Search

Excessive copper (Cu2+) causes adverse effects on human health and the ecological environment. Traditional methods for detecting Cu2+ have drawbacks such as high detection costs, complex operating conditions, and being time consuming. Therefore, there is an urgent need to develop simple detection methods to better meet specific health and environment quality needs. In this work, a paper-based fluorescence sensor was prepared (herein referred to as the as-prepared method) by immersing filter paper in aqueous polyethyleneimine (PEI) solution, and its potential use in Cu2+ detection was investigated. The results showed that the as-prepared paper samples, with fluorescence properties obtained by aggregation-induced luminescence of PEI, have selective recognition of Cu2+ based on the internal filtration effect, and the lowest detection limit is 0.03 μM. In addition, the relative error of this method is in the range of 1.80~2.23%, which is relatively comparable to the national standard method (0.63~630 μM), demonstrating high accuracy. Therefore, paper-based sensors with a simple preparation method have potential applications in the detection of Cu2+ in water. [ABSTRACT FROM AUTHOR]

In this research work, a coated paper was prepared with poly (butylene adipate-co-terephthalate) (PBAT) film to explore its use in eco-friendly food packaging. The paper was coated with PBAT film for packaging using hot pressing, a production method currently employed in the packaging industry. The coated papers were evaluated for their structural, mechanical, thermal, and barrier properties. The structural morphology and chemical analysis of the coated paper confirmed the consistent formation of PBAT bi-layered on paper surfaces. Surface coating with PBAT film increased the water resistance of the paper samples, as demonstrated by tests of barrier characteristics, including the water vapor transmission rate (WVTR), oxygen transmission rate (OTR), and water contact angle (WCA) of water drops. The transmission rate of the clean paper was 2010.40 cc m−2 per 24 h for OTR and 110.24 g m−2 per 24 h for WVTR. If the PBAT-film was coated, the value decreased to 91.79 g m−2 per 24 h and 992.86 cc m−2 per 24 h. The hydrophobic nature of PBAT, confirmed by WCA measurements, contributed to the enhanced water resistance of PBAT-coated paper. This result presents an improved PBAT-coated paper material, eliminating the need for adhesives and allowing for the fabrication of bi-layered packaging. [ABSTRACT FROM AUTHOR]

At the beginning of the 20th century, the eclectic artist Mariano Fortuny y Madrazo patented two innovative methods for polychrome printing on fabrics and textiles, giving life to Fortuny fabric production in Venice. The first patent was related to colour application, while the second to a special machine that allows continuous printing using cylindrical rollers. Despite the descriptions, the methodology and materials used remain a secret. In collaboration with the Fortuny Museum in Venice, this research aimed at studying and identifying the different steps of Fortuny printing methodologies. Printing matrices, fabrics and raw materials found in the artist's studio were analysed in a multi-analytical campaign through digital microscopy, X-ray fluorescence (XRF), Fourier-transform infrared spectroscopy in attenuated total reflectance (FTIR-ATR), μ-Raman spectroscopy and gas chromatography–mass spectrometry (GC–MS). Three main pigments were identified in paper samples: ivory black, a copper-based pigment, and a carbon black pigment with ultramarine for blues. The pigments were bound with linseed oil and colophony in varying proportions. Polychrome silk fabrics were dyed with a base colour, and then the coloured patterns were superimposed by continuous printing. Prussian blue was identified as one of the textile inks. Results provided a better understanding of printing methodology. [ABSTRACT FROM AUTHOR]

The coefficient of friction for different contacting materials against skin is mainly influenced by the nature of the materials (synthetic and natural fabrics), mechanical contact parameters (interfacial pressure and sliding velocities), and physiological skin conditions (ambient humidity and skin moisture content). In the present research work, seven different types of papers used in everyday life were analyzed. The physical properties of these materials were determined through tensile tests and friction tests. By comparing mechanical properties with coefficient of friction, it was possible to conclude that the coefficient of friction is strongly correlated with the mechanical properties. [ABSTRACT FROM AUTHOR]

