Search

To develop special insulating paper is of great significance to promote the service life of transformers. Using molecular simulation to guide the development of special insulating paper can greatly reduce the trial-and-error rate and waste of resources in traditional experiments. The effect of different types of polysilsesquioxane (POSS) on cellulose insulating paper was investigated by using molecular simulation. This paper investigated the thermal stability and mechanical properties and electrical characteristics of caged POSS, semi-caged POSS, and ladder-like POSS doped cellulose insulating paper. The results show that POSS with all types can enhance the performance of cellulose insulating paper, and ladder-like POSS possess the best modification effect. The glass transition temperature was increased by 58 K, and the bulk modulus, shear modulus, and elastic modulus of cellulose insulating paper doped with ladder-like POSS can improve up to 27.07%, 45.67%, and 41.28%, respectively. Meanwhile, the dielectric properties of ladder-like POSS modified insulating paper are also significantly improved. The findings of this paper propose a method for the preparation of ladder-like POSS modified insulating paper, which provides theoretical guidance for the experimental preparation of special insulating paper. [ABSTRACT FROM AUTHOR]

This study investigated converting abundant paper mill waste, de‐inked paper sludge (DPS), into value‐added medium‐density fiberboard (MDF) panels. The objective was to repurpose this solid waste into a valuable material that aligns with the principles of a circular economy. Previous research has examined the addition of paper sludge to wood composites, but there is limited information on the specific incorporation of DPS into MDF production. This investigation offers new insights into this application. MDF panels were manufactured using hardwood fibers, with varying levels of urea‐formaldehyde resin (10% and 12% by weight) and different loadings of DPS (ranging from 0% to 50% by weight). X‐ray diffraction analysis revealed the presence of defective DPS fiber crystals. Contact angle measurements confirmed that DPS had poor wettability, corresponding to increased water absorption. As more DPS was incorporated, the mechanical properties of the panels progressively weakened due to defective fibers and poor adhesion between the fibers and the matrix. This was evident in scanning electron microscopy micrographs, which showed an escalation in interfacial flaws. Increasing the resin dosage noticeably improved the internal bond strength and reduced moisture uptake across all levels of DPS. However, at a DPS loading of 50%, the properties of the panels deteriorated by 36%–57% compared to the control MDF. Additionally, thickness swelling and water absorption increased significantly with higher DPS content, primarily due to the hydrophilic nature of the fibers. Based on optimization, it was determined that a DPS loading of 20% with a resin content of 12% provided the best balance between performance, waste utilization, cost, and moisture resistance. The reuse of abundant paper sludge supports the goals of a circular economy. However, strategies are required to tailor the processing methods and enable higher levels of recycled material without excessively compromising the key attributes of the product. Further research should focus on enhancing the quality of DPS and its compatibility with wood fibers and resin to enhance the performance of the composite material. Highlights: DPS from recycled paper mill assessed for MDF production with wood fibers and resinIncreasing DPS loading caused reductions in strength and adhesion of panelsWater absorption and thickness swelling markedly rose with more DPS additionIt was attributed to hydrophilic fibers and disrupted fiber‐matrix bondingOptimal formulation was 20% DPS loading and 12% resin content, balancing performance, waste utilization, and cost. [ABSTRACT FROM AUTHOR]

The filter paper (FP) method, a cost-effective, versatile, and convenient approach, has found extensive application in analyzing fine-grained soils, enabling the successful measurement of a broad spectrum of total and matric suctions. However, using the FP method in sand with a limited range of suction profiles has been notably underrepresented in the existing literature. Therefore, this study investigated the applicability of the contact FP method in establishing soil water retention curves (SWRCs) using five distinct FP calibration curves for 10 poorly graded sands. Among these calibration curves, the one presented by Chandler yielded the highest suction values, which were followed by those of ASTM. Furthermore, the FP results were subjected to fitting with a mathmatical model, which led to the observation that the overall trends in the obtained SWRCs displayed smooth sigmoidal shapes, resulting in a complete and coherent SWRCs. The SWRC results of five sand samples were assessed through validation against the hanging column technique (HCT) results, indicating a high degree of concordance and affirming the suitability of the FP method for sands characterized by a limited suction profile. Notably, the entire range of suction values fell within the 0.01–20 kPa range based on the calibration curves presented by Chandler and ASTM for all the examined sand samples, except sands 9 and 10. Furthermore, the suction values were unobtainable using the two aforementioned calibration curves within the ranges of 0.01–1.47 kPa and 0.01–0.172 kPa. [ABSTRACT FROM AUTHOR]

