Search

A mathematical simulation of the internal ballistics of a shot from a gun, depending on the design of the charge of the gun, has been performed. A general system of equations defining the unsteady movement of a two-phase gas–powder mixture in the channel of the barrel of a gun in the one-dimensional approximation is presented. Results of simulation of a shot from a gun charged with tubular powder or chopped powder are presented. The influence of the gradual ignition of a powder in a gun and of its nonstationary and erosion burning in it on the parameters of the ballistic process in the gun and the influence of the mass and disposition of an igniter in the gun on the dynamics of a shot from it were investigated. [ABSTRACT FROM AUTHOR]

The sodium rhodizonate test is a simple colorimetric technique used to identify traces of lead and barium. A positive test provides rapid and photographically documentable results for shots fired at distances not exceeding 50 cm. Usually, this method is not used for identification of the firing hand, which is detected by electron microscopy with energy dispersive analysis (SEM-EDX), requiring the removal of any particles on the surface to be analyzed by STUB. The use of Sodium Rhodizonate, which is undoubtedly less selective, has the disadvantage of target element solubilization (lead and barium) and thus the loss of the preliminary morphological investigation of the particles. The purpose of this paper is to demonstrate that the two indicated methods can be considered complementary in the following order: 1. buffer sampling for electron microscopy investigation (STUB); 2. and subsequent performance of the Sodium Rhodizonate Test. In some special cases, when it is necessary to obtain the result more quickly, with regards to respecting the chronology of the aforementioned tests, it may be useful to carry out the Sodium Rhodizonate Test first, especially when particular and perhaps antiquated weapons were used for suicidal purposes causing considerable gas dispersion and shot residues from the mechanisms. This research illustrates how significant results were obtained substantiating the suicide hypothesis, following the use of an old revolver (year of manufacture around 1915-1920). [ABSTRACT FROM AUTHOR]

The wounding potential of a projectile depends on its kinetic energy. The aim of the study was to investigate the deceleration of non-deforming full metal jacket handgun bullets (FMJ) in gelatine blocks of increasing length. The temporary cavity (TC) was visualized using a SA-X2 Photron camera. 126 test shots in 9 mm nominal calibre were fired under strict temperature control conditions (4°C) at small gelatine blocks ranging from 2 to 12 cm in length. The deposited energy was calculated based on the loss of bullet velocity through high-speed video analysis. The length of the TC was measured, when the TC reached its maximum height. The volume of the TC was approximated by a cylinder. Regression analysis showed a linear correlation between the length of the bullet path and the energy transfer. The constant deceleration of the FMJ bullets in gelatine up to 12 cm bullet path was confirmed across various brands and velocity ranges (270–450 m/s). Higher impact velocities correlated with increased loss of energy in the target medium. The shape of the bullet tip influenced the characteristic of deceleration. The volume of the tubular temporary cavity, derived from high-speed video records, was found to be proportional to the energy transferred. The proposed approach might be a valuable tool in advancing wound ballistics research. • Deceleration of FMJ bullets proportional to bullet path in compact target models. • Higher impact velocities resulted in greater loss of energy in the target medium. • The shape of the bullet tip influenced the characteristic of deceleration. • Proportionality of the temporary cavity to the transferred energy. [ABSTRACT FROM AUTHOR]

This paper presents a numerical and an analytical approach for calculation of internal ballistics parameters through determination of thermal and gasdynamic characteristics. The calculated parameters are validated through experimental tests on a real weapon system. The internal ballistic calculations are provided for two types of propellants using an analytical and a numerical model. Calculations and tests are performed for an anti-material rifle 12.7 mm. Weapon and ammunition testing is carried out according to the permanent international commission standard. Theoretical and experimental results for the gunpowder gases pressure and the muzzle velocity are compared. The good agreements between the calculated and the measured pressures and velocities increase the reliability of the estimated gunpowder gas temperatures in the barrel. The obtained results enable analysis and comparison of the output internal ballistics parameters for different types of propellant applications. [ABSTRACT FROM AUTHOR]

