Search

• Comprehensive study on the Church of Ss. Annunziata in Paestum, Italy. • Utilization of extensive photogrammetric survey for accurate geometric modelling. • Dynamic characterization in Abaqus environment for material modelling and local failure mechanism assessment. • Analysis under varying seismic intensities to evaluate structural behaviour and vulnerability. • Insights aid informed decision-making for preservation and restoration efforts. This paper presents a comprehensive study on the Church of Ss. Annunziata in Paestum (Italy), focusing on its historical reconstruction, current condition analysis, and dynamic characterization. An extensive photogrammetric survey employing terrestrial and aerial photography was conducted to establish an accurate geometric model of the church. Subsequently, the model was set up into Abaqus ambiance for dynamic characterization, material modelling and assessment of potential local failure mechanisms through nonlinear dynamic analysis under varying seismic intensities. The research provides valuable insights into the structural behaviour of the church and its vulnerability to seismic events, aiding in informed decision-making for preservation and restoration efforts. [ABSTRACT FROM AUTHOR]

One of the main challenges for the construction of DEMO, the first fusion demonstration reactor, is the power exhaust issue. To deal with it, EUROfusion has undertaken the construction of DTT (Divertor Tokamak Test) facility which will be held in Frascati, Italy. It aims to test various divertor models which can be integrated and used under different plasma confinement configurations. The current design of DTT embed 54 divertor cassettes which must be anchored to the vacuum vessel using suitable fixation systems. This paper deals with the initial monotonic load assessment of the fixation system of the Fixation System which must ensure compliance with multiple design requirements. The Remote Handling compatibility is one of the most demanding, since it includes a preloading phase of the divertor necessary to mitigate the shaking of the cassette due to dynamic forces. Moreover, the system must withstand the conspicuous loads acting on the Divertor due to the full or partial loss of plasma confinement (Disruptive Events). Structural verifications through Finite Element Method (FEM) have been performed on the Divertor-Fixation System, considering a set of load combinations, with particular focus on the most demanding case related to Fast-transient Vertical Disruption Event-downward. [ABSTRACT FROM AUTHOR]

• The behavior of under-designed existing structures is investigated. • Traditional and innovative retrofitting are compared by a finite element analysis. • The innovative strategy provides a better nonlinear performance of the structure. • The presented strategy reduces the dynamic vulnerability of the existing structure. In the present paper the structural behavior of under-designed existing structures is investigated. The analyzed existing structure is assumed as originally designed in the past with respect to old codes and with respect to gravitational loads only. The under-designed structure is considered to be located in Italy in an area now classified by the new codes as high seismicity zone. In the investigation traditional and innovative steel braces are modeled and compared for the retrofitting of the structure by using a finite element analysis with a displacement based approach. With respect to a traditional retrofitting strategy the adopted retrofitting strategy with innovative steel braces allows a localization of the input seismic energy into the innovative steel braces which are endowed with dissipative properties and thus a better performance of the original existing structure is noted in the elastoplastic range. With respect to a traditional retrofitting system the innovative steel braces applied to under-designed existing structures show to provide a more robust nonlinear behavior of the under-designed structure and a significant reduction of the plasticization in the original existing structural frames when they are subject to dynamic events. These features are associated to a vulnerability reduction of the under-designed existing structure also at the ultimate limit state. [ABSTRACT FROM AUTHOR]