Beeswax is a bio-sourced, renewable, and even edible material that stands as a convincing option to provide paper-based food packaging with moisture resistance. Nonetheless, the difficulty of dispersing it in water limits its applicability. This work uses oxidized, negatively charged cellulose nanofibers along with glycerol to stabilize beeswax-in-water emulsions above the melting point of the wax. The synergistic effects of nanocellulose and glycerol granted the stability of the dispersion even when it cooled down, but only if the concentration of nanofibers was high enough. This required concentration (0.6–0.9 wt%) depended on the degree of oxidation of the cellulose nanofibers. Rheological hindrance was essential to prevent the buoyancy of beeswax particles, while the presence of glycerol prevented excessive aggregation. The mixtures had yield stress and showed pseudoplastic behavior at a high enough shear rate, with their apparent viscosity being positively influenced by the surface charge density of the nanofibers. When applied to packaging paper, the nanocellulose-stabilized beeswax suspensions not only enhanced its barrier properties towards liquid water (reaching a contact angle of 96°) and water vapor (<100 g m−2 d−1), but also to grease (Kit rating: 5) and airflow (>1400 Gurley s). While falling short of polyethylene-coated paper, this overall improvement, attained using only one layer of a biobased coating suspension, should be understood as a step towards replacing synthetic waxes and plastic laminates. [ABSTRACT FROM AUTHOR]

This article presents results on the use of a new material as a solidifying agent and/or color-fixing agent. A special polysaccharide material extracted from the prickly pear cactus (Opuntia ficus indica) was tested on historical materials and modern papers. An old book from the 18th century was chosen as historical material. From the mentioned book 42 pages were taken, on which a conservation and restoration pretreatment was performed before applying the polysaccharide material: sampling, fiber analysis, dry cleaning, ink solubility, pH test, thickness measurement and wet cleaning. The paper sheets provided for the test were divided into 4 groups, 3 of which were treated with gel and one left untreated as a reference. The division into groups is not only due to the different method of application, but also due to the process of gel extraction. The effect of the treatment was analyzed using FTIR-ATR. To test the mucilage as color-fixing agent 2 samples were prepared using watercolor papers colored with 6 different watercolors applied to 2.5 cm2 samples for each color in two rows of different intensity. One of the 2 samples was treated with gel, but both were immersed for 3 times in a water-ethanol solution for approximately 20 min as is standard practice in conservation and restoration. After washing, both specimens were subjected to colorimetric analysis to assess their differences. The results provided satisfactory evidence for the protection of paints sensitive to aqueous treatments and suggest the use of mucilage as a new material in cleaning method for water-soluble media. [ABSTRACT FROM AUTHOR]

The present study reports on the development by thermoforming of highly sustainable trays based on a bilayer structure composed of paper substrate and a film made of a blend of partially bio-based poly(butylene succinate) (PBS) and poly(butylene succinate-co-adipate) (PBSA). The incorporation of the renewable succinic acid derived biopolyester blend film slightly improved the thermal resistance and tensile strength of paper, whereas its flexural ductility and puncture resistance were notably enhanced. Furthermore, in terms of barrier properties, the incorporation of this biopolymer blend film reduced the water and aroma vapor permeances of paper by two orders of magnitude, while it endowed the paper structure with intermediate oxygen barrier properties. The resultant thermoformed bilayer trays were, thereafter, originally applied to preserve non-thermally treated Italian artisanal fresh pasta, "fusilli calabresi" type, which was stored under refrigeration conditions for 3 weeks. Shelf-life evaluation showed that the application of the PBS–PBSA film on the paper substrate delayed color changes and mold growth for 1 week, as well as reduced drying of fresh pasta, resulting in acceptable physicochemical quality parameters within 9 days of storage. Lastly, overall migration studies performed with two food simulants demonstrated that the newly developed paper/PBS–PBSA trays are safe since these successfully comply with current legislation on plastic materials and articles intended to come into contact with food. [ABSTRACT FROM AUTHOR]

