Search

• Pulp and paper mill sludge (PPMS) landfill sites have GHG assessment challenges. • GHG fluxes measured by chambers with (F +) and without (F-) a frame were compared. • Flux relationships up to 80 % were shown between F- and F + chambers (the standard) • Correction factors for F- chambers were built to estimate fluxes from F + chambers. • The approach can refine GHG inventