Search

Clay–sand mixtures are deposited worldwide, such as naturally sedimentary soils and dredged clays in human activities. These mixtures usually have a fine fraction above the transitional fine content, and the compressibility is dominated by clay matrix and affected by sand fraction. In this paper, an explicit equivalent compression curve is proposed for clay–sand mixtures. This is done by directly incorporating the equivalent void ratio into the intrinsic compression model of the clay matrix. The roles of initial and evolving soil structure developed during the compression process are described by a structural variable, which can be directly computed from the experimental data. Experimental data compiled from various literature are used for evaluating the accuracy of the suggested model. They indicate that the proposed relationship of stress versus equivalent void ratio is simple yet effective to evaluate the compressibility of clay–sand mixtures with a wide spectrum of sand fraction. The model is also practically useful for estimating the compressibility of other gap-graded soils, such as clay–gravel mixtures. The proposed stress versus equivalent void-ratio equation is an elementary function and can be readily implemented into general elastoplastic models. [ABSTRACT FROM AUTHOR]

To estimate the cyclic shear-induced ground settlement of clay layers, cyclic simple shear tests were carried out on three normally consolidated clays with different plasticity. The pore water pressure accumulation during cyclic shear and the settlement at the postcyclic recompression stage were measured in tests with unidirectional and two-directional shearing, with different phase shifts between the shear strains applied in the two orthogonal directions and a wide range of shear strain amplitudes. All tests were performed with 200 cycles. In conclusion, firstly, the discrepancies of the pore water pressure accumulation and postcyclic settlement between unidirectional and two-directional cyclic shear were quantified, and the effects of cyclic shear direction on these properties were then described by the total length of strain path. Secondly, a method for estimating the cyclic shear-induced pore water pressure accumulation and postcyclic settlement of clayey soils with different plasticities was then developed considering the effect of cyclic shear direction. [ABSTRACT FROM AUTHOR]

Theoretical curves for different values of HT ht , 0.6, 0.8, and 1.0 are superimposed on the graph and can be seen to encapsulate the data. Yet, even without these separate curves, Wroth ([14]) noted that the parameter HT ht would track well with I ' i alone according to CSSM, and recommended the approximation HT ht (5) Graph: Fig. [Extracted from the article]

The stress-dilatancy relationship is a key point to capture the evolution of both strains and excess pore pressure during an undrained creep of natural soft clay. This paper focuses on investigating the stress dilatancy of natural soft clay during an undrained creep. Undrained triaxial creep tests are performed on K0-consolidated and isotropically consolidated samples of a typical Chinese soft marine clay with different stress levels. A unique stress-dilatancy curve is obtained from all test results. Several typical stress-dilatancy relations for soils are discussed, comparing them with experimental results. A common modification method for the stress dilatancy of sand is adopted and discussed for clay. All comparisons demonstrate that modified dilatancy equations can describe the stress-dilatancy relationship during an undrained creep. The modified dilatancy equation with the inclination of a potential surface seems to better describe the whole trend, and is suitable for natural soft clay. [ABSTRACT FROM AUTHOR]

Full-scale testing can be an integral component of quality control/quality assurance for projects involving construction of deep foundations. Rapid load tests are being used in the deep foundation industry as a method for assessing the axial static behavior of deep foundations. Since rapid load tests involve dynamics, inertial and damping forces must be considered in analyzing measured pile response to estimate the static pile response. The unloading point method (UPM) is typically used for this purpose. Generally considered a consequence of load rate effects in clays, results from the UPM must be further modified by a reduction factor to obtain a reasonable estimate of the static pile response. A reduction factor of 0.65 applied to the UPM for clay soil sites has been recommended by others. However, a review and analysis of readily available literature reporting static and rapid pile load test results at sites predominantly consisting of clay soils indicate that an average reduction factor of 0.47 is more appropriate. Rapid load testing should be used judiciously. When using the UPM to estimate static pile capacity from rapid load tests in clay, static load tests should be performed to validate the reduction factor used to interpret rapid load tests. [ABSTRACT FROM AUTHOR]

The laboratory and field test data on the response of piles under the combined action of vertical and lateral loads is rather limited. The current practice for design of piles is to consider the vertical and lateral loads independent of each other. This paper presents some results from three-dimensional finite-element analyses that show the significant influence of vertical loads on a pile’s lateral response. The analyses were performed in both homogeneous clayey soils and homogeneous sandy soils. The results have shown that the influence of vertical loads on the lateral response of piles is to significantly increase the capacity in sandy soils and marginally decrease the capacity in clayey soils. In general, it was found that the effect of vertical loads in sandy soils is significant even for long piles, which are as long as 30 times the pile width, while in the case of clayey soils, the effect is not significant for piles beyond a length of 15 times the width of the pile. The design bending moments in the laterally loaded piles were also found to be dependent on the level of vertical load on the piles. [ABSTRACT FROM AUTHOR]

The conventional design of a piled foundation is based on a bearing capacity approach, and neglects the contribution of the raft. As a consequence, piled foundations are usually designed by overconservative criteria. With respect to the conventional approach, a more rational and economical solution could be obtained by accounting for the contribution of the raft toward the overall bearing capacity, but this potential is not exploited due to the lack of theoretical and experimental research on the behavior of piled rafts at failure. Based on both experimental evidence and three-dimensional finite element analyses, a simple criterion is proposed to evaluate the ultimate vertical load of a piled raft as a function of its component capacities, which can be simply evaluated by the conventional bearing capacity theories. The results presented in the paper thus provide a guide to assess the safety factor of a vertically loaded piled raft. [ABSTRACT FROM AUTHOR]