Search

Paper with simultaneous fire-resistance and hydrophobicity have greatly potential applications in the fields of packing, storage and delivering information, which attracts increasing attention recently. Different from the traditional cellulose-based paper which is extremely easily damaged by water and fire, a new type of highly flexible, fire-resistant and hydrophobic paper based on Si 3 N 4 nanowires and polydimethylsiloxane (PDMS) is reported. Specially, the Si 3 N 4 @PDMS core-shell nanowires with 3D interlocking structure are designed, in which the Si 3 N 4 nanowires act as the inorganic fire-resistant frameworks and the PDMS shell with low surface energy provides the hydrophobic surface. The Si 3 N 4 @PDMS core-shell nanowires are intertwined and interlaced to form a highly flexible Si 3 N 4 @PDMS paper. The tensile strength of Si 3 N 4 @PDMS paper is 6.19 MPa, indicating the good mechanical property. The obtained Si 3 N 4 @PDMS paper has the characteristics of writability, fire-resistance and hydrophobicity. The high thermal stability of Si 3 N 4 nanowires makes Si 3 N 4 @PDMS paper exhibit excellent fire resistance. No obvious change is observed for the commercial paper with Si 3 N 4 @PDMS paper as the fire-shielding layer after heating for 30 min. In addition, the contact angles of water droplets are all greater than 110° over the surfaces of Si 3 N 4 @PDMS paper after mechanical damages, chemical corrosions and thermal treatments. Si 3 N 4 @PDMS paper can be used in oil/water separation and oil collection. More importantly, Si 3 N 4 @PDMS paper can be used for writing without being damaged by fire or water. The present work may inspire the development and application of functional paper and is expected to become a breakthrough in the traditional paper industry. [ABSTRACT FROM AUTHOR]

The development of self-powered UV photodiode on green substrate is still a challenge. In this study, highly conductive Al doped ZnO (AZO) film was sputter-deposited on paper substrate at room temperature; subsequently, paper-based Schottky photodiodes were successfully fabricated by following Au-ZnO-Al and Au-ZnO-AZO-Al structure designs, respectively. These UV light-based devices operate successfully without external power. Au-ZnO-AZO-Al photodiode shows improved response and faster speed compared to Au-ZnO-Al photodiode. The one-dimensional Poisson simulation results demonstrate that the improvement is attributed to the strong electric field in the ZnO-AZO n-n+ high-low junction, thus, enhancing the collection rate and drifting speed of the photogenerated carriers. In addition, AZO can form favorable ohmic contact with the Al electrodes, further improving the device performance. The photo-response of the paper-based photodiode device shows high reproducibility and stability. Based on these outstanding results, we conclude that these paper-based electronic devices have great potential to replace conventional petroleum-based flexible electronic devices, thus, contributing to the green/sustainable development. [ABSTRACT FROM AUTHOR]

[Display omitted] • Multi-layer forming technology can integrate triboelectric material with electrode. • The all CPTENGs can exhibit excellent humidity, acid and alkali resistance. • The CPTENGs can yield a V OC , I SC and power density of 227.1 V, 6.9 μA and 520 mW/m2. • Matching CPTENGs with P-ZISC can obtain a self-charging power system (PSCPS). • The PSCPS can drive some miniaturized electronics for a long time. Triboelectric nanogenerators (TENGs) are regarded as a promising technology to drive the development of flexible/wearable electronics and self-powering sensor. Application of cellulose paper as the triboelectric positive materials makes TENGs more environmentally friendly. However, the limited output performance and stability in harsh environments and oxidation and corrosion of the metal electrodes have limited the practical application of cellulose paper based triboelectric nanogenerators (CPTENGs). Here, we have integrated cellulose paper-based triboelectric material and electrode in one sheet by using multi-layer forming technology in paper industry; the upper triboelectric layer shows excellent triboelectric positive performance, hydrophobicity and acid and alkali resistance, while the bottom electrode exhibits promise conductivity. The all CPTENGs can yield a maximum open-circuit voltage (V OC) of 227.1 V, a short-circuit current (I SC) of 6.9 μA. Furthermore, the V OC values of the all CPTENGs increase from 0.02 V to 225.1 V at the load resistance of 100 Ω∼10 GΩ; and a power density of 520 mW·m−2 is also obtained at a load resistance of 30 MΩ. Moreover, the V OC of CPTENGs not only retains up to 78 % of its initial value at a high relative humidity of 90 %, but also almost maintains unchanged in a wide range of the pH environment (pH = 1∼13). More importantly, the CPTENGs can be readily matched with paper-based zinc supercapacitor (P-ZISC) to act as an all paper based self-charging power system (PSCPS). The PSCPS is capable of driving various miniaturized electronics, such as electronic watch, temperature/humidity indicator, demonstrating its potential application in a sustainable power source for portable and green electronics. [ABSTRACT FROM AUTHOR]

