Search

Gunshot wound analysis is an important part of medicolegal practice, in both autopsies and examinations of living persons. Well-established and studied simulants exist that exhibit both physical and biomechanical properties of soft-tissues and bones. Current research literature on ballistic wounds focuses on the biomechanical properties of skin simulants. In our extensive experimental study, we tested numerous synthetic and natural materials, regarding their macromorphological bullet impact characteristics, and compared these data with those from real bullet injuries gathered from medicolegal practice. Over thirty varieties of potential skin simulants were shot perpendicularly, and at 45°, at a distance of 10 m and 0.3 m, using full metal jacket (FMJ) projectiles (9 × 19 mm Luger). Simulants included ballistic gelatine at various concentrations, dental silicones with several degrees of hardness, alginates, latex, chamois leather, suture trainers for medical training purposes and various material compound models. In addition to complying to the general requirements for a synthetic simulant, results obtained from dental silicones shore hardness 70 (backed with 20 % by mass gelatine), were especially highly comparable to gunshot entry wounds in skin from real cases. Based on these results, particularly focusing on the macroscopically detectable criteria, we can strongly recommend dental silicone shore hardness 70 as a skin simulant for wound ballistics examinations. [ABSTRACT FROM AUTHOR]

Contact shots to the head often leave behind biological traces inside firearm barrels, a phenomenon of great forensic interest. Until now, the visualization and preservation of these traces presented a significant challenge, lacking a reliable method. This study addresses this gap by searching for a suitable method to extract the traces within a casting. Using alginate or gelatine as suitable materials, the results were hampered by serious adhesion issues and their extraction out of the firearm barrel was impeded. Finally, the combination of 11% gelatine with 1% alginate, introduced into the barrel around a 'central spine', succeeded to consistently produce replicable castings. Experimental contact shots displayed a distinct staining gradient from the muzzle to the rear of the barrel, as revealed through endoscopy and proved in the macroscopic casting. The technique proved effective for various common handgun barrels and successfully preserved blood and gunshot residue (GSR) patterns within the barrel. This method offers the dual benefits of visually mapping staining patterns and securing localized samples for targeted molecular genetic analysis in forensic investigations. [ABSTRACT FROM AUTHOR]

Although underwater submerged launching has been rigorously investigated for decades, there remains a dearth of comprehensive understanding regarding the underwater interior ballistic characteristics for varying barrel lengths. To address this knowledge gap, the present study aims to explore, via numerical simulations, the initial velocity of interior ballistics, projectile drag, and the mechanism of initial flow field formation at the muzzle under various barrel lengths, thereby considering the influence of differing barrel lengths. The five distinct lengths of barrels are expressed as dimensionless ratios of the weight of water column in front of the projectile to the weight of the projectile in order to be more general. Five different ratios of water-to-projectile weight are investigated: 1.0, 1.2, 1.5, 1.8, and 2.0, all possessing identical diameters and evaluated under equivalent launch conditions. Different ratios significantly impact muzzle velocity, with shorter barrels yielding higher muzzle velocities, while ensuring complete propellant combustion. Further investigations indicate that variations in drag constitute the fundamental cause of initial velocity changes. Furthermore, it is observed that barrels of different lengths exhibit identical characteristics at the point of maximum drag. The initial flow field at the muzzle exhibits considerable variations in terms of length, profile dimensions, and intensity. The findings of this study offer valuable insights into exploring the mechanism of submerged launching and will be utilized to investigate the optimal barrel length. [ABSTRACT FROM AUTHOR]

