parent glass in proper temperature and different time periods. Generally, only the bulk materials are investigated as a starting host for further applications. However, the effect of an additional heat-treatment process on emission and structural properties during GC processing is omitted. Here, we focus on the possibility of obtaining transparent glass-ceramic doped with europium ions directly with a melt-quenching method. The influence of phosphate concentration (up to 10 mol %) on the inversion symmetry of local environment of Eu3+ ions in antimony-germanate-silicate (SGS) glass has been investigated. The Stark splitting of luminescence spectra and the local asymmetry ratio estimated by relation of (5D0→7F2)/(5D0→7F1) transitions in fabricated glass confirms higher local symmetry around Eu3+ ions. Based on XRD and SEM/EDX measurements, the EuPO4 nano- and microcrystals with monoclinic geometry were determined. Therefore, in our experiment, we confirmed possibility of one-step approach to fabricate crystalline structures (glass-ceramic) in Eu-doped SGS glass without additional annealing process. [ABSTRACT FROM AUTHOR]

The synthesis and characterization of multicolor light-emitting nanomaterials based on rare earths (RE3+) are of great importance due to their possible use in optoelectronic devices, such as LEDs or displays. In the present work, oxyfluoride glass-ceramics containing BaF2 nanocrystals co-doped with Tb3+, Eu3+ ions were fabricated from amorphous xerogels at 350 °C. The analysis of the thermal behavior of fabricated xerogels was performed using TG/DSC measurements (thermogravimetry (TG), differential scanning calorimetry (DSC)). The crystallization of BaF2 phase at the nanoscale was confirmed by X-ray diffraction (XRD) measurements and transmission electron microscopy (TEM), and the changes in silicate sol–gel host were determined by attenuated total reflectance infrared (ATR-IR) spectroscopy. The luminescent characterization of prepared sol–gel materials was carried out by excitation and emission spectra along with decay analysis from the 5D4 level of Tb3+. As a result, the visible light according to the electronic transitions of Tb3+ (5D4 → 7FJ (J = 6–3)) and Eu3+ (5D0 → 7FJ (J = 0–4)) was recorded. It was also observed that co-doping with Eu3+ caused the shortening in decay times of the 5D4 state from 1.11 ms to 0.88 ms (for xerogels) and from 6.56 ms to 4.06 ms (for glass-ceramics). Thus, based on lifetime values, the Tb3+/Eu3+ energy transfer (ET) efficiencies were estimated to be almost 21% for xerogels and 38% for nano-glass-ceramics. Therefore, such materials could be successfully predisposed for laser technologies, spectral converters, and three-dimensional displays. [ABSTRACT FROM AUTHOR]

This study presented an analysis of the TeO2/GeO2 molar ratio in an oxide glass system. A family of melt-quenched glasses with the range of 0–35 mol% of GeO2 has been characterized by using DSC, Raman, MIR, refractive index, PLE, PL spectra, and time-resolved spectral measurements. The increase in the content of germanium oxide caused an increase in the transition temperature but a decrease in the refractive index. The photoluminescence spectra of europium ions were examined under the excitation of 465 nm, corresponding to 7F0 → 5D2 transition. The PSB (phonon sidebands) analysis was carried out to determine the phonon energy of the glass hosts. It was reported that the red (5D0 → 7F2) to orange (5D0 → 7F1) fluorescence intensity ratio for Eu3+ ions decreased from 4.49 (Te0Ge) to 3.33 (Te15Ge) and showed a constant increase from 4.58 (Te20Ge) to 4.88 (Te35Ge). These optical features were explained in structural studies, especially changes in the coordination of [4]Ge to [6]Ge. The most extended lifetime was reported for the Eu3+ doped glass with the highest content of GeO2. This glass was successfully used for the drawing of optical fiber. [ABSTRACT FROM AUTHOR]

Glasses containing two different network-forming components and doped with optically active ions exhibit interesting properties. In this work, glass systems based on germanium dioxide and boron trioxide singly doped with lanthanides (Eu3+) and transition metals (Cr3+) ions are research subjects. Optical spectroscopy was the major research tool used to record excitation and emission spectra in a wide spectral range for studied systems. The emitted radiation of glasses doped with Cr3+ ions is dominated by broadband luminescence centered at 770 nm and 1050 nm (4T2 → 4A2). Interestingly, the increase of concentration of one of the oxides contributed to the detectable changes of the R-line (2E → 4A2) of Cr3+ ions. Moreover, EPR spectroscopy confirmed the paramagnetic properties of the obtained glasses. The influence of molar ratio GeO2:B2O3 on spectroscopic properties for Eu3+ ions is discussed. The intensity of luminescence bands due to transitions of trivalent europium ions as well as the ratio R/O decrease with the increase of B2O3. On the other hand, the increase in concentration B2O3 influences the increasing tendency of luminescence lifetimes for the 5D0 state of Eu3+ ions. The results will contribute to a better understanding of the role of the glass host and thus the prospects for new optical materials. [ABSTRACT FROM AUTHOR]

