Search

• Five elution methods and optimal elution conditions of cyanide tailings were investigated. • Four reagents were screened to promote the elution of cyanide tailings, and the optimal proportion of these four reagents was determined as 5:2:2:1. • The combination of reagent elution and positive pressure filtration for synergistic elution improved the elution efficiency of cyanide. • The combined elution strategy was applied to engineering and achieved desired results. At present, the cyanide gold extraction process is still the main technology for gold production. Generated cyanide tailings containing highly toxic substances exhibit potential environmental risks. These tailings are in urgent need of purification treatment, especially after being classified as hazardous waste. In this study, the impacts of elution methods, operating time, tailings/water ratios, reagent types on the elution rates of cyanide were investigated. Furthermore, the composite elution method developed in this research was extended for engineering. Results showed that the optimum elution conditions were determined to be: stirring elution, tailings/water ratio (M/V ; 1:1) and operating time (10-20 min). Besides, 4 reagents (sodium dodecyl benzene sulfonate, cyclodextrin, sodium silicate and calcium hydroxide) were selected from four categories of 21 reagents for further composite elution. The cyanide elution rate was the highest (90.7%±0.1%) while the molar ratio of these 4 reagents was 5:2:2:1. Moreover, the combination of reagent elution and positive pressure filtration improved the elution efficiency of cyanide (92.6%±0.8%). And the cyanide content in the toxic leaching solution was lower than the standard value (5.0 mg/L). Furthermore, the composite elution method developed in this study was also extended for engineering. The concentration of cyanide in the leachate was < 5.0 mg/L, and was stable during 189 days of detection. Notably, the effluent can be reused directly, or reused after further treatment. The zero discharge of effluents and solid wastes was realized in the processes. The above results provided supports for the engineering treatment of cyanide tailings. [Display omitted] [ABSTRACT FROM AUTHOR]

Cyanide tailings are the major hazardous wastes generated in the production process of the gold industry, which not only contain highly toxic cyanide, but also contain heavy metals with recycling value and other substances suitable for building materials or filling. These tailings are in urgent need of purification treatment and safe utilization. In this study, the impacts of treatment methods, types and combinations of reagents on decyanation effect were researched. Gold in cyanide tailings was recovered by flotation, and flotation tailings were used for filling after identifying the properties of solid waste. Results are as follows: (1) INCO method and 5 reagents (sodium sulfite, sodium persulfate, copper sulfate, ferrous sulfate and zinc sulfate) were selected for synergistic decyanation treatment, and cyanide concents in slurry and leaching solution were decreased to the minimum. (2) The gold recovery rate of the tailings through flotation was increased by 27.8% than without detoxification. (3) Flotation tailings were identified as general industrial solid wastes by leaching toxicity and toxic substance content analysis. (4) As filling aggregate, under the conditions of slurry concentration of 63% and cement-sand ratio of 1:6, the strength filling body of flotation tailings reached 1.32 Mpa after 28 days of maintenance. (5) This process and combined reagents were applied to engineering. The cyanide content in the leaching solution and the flotation recovery rate of gold were kept below 0.2 mg/L and above 60% respectively, and the strength of the filling body was stable to meet the requirements of underground filling. [Display omitted] • Different decyanation methods and reagents of cyanide tailings were researched. • Five reagents were screened for decyanation and their interaction mechanism was expounded. • Gold was extracted by flotation after detoxification and the gold recovery rate was much higher than that of non-detoxification. • Flotation tailings were identified as general industrial solid wastes for filling, and filling parameters were explored. • Efficient detoxification and full resource utilization of cyanide tailings were realized and applied to industry. [ABSTRACT FROM AUTHOR]

Cyanide tailings are the bulk solid waste generated by the production processes of gold mines. Since the highly toxicity of cyanide affects its disposal and comprehensive utilization, a decyanation treatment is needed. However, wide-ranging industrial uses of the current decyanation methods are restricted due to the treatment effects and costs. Based on the natural degradation method, the cyanide treatment effect was enhanced by raising the treatment temperature, increasing the ultraviolet (UV) irradiation and turning the pile periodically. Using the Arrhenius equation, the activation energies of the cyanide hydrolysis reactions were calculated as 52.22 kJ/mol and 34.59 kJ/mol for heating alone and for heating combined with UV irradiation, respectively. At 60 ℃, the cyanide tailings reached the discharge standard (leachate, total cyanide (CNt)< 5 mg/L) after 8 h of treatment. Moreover, after adding UV irradiation (with an intensity of 120 μW/cm2) and a hydrogen peroxide spray (spraying intensity, 2 mL/kg) to the above conditions and shortening the treatment time to 7 h, the cyanide tailings reached the standard for use in building materials (leachate, CN t <0.5 mg/L). Based on these results, UV irradiation, ventilation, spraying and pile-turning were integrated into the solar drying room to form an enhanced natural degradation system, which was applied in the semi-industrial scale treatment of the cyanide tailings. The results showed that the cyanide tailings consistently met the standards for discharge and use in building materials, successfully verified the conditions and effects of the laboratory treatment, and reduced the treatment cost by more than 50 %. [Display omitted] • Cyanide was mainly distributed in the liquid of the tailings and was removed by volatilization and hydrolysis. • The effects of temperature, UV intensity, turning and reagent spraying on cyanide removal were investigated. • The equation and activation energy of cyanide hydrolysis under heating and UV irradiation were analyzed. • Two methods were designed to meet the different standard requirements for treating cyanide tailings. • Designed an enhanced natural degradation system and completed semi-industrial validation tests. [ABSTRACT FROM AUTHOR]