Polyethylene-, polyvinylidene chloride-, and per- and polyfluoroalkyl substance-coated paper generate microplastics or fluorochemicals in the environment. Here, we report an approach for the development of oil-resistant papers using an environmentally friendly, fluorine-free, water-dispersible poly(dimethylsiloxane) (PDMS) coating on kraft paper. Carboxylic-functionalized PDMS (PDMS-COOH) was synthesized and subsequently neutralized with ammonium bicarbonate to obtain a waterborne emulsion, which was then coated onto kraft paper. The water resistance of the coated paper was determined via Cobb60 measurements. The Cobb60 value was reduced to 2.70 ± 0.14 g/m2 as compared to 87.6 ± 5.1 g/m2 for uncoated paper, suggesting a remarkable improvement in water resistance. Similarly, oil resistance was found to be 12/12 on the kit test scale versus 0/12 for uncoated paper. In addition, the coated paper retained 70–90% of its inherent mechanical properties, and more importantly, the coated paper was recycled via pulp recovery using a standard protocol with a 91.1% yield. [ABSTRACT FROM AUTHOR]

Sensitizers are used to prepare photosensitive materials for ink-printing and thermal-recording media. Typical sensitizers contain an aromatic ring and exhibit aryl hydrocarbon receptor-mediated activity. They can accumulate in aquatic biota, leading to the disruption of ecosystems. Effluent from paper recycling plants has been identified as a source of contamination, and the presence of sensitizers in toilet paper may represent a new source of contamination in aquatic environments. To examine possible sources of contamination by sensitizers, this study investigated the levels of sensitizers in recycled toilet paper. We also studied the prevalence of sensitizers in rivers receiving effluents from sewage treatment plants in Japan, from 2020 to 2022. We detected eight sensitizers and related compounds in both toilet paper and river water samples; their total concentrations ranged from 0.78 to 34 µg/g (mean: 12 µg/g) in toilet paper and 58–1167 µg/L (median: 77 µg/L) in water. In the water samples, sensitizers were partitioned between liquid and suspended solid phases, and in suspended solids, sensitizers accounted for an average of 42% of the total. Correlation analysis showed a high correlation between sensitizer composition in the water from a river receiving sewage treatment plant effluents and toilet paper. Since these compounds were also detected in the river water analyzed in this study, toilet paper should be considered a novel source of sensitizers contamination in sewage treatment systems. [ABSTRACT FROM AUTHOR]

• Pulp and paper mill sludge (PPMS) landfill sites have GHG assessment challenges. • GHG fluxes measured by chambers with (F +) and without (F-) a frame were compared. • Flux relationships up to 80 % were shown between F- and F + chambers (the standard) • Correction factors for F- chambers were built to estimate fluxes from F + chambers. • The approach can refine GHG inventories on PPMS landfill sites. Assessments of greenhouse gas (GHG) emissions in managed areas are facing various challenges. A non-flow-through, non-steady-state (NFT-NSS) chamber coupled to a frame permanently inserted into the landfilled substrates is a standard method for quantifying GHG emissions in managed areas, such as pulp and paper mill sludge (PPMS) landfill sites. Frequent measurements are needed to minimize uncertainties on GHG emission factors at the landfill site scale. However, maintaining a frame inserted into the substrates for a long time period is often impossible due to landfilling management operations. Therefore, GHG measurements using NFT-NSS chambers placed directly on substrates' surface could be an interesting option. Our objectives were to determine the relationships between CO 2 , CH 4 , and N 2 O fluxes measured with (F +) and without (F-) a frame inserted in the substrates' surface and to develop correction factors for fluxes measured without a frame. Measurements were made at different PPMS landfill sites in the province of Québec, Canada. Stronger GHG flux relationships were observed at the provincial (across sites) than the specific site scale: the variance in GHG fluxes from F- chambers explained up to 80 % of variance in fluxes from F + chambers. The measured CO 2 , CH 4 , and N 2 O fluxes in F- chambers were on average 53, 78, and 63 % lower, respectively, than those estimated by the models at provincial scale. The correction factors developed with this approach could greatly extend the number of sites where in situ GHG measurements can be done and would help refining GHG inventories at the provincial and national levels. [ABSTRACT FROM AUTHOR]