An investigation of the structural and luminescent properties of the transparent germanate glass-ceramics co-doped with Ni2+/Er3+ for near-infrared optical fiber applications was presented. Modification of germanate glasses with 10–20 ZnO (mol.%) was focused to propose the additional heat treatment process controlled at 650 °C to obtain transparent glass-ceramics. The formation of 11 nm ZnGa2O4 nanocrystals was confirmed by the X-ray diffraction (XRD) method. It followed the glass network changes analyzed in detail (MIR—Mid Infrared spectroscopy) with an increasing heating time of precursor glass. The broadband 1000–1650 nm luminescence (λexc = 808 nm) was obtained as a result of Ni2+: 3T2(3F) → 3A2(3F) octahedral Ni2+ ions and Er3+: 4I13/2 → 4I15/2 radiative transitions and energy transfer from Ni2+ to Er3+ with the efficiency of 19%. Elaborated glass–nanocrystalline material is a very promising candidate for use as a core of broadband luminescence optical fibers. [ABSTRACT FROM AUTHOR]

Besides high-power light-emitting diodes (LEDs) with dimensions in the range of mm, micro-LEDs (μLEDs) are increasingly gaining interest today, motivated by the future applications of μLEDs in augmented reality displays or for nanometrology and sensor technology. A key aspect of this miniaturization is the influence of the structure size on the electrical and optical properties of μLEDs. Thus, in this article, investigations of the size dependence of the electro-optical properties of μLEDs, with diameters in the range of 20 to 0.65 μm, by current–voltage and electroluminescence measurements are described. The measurements indicated that with decreasing size leakage currents in the forward direction decrease. To take advantage of these benefits, the surface has to be treated properly, as otherwise sidewall damages induced by dry etching will impair the optical properties. A possible countermeasure is surface treatment with a potassium hydroxide based solution that can reduce such defects. [ABSTRACT FROM AUTHOR]

This work reports on the fabrication and analysis of near-infrared and mid-infrared luminescence spectra and their decays in fluoroindate glasses co-doped with Yb3+/Ho3+. The attention has been paid to the analysis of the Yb3+→ Ho3+ energy transfer processed ions in fluoroindate glasses pumped by 976 nm laser diode. The most effective sensitization for 2 μm luminescence has been obtained in glass co-doped with 0.8YbF3/1.6HoF3. Further study in the mid-infrared spectral range (2.85 μm) showed that the maximum emission intensity has been obtained in fluoroindate glass co-doped with 0.1YbF3/1.4HoF3. The obtained efficiency of Yb3+→ Ho3+ energy transfer was calculated to be up to 61% (0.8YbF3/1.6HoF3), which confirms the possibility of obtaining an efficient glass or glass fiber infrared source for a MID-infrared (MID-IR) sensing application. [ABSTRACT FROM AUTHOR]

In this work, the series of Tb3+/Eu3+ co-doped xerogels and derivative glass-ceramics containing CaF2 nanocrystals were prepared and characterized. The in situ formation of fluoride crystals was verified by an X-ray diffraction technique (XRD) and transmission electron microscopy (TEM). The studies of the Tb3+/Eu3+ energy transfer (ET) process were performed based on excitation and emission spectra along with luminescence decay analysis. According to emission spectra recorded under near-ultraviolet (NUV) excitation (351 nm, 7F6 → 5L9 transition of Tb3+), the mutual coexistence of the 5D4 → 7FJ (J = 6–3) (Tb3+) and the 5D0 → 7FJ (J = 0–4) (Eu3+) luminescence bands was clearly observed. The co-doping also resulted in gradual shortening of a lifetime from the 5D4 state of Tb3+ ions, and the ET efficiencies were varied from ηET = 11.9% (Tb3+:Eu3+ = 1:0.5) to ηET = 22.9% (Tb3+:Eu3+ = 1:2) for xerogels, and from ηET = 25.7% (Tb3+:Eu3+ = 1:0.5) up to ηET = 67.4% (Tb3+:Eu3+ = 1:2) for glass-ceramics. Performed decay analysis from the 5D0 (Eu3+) and the 5D4 (Tb3+) state revealed a correlation with the change in Tb3+–Eu3+ and Eu3+–Eu3+ interionic distances resulting from both the variable Tb3+:Eu3+ molar ratio and their partial segregation in CaF2 nanophase. [ABSTRACT FROM AUTHOR]

Highly luminescent europium complexes modified mesoporous silica particles (MSP) were synthesized as an imaging probes for both in-vitro diagnostic and in-vivo cellular tracking agents. Europium β-diketone chelates (4,4,4-trifluoro-l-(2-thienyl)-l,3-butanedione) trioctylphosphine europium (III) (Eu(TTA)3(P(Oct)3)3) were incorporated inside the nanocavities that existed in hierarchical MSP (Eu@MSP). The MSP and Eu@MSP on mouse bone marrow-derived macrophages (BMDMs) did not show any toxic effect. The MSP and Eu@MSP in the BMDMs were found at cytoplasm without any degradation and immunogenicity. However, both pro- and anti-inflammatory cytokines of macrophages were significantly increased when lipopolysaccharide and a high concentration (100 μg/mL) of MSP and Eu@MSP were treated simultaneously. [ABSTRACT FROM AUTHOR]