The identification of sustainable materials as an alternative to plastic is fundamental for the protection of the environment and for the safeguard of marine ecosystems. The replacement of plastic with organic materials for fish storage might affect its shelf-life due to the high concentration of oxidizable fatty acids in fish flesh. This study investigated the effectiveness of two organic packaging materials, namely coconut fiber (Coc) and paper (Pap), as alternatives to the conventionally used polystyrene (Pol), on the shelf-life, hygienic parameters, and quality traits of anchovies refrigerated for one (T0), three (T1), or seven (T2) days. The hygienic quality of anchovies packaged in the organic Pap and Coc boxes was better than the traditional Pol, probably due to the higher porosity of the packaging, which allows a higher bacterial proliferation. Results of the T-BARS test showed a lower (p < 0.05) malondialdehyde concentration in fillets from the Pap group, which increased (p < 0.05) from the first to the seventh day of storage. The polyunsaturated fatty acids concentration did not differ between groups, but it decreased (p < 0.05) from T0 to T2. Coconut fiber and paper are worthy of further investigation since these packaging materials did not affect the shelf-life and fatty acid profile of anchovies during storage. [ABSTRACT FROM AUTHOR]

The aim of this study was to develop bio-based adhesives that can be used for various packaging papers. In addition to commercial paper samples, papers produced from harmful plant species in Europe, such as Japanese Knotweed and Canadian Goldenrod, were used. In this research, methods were developed to produce bio-based adhesive solutions in combinations of tannic acid, chitosan, and shellac. The results showed that the viscosity and adhesive strength of the adhesives were best in solutions with added tannic acid and shellac. The tensile strength with adhesives of tannic acid and chitosan was 30% better than with commercial adhesives and 23% for combinations of shellac and chitosan. For paper from Japanese Knotweed and Canadian Goldenrod, the most durable adhesive was pure shellac. Because the surface morphology of the invasive plant papers was more open and had numerous pores compared to the commercial papers, the adhesives penetrated the paper structure and filled the voids. There was less adhesive on the surface and the commercial papers achieved better adhesive properties. As expected, the bio-based adhesives also showed an increase in peel strength and exhibited favorable thermal stability. In summary, these physical properties support the use of bio-based adhesives use in different packaging applications. [ABSTRACT FROM AUTHOR]

(1) Background: Many drugs possess poor bioavailability, and many strategies are available to overcome this issue. In this study, smartFilm technology, i.e., a porous cellulose matrix (paper), in which the active compound can be loaded onto in an amorphous state was utilised for oral administration to improve the solubility and bioactivity of a poorly soluble BSC class IV antibiotic. (2) Methods: Norfloxacin was used as the model drug and loaded into commercially available paper. The resulting norfloxacin-loaded smartFilms were transformed into smartFilm granules via wet granulation and the resulting norfloxacin-loaded smartFilm granules were transformed into norfloxacin-loaded tablets made from paper, i.e., smartFilm tablets. The crystalline state of norfloxacin was investigated, as well as the pharmaceutical properties of the granules and the tablets. The bioactivity of the smartFilm tablets was assessed in vitro and ex vivo to determine the antibacterial activity of norfloxacin. The results were compared to a physical mixture tablet that contained non-loaded paper granules and equal amounts of norfloxacin as a crystalline powder. (3) Results: Norfloxacin-loaded smartFilm granules and norfloxacin-loaded smartFilm tablets contained norfloxacin in an amorphous state, which resulted in an improved and faster release of norfloxacin when compared to the physical mixture tablet. The bioactivity was up to three times higher when compared to the physical mixture tablet. The ex vivo model was demonstrated to be a useful tool that allows for a fast and cost-effective discrimination between "good" and "bad" formulations. It provides realistic physiological conditions and can therefore yield meaningful, additional biopharmaceutical information that cannot be assessed in classical in vitro experiments. (4) Conclusions: smartFilm tablets are a promising, universal, industrially feasible and cost-effective formulation strategy for improved solubility and enhanced bioactivity of poorly soluble drugs. [ABSTRACT FROM AUTHOR]