Predictive models for the transport of volatile organic compounds in paper need to consider the complex interplay of diffusion, adsorption, desorption, or chemical reactions. The relative importance of each of these processes is determined by the polarity of the volatile. Hence, it is challenging to pick a valid theoretical model that correctly predicts transport regardless of the polarity. Here, physics-informed neural networks (PINNs) assess which of five different models correctly describe transport of DMSO as polar and n-tetradecane as apolar model compound: (i) a pseudo first-order adsorption model for an irreversible sorption process, (ii) a first-order kinetics model allowing reversible sorption, (iii) a second-order model with a reversible process, and an effective diffusion model accounting for a constant (iv) and for a variable effective diffusivity (v). Each tested model is given as set of partial differential equations (PDE). Considering the model under testing and experimentally obtained spatially and temporally resolved concentration profiles through stacks of paper sheets, PINNs predict concentration of the volatiles and associated material constants such as sorption constants and effective diffusion coefficients by solving the inverse problem. Our PINNs revealed two models, pseudo first-order sorption and second-order reversible sorption, that correctly predict concentration profiles and polarity-driven differences in sorption times. While a PINN-based picking of valid transport models has important implications for the development of effective methods for controlling emission of volatiles from paper materials, PINNs represent a versatile mathematical tool to validate or refute the capability of PDE-based theoretical models to describe experimental data. • PINNs evaluate sorption kinetics in porous materials. • Focus: Transport of organic volatiles in cellulose. • Pseudo first-order model suits organic volatiles. • Predicting transport of volatiles through paper. [ABSTRACT FROM AUTHOR]

[Display omitted] • Honeycomb panels with discrete arranged block reinforcements were numerically designed. • The elastic moduli of the new honeycomb panels are higher than those of heavier panels with slatted. • Tables with new cellular panels are characterized by a stiffness of 85 % of the stiffness of heavier tables with slats. Furniture manufacturers indicate they know the benefits of lightweight honeycomb panels but still expect their higher mechanical properties. This work presents a numerical and experimental approach to designing new tables manufactured of paper honeycomb panels with discreetly arranged reinforcing blocks in the core. The main goal was to determine whether the discrete arrangement of the blocks affects the strength and amount of energy absorbed by the newly designed tables and stiffness of honeycomb panels. Optimization reduced the weight of the panels by up to 30 %. At the same time, their linear elastic modulus was increased from 1579 MPa to 1771 MPa. After ten load cycles, tables with discrete reinforcements have a stiffness up 86.85–87.20 % of the stiffness of the reference table. After destructive tests up 89.96–91.16 %. Ultimately, the test results demonstrate the effectiveness of replacing wide slats with discreetly placed reinforcing blocks in the core structure. [ABSTRACT FROM AUTHOR]