• Thermal modification does not significantly change the ballistic performance of coastal western hemlock CLT. • Density and hardness do no fully encompass the energy absorbing capacity of CLT under small arms ballistic threats. • Empirically fit UFC partial penetration equation formulations fit treatment specific datasets with minimal error. • One global UFC partial penetration equation can be utilized for design with an appropriate safety factor. To test and understand the potential for integration of thermally modified coastal western hemlock CLT systems in military applications, 109 ballistic experiments were conducted at the United States Army Engineer Research Development Center's Fragmentation Simulation Facility. For a range of CLT thicknesses, the depth of penetration and residual velocities were recorded for different striking velocities utilizing a 0.50 caliber steel sphere projectile. This information was used to compare and add to the existing ballistics data for CLT, investigate the effects of thermal modification on high strain rate loading of wood, assess physics-based empirical design equations used by the Unified Facilities Criteria, and evaluate energy absorbing behavior at a range of thicknesses and striking velocities. The experimental results showed that thermal modification does not significantly alter the full and partial penetration performance of coastal western hemlock CLT. However, the mechanism of fracture along the path of the projectile differed, which indicates that the model parameters used in the UFC design equation (density, hardness, and projectile properties) may not fully encompass the ballistic failure mechanisms of CLT. [ABSTRACT FROM AUTHOR]

The insufficient recognition of injuries by the BB-gun (regarded as toys for children) has led to its increasing misuse without permission, which has caused many public safety issues. Aiming to enhance the understanding of the injuries by the BB-gun, the experimental and numerical study of BB-Gun pellet penetrating "cowhide + gelatine" composite target was comprehensively carried out. It was confirmed from the experiment that BB-Gun is capable of inflicting severe or fatal wounds to important organs, and perforating the skin or not could be employed to evaluate the safety of BB-guns. Moreover, three forms of ballistic limit (including: velocity, kinetic energy and specific kinetic energy) of typical BB were calculated and analyzed by reasonably validated numerical simulation method. Additionally, a formulation was acquired by dimensional analysis based on the simulation results and was verified to accurately predict the ballistic limit velocity of BB with different mechanical properties. The method may help to improve the understanding on the minimal velocity needed to perforate skin and may be advised as the determination of the safety of BB-gun. [ABSTRACT FROM AUTHOR]

In this paper, the effect of the chemical composition of .22LR bullets was studied and correlated to the extent and quality of the markings left after shooting them with the same gun. Scanning electron microscopy and optical comparator microscopy equipped with 3D and profilometry modules were used as non destructive techniques with two main purposes. The first is to assist the firearm examiner in the choice of the ammunition most suitable for preparing the test bullets. The second is to propose an approach, crossing data from optical microscopy, profilometry and space-resolved chemical analysis, for explaining the morphology of striae, whether continuous or interrupted. Among the most notable results is the finding that commercial .22LR ammunition show very wide interbrand, interlot and intralot variability. A selection of test ammunition solely based on the same brand and model used on the crime scene is therefore not suitable, urging the need for a more accurate choice, based on a preliminary chemical analysis. [ABSTRACT FROM AUTHOR]

Population reduction or eradication of domestic or non-domestic species may be required to address their impacts on the environment, other species, or human interests. Firearms are often used to accomplish these practical management objectives, and there is increased concern that the methods used may compromise animal welfare. We document the accuracy and humaneness of gunshot placement to the brain and cervical vertebrae of Philippine deer (Rusa marianna) on Guam during depopulation activities as a model for meeting AVMA standards of euthanasia under field conditions (e.g., animal is not in hand). Deer were shot with a .223 caliber rifle from 10–125 m and approached immediately (<20 s) for assessment. A subset of adult deer was further evaluated for physiological responses including cessation of heart rate, respiration, ocular reflexes, and post-mortem spasms. All deer shot in the brain (n = 132) and upper cervical spine (C1—C3; n = 18) died immediately due to the destruction of the brain or spinal tissue. Shot placements were all within 1.9 cm of the point of aim (i.e., the center of the target region). The accuracy and immediate insensibility resulting from targeting of C1—C3 demonstrates that this is an alternative target site when animal positioning is not optimal for targeting the brain, or there is a need to preserve brain tissue (e.g., Chronic Wasting Disease testing). While targeting of C4 –C7 vertebrae (n = 6) was accurate and resulted in immediate incapacitation, the failure to produce immediate insensibility does not support the use of this shot placement when upper cervical or brain shot placement is an option. It is reasonable to achieve sufficient accuracy to target the brain or upper cervical vertebrae of deer under field conditions and meet standards of euthanasia while accomplishing management objectives. [ABSTRACT FROM AUTHOR]