Highlights User expects his weapon to be light and reliable and to perform multiple times firing per unit time at the same time. In today's technology, the maximum number of firings can be made per unit time with steel barreled weapons, but in composite barrels; many problems occur due to overheating, strength and reliability. Meeting these opposite demands is an engineering problem. In this study, the design of a composite‐steel combination light gun barrel is studied. Firstly, pressure distribution through the barrel has been calculated using Vallier‐Heydenreich method. According to the calculations, analysis has been conducted using both steel barrel and composite barrel. After the analysis, a composite barrel has been manufactured and testing has been conducted on an all‐steel barrel and the manufactured composite barrel. Composite is carbon fiber and resin is epoxy resin. In composite material, carbon fiber is preferred at the rates of 50% and 60%, the material of the steel barrel is AISI 416R stainless steel. The manufactured steel barrels have the same outer diameter but different wall thickness ratios, firing tests were conducted in such a way that the number of shots per unit time was the same. Stress distribution within a gun barrel was calculated using Vallier‐Heydenreich method. Design and finite element analysis analysis for an all‐steel gun barrel and a composite gun barrel was conducted. A composite gun barrel was manufactured; by using composite materials, the barrel was lightened by 24.8%. The manufactured composite gun barrel and an all‐steel gun barrel were tested by firing over 2500 shots. [ABSTRACT FROM AUTHOR]

Stromboli is a volcanic island in a persistent state of activity, located off the northern coast of Sicily. The paroxysms have been the most powerful explosive phenomena at Stromboli in the last 150 years. These explosions can produce ballistic projectiles that can heavily affect trails and observation sites as well as hit inhabited areas at lower elevations, down to the coast. On July 3, 2019, a paroxysm significantly affected a great portion of the island with ballistic projectiles. In particular, many decimeter and meter-sized spatter bombs hit the W flank of Stromboli, and ignited multiple fires. In May 2022, we conducted an Unmanned Aerial System photogrammetric campaign over a sector of the W flank of Stromboli that was heavily affected by the paroxysm. The largest clasts were still preserved after 3 years, not disturbed by significant mass wasting phenomena or human interference, and they were not yet hidden by the post-fire regrowth of the brush vegetation. In this study, we constrained the main sources of uncertainty affecting the bombs distribution on the ground, by characterizing a percentage of uncertain clasts, testing various density estimators, and by modeling an areal buffer around the mapped clasts. We produced a 0.18 km2 wide 1.6-cm resolution orthomosaic, a 10-cm resolution Digital Surface Model, and 2813 outlines of the mapped ballistics. Spatial distribution of the ground cover and associated uncertainty were analyzed as a function of the distance and of the angular direction from the source. [ABSTRACT FROM AUTHOR]

A coupled framework of ballistic simulations and an optimized machine learning (ML) model was developed to accurately predict the kinetic energy reduction of a projectile impacting a target. ML models can require a significant number of data points for proper training, testing, and validation. High-performance computing (HPC) resources can be used to simulate the ballistic impacts of various projectiles against several different target materials using appropriate physics-based hydrocodes. Computational modeling can explore areas where experiments would naturally be cost-prohibitive. These hydrocodes can evaluate large parametric spaces varying the projectile and target variables that are required to train an ML model. In this study a large, generated set of data points was used to develop an optimized artificial neural network (ANN) algorithm to create a fast-running model without prior knowledge of the mathematical relationships between all the input and output variables. The optimized ANN model was developed using Optuna in an HPC environment to tune the hyperparameters needed for the ANN model. This fast-running ML model could then be leveraged to investigate designing optimized targets that could protect against different types of projectiles. The results of this work showed that the optimized ANN model predicted the kinetic energy reduction with a mean absolute percentage error of 2.7% across the validation data. Overall, the optimized ANN model showed excellent agreement across the range of data considered by the computational models. [ABSTRACT FROM AUTHOR]

The discovery of a specific form of Late Neolithic object in northeast Poland, commonly interpreted as reed arrowshaft straighteners, prompted investigation into the possible use of reed for archery in the European past. To examine the archery qualities of this raw material, and thus the likely rationale behind the manufacture and use of reed arrowshafts, a number of mechanical and experimental analyses were conducted. The results presented here indicate that reed was well suited for prehistoric archery. This is demonstrated above all by the arrowshaft stiffness required by this discipline, defined as the spine‐force, but also both the technological ease of production of arrows and their ballistic capabilities. [ABSTRACT FROM AUTHOR]