The manufacturing of paper with new functional properties is a current problem today. A method of modifying the surface layer of paper by the partial dissolution of cellulose on its surface is proposed. N-Methylmorpholine-N-oxide (NMMO) is proposed for use as a solvent, the regeneration of which provides an environmentally friendly process. It was shown that among the possible hydrate forms of the solvent, the monohydrate and higher-melting forms are optimal for modifying the paper surface. The temperature–time modes of processing were revealed and the weight gain and density increase in the course of modification were estimated. The structural and morphological features of the original and modified paper were studied by X-ray imaging and scanning microscopy. The NMMO surface treatment makes it possible to vary the air permeability of the paper, making it practically non-permeable. The capillary and pore system were radically transformed after the partial dissolution of cellulose and its coagulation, as the formed cellulose film isolates them, which leads to a decrease in surface absorbency. The processing conditions allowing for the optimization of the optical and strength properties of the modified paper samples are revealed. The resulting paper with a modified N-methylmorpholine-N-oxide surface layer can be used for printing valuable documents. [ABSTRACT FROM AUTHOR]

During the storage of celluloid pictures for animation films over half a century, an interleave paper adhered to acrylic paint. The purpose of this study is to establish a methodology to cleanly remove the paper from the paint. A layered film, a replica of the celluloid pictures, adhered with paper was prepared and immersed in water or ethanol. The effect of these solvents on the peeling behavior was investigated using a peel test. The maximum peel force for the dry layered film in was distributed at ~0.5 N, independently of the peel speed. The peel force was significantly reduced after the layered film was immersed in pure water or ethanol. A morphological observation revealed that the dry paper was peeled off via the cohesive failure of the paper. After the layered film was immersed in pure water, the paper was also peeled off via cohesive failure. The layered film immersed in ethanol was peeled off at the paper/paint interface. To clear the effect of the volume change in the paint on peel behavior, the relative volume was determined via image analysis. The relative volume of paint was 1.56 in pure water and 1.37 in ethanol. It can be considered that the large difference in the volume of paint induces a large shear stress at the paint/paper interface. [ABSTRACT FROM AUTHOR]

This paper presents the limitations and potential of ATR-FTIR spectroscopy applied to the study of cellulosic textile collections The technique helps to differentiate natural fibres according to the content of lignin, pectin, hemicellulose, and wax, although some problematic issues should be considered. The spectral differences derived from the environmental humidity uptake and the plant composition are reviewed and discussed in the light of new experimental data. Diagnostic bands are proposed that can discriminate between different fibres from different plants. The contribution of ageing is also considered, demonstrating that sometimes aged fibres cannot be reliably recognised. In contrast, the potential of ATR-FTIR spectroscopy to discriminate between natural and modified fibres is discussed and proven. The best results were obtained when microinvasive ATR-FTIR spectroscopy was coupled with SEM observations. The proposed protocol was tested on microsamples of various cellulosic materials from traditional Japanese samurai armours dating from the 16th to the 20th centuries (Morigi Collection, Museo delle Culture, Lugano, Switzerland). The results facilitated a complete characterisation of the materials and demonstrated that the protocol can be used to study a wide variety of cellulosic materials, including both natural and man-modified fibres, and paper. [ABSTRACT FROM AUTHOR]

All-lignin coating formulations were prepared while combining water-soluble cationic kraft lignin (quaternized LignoBoost®, CL) and anionic lignosulphonate (LS). The electrostatic attraction between positively charged CL and negatively charged LS led to the formation of insoluble self-organized macromolecule aggregates that align to films. The structures of the formed layers were evaluated by atomic force microscopy (AFM), firstly on glass lamina using dip-coating deposition and then on handsheets and industrial uncoated paper using roll-to-roll coating in a layer-by-layer mode. Coated samples were also characterized by optical microscopy, scanning electron microscopy (SEM) coupled with energy dispersive spectroscopy (SEM/EDS), and contact angle measurements. It was suggested that the structure of all-lignin aggregates is the result of the interaction of amphiphilic water-soluble lignin molecules leading to their specifically ordered mutual arrangement depending on the order and the mode of their application on the surface. The all-lignin coating of cellulosic fiber imparts lower air permeability and lower free surface energy to paper, mainly due to a decrease in surface polarity, thus promoting the paper's hydrophobic properties. Moderate loading of lignin coating formulations (5–6 g m−2) did not affect the mechanical strength of the paper. [ABSTRACT FROM AUTHOR]