[Display omitted] • For the first time the root cause for paper curl developing over days and weeks is described. • The curl of the paper sheets is caused by migration of co-solvents (e.g., glycerol) from the inkjet ink. • A 2D-laser scanner is utilized to investigate short- and long-term paper curl. • Glycerol migration in paper sheets is monitored using a combination of sheet splitting and subsequent HPLC analysis. The dimensional stability of paper during printing is crucial for ensuring production quality and runnability. However, inkjet printing faces inherent challenges due to the hygroscopic nature of paper and the use of water-based inks. Despite freshly printed sheets are flat, a considerable development of paper curl is often observed during storage. In this study, we establish the link between the migration of ink co-solvents and the long-term curl development of printed paper. A4 paper sheets were sprayed with a water-glycerol model ink and changes in the sheet's curvature were monitored using a 2D-laser sensor. We also investigated glycerol migration by splitting the sheets into layers and determining the glycerol distribution using high-performance liquid chromatography. Our results demonstrate the development of curl during storage as well as glycerol migration in thickness direction of the sheet, both on a comparable timescale. We thus propose that long term curl in inkjet printing can be caused by z-directional migration of the co-solvent (glycerol) over time. This study enhances understanding of the physical mechanisms that drive the long-term curl phenomenon in inkjet-printed sheets. The results can be used to optimize printing processes, allowing for the production of higher quality printed products with greater dimensional stability. [ABSTRACT FROM AUTHOR]

The high demand for flexible electroconductive elements, such as organic coatings, is associated with the development of IoT devices, wearable health monitoring devices, and similar devices. To meet cost and environmental standards, the ideal coating should use the richness of nature, be biodegradable, and be water soluble to avoid the use of harmful organic solvents. All of these criteria are met by the composite coating consisting of sodium lignosulfonate (SLS) and multiwall carbon nanotubes (MWCNTs). Furthermore, the SLS/CNT coating on paper substrates is highly electroconductive, hydrophobic, and resistant to annealing, high humidity, bending, and scratching. The electrical conductivity of the SLS/CNT coating varies depending on the substrate used, but it is highly conductive and resistant on all substrates tested. Most importantly, due to the use of abundant and mass produced and cheap materials, the price of a coating containing 77 wt% SLS and 23 wt% CNT, with a sheet resistance of 113 Ω/sq is estimated to be around 2.05 EUR/m2. This coating can be especially beneficial for large-scale applications, such as heating films. [Display omitted] • SLS is an affordable and readily available stabilizer for CNT dispersion in water. • SLS/CNT creates a highly conductive coating on cellulose substrates. • The SLS/CNT coating on paper has potential applications as cost-effective sensors or heaters. • The conductivity of the coating is influenced by the properties of the substrate. [ABSTRACT FROM AUTHOR]

[Display omitted] • Sonication improves the absorption of metallic salt in the paper. • Ultrasound catalyzes the synthesis of metallic nanoparticles. • A longer sonication time during salt absorption increases the number of nanoparticles obtained. • Nanoparticles obtained by sonochemistry are an easy and reproducible method to modify paper. This work focuses on a systematic method to produce Ag, Cu, and Ag/Cu metallic nanoparticles (MNPs) in situ assisted with ultrasound on cellulose paper. By tuning the concentration of AgNO 3 and CuSO 4 salt precursors and ultrasound time, combined with a fixed concentration of ascorbic acid (AA) as a reducing agent, it was possible to control the size, morphology, and polydispersity of the resulting MNPs on cellulose papers. Notably, high yield and low polydispersity of MNPs and bimetallic nanoparticles are achieved by increasing the sonication time on paper samples pre-treated with salt precursors before reduction with AA. Moreover, mechanical analysis on paper samples presenting well-dispersed and distributed MNPs showed slightly decreasing values of Young's modulus compared to neat papers. The strain at break is substantially improved in papers containing solely Ag or Cu MNPs. The latter suggests that the elastic/plastic transition and deformation of papers are tuned by cellulose and MNPs interfacial interaction, as indicated by mechanical analysis. The proposed method provides insights into each factor affecting the sonochemistry in situ synthesis of MNPs on cellulose papers. In addition, it offers a straightforward alternative to scale up the production of MNPs on paper, ensuring an eco-friendly method. [ABSTRACT FROM AUTHOR]

