Search

The development of new materials is currently focused on replacing fossil-based plastics with sustainable materials. Obtaining new bioplastics that are biodegradable and of the greenest possible origin could be a great alternative for the future. However, there are some limitations—such as price, physical properties, and mechanical properties—of these bioplastics. In this sense, the present work aims to explore the potential of lignin present in black liquor from paper pulp production as the main component of a new plastic matrix. For this purpose, we have studied the simple recovery of this lignin using acid precipitation, its thermoplastification with glycerin as a plasticizing agent, the production of blends with poly(caprolactone) (PCL), and finally the development of biocomposite materials reinforcing the blend of thermoplastic lignin and PCL with stone groundwood fibers (SGW). The results obtained show that thermoplastic lignin alone cannot be used as a bioplastic. However, its combination with PCL provided a tensile strength of, e.g., 5.24 MPa in the case of a 50 wt.% blend. In addition, when studying the properties of the composite materials, it was found that the tensile strength of a blend with 20 wt.% PCL increased from 1.7 to 11.2 MPa with 40 wt.% SGW. Finally, it was proven that through these biocomposites it is possible to obtain a correct fiber–blend interface. [ABSTRACT FROM AUTHOR]

In engineering applications, natural fiber composites must comply with fire requirements including the use of flame retardant. Furthermore, biocomposites are known to be water sensitive. Whether flame retardants affect the water sensitivity and whether water absorption affects the fire behavior and the mechanical performance of biocomposites are the two main topics addressed in this work. In this study, a flax fiber/epoxy composite flame retardant with 9,10-dihydro-9-oxa-10-phosphaphenanthrene-10-oxide (DOPO) or aluminum diethyl phosphinate (AlPi) was aged in humid atmosphere or by immersion in water. Water absorption kinetics revealed that DOPO induces an increase in equilibrium water content by approximately a factor of 2 due to its intrinsic hygroscopicity and/or its plasticizing effect on the epoxy matrix. In contrast, AlPi does not significantly change the water sensitivity of the biocomposite. Mechanical testing highlighted that, whatever the FR, the evolution of mechanical properties with ageing is governed by the moisture content. The drop of elastic modulus was attributed to a decrease in fiber rigidity due to plasticization, while the increase in tensile strength was assigned to an increase in fiber/matrix friction due to fiber swelling. As regards flame retardancy, only the highest water contents modified the fire behavior. For the AlPi containing biocomposite, the water release resulted in an increase by 50% of the time to ignition, while for the DOPO flame retardant biocomposite the water release was mainly postponed after ignition. [ABSTRACT FROM AUTHOR]

Mechanical properties of Roselle fiber reinforced vinyl ester biocomposite were studied based on the fiber content and length in the present communication. Usually, natural fiber reinforced polymer composites depend on some aspects such as fiber content, fiber length and orientation, the fiber-matrix adhesion. Composite plates were prepared by a simple hand lay-up technique for two different fiber lengths (3 and 13 mm) and five different fiber content (10, 20, 30, 40 and 50 wt%). Composite specimens were tested according to ASTM and ISO standards and their results were recorded. Experimental results showed that mechanical properties such as tensile, flexural and impact, increases with increase of fiber content up to 40 wt% after which it is decreases at both the fiber length. However, modulus values were increased linearly with fiber content of 10 to 50 wt%. Composites with the fiber length of 13 mm show the high level of mechanical properties compared to composites with the fiber length of 3 mm at all combinations of fiber contents. It is observed that the optimal fiber content is 40 wt%, which can be used to obtain the maximum property level in the Roselle fiber reinforced vinyl ester composites. [ABSTRACT FROM AUTHOR]

Low-porosity materials based on hot-pressed wood fibers or nanocellulose fibrils (no polymer matrix) represent a new concept for eco-friendly materials with interesting mechanical properties. For the replacement of fossil-based materials, physical properties of wood fiber materials need to be improved. In addition, the carbon footprint and cumulative energy required to produce the material also needs to be reduced compared with fossil-based composites, e.g., glass fiber composites. Lignin-containing fibers and nanofibers are of high yield and special interest for development of more sustainable materials technologies. The present mini-review provides a short analysis of the potential. Different extraction routes of lignin-containing wood fibers are discussed, different processing methods, and the properties of resulting fiber materials. Comparisons are made with analogous lignin-containing nanofiber materials, where mechanical properties and eco-indicators are emphasized. Higher lignin content may promote eco-friendly attributes and improve interfiber or interfibril bonding in fiber materials, for improved mechanical performance. [ABSTRACT FROM AUTHOR]

Recycled polylactic acid (PLAr) was reinforced with treated nanocellulosic hemp fibers for biocomposite fabrication. Cellulosic fibers were extracted from hemp fibers chemically and treated enzymatically. Treated nanocellulosic fibers (NCF) were analyzed by Fourier-transform infrared spectroscopy, X-ray diffraction, and scanning electron microscopy. Biocomposite fabrication was done with PLAr and three concentrations of treated NCF (0.1%, 0.25%, and 1% (v/v)) and then studied for thermal stability and mechanical properties. Increased thermal stability was observed with increasing NCF concentrations. The highest value for Young's modulus was for PLAr + 0.25% (v/v) NCF (250.28 ± 5.47 MPa), which was significantly increased compared to PLAr (p = 0.022). There was a significant decrease in the tensile stress at break point for PLAr + 0.25% (v/v) NCF and PLAr + 1% (v/v) NCF as compared to control (p = 0.006 and 0.002, respectively). No significant difference was observed between treatments for tensile stress at yield. [ABSTRACT FROM AUTHOR]