In this work, we performed a systematic analysis of the impact of selected chemical reagents used in sol-gel synthesis (i.e., N,N-dimethylformamide) and different catalyst agents (i.e., CH3COOH, HNO3) on the formation and luminescence of Eu3+-doped SiO2–LaF3 nano-glass–ceramics. Due to the characteristic nature of intra-configurational electronic transitions of Eu3+ ions within the 4f6 manifold (5D0 → 7FJ, J = 0–4), they are frequently used as a spectral probe. Thus, the changes in the photoluminescence profile of Eu3+ ions could identify the general tendency of rare earth materials to segregate inside low-phonon energy fluoride nanocrystals, which allows us to assess their application potential in optoelectronics. Fabricated sol-gel materials, from sols to gels and xerogels to nano-glass–ceramics, were examined using several experimental techniques: X-ray diffraction (XRD), transmission electron microscopy (TEM), infrared spectroscopy (IR), and luminescence measurements. It was found that the distribution of Eu3+ ions between the amorphous silicate sol-gel host and LaF3 nanocrystals is strictly dependent on the initial composition of the obtained sols, and the lack of N,N-dimethylformamide significantly promotes the segregation of Eu3+ ions inside LaF3 nanocrystals. As a result, we detected long-lived luminescence from the 5D0 excited state equal to 6.21 ms, which predisposes the obtained glass–ceramic material for use as an optical element in reddish-orange emitting devices. [ABSTRACT FROM AUTHOR]

Glass and ceramic materials doped with rare earth (RE) ions have gained wide interest in photonics as active materials for lasers, optical amplifiers, and luminescent sensors. The emission properties of RE-doped glasses depend on their chemical composition, but they can also be tailored by modifying the surrounding active ions. Typically, this is achieved through heat treatment (including continuous-wave and pulsed lasers) after establishing the ordering mechanisms in the particular glass–RE system. Within the known systems, silicate glasses predominate, while much less work relates to materials with lower energy phonons, which allow more efficient radiation sources to be constructed for photonic applications. In the present work, the luminescent and structural properties of germanate glasses modified with phosphate oxide doped with Eu3+ ions were investigated. Europium dopant was used as a "spectroscopic probe" in order to analyze the luminescence spectra, which characterizes the changes in the local site symmetries of Eu3+ ions. Based on the spectroscopic results, a strong influence of P2O5 content was observed on the excitation and luminescence spectra. The luminescence study of the most intense 5D0→7F2 (electric dipole) transition revealed that the increase in the P2O5 content leads to the linewidth reduction (from 15 nm to 10 nm) and the blue shift (~2 nm) of the emission peak. According to the crystal field theory, the introduction of P2O5 into the glass structure changes the splitting number of sublevels of the 5D0→7F1 (magnetic dipole) transition, confirming the higher polymerization of fabricated glass. The slightly different local environment of Eu3+ centers the results in a number of sites and causes inhomogeneous broadening of spectral lines. It was found that the local asymmetry ratio estimated by the relation of (5D0→7F2)/(5D0→7F1) transitions also confirms greater changes in local symmetry around Eu3+ ions. Our results indicate that modification of germanate glass by P2O5 allows control of their structural properties in order to functionalize the emissions for application as luminescent light sources and sensors. [ABSTRACT FROM AUTHOR]

The ErF3-doped oxyfluoride phospho-tellurite glasses in the (40-x) TeO2-10P2O5-45 (BaF2-ZnF2) -5Na2O-xErF3 system (where x = 0.25, 0.50, 0.75, 1.00, and 1.25 mol%) have been prepared by the conventional melt-quenching method. The effect of erbium trifluoride addition on thermal, structure, and spectroscopic properties of oxyfluoride phospho-tellurite precursor glass was studied by differential scanning calorimetry (DSC), Fourier-transform infrared (FTIR), and Raman spectroscopy as well as emission measurements, respectively. The DSC curves were used to investigate characteristic temperatures and thermal stability of the precursor glass doped with varying content of ErF3. FTIR and Raman spectra were introduced to characterize the evolution of structure and phonon energy of the glasses. It was found that the addition of ErF3 up to 1.25 mol% into the chemical composition of phospho-tellurite precursor glass enhanced 2.7 µm emission and upconversion. By controlled heat-treatment process of the host glass doped with the highest content of erbium trifluoride (1.25 mol%), transparent erbium-doped phospho-tellurite glass-ceramic (GC) was obtained. X-ray diffraction analysis confirmed the presence of BaF2 nanocrystals with the average 16 nm diameter in a glass matrix. Moreover, MIR, NIR, and UC emissions of the glass-ceramic were discussed in detail and compared to the spectroscopic properties of the glass doped with 1.25 mol% of ErF3 (the base glass). [ABSTRACT FROM AUTHOR]