Point-of-care testing (POCT) technology is urgently required owing to the prevalence of the Internet of Things and portable electronics. In light of the attractive properties of low background and high sensitivity caused by the complete separation of excitation source and detection signal, the paper-based photoelectrochemical (PEC) sensors, featured with fast in analysis, disposable and environmental-friendly have become one of the most promising strategies in POCT. Therefore, in this review, the latest advances and principal issues in the design and fabrication of portable paper-based PEC sensors for POCT are systematically discussed. Primarily, the flexible electronic devices that can be constructed by paper and the reasons why they can be used in PEC sensors are expounded. Afterwards, the photosensitive materials involved in paper-based PEC sensor and the signal amplification strategies are emphatically introduced. Subsequently, the application of paper-based PEC sensors in medical diagnosis, environmental monitoring and food safety are further discussed. Finally, the main opportunities and challenges of paper-based PEC sensing platforms for POCT are briefly summarized. It provides a distinct perspective for researchers to construct paper-based PEC sensors with portable and cost-effective, hoping to enlighten the fast development of POCT soon after, as well as benefit human society. • The merits of functionalized paper for PEC sensor are introduced. • Photosensitive material and signal amplification strategy of paper-based PEC sensor are discussed. • The application of paper-based PEC sensor in the field of POCT is highlighted. • The limitations and challenges of paper-based PEC sensor are summarized. [ABSTRACT FROM AUTHOR]

In the past few years, point-of-care testing (POCT) technology has crossed the boundaries of laboratory determination and entered the stage of practical applications. Herein, the latest advances and principal issues in the design and fabrication of paper-based bipolar electrode electrochemiluminescence (BPE-ECL) sensors, which are widely used in the POCT field, are highlighted. After introducing the attractive physical and chemical properties of cellulose paper, various approaches aimed at enhancing the functions of the paper, and their underlying principles are described. The materials typically employed for fabricating paper-based BPE are also discussed in detail. Subsequently, the universal method of enhancing BPE-ECL signal and improving detection accuracy is put forward, and the ECL detector widely used is introduced. Furthermore, the application of paper-based BPE-ECL sensors in biomedical, food, environmental and other fields are displayed. Finally, future opportunities and the remaining challenges are analyzed. It is expected that more design concepts and working principles for paper-based BPE-ECL sensors will be developed in the near future, paving the way for the development and application of paper-based BPE-ECL sensors in the POCT field and providing certain guarantee for the development of human health. • Preparation and application prospect of paper-based BPE-ECL sensor are discussed. • Approaches to boost functionalization of paper and existing limitations are described. • Fabricating BPE from classical electrode materials are introduced exhaustively. • Strategies of enhancing ECL signal to improve device sensitivity are displayed. [ABSTRACT FROM AUTHOR]

Synthetic cannabinoids (SC) are extremely prevalent within the prison system and cause problems for prisoners, law enforcement and health services. SC are often soaked into paper then posted into prisons therefore one of the aims of this research is to collaborate with Rapiscan Systems Ltd. and local prisons in England to measure the effectiveness of trace detection methods for the indication of SC in prison post using the Itemiser 3E®. To ensure compounds did not go undetected, samples with Ion Trap Mobility Spectrometry™ peaks indicative of synthetic cannabinoids on the Itemiser 3E® were analysed using Gas Chromatography-Mass Spectrometry, Liquid Chromatography-Quadrupole Time-of-Flight Mass Spectrometry and Nuclear Magnetic Resonance Spectroscopy to identify chemical characteristics which allowed comparison to reference spectra. Sample data spanning three years from one prison's Itemiser 3E® were collated to identify trends in drug prevalence and the influence of library updates. To date, the method has identified four compounds: 5F‐MDMB‐PICA, MMB-4en-PICA, 4F‐MDMB‐BUTINACA and MDMB-4en-PINACA on prison post which were not already included on, or needed confirmatory analysis to update, the Itemiser 3E® library. As a result, the libraries on prison Itemiser 3E®s have been updated to ensure future detection of such compounds. Trends and influences from the processed Itemiser 3E® data were also reported back to the West Midlands Prison Group. This research directly benefitted both the West Midlands Prison Group and Rapiscan Systems Ltd. and it is anticipated that the continuation of this research could be expanded to a national scale. • Prisons submitted samples for confirmatory analysis after screening by Itemiser 3E®. • GC-MS, LC-MS and NMR identified synthetic cannabinoids in eight of the 47 samples. • 5F‐MDMB‐PICA, MMB-4en-PICA, 4F‐MDMB‐BUTINACA and MDMB-4en-PINACA were identified. • Confirmatory analysis aided the generation of Itemiser 3E® library definitions. • This demonstrates the importance of the screening, confirmation and feedback cycle. [ABSTRACT FROM AUTHOR]

