Search

Due to their reported fast decay times, Cs 2 ZnCl 4 and Cs 3 ZnCl 5 are promising candidates for detection of gamma rays and X-rays in high count rate and fast timing applications. In this work, we show that single crystals with better optical quality than previously demonstrated – and larger in size – can be grown via the vertical Bridgman method. Highly transparent Ø7 mm crystals of undoped Cs 2 ZnCl 4 and Cs 3 ZnCl 5 are grown and measured to have light yields surpassing those previously reported, achieving 1980 ± 100 ph/MeV and 1460 ± 70 ph/MeV at 662 keV – a 55% and 232% improvement, respectively. We observe single-component scintillation decay times for both Cs 2 ZnCl 4 (1.66 ns) and Cs 3 ZnCl 5 (0.82 ns) and radioluminescence emission with maximum intensity at ∼290 nm. Scalability of these materials is also evaluated based on growth of Ø22 mm crystals. Minimal cracking is observed, and the fast decay times are maintained at this size. Coincidence time resolution of 3 × 3 × 5 mm3 and 7 × 7 × 10 mm3 pixels cut from Ø22 mm Cs 2 ZnCl 4 are measured to be 148 ± 1 ps FWHM and 175 ± 1 ps FWHM, respectively. The improved performance and ability to be fabricated in large sizes now place Cs 2 ZnCl 4 and Cs 3 ZnCl 5 on the map as potential contenders for radiation detection applications where BaF 2 – the most commonly used ultrafast inorganic scintillator – is typically considered. • Single crystals of Cs 2 ZnCl 4 and Cs 3 ZnCl 5 were grown by the vertical Bridgman method. • Cs 2 ZnCl 4 had a scintillation decay time of 1.66 ns and light yield of 1980 ph/MeV at 662 keV. • Cs 3 ZnCl 5 had a scintillation decay time of 0.82 ns and light yield of 1460 ph/MeV at 662 keV. • The coincidence time resolution of Cs 2 ZnCl 4 was measured to be as good as 136 ± 2 ps FWHM. [ABSTRACT FROM AUTHOR]

The paper describes the effect of high effective atomic number (Z eff) materials loading in polystyrene based thin-film Plastic Scintillators (PS). Thin plastic scintillator sheets have been loaded with high Z materials such as BaFBr:Eu, Gd 2 O 2 S:Tb, Gd 2 O 3 , BaF 2 , CeO 2 and Bi 2 O 3. Polystyrene based PS sheets of 250 ± 50 μ m thickness have been prepared by dissolving predetermined quantities of polystyrene, 2,5-Diphenyloxazole (PPO) and 1,4-bis(5-phenyl-2-oxazolyl) benzene (POPOP) in the p-xylene solvent. High Z eff material powders of 23 μ m size are mixed in the plastic scintillator solution and coated over the cellulose acetate-based transparency sheets. The dried films are peeled off, and their photoluminescence, radioluminescence, pulse height spectrum and response to alpha, beta, gamma and neutron radiations are studied by adopting suitable methods. The high Z eff materials for loading in PS are selected based on their physical properties like refractive index, bandgap, Z eff , Photoluminescence (PL) properties. While the composite scintillator loaded with 14.3 wt% of BaFBr:Eu2+ showed significant increase compare to other high Z materials. The loading concentration has been optimized as 14.3 wt% from the BaFBr:Eu2+ studies. Most of the composite scintillators showed improvement in radioluminescence and pulse height spectra for different radiations. • Polystyrene based thin plastic scintillator have been prepared by solvent-based fabrication method. • Thin composite plastic scintillator are studied with high Z eff material loading. • High Z eff material loaded composite scintillators showed enhanced response to radiation. • BaFBr:Eu loaded composite PS has shown the best promising result. [ABSTRACT FROM AUTHOR]