Synthetic models, also called "surrogates", are commonly used in wound ballistics in order to simulate human tissues. Despite several surrogates are worldwide accepted and used; some of them have not been yet fully validated and their limits for forensic reconstructions have not been deeply investigated yet. In this work we present a homicide/suicide case involving three gunshots to the head with bullets retained in the skull or beneath the scalp. Reconstruction of these cases was performed preparing three individual synthetic head models based on post-mortem computed tomography (PMCT) measurements. Ballistic soap, polyurethane plates and 10% ballistic gelatine at 4°C were used as simulants in individually adapted thickness. Ballistic tests were performed using the questioned firearm and ammunition type. The damages on the synthetic models have been compared to the findings in PMCT and autopsy of the victims. Although the results highlighted general similarities in terms of injury characteristics, some of the experimental shots overpenetrated. Furthermore, the bullets recovered in the synthetic models did not show the same quality of deformations as the questioned bullets. This lack of bullet deformation in the synthetic models might be mainly attributed to the physical difference between real bones and polyurethane surrogate. [ABSTRACT FROM AUTHOR]

Gun violence is a global phenomenon with regional variation in frequency and severity. Handguns are often used in violent deaths such as suicides and homicides. Hence, ballistic trauma is a critical subject of forensic investigations. Trauma patterns are fundamental evidence for the reconstruction of the incident and for the determination of the manner of death. This study investigated the differences in trauma patterns with a series of experiments using six different calibers (.22 LR, .38 Special, .380 ACP, 9×19mm, .40 S&W, and .45 ACP) and four different bullet types. Synbone® spheres (polyurethane bone proxies) were used for close range 30cm simulated executions. The polyurethane spheres constitute an excellent proxy for human crania at the macroscopic level as suggested by other studies. The results showed that the radius of the entrance wound is positively correlated (Pearson's correlation coefficient R=0.846, p<0.05) with the caliber dimension. As muzzle velocity increased, endocranial beveling increased. Bullet weight, conversely, does not seem to have an effect on the size of the endocranial beveling present in Synbone® spheres. The ballistic experiments exhibited similarities in entrance wound morphology; radial and concentric fracture patterns, hydraulic burst effect, circumferential delamination, and endocranial beveling with that of documented forensic cases with corresponding caliber shot. Synbone spheres seem appropriate for ballistic simulations of cranial injuries; yet, more research is needed to verify these observations. [ABSTRACT FROM AUTHOR]

A ballistic model-based method, which builds upon previous work by Lo and Ferguson [J. Acoust. Soc. Am. 132, 2997-3017 (2012)], is described for ranging small arms fire using a single acoustic sensor node collocated with the target, without a priori knowledge of the muzzle speed and ballistic constant of the bullet except that they belong to a known two-dimensional parameter space. The method requires measurements of the differential time of arrival and differential angle of arrival of the muzzle blast and ballistic shock wave at the sensor node. Its performance is evaluated using both simulated and real data. [ABSTRACT FROM AUTHOR]

Gun violence continues to be a staggering and seemingly intractable issue in many communities. The prevalence of gun violence among the sub-population of individuals under court-ordered community supervision provides an opportunity for intervention using remote monitoring technology. Existing monitoring systems rely heavily on location-based monitoring methods, which have incomplete geographic coverage and do not provide information on illegal firearm use. This paper presents the first results demonstrating the feasibility of using wearable inertial sensors to recognize wrist movements and other signals corresponding to firearm usage. Data were collected from accelerometers worn on the wrists of subjects shooting a number of different firearms, conducting routine daily activities, and participating in activities and tasks that could be potentially confused with firearm discharges. A training sample was used to construct a combined detector and classifier for individual gunshots, which achieved a classification accuracy of 99.4 percent when tested against a hold-out sample of observations. These results suggest the feasibility of using inexpensive wearable sensors to detect firearm discharges. [ABSTRACT FROM AUTHOR]

This article describes a negative effect of size tolerance on the trigger characteristic. The trigger characteristic is the dependence of trigger force and trigger angle. An invalid trigger characteristic affects the accuracy of shooting and can be changed by not only proper choice of dimensions, but also the location of individual components. The paper shows an example of trigger mechanism that is designed as a Glock type mechanism. The solution for designers of small arms authors suggested the use of software MW. [ABSTRACT FROM AUTHOR]