The object of research is the complex realm of energy localization and coherent ballistic electronic transport within low-dimensional silicon quantum wires, specifically those doped with germanium atoms. Unlike their three-dimensional counterparts, low-dimensional systems exhibit unique electronic transport behaviors, necessitating novel analytical approaches for a comprehensive understanding. The core of this investigation leverages the Phase Field Matching Theory (PMFT) and the tight-binding (TB) approximation, sophisticated methodologies that enable a deep dive into the quantum mechanical nuances of these systems. Through this lens, we examine the intricate dynamics of dispersion relationships, phase factors, group velocities, and notably, the impact of defects introduced by the germanium doping. This research meticulously analyzes how these defects affect electronic and thermal conductivities, along with densities of states, offering new insights into the role of Fano resonances in the fluctuation of transmission and reflection spectra. These resonances, we find, are crucially dependent on the nature of the defects, their configuration, and the electronic parameters in their vicinity, underscoring the nuanced interplay between material composition and electronic properties in low-dimensional systems. The implications of our findings extend far beyond the theoretical. They pave the way for significant advancements in nanotechnology and the design of electronic devices, highlighting the potential for creating more efficient, high-performance components. Furthermore, this work proposes a framework for developing non-destructive testing methodologies that could revolutionize material science by enabling the precise analysis of defects in low-dimensional systems without causing damage. This is particularly critical for the ongoing development of materials with optimized properties for various applications, from electronics to energy storage. In essence, this research not only enriches our understanding of the physics governing low-dimensional systems but also offers practical insights into leveraging these properties for technological innovation. By bridging the gap between theoretical physics and material science, our study sets the stage for the next generation of electronic components and non-destructive evaluation techniques, marking a significant step forward in the application of quantum mechanics to real-world challenges. [ABSTRACT FROM AUTHOR]

Computed tomography (CT) may have a crucial role in the forensic documentation and analysis of firearm injuries. The aim of this forensic ballistics case study was to explore whether two types of expanding bullets and a full metal-jacketed bullet could be differentiated by inspecting bullet fragments and fragmentation pattern in CT. Three types of.30 caliber bullets (full metal-jacketed Norma Jaktmatch, expanding full-copper Norma Ecostrike, and expanding soft-point Norma Oryx) were test fired from a distance of 5 m to blocks of 10% ballistic gelatine. CT scans of the blocks were obtained with clinical equipment and metal artifact reduction. Radiopaque fragments were identified and fragmentation parameters were obtained from the scans (total number of fragments, maximum diameter of the largest fragment, distance between entrance and the closest fragment, length of the fragment cloud, and maximum diameters of the fragment cloud). The fragmentation patterns were additionally visualized by means of 3D reconstruction. In CT, the bullet types differed in several fragmentation parameters. While the expanding full-copper bullet Ecostrike left behind only a single fragment near the end of the bullet channel, the soft-point Oryx had hundreds of fragments deposited throughout the channel. For both expanding bullets Ecostrike and Oryx, the fragments were clearly smaller than those left behind by the full metal-jacketed Jaktmatch. This was surprising as the full metal-jacketed bullet was expected to remain intact. The fragment cloud of Jaktmatch had similar mediolateral and superoinferior diameters to that of Oryx; however, fragments were deposited in the second half of the gelatine block, and not throughout the block. This case study provides a basis and potential methodology for further experiments. The findings are expected to benefit forensic practitioners with limited background information on gunshot injury cases, for example, those that involve several potential firearms or atypical gunshot wounds. The findings may prove beneficial for both human and wildlife forensics. [ABSTRACT FROM AUTHOR]