Purpose: This paper aims to study the application of high-tolerance and flexible indigenous bacteria and fungi, along with the co-metabolism in recycled paper and cardboard mill (RPCM) wastewater treatment (WWT). Design/methodology/approach: The molecular characterization of isolated indigenous bacteria and fungi was performed by 16S rRNA and 18S rRNA gene sequencing, respectively. Glucose was used as a cometabolic substrate to enhance the bioremediation process. Findings: The highest removal efficiency was achieved for both chemical oxygen demand (COD) and color [78% COD and 45% color removal by Pseudomonas aeruginosa RW-2 (MZ603673), as well as approximately 70% COD and 48% color removal by Geotrichum candidum RW-4 (ON024394)]. The corresponding percentages were higher in comparison with the efficiency obtained from the oxidation ditch unit in the full-scale RPCM WWT plant. Originality/value: Indigenous P. aeruginosa RW-2 and G. candidum RW-4 demonstrated effective capability in RPCM WWT despite the highly toxic and low biodegradable nature, especially with the assistance of glucose. [ABSTRACT FROM AUTHOR]

The main part of companies in Bulgaria are built, however in the 70s, and upgraded last decade. The country supplies around 80 % of its supplies of paper, paperboard and pulp with own production. Integrated treatment of wastes is a priority for realizing closed life cycle of materials. The aim of the present work is to investigate the composition and other important characteristics of biomass wood ash wasted from paper industry. The correlations and associations among the chemical characteristics are also studied to find some basic trends and important relationships between two similar wastes from different enterprises. It was proved that all samples taken contained Ba, Cr, Mn, Ni, Co, Al, Fe, Cu and Zn far below the legal limits for such type of products. A product has a certain anti-acidic effect. The other positive result was that the content of iron is between 34 to 60 mg per 1 kg dry waste. The microscopic photos confirmed that the particles are close to the nano-size materials. The content of the elements C, N, H is in good quantities and ratios, which is a prerequisite for their use as a soil improver. By the results of this study, it was confirmed that all samples produced as a result of the thermal treatment and final low water content achieved are free from pathogen microorganisms and different weed seeds, affecting the yield and soil sustainability. That allows determining the optimal ratio between the used components with a view to obtain products with desired thermal stability and physico-chemical properties as soil improvers. [ABSTRACT FROM AUTHOR]

Recycled paper has become increasingly used as a raw material in the paper industry. However, hornification limits its application. Herein, the effect of recycling on the mechanical properties and microstructure of khasi pine pulp was systematically studied. The mechanical properties deteriorated and water retention value decreased after recycling. X-ray diffraction and Fourier-transform infrared spectroscopy revealed that cellulose crystallinity increased and partial cocrystallization occurred on cellulose microfibrils. Through the analysis of the morphology of secondary fibers by FQA, the loss of fine fibers caused by each reuse was found. Using the filtration method to prepare the recycled paper reduced the loss of fine fibers and improved the mechanical properties, with the tensile strength of a sample prepared using a sand core filter unit for five cycles (8.37 MPa) being like that of a sample prepared using a paper machine after one cycle. The investigation of the internal structure of the paper showed that the retained fine fibers were bonded between the long fibers, promoting the bonding between the fibers. Fine fibers improve the curling and twisting of fibers to some extent, especially in the first three recycling cycles. The hornification phenomenon of recycled paper was studied from the viewpoint of the fiber components, which is important to promote the development and application prospect of recycled paper. [ABSTRACT FROM AUTHOR]

This report presents an investigation into the use of carbon paper electrodes prepared from chitosan-adhered graphene magnetite nanoparticles for the analysis of Cr(VI). The preparation and storage of carbon paper electrodes is a simple process, and these electrodes are easier to replace than electrodes modified by more conventional methods. The electrochemical detection of Cr(VI) using square wave adsorption cathodic dissolution voltammetry (SWAdCSV) with high selectivity and sensitivity, as well as the optimum conditions for the preparation of the electrodes and the electrode parameters affecting the SWAdCSV signal, were the main points of focus of the investigation. Cr(VI) was detected linearly in the range of 4-40 μg L-1 with a detection limit of 2.84 μg L-1. The electrode output precision, calculated as %RSD, was 7.16% (n = 6), and this was the measurement used for the detection of Cr(VI) in standard and test samples with recoveries between 89% and 114%. The results were consistent with those obtained using the standard UV-Vis spectrophotometric method with a paired t-test at 95% confidence level. [ABSTRACT FROM AUTHOR]