The article deals with the ballistic analysis of pistol cartridge of calibre 9 mm Luger. As a basis of the analysis the standard cartridge with 8 g FMJ projectile was chosen. The aim of the analysis is to assess the effect of projectile mass change on basic ballistic characteristic of weapon-cartridge system during development of new types of projectiles. There is also explained possible utilisation of the obtained results with use of selected typical small arms cartridge in the end of the article. [ABSTRACT FROM AUTHOR]

The article describes the method of determination of limit velocity for the aluminium alloy sheet metal from the airplane fuselage skin hit by a pistol projectile of calibre 9 mm with utilisation of 2D FEM model of interaction between the projectile and the sheet metal. The simulations are based on accomplished firing experiments and results are compared. The results of simulation can be utilised for prediction of level of damage of aircraft fuselage in case of firing on board of the plane. [ABSTRACT FROM AUTHOR]

• Small and medium arms fire can be stopped with a snow-based protective structure. • Snow-filled commercial gabions can be efficiently constructed. • Structures can be construction at a rate of about 0.5 hr/m3 with common equipment. • Snow set-up time of 24 h is recommended. • All but one model of projectile penetration in snow matched our results within 32%. Small (5.56 mm, 7.62 mm and 9 mm) and medium (12.7 mm) arms rounds were fired at snow-filled 1.5m cubic gabions in a mid-winter condition in Fairbanks, Alaska. The rounds were excavated and penetration by each ammunition type was measured. A distribution and average of penetration depth was determined. All 320 rounds fired were captured within 1.5m after entering the snow barrier. Comparison with published models of ballistics penetration of snow showed mixed results with several matching our data within 10% and all but one within 32%. However, most of these models are simplistic in that they accommodate limited variables and therefore may not be expected to perform well in all settings. We conclude that snow-based ballistics protection structures can be quickly and efficiently erected in suitable environments and with minimal size, can provide reliable protection against small and medium arms fire. [ABSTRACT FROM AUTHOR]

Evaluation of cartridge cases is essential within forensic ballistic analysis and is used in an attempt to establish a connection to the weapon used to fire it. This study consists of two experiments. The aims of Experiment 1 were to establish whether micro-CT is appropriate and repeatable for ballistic cartridge case analysis and if measurements can be extracted repeatably and reliably. Experiment 2 aimed to compare cartridge cases from two weapons to establish the magnitude of variation within and between weapons. A total of 48 cartridge cases fired by two distinct weapons were collected and micro-CT scanned to a high resolution. One randomly selected cartridge was scanned ten times under the same conditions to ensure repeatability of the scanning conditions in Experiment 1. Three novel measurements to quantitatively assess the firing pin impressions were proposed in Experiment 1 and comparatively analysed from two weapons in Experiment 2. Experiment 1 showed that micro-CT is an effective and highly repeatable and reliable method for 3-dimensional imaging and measurement of ballistic cartridge cases. Furthermore, high agreement for inter-rater reliability was found between five raters. Quantitative micro-CT analysis of the firing pin impression measurements in Experiment 2 showed a significant difference between the two studied weapons using Welch's t-test (p < 0.01). This study shows the advantage and reliability of utilising micro-CT for firing pin impression analysis. Quantitation of the firing pin impression allows distinction between the weapons studied. With expansion to further weapons, application of this methodology could complement current analysis techniques through classification models. [ABSTRACT FROM AUTHOR]

Abstract: For competitors in the shooting sports, gun recoil can affect performance and create discomfort. An objective method of measuring felt recoil forces would be useful to evaluate methods of recoil reduction. An experimental test apparatus was developed to measure recoil forces of sporting rifles and shotguns. No modifications to the firearms themselves were necessary to make the measurements. Through both inertial and dissipative restraint mechanisms, the apparatus reproduced gun movement that was representative of that experienced by a particular shooter. This should result in measured recoil forces similar to those experienced by the shooter. The apparatus measures the horizontal shoulder force and the vertical force component exerted at the stock comb. The recoil event was found to be quite short, having duration on the order of 10ms. Peak recoil forces for common shotgun target loads were in the range of 1.6–2.2kN (360–494lbf). The apparatus was found sensitive enough to measure recoil force differences among different factory loaded ammunition, and differences in recoil force imparted by different firearms shooting the same ammunition. The apparatus should prove useful for quantifying differences in felt recoil as affected by ammunition type, gunstock geometry, barrel porting, recoil reduction devices, and gun weight, among other factors. [Copyright &y& Elsevier]