Janus membranes with unidirectional liquid transport property have tremendous applications in fields of functional fabrics, water harvesting, smart wound dressings and so on. Paper shows distinct advantages to other materials, such as hydrophilicity, low-cost, flexible and so on. However, there is still less attention on how to construct a Janus paper with unidirectional liquid transport capacity and its functional applications. Here, a multi-pores Janus paper with asymmetric wetting properties is developed through consecutive laser microdrilling, hydrophobic modification and air-plasma treatment. As a result, the prepared Janus paper can allow the water to transport from the hydrophobic side to the hydrophilic side, while it blocks the water to flow in the reverse direction. Meanwhile, it can also achieve antigravity unidirectional water transport. In addition, the mechanism for unidirectional liquid transport is investigated. Finally, as a proof-of-concept, the Janus paper is utilized for applications of information encryption/decryption. [Display omitted] • Multi-pores Janus paper is successfully reported in this manuscript through simple fabrication method. • The Janus paper can unidirectional transport water from the hydrophobic side to its hydrophilic side. • It can also achieve antigravity unidirectional water transport. • The multi-pores Janus paper is utilized for applications of information encryption/decryption. [ABSTRACT FROM AUTHOR]

Laser-induced graphene (LIG) is a foam-like porous material consisting of few-layer graphene obtained by laser irradiation of a wide range of carbon-containing substrates. Among these, the ability to synthesize LIG from paper and other cellulose-related materials is particularly exciting, as it opens the door to a wide assortment of potential applications in the form of low-cost, flexible, and biodegradable devices. Here, the synthesis of this material, dubbed paper-LIG , on different types of filter papers and xylan biopolymer is discussed. In particular, we report the formation of paper-LIG by single-step irradiation, providing an improvement over the conventional multiple lasing approach and giving an explanation of the conditions that allow this simplified synthesis. All the relevant process parameters are covered, assessing their effect on the resulting electrical properties, structure, and morphology. Additionally, we demonstrate the application of LIG obtained from xylan, an abundant and often underutilized biopolymer, for temperature sensing. These results provide a better understanding of the conditions required for the synthesis of highly conductive LIG from paper and related materials, paving the way for its application, with reduced cost and low environmental impact, in fields ranging from biomonitoring to consumer electronics. [Display omitted] • Synthesis of laser-induced graphene from filter paper by a single irradiation step • Synthesis of laser-induced graphene by irradiation of filter paper containing activated charcoal • Laser-induced graphene from a xylan substrate, valorizing this underutilized natural product • Temperature sensor employing laser-induced graphene obtained from modified xylan [ABSTRACT FROM AUTHOR]

Triboelectric nanogenerators (TENGs) have been investigated as a promising device to harvest mechanical energy into electricity. At present, paper-based triboelectric nanogenerators (P-TENGs) have been widely researched because paper features with lightweight, low cost, abundance, renewability and biodegradability. In this paper, the operating principles and operation modes of TENGs, the development progress and performance enhancement routes of P-TENGs are comprehensively reviewed. Additionally, the overview, challenges and opportunities of P-TENGs applications are also presented. [ABSTRACT FROM AUTHOR]