In examining deaths resulting from gunshot wounds, it is important to describe the wound pathway created by the projectile. Forensic pathologists must identify all entrance and exit wounds and account for all projectiles. Occasionally, confusion arises as to whether a skin defect represents an entrance wound or not, an exit wound, or some other type of wound. Herein, we propose the descriptor "bullet track skin defect" as a formal description for a superficial skin defect created along the pathway of a projectile within the body. Specifically, we define the "bullet track skin defect" as a partial‐ or full‐thickness skin defect produced by a projectile traveling beneath the skin in a relatively tangential fashion as part of a wound pathway within the body. It is somewhat analogous to a traditional graze or superficial tangential wound, wherein the projectile traveling outside the body strikes the skin tangentially from above, without entering the body. However, the projectile is already traveling within the body with the bullet track skin defect, disrupting the skin tangentially from below rather than from above, without exiting the body. Although these defects are not a common presentation of gunshot wounds, they are certainly not rare. With this case series, we suggest that such defects may be referred to as "bullet track skin defects." Alternative language that can substitute for "bullet track skin defects" includes "bullet track skin wounds" or "bullet track cutaneous defects." [ABSTRACT FROM AUTHOR]

We numerically investigate the spreading dynamics of wave packets in a one-dimensional lattice with quasiperiodic disorders and nonlinear interactions. Under moderate disorder strength, we reveal an intriguing super-ballistic diffusion driven by increasing the interaction strength from the ballistic diffusion in the non- and weakly interacting cases. We obtain a wide parameter region for such a faster-than-ballistic spreading of wave packets in the quasiperiodic lattice, although the nonlinear self-trapping is dominated under strong interactions. The super-ballistic diffusion is further analyzed based on the point source model. We also show the interaction-induced sub-diffusive spreading in the Anderson localized regime. The super-ballistic and sub-diffusive dynamics are exhibited in the spreading that starts from both the single-site and Gaussian wave packets. Our results showcase the interaction-enabled super-ballistic diffusion, which is scarce and experimentally realizable in artificial atomic or photonic lattices. • The super-ballistic diffusion induced by nonlinear interactions in a one-dimensional quasiperiodic lattice is revealed, which indicates the faster-than-ballistic spreading of wave packets. • A point source model is implemented to analyze the dynamic exponent and the physical picture of the super-ballistic diffusion. • The super-ballistic diffusion can be exhibited for single-site and Gaussian wave packets, which could be experimentally observed in artificial atomic or photonic lattices. [ABSTRACT FROM AUTHOR]

• Created the first ballistic dataset for enhanced cross-laminated timber (ECLT). • Compared partial and full penetration results utilizing eight known ballistic resistant materials. • Developed benefit-cost assessment of panel configurations. Cross-laminated timber (CLT), an engineered wood product, has grown in popularity in the United States over the last decade due to its ease of assembly, aesthetic appeal, and potential to serve as a sustainable and renewable alternative building material. The improved robustness of CLT over light-frame timber structures has increased its potential in force-protected infrastructure that must resist blast waves and ballistic projectile penetration, but softwood CLT is typically not sufficient to fulfill standard criteria for ballistic threats. To address these threats, enhanced CLT (ECLT) composite panels were manufactured with layers of various reinforcing materials (e.g., steel, FRP) placed between wood laminations. These panels were tested against various ballistic threats during two sets of laboratory tests in order to provide a basis for future research. The first set of testing subjected laboratory-produced Southern Yellow Pine (SYP) ECLT to 84 shots of 0.50-inch (1.27 cm) steel sphere projectiles to evaluate the performance of various reinforcing materials, layups, and fastening methods. A subsequent set of tests subjected commercially produced ECLT of steel-reinforced Spruce-Pine-Fir (South) (SPF-S) to 36 shots of NATO ammunition projectiles traveling at realistic, standard striking velocities. Except for a panel using four layers of a thin and finely woven steel hardware cloth, steel reinforcement was effective in stopping projectiles from all three types of NATO ammunition fired. Ultimately considering the results of these two sets of tests, an initial cost-benefit structure was developed and discussed to compare ECLT configurations holistically, a multi-material wood analytical model framework was established and compared to experimental results, and the first ballistic experimental database for ECLT was created. [ABSTRACT FROM AUTHOR]

