Search

This technical note communicates the thermal performance of a modified ten-Ton Refrigerant Direct Expansion (10-TR DX) air conditioning unit into a chiller under actual operating conditions. The modified unit achieved higher COP and cooling capacity compared with conventional DX. The increase in the unit cooling capacity is basically attributed to the enhanced heat transfer coefficient of the Plate-and-Frame Heat Exchanger evaporator. Copyright © 2009 John Wiley & Sons, Ltd. [ABSTRACT FROM AUTHOR]

In this paper, an experimental performance evaluation of a direct expansion ground-coupled heat pump (DX-GCHP) system in heating mode is presented. The DX-GCHP uses R134a as the refrigerant, and consists of three single U-tube copper ground heat exchangers (GHEs) placed in three 30 m vertical boreholes. During the on–off operations from December 25, 2007, to February 6, 2008, the heat pump supplied hot water to fan-coil at around 50.4°C, and its heating capacity was about 6.43 kW. The energy-based heating coefficient of performance (COP) values of the heat pump and the whole system were found to be on average 3.55 and 3.28 at an evaporating temperature of 3.14°C and a condensing temperature of 53.4°C, respectively. The second law efficiency on the DX-GCHP unit basis was around 0.36. The exergetic COP values of the heat pump and the whole system were obtained to be 0.599 and 0.553 (the reference state temperature was set equal to the average outdoor temperature of -1.66°C during the tests), respectively. The authors also discussed some practical points such as the heat extraction rate from the ground, refrigerant charge and two possible new configurations to simultaneously deal with maldistribution and instability of parallel GHE evaporators. This paper may reveal insights that will aid more efficient design and improvement for potential investigators, designers and operators of such DX-GCHP systems. Copyright © 2009 John Wiley & Sons, Ltd. [ABSTRACT FROM AUTHOR]

Hydrocarbons (HCs) are excellent refrigerants in many ways such as energy efficiency, critical point, solubility, transport and heat transfer properties, but they are also flammable, which causes the need for changes in standards, production and product. There are increasing number of scientists and engineers who believe that an alternative solution, which has been overlooked, may be provided by using HCs. The main objective of this study is to perform energy and exergy analyses for a vapor compression refrigeration system with an internal heat exchanger using a HC, isobutene (R600a). For a refrigeration capacity of 1 kW and cold chamber temperature of 0°C, energy and exergy balances are taken into account to determine the performance of the refrigeration system. Energy and exergy fluxes are determined, and irreversibility rates are calculated for every component of the system. It is seen that the compressor has the highest irreversibility rate, and the heat exchanger has the lowest. Also from the result of the analysis, it is found that condenser and evaporator temperatures have strong effects on energetic and exergetic performances of the system such as coefficient of performance (COP), efficiency ratio (τ), exergetic efficiency (ξ) and irreversibility rate. Copyright © 2008 John Wiley & Sons, Ltd. [ABSTRACT FROM AUTHOR]

Recently a diffusion-driven desalination (DDD) process has been described as a method for distilling mineralized water. Extensive studies have already examined the performance of the process using waste heat in water streams. This work focuses on the performance of the diffusion tower (evaporator) using waste heat in air streams. Both experimental and parametric investigations are included. It is observed that the evaporation process is very inefficient when heated air and ambient water are input to the diffusion tower. In contrast, efficient evaporation is achieved when both heated air and heated water are input to the diffusion tower. An industrial application is considered where a waste heat air stream at 82°C is available and a recuperative heat exchanger is used to heat the feed water. It is found that the optimum operating conditions include an air mass flux of 1.5 kg m-2 s-1, an air to feed water mass flow ratio of 10 in the diffusion tower and a fresh water to air mass flow ratio of 2 in the direct contact condenser. At these operating conditions, a fresh water production efficiency of 0.22 and a specific energy consumption of 0.0012 kW h kg-1 can be achieved. The analytical model used to analyze the performance of the DDD process agrees well with the experimental measurements. Copyright © 2008 John Wiley & Sons, Ltd. [ABSTRACT FROM AUTHOR]

This paper presents a computer-based first law and exergy analysis applied to vapour compression refrigeration systems for determining subcooling and superheating effects of environmentally safe new refrigerants. Three refrigerants are considered: R134a, R407c and R410a. It is found that subcooling and superheating temperatures directly influence the system performance as both condenser and evaporator temperatures are affected. The thermodynamic properties of the refrigerants are formulated using artificial neural network (ANN) methodology. Six ANNs were trained to predict various properties of the three refrigerants. The training and validation of the ANNs were performed with good accuracy. The correlation coefficient obtained when unknown data were used to the networks were found to be equal or very near to 1 which is very satisfactory. Additionally, the present methodology proved to be much better than the linear multiple regression analysis. From the analysis of the results it is found that condenser and evaporator temperatures have strong effects on coefficient of performance (COP) and system irreversibility. Also both subcooling and superheating affect the system performance. This effect is similar for R134a and R407c, and different for R410a. [ABSTRACT FROM AUTHOR]

The Refractance Window® evaporator represents a novel concept in the design of evaporation systems for small food processing plants. In this system thermal energy from circulating hot water is transmitted through a plastic sheet to evaporate water from a liquid product flowing concurrently on the top surface of the plastic. The objectives of this study were to investigate the heat transfer characteristics of this evaporator, determine its energy consumption, and capacity at different tilt angles and product flow rates. The system performance was evaluated with tap water, raspberry juice, and blueberry juice and puree as feed. With a direct steam injection heating method, the steam economy ranged from 0.64 to 0.84, while the overall heat transfer coefficient (U) was 666 W m-2 °C-1. Under this condition, the highest evaporation capacity was 27.1 kg h-1 m-2 for blueberry juice and 31.8 kg h-1 m-2 for blueberry puree. The energy consumption was 2492-2719 kJ kg-1 of water evaporated. Installation of a shell and tube heat exchanger with better temperature control minimized incidences of boiling and frequent discharge of condensate. The steam economy, highest evaporation rate and overall heat transfer coefficient increased to 0.99, 36.0 kg h-1 m-2 and 733 W m-2 °C-1, respectively. [ABSTRACT FROM AUTHOR]