Commercial copy paper is a thin sheet material that has orthotropic constitutive behavior reminiscent of Al foils. Similar to Al foils, mode I crack tips in paper developed quasistatic, fully plastic, steady-state conditions even though plastic deformation in paper is not isochoric. The characteristic steady-state stress for crack growth depended on specimen orientation and contained a positive offset stress due to fiber bridging ( σ c = 37.3 MPa, σ offset = 6.0 MPa and σ c = 20.1 MPa, σ offset = 2.9 MPa for the machine and cross direction orientations, respectively). Orientation-dependent, reversed plastic zones were observed in the crack wake and transverse necking fracture processes were not present. • Steady-state, mode I crack growth was observed in single-edge notched specimens. • Steady-state process zone sizes were directly measured from full-field strain maps. • The crack growth was controlled by a characteristic steady-state stress. • The characteristic steady-state stress was offset because of fiber bridging. [ABSTRACT FROM AUTHOR]

[Display omitted] • Novel dimer acid-based waterborne polyurethanes (DWPUs) were designed and prepared. • DWPUs were first used as multifunctional coatings for paper substrates. • Papers coated by DWPUs exhibited excellent water- and oil-resistances. • Alkyl and uniform membrane of DWPUs are critical to improve papers' properties. Paper derived from lignocellulose has great advantages over plastics as packaging material, nevertheless, the poor water- and oil-resistances of paper-derived products limited their application in high-end field. Herein, novel dimer acid-based waterborne polyurethanes (DWPUs) with different content of dimer acid-based polyester polyol (DG) were prepared and used as water- and oil-resistant coating for paper substrate. The effects of DG contents on water- and oil-resistances, mechanical properties and thermal stability of DWPUs coated papers were systematically investigated. When the content of DG reached up to 7 wt% (based on polyester glycol), the paper coated by DWPU exhibited 88.06% decrease in Cobb 60 value, 8.7 times increase in kit rating compared with uncoated paper. Meanwhile, DWPUs coated papers showed good mechanical properties and thermal stability. These improvements are attributed to the flexible long-alkyl chain, and six-ring structure of DWPUs as well as the continuous and homogeneous DWPU-derived membrane on the surface of paper. This study provides a new framework for the preparation of high quality, multifunctional, environmentally friendly water- and oil-resistant coatings for paper substrates. [ABSTRACT FROM AUTHOR]

The detection of trypsin and its inhibitor is significantly important for both clinical diagnosis and disease treatment. Herein, we demonstrate a hydrogel-assisted paper-based lateral flow sensor for the detection of trypsin and its inhibitor for the first time. The gelatin hydrogel is hydrolyzed based on the gel-to-sol transition in the presence of trypsin, which results in the release of the trapped water molecules in the gelatin hydrogel. By placing one end of a pH indicator strip onto the hydrolyzed gelatin hydrogel, water is flowing along the pH indicator strip. However, in the absence of trypsin, water cannot flow along the pH indicator strip as the water molecules are trapped in the gelatin hydrogel. The detection limit of the system reaches as low as 1.0 × 10−6 mg/mL, and it is also applied to the quantitative detection of trypsin in human serum. In addition, the detection of a clinical drug aprotinin that is an inhibitor of trypsin is also successfully achieved. Noteworthy, only the gelatin hydrogel, pH indicator strip, and PS substrate are needed to fulfill the detection of trypsin without the need of other chemicals or reagents. Overall, we develop a particularly simple, elegant, robust, competitive, high-throughput, and low-cost approach for the rapid and label-free detection of trypsin and its inhibitor, which is very promising in the development of commercial products for sensing, diagnostic, and pharmaceutical applications. Besides, the hydrogel-assisted paper-based lateral flow sensor can also be employed to detect other analytes of interest by use of different stimuli-responsive hydrogel systems. • A hydrogel-assisted paper-based lateral flow sensor is developed for the detection of trypsin and its inhibitor. • The hydrolysis of the gelatin hydrogel by trypsin triggers release of the water trapped in the hydrogel. • The released water flows along a pH indicator strip, and the coverage ratio of the water mark is used to quantify trypsin. • This simple, convenient, and cost-effective method has high portability, remarkable sensitivity, and fast response time. • It shows excellent performance in label-free and high-throughput detection of trypsin in human serum. [ABSTRACT FROM AUTHOR]