The main motivation of this work is to clarify whether the hopes of significantly improving the performance of the conventional guns by using plasma ignition have a realistic basis. We assessed the possibility of improving the whole interior ballistic process, its repeatability and safety, through a uniform propellant ignition. In addition, we planed to improve the gun performance [the projectile muzzle energy (velocity)] by "forcing" "cold" charges to perform as "hot" ones (achieving "temperature compensation"). All of these goals are intended to be accomplished by using reasonable electrical energies (which would allow the reduction of the mass and volume of the power supply). We also avoided any significant changes in the conventional gun topography in order to prevent unacceptable costs. The presented research program proved that by using a standard 105-mm gun (concerning its barrel length and charge chamber volume) and a standard propellant, improved performances (more than 28% in the projectile muzzle energy) can be achieved while dense charges are used. In addition, significant reduction of the important effect, the "temperature gradient," is obtained. The capacity of plasma as the ignition factor to provide ballistic gain has also been demonstrated. [ABSTRACT FROM AUTHOR]

Abstract: Greenhill''s Rule for estimating rifling twist in artillery and small arms is interesting both because of its simplicity and longevity. This article describes (a) Greenhill''s Simplified Rule for estimating the twist of rifling; (b) describes his original, more complete, but much less known Rule; (c) summarizes how he got the Rule; and (d) relates it to the modern stability factor. Some comments about twist, bullet stability, and black powder velocities are presented. [Copyright &y& Elsevier]

This paper is based upon the observation that, when a bullet is fired, it creates characteristic markings on the cartridge case and projectile. From these markings, over 30 different features can be distinguished, which, in combination, produce a ‘fingerprint’ for a firearm. By analyzing features within such a set of firearm fingerprints, it will be possible to identify not only the type and model of a firearm, but also each and every individual weapon just as effectively as human fingerprint identification. A new analytic system based on the fast Fourier transform for identifying projectile specimens by the line-scan imaging technique is proposed in this paper. This paper develops optical, photonic, and mechanical techniques to map the topography of the surfaces of forensic projectiles for the purpose of identification. Experiments discussed in this paper are performed on images acquired from 16 various weapons. Experimental results show that the proposed system can be used for firearm identification efficiently and precisely through digitizing and analyzing the fired projectiles specimens. [ABSTRACT FROM AUTHOR]

Presents information on a study which examined long-range ballistics to highlight the launch parameters of importance to electromagnetic gun designers. Atmospheric effects; Launcher energy limitations; Subcaliber projectiles; Conclusions.

Focuses on a study that presented comparisons between high and low density cases for a number of ballistic parameters. Overview of the approach used to increase kinetic energy in the electrothermal-chemical guns in the United States; Description of gun system; Sensitivity to parameter changes; Conclusions.

Bullet ricochet off a surface in a shooting scene occurs in diverse conditions and affected by array of factors. Therefore ricochet analysis of a particular incident demands case by case analysis supported by the knowledge of existing subject knowledge and empirical testing. In this view, existing empirical test results on bullet ricochet experiments have become always assisted and referred by investigators during scene reconstruction and in Courts. This forensic based research was aimed to understand the ricochet behaviour and related aspects of Kalashnikov bullets (7.62mm×39mm) on 1mm sheet metal. 1mm sheet metal was selected as the target surface of the study, based on its greater possibility of existing in concurrent urban environments as vehicle bodies, electrical appliances, road signs, boundary walls, partitions, walls of mobile houses etc. The research added brand new knowledge to the firearm investigation field in general and specifically to AK shooting investigations and scene reconstruction. The ricochet angles and critical angle of 1mm sheet metal and AK bullets, relationship of different impact feathers and angle of incidences are some of the main findings of the research. The double head impact mark which produces as a result of bullet's interaction with the target and it's specific relationships with the incident angles is the other most important results of the research which has not reported so far in a bullet ricochet study. In addition to the contribution of knowledge to the field of forensic sciences in general and forensic ballistic in particular, this research further emphasises the need for case by case empirical study to understand the ricochet behaviour of different bullet and target combinations. On the other hand, this study very deeply convinced firearms investigators on the risk of applying general bullet ricochet theory on yielding and nonyielding surfaces to reconstruct all bullet ricochet incidents which would result in wrong interpretations, critical errors in shooting scene reconstruction and finally for false testimonies. [ABSTRACT FROM AUTHOR]