This research continues the research of Deng et al. (2022) [1], using Discrete Element Method (DEM) coupled with Finite Element Analysis to solve shotgun exterior ballistics. The simulation examples in this research are using an Italian-made 24 gm #9½ birdshot with 433 pellets fired from 30" long, 12-gauge cylinder and full choke barrels. The simulations of shotgun exterior ballistics of this research included pellet swarm velocity and the pellet dispersion at different distances until 50 yards away from the muzzle. The ballistics simulation of the pellet swarm is completed from interior to exterior consecutively after the shotshell is fired inside the chamber so all ballistics performances can be calculated at one time. Three forces were applied to the pellets for exterior ballistics simulation: the contact force between pellets, the aerodynamic separation force between pellets, and the drag force. Because of the complexity of the aerodynamic forces exerted on pellets, this research used an equivalent aerodynamic force to simulate this complex phenomenon. Two birdshot models with different pellet formations were created; the first one was simulated to calibrate the separation scale factor defined in aerodynamic separation force, and the second one was used for validation and sensitivity of the model. The simulation results show that for #9½ birdshots fired by cylinder barrel, the average Effective Shot Dispersion (ESD) of pellet dispersion of both birdshots inside the 30" diameter of the target circle at 40 yards from the muzzle is 398.53, which is remarkably close to 396.98 of the experiment result. The simulation of the average pellets' target hit rate is 77.14% (inside the 30" diameter of the target circle), which is also remarkably close to the experiment hit rate of 77.57%. The same birdshot fired from a full choke barrel shows that ESD and hit rate rose to 406.34 and 83.14%, respectively. These results demonstrate the effectiveness of using the discrete element method in conjunction with the proposed equivalent aerodynamic force to predict the shotgun's interior and exterior ballistics. [Display omitted] • The equivalent aerodynamic forces were formulated from experiments of two pellets flying near to each other. • An Italian made 12-gauge 24 gm. #9½ birdshot with 433 pellets fired from 30-in long cylinder and full choke barrels were simulated. • Two birdshot models with different pellet formations were created to validate the sensitivity of the model. • Average simulated pellet dispersion at 40 yards fired by cylinder has only 0.43% error compared to the experiment. • Birdshot fired by full-choke barrel has 6.0% higher target hit rate compared to cylinder barrel did. [ABSTRACT FROM AUTHOR]

The use of ordnance gelatine has been widespread in the field of ballistics as a simulant for soft tissue when assessing ballistic threats. However, the traditional method of preparing ordnance gelatine is time-consuming and requires precision to ensure that the final mold meets the required specifications. Furthermore, temperature control is necessary post-production, and there are limitations on its usage duration. To address these issues, manufacturers have developed pre-mixed, gelatine-like products that are stable at room temperature and require less preparation time. Nonetheless, it is uncertain whether these new products can perform in the same manner as the gold standard of ordnance gelatine. This study used five types of blocks, including ordnance gelatine (10% and 20%), Clear Ballistics (10% and 20%) and Perma-Gel (10%) and subjected them to 9 mm, 0.380 Auto fired from a universal receiver and a 5.56 × 45 mm ammunition fired by a certified firearms instructor. Delta-V and total energy dissipation were measured after each test using data collected from ballistic chronographs placed in front of and behind each block. High-speed video was recorded, and a cut-down analysis conducted. The findings revealed variations in energy dissipation and fissure formation within the block, with greater energy based on fissure formation observed in the ordnance gelatine. Additionally, the high-speed video showed the occurrence of secondary combustions occurring in the premixed gelatines. [ABSTRACT FROM AUTHOR]