Herein is presented a novel and efficient portable paper-based sensing platform using paper-incorporated histidine stabilized gold nanoclusters (His-AuNCs), for the sensitive and selective detection of Fe ions from low-volume real water samples based on photoluminescence (PL) quenching. Highly photoluminescent colloidal His-AuNCs are obtained via a novel microwave-assisted method. The His-AuNCs-based sensor reveals a limit of detection (LOD) as low as 0.2 μM and a good selectivity towards Fe ions, in solution. Further, the fabricated portable sensing device based on paper impregnated with His-AuNCs proves to be suitable for the easy detection of hazardous Fe levels from real water samples, under UV light exposure, through evaluating the level of PL quenching on paper. Photographic images are thereafter captured with a smartphone camera and the average blue intensity ratio (I/I0) of the His-AuNCs-paper spots is plotted against [Fe2+] revealing a LOD of 3.2 μM. Moreover, selectivity and competitivity assays performed on paper-based sensor prove that the proposed platform presents high selectivity and accuracy for the detection of Fe ions from water samples. To validate the platform, sensing assays are performed on real water samples from local sources, spiked with 35 μM Fe ions (i.e., Fe2+). The obtained recoveries prove the high sensitivity and accuracy of the proposed His-AuNCs-paper-based sensor pointing towards its applicability as an easy-to-use, fast, quantitative and qualitative sensor suitable for on-site detection of toxic levels of Fe ions in low-volume real water samples. [ABSTRACT FROM AUTHOR]

Many orally administrated drugs exhibit poor bioavailability due to their limited solubility. The smartFilm technology is an innovative approach to improve the drug aqueous solubility, where the drug is embedded within the matrix of cellulose-based paper in an amorphous state, hence increasing its solubility. Despite its proven effectiveness, smartFilms, i.e., pieces of paper, exhibit limited flowability and are not easy to swallow, and thus oral administration is not convenient. In addition, there is a lack of knowledge of their mechanical behavior under compression. This study aimed to transform unloaded smartFilms, i.e., paper, into a flowable physical form and investigated its mechanical behavior when compressed. Granules made of paper were prepared via wet granulation and were compressed into tablets. The influence of using different amounts and forms of sucrose, as a binder, on the pharmaceutical properties of the produced granules and tablets was studied and the most suitable composition was identified by using instrumented die experiments. For this, the Poisson's ratio and Young's modulus were determined for different compaction force levels and the deformation behavior was estimated with the Heckel mathematical model. All granule batches showed good flowability with angle of repose values between 25–35°. Granule batches with ≤30% dry sucrose content produced tablets that fulfilled the European Pharmacopeia requirements, and the compaction behavior of the granules was found to be comparable to the behavior of classical binders and compression enhancers. Paper can be transferred into granules. These granules can be used as suitable intermediate products for the production of tablets made of paper in large, industrial scale. [ABSTRACT FROM AUTHOR]

Rapid, simple, and sensitive analysis of relevant proteins is crucial in many research areas, such as clinical diagnosis and biomarker detection. In particular, clinical data on cancer biomarkers show great promise in forming reliable predictions for early cancer diagnostics, although the current analytical systems are difficult to implement in regions of limited recourses. Paper-based biosensors, in particular, have recently received great interest because they meet the criteria for point-of-care (PoC) devices; the main drawbacks with these devices are the low sensitivity and efficiency in performing quantitative measurements. In this work, we design a low-cost paper-based nanosensor through plasmonic calligraphy by directly drawing individual plasmonic lines on filter paper using a ballpoint pen filled with gold nanorods (AuNR) as the colloidal ink. The plasmonic arrays were further successively coated with negatively and positively charged polyelectrolyte layers employed as dielectric spacers to promote the enhancement of the emission of carboxyl-functionalized quantum dots (QD)—previously conjugated with specific antibodies—for indirect detection of the carcinoembryonic antigen-related cell adhesion molecule 5 (CEACAM5). The efficiency, sensitivity, as well as the specificity of our portable nanosensor were validated by recording the luminescence of the QD@Ab complex when different concentrations of CEACAM5 were added dropwise onto the calligraphed plasmonic arrays. [ABSTRACT FROM AUTHOR]