• This paper investigates the form of the Musmeci bridge over the Basento river. • Form-finding and design processes employed and constructive issues are discussed. • Aerial survey using a commercial UAV is used to derive a 3D geometric model. • Force density method with non-isotropic stresses is used to verify the original form. • The found form is verified by r-funicularity. The bridge over the Basento river in Potenza, Italy, designed by Sergio Musmeci, is supported by a continuous double-curvature RC shell optimized to reduce bending forces. This 300 m long bridge can be considered as a unique representative example of pioneering research on the design and construction of optimized structures. First, the design process employed for determining the form of the shell and the relevant constructive issues are described. A refined 3D geometric model of the shell is then obtained through an aerial survey carried out by a commercial UAV and a photogrammetric image-based reconstruction. A recent formulation of the Force Density Method allowing for non-isotropic stress state is exploited to numerically derive the form of the supporting shell; it is validated versus the surveyed geometry of the shell by employing a nonlinear optimization procedure in order to identify forces and stresses to be used as input parameters. Finally, the derived form of the shell is tested by a Finite Element analysis to verify its funicular efficiency, i.e., whether it is capable to withstand design loads by pure membrane actions. [ABSTRACT FROM AUTHOR]

This paper aims to present a new methodological approach for the stability assessment of coastal cliffs constituted of discontinuous rock masses. The method entails in situ specific geostructural and geomechanical surveys, three-dimensional UAV-based Photogrammetric structural models, laboratory geotechnical tests and, two- and three-dimensional finite element analysis (FEM). The application of the method to a case study is then presented and discussed; it regards a 600 m long sea rocky cliff located at Sant'Andrea (Melendugno, South of Apulia, SE Italy) and faced to the southern Adriatic Sea. Here the cliff is made up of an about 15 m-thick sequence of laminate calcisiltites alternate with bioturbated calcarenites belonging to the Uggiano la Chiesa Fm. (Middle-Upper Pliocene). The structural discontinuities detected with photogrammetry techniques were compared and validated with those derived from conventional in situ survey methods. Later on, the paper discusses assumptions and results of two- and three-dimensional finite element models developed to investigate the potential failure mechanisms of the sea cliff accounting for pre-existing weak planes or discontinuities with unfavourable orientation. The failure mechanisms obtained by both FEM analysis agree well with those typically observed in the study area. • Detailed 3-D geometrical survey of the cliff with UAV-based photogrammetry techniques; • Automatic detection of the most relevant fractures and joints from UAV surveys; • Geological, geostructural and geomorphological analysis of the cliff by means of in-situ surveys; • Detailed geotechnical characterization in the laboratory of the rock; • Failure mechanisms obtained with FEM analysis consistent with those typically observed in the study area; [ABSTRACT FROM AUTHOR]

• Use of the Cloud Analysis for the development of probabilistic fire demand models. • The LOCAFI localised fire model was used to model the effect of hydrocarbon pool fires. • Development of fire fragility functions of a steel pipe-rack. • The interstorey drift ratio – average maximum heat flux pair results the most efficient. This paper proposes a new method to build a probabilistic fire demand model (PFDM) to investigate the structural behaviour of a steel pipe-rack located within an industrial installation and exposed to a localised fire. The PFDM will serve to develop fire fragility functions to be used either in a fire risk assessment or in a fully probabilistic structural fire engineering (PSFE) framework. The cloud analysis (CA) was exploited to build a PFDM based on different engineering demand parameters (EDP) – intensity measures (IM) pairs. In particular, the analysis was applied to a prototype steel pipe-rack integrating an industrial plant in Italy. In order to cover a wide range of plausible fire scenarios and to introduce uncertainties in the fire model, 539 fire scenarios were examined by varying the fire diameter, the fire-structure distance and the fuel. The selection of the fire diameters was based on parametric analyses quantifying liquid flow through orifices and pipes. The thermal impact of the pool fires on the structure was analysed using the LOCAFI localised fire model and the thermo-mechanical response of the pipe rack was evaluated by means of finite element analysis. Based on the structural analysis outcomes, it was found that the interstorey drift ratio (ISDR) – maximum average heat flux impinging the structure (HF avg) EDP-IM pair was the most efficient and was also characterised by the highest relative sufficiency among the other pairs. Moreover, it has to be noted that for this type of case study, the CA revealed to be a viable option to build a PFDM. [ABSTRACT FROM AUTHOR]