The last five decades have seen strong developments in irrigation modeling. In solid-set sprinkler irrigation, models have generally been applied to a few sprinklers in a regular arrangement, making them representative of a sector or a field. In this research, the Ador-Solid-Set model for whole-field solid-set sprinkler irrigation is presented, validated and applied to simulate an irrigation event in two fields: CA (10.2 ha) and ZA (24.5 ha), equipped with 12 and 26 sectors, respectively. The model couples pipeline hydraulics (EPANET), sprinkler ballistics and irrigation scheduling at execution time. Field experiments were used to validate the ballistic model in a solid-set combining full- and partial-circle sprinklers. Observed and simulated irrigation depths and coefficients of uniformity showed determination coefficients of 0.73*** and 0.89***, respectively. Optimization was used to estimate pipeline roughness based on pairs of pressure measurements (at the inlet and specific sprinklers): 26 pairs in CA and 58 pairs in ZA. Roughness parameters were estimated for the main pipeline, each sector and the sprinkler risers: 14 parameters in CA and 28 in ZA. More than a million hydraulic simulations were required to estimate roughness in each field. Maps were produced for applied water in CA and ZA following a sequential irrigation of their sectors lasting for 24 hours. The model produced whole-field coefficients of uniformity of 80.2 in CA and 80.9 in ZA. Finally, Ador-Solid-Set quantified the volume of drift outside the field (2.4 and 1.5% of the applied water in CA and ZA, respectively). This additional drift can be added to the wind drift and evaporation losses obtained from empirical equations, in a process that requires further analysis. Research efforts are also needed to enhance the current model capabilities and address the challenges related to water quantity and quality in sprinkler solid-sets. • A solid-set irrigation model has been presented, calibrated and validated. • The model has been applied to two solid-sets of 10.2 and 24.5 ha. • New thresholds may be required for whole-field Irrigation uniformity. • The model quantified drift outside the computational domain. [ABSTRACT FROM AUTHOR]

Polyurea (PU) elastomers have become increasingly popular in recent years due to their exceptional blast mitigation, ballistic protection, and wear resistance properties. However, their applications as protective materials are often limited as a result of their high flammability. In this study, aromatic dianhydrides (ArDAs) were employed to capture the thermal decomposing products of PU during combustion and facilitate the generation of highly heat-resistant aromatic polyimides (i.e., end group capturing effect), thus enhancing the material's char-forming ability and improving its flame retardancy. The ArDAs were found to significantly reduce the peak heat release rate (PHRR), total heat release (THR), total smoke release (TSR), and total CO release (TCO) of PU, and meanwhile increased the amount of char residue. At 20 wt% content of 3,3′,4,4′-benzophenonetetracarboxylic dianhydride (BTDA), PHRR, THR, TSR and TCO of PU were reduced by 70.6%, 32.5%, 44.7% and 58.8%, respectively, the char residue was increased by 405%, and the mechanical properties of PU were well maintained (88.5% tensile strength and 91.0% elongation at break of pure PU). These findings demonstrate that ArDAs could serve as a new kind of halogen/phosphorus-free flame retardant for PU elastomers. [Display omitted] • Novel halogen/phosphorus-free flame retardants were designed for PU elastomers. • The flame retardant mechanism is end group capturing by aromatic dianhydrides (ArDAs). • PHRR, THR, TSR and TCO were simultaneously reduced, and char residue was improved. • Both excellent flame retardant property and high mechanical property were achieved. [ABSTRACT FROM AUTHOR]

The first goal of this work is to find a regression law for PVC (Polyvinyl Chloride) coupled to hydrogen peroxide on a 10-N-scale hybrid thruster, which appears to be suitable for small satellites when, for example, manoeuvres are required for orbital control purposes. Different techniques were initially analysed in order to reconstruct the ballistics inside the combustion chamber, starting from the experimental data. Subsequently, even if the different techniques lead to similar results, the one that takes into consideration the greatest number of the experimental measurements was chosen for the post-processing, and three different regression curves were obtained according to various criteria. The resulting regression laws coming from the selected method appear to be in agreement with the experimental results and constitute a powerful means for designing engines with this fuel. Finally, a performance analysis has been performed and in-space thrust and specific impulse have been estimated. PVC shows excellent performance and can be a good candidate for this type of applications, on a par with other more popular polymeric materials. [ABSTRACT FROM AUTHOR]

The ongoing pursuit of space and hypersonic flight continues to expose critical gaps in the understanding of material behavior under hypervelocity impact (HVI) and hypersonic flow conditions. Such limitations pose serious risks for aerospace vehicles, spacecraft, hardened structures, defensive systems, etc. Consequently, the development of materials and systems that can endure HVIs and hypersonic flight is a major obstacle in the quest for sustainable space exploration, reusable air-breathing hypersonic vehicles, and enduring protective structures. HVIs (≥ 3.0 km/s) can induce severe material deformation, erosion, fracturing, fragmentation, melting, vaporization, and sublimation. At the same time, hypersonic (≥ Mach 5) vehicles may be subjected to intense thermal and mechanical loads. Addressing these grand challenges requires a multifaceted and interdisciplinary approach, combining well-designed experiments with physics-based analytical and numerical modeling. Studying material behavior under HVIs and hypersonic conditions has been facilitated by two-stage light gas gun (2SLGG) aeroballistic ranges for almost seven decades. This current study surveys over 90 2SLGG aeroballistic ranges operational since 1990 to assess global launch and experimental capabilities. The 2SLGG's origins and research applications are explored, highlighting its significance in various fields, including shock physics, planetary science/defense, military defense, nuclear physics, hypersonic vehicle survivability and performance, and spacecraft micro-meteoroid/orbital debris protection. A summary of relevant HVI phenomena is presented to underscore the importance of 2SLGGs and to elucidate similarities and differences among various 2SLGG aeroballistic ranges and their supporting methods/tools. The 2SLGG's working principles are explained, and configurations and operations are compared. Modifications resulting in "three-stage light gas guns" are briefly mentioned for completeness. The full range of current 2SLGG performance capabilities is assessed with impact kinetic energies ranging from ∼ 10 joules to nearly 100 megajoules, and the facility survey results are used to explain the variations in aeroballistic range tankage, experiment types, research applications, and diagnostic systems. Finally, an overview of 2SLGG performance prediction methods is provided, featuring notable empirical, analytical, and numerical approaches. • Survey of over 90 2SLGG aeroballistic ranges active since 1990 worldwide. • 2SLGG's impact in multiple fields like military and space highlighted. • Detailed 2SLGG working principles and three-stage gun modifications explained. • 2SLGG performance spectrum from 10 J to 100 MJ detailed. • Variability in 2SLGG ranges and their scientific uses described. [ABSTRACT FROM AUTHOR]

Boron carbide, with a nominal stoichiometry of B 4 C, is a highly desired ceramic candidate for armor applications due to its high hardness derived from the complex crystal structure. However, stress-induced local amorphization can lead to failure and is a known challenge for this material which must be addressed for applications in ballistic environments. Understanding boron carbide's atomic structural behavior and bonding environment is critical in determining effective strategies to mitigate these issues. In this work, the thermo-structural behavior of B 4 C has been studied in detail using a conical nozzle levitator system coupled with in-situ synchrotron X-ray diffraction. Lattice expansion and the resulting thermal expansion coefficients (CTEs) were determined from 25-2100 °C. Rietveld refinements showed anisotropic atomic displacement for each of the 4 unique sites as a function of temperature. An exceptionally large z-axis displacement for the boron chain center is linked to bond weakness and may be linked to fa α 11 ster expansion of the α 33 relative to CTEs. Thermally induced lattice changes can inform the use of boron carbide at elevated temperatures as well as help develop strategies for mitigating structural failure for armor applications. [Display omitted] [ABSTRACT FROM AUTHOR]