Most power transformers are oil-immersed transformers for which its insulation system consists of oil and cellulosic solid. The insulation liquid impregnates the solid-covering air spaces, which improves the efficiency of the insulation system. Not only does the oil ensure electrical insulation but it also works as coolants transferring the heat generated during transformer operation to the exterior of the transformer. Throughout normal operation conditions, transformers experience multiple stresses that degrade their insulation. Since the lifetime of oil-immersed transformers is defined mainly by the state of the insulation paper, it is critical to understand the behavior and degradation mechanisms of new insulation systems that try to overcome the drawbacks of mineral oil as well as to improve power transformer performances. The current increased prevalence of the nonlinear loads additionally stresses power transformers, which generates their premature ageing or even failure. Consequently, new materials and assessment methods are required to guarantee the suitable management of power transformer populations. In this Special Issue "Experimental and Numerical Analysis of Thermal Ageing in Power Transformers", four papers have been published. The guest editor also describes briefly some challenges involved beyond the coverage of this Special Issue. [ABSTRACT FROM AUTHOR]

Paper aging and protection processes play an essential function in the preservation of library collections and archives. In this study, some physical-mechanical properties of paper samples from XXth century books (private collections), such as pH acidity, tensile strength, and modulus of elasticity, as well as optical properties, such as absolute change in yellowness, were examined before and after treating them with hydroxyapatite nanoparticles (HAp). Accelerated light aging was also evaluated and discussed. The treatment with HAp nanoparticles increased the paper's pH to slightly alkaline values (approximately pH 8). Washing and treating the paper improved its mechanical properties compared to untreated paper; the tear length increased by 35% and the modulus of elasticity increased by 56%. That the treated and aged samples are more elastic than the original samples demonstrates that HAp nanoparticles consolidated the cellulose fibers. Additionally, particle morphology, size, composition and size distribution were assessed via image analysis using scanning electron microscopy (SEM-EDX), atomic force microscopy (AFM), and the ImageJ processing program. [ABSTRACT FROM AUTHOR]

(1) Background: Numerous oral drugs exhibit limited bioavailability due to their poor solubility and poor intestinal permeability. The smartFilm technology is an innovative approach that improves the drug aqueous solubility via incorporating the drug in an amorphous state into a cellulose-based matrix, i.e., paper. smartFilms can be transformed into a free-flowing physical form (i.e., paper granules) that can be compressed into tablets with optimum physico-chemical and pharmaceutical properties. The aim of this study was to investigate if smartFilm tablets are suitable for improved oral delivery of poorly water-soluble drugs. (2) Methods: Curcumin is a poorly soluble drug with low intestinal permeability and was used for the production of curcumin-loaded smartFilms. The curcumin-loaded smartFilms were transferred into smartFilm granules which were then compressed into curcumin-loaded smartFilm tablets. The tablets were characterized regarding their physico-chemical and pharmaceutical properties, and the intestinal permeability of curcumin was determined with the ex vivo porcine intestinal model. The ex vivo intestinal permeability of curcumin from the smartFilm tablets was compared to a physical mixture of curcumin and paper and to a classical and to an innovative commercial product, respectively. (3) Results: The produced curcumin-loaded smartFilm tablets fulfilled the European Pharmacopoeia requirements, incorporated curcumin in amorphous state within the cellulose matrix and exhibited an enhanced dissolution rate. The ex vivo intestinal permeation data were shown to correlate to the in vitro dissolution data. The ex vivo intestinal permeation of curcumin from the smartFilm tablets was about two-fold higher when compared to the physical mixture and the classical commercial product. No differences in the ex vivo bioavailability were found between the smartFilm tablets and the innovative commercial product. (4) Conclusions: smartFilm tablets are a cost-effective and industrially feasible formulation approach for the formulation of poorly water-soluble drugs, i.e., BCS class II and IV drugs. [ABSTRACT FROM AUTHOR]

The hydroxyl groups on the cellulose macromolecular chain cause the cellulose surface to have strong reactivity. In this study, 1H, 1H, 2H, 2H-perfluorodecyltriethoxysilane (PDOTES) was used to modify cellulose to improve its triboelectric properties, and a triboelectric nanogenerator (TENG) was assembled. The introduction of fluorine groups reduced the surface potential of cellulose and turned it into a negative phase, which enhanced the ability to capture electrons. The electrical properties increased by 30% compared with unmodified cellulose. According to the principles of TENGs, a self-powered human-wearable device was designed using PDOTES-paper, which could detect movements of the human body, such as walking and running, and facilitated a practical method for the preparation of efficient wearable sensors. [ABSTRACT FROM AUTHOR]

Hydrogen sulfide (H2S) is known to participate in bacteria-induced inflammatory response in periodontal diseases. Therefore, it is necessary to quantify H2S produced by oral bacteria for diagnosis and treatment of oral diseases including halitosis and periodontal disease. In this study, we introduce a paper-based colorimetric assay for detecting bacterial H2S utilizing silver/Nafion/polyvinylpyrrolidone membrane and a 96-well microplate. This H2S-sensing paper showed a good sensitivity (8.27 blue channel intensity/μM H2S, R2 = 0.9996), which was higher than that of lead acetate paper (6.05 blue channel intensity/μM H2S, R2 = 0.9959). We analyzed the difference in H2S concentration released from four kinds of oral bacteria (Eikenella corrodens, Streptococcus sobrinus, Streptococcus mutans, and Lactobacillus casei). Finally, the H2S level in Eikenella corrodens while varying the concentration of cysteine and treatment time was quantified. This paper-based colorimetric assay can be utilized as a simple and effective tool for in vitro screening of H2S-producing ability of many bacteria as well as salivary H2S analysis. [ABSTRACT FROM AUTHOR]

There is current interest in replacing petroleum-based additives in consumer paper products with abundantly available, renewable and sustainable biopolymers such as lignin-containing cellulose nanofibers (LCNFs) and cottonseed protein. This research characterized the performance of cottonseed protein isolate with/without LCNFs to increase the dry strength of filter paper. The application of 10% protein solution with 2% LCNFs as an additive improved the elongation at break, tensile strength and modulus of treated paper products compared to the improved performance of cottonseed protein alone. Improvements in tensile modulus and tensile strength were greatest for samples containing larger amounts of lignin and a greater degree of polymerization than for those with less lignin from the same biomass sources. [ABSTRACT FROM AUTHOR]

Hydrophobic coatings are of utmost importance for many applications of paper-based materials. However, to date, most coating methods demand vast amounts of chemicals and solvents. Frequently, fossil-based coating materials are being used and multiple derivatization reactions are often required to obtain desired performances. In this work, we present a solvent-free paper-coating process, where olive oil as the main biogenic component is being used to obtain a hydrophobic barrier on paper. UV-induced thiol-ene photocrosslinking of olive oil was pursued in a solvent-free state at a wavelength of 254 nm without addition of photoinitiator. Optimum reaction conditions were determined in advance using oleic acid as a model compound. Paper coatings based on olive oil crosslinked by thiol-ene reaction reach water contact angles of up to 120°. By means of Fourier transform infrared spectroscopy and differential scanning calorimetry, a successful reaction and the formation of a polymer network within the coating can be proven. These results show that click-chemistry strategies can be used to achieve hydrophobic polymeric paper coatings while keeping the amount of non-biobased chemicals and reaction steps at a minimum. [ABSTRACT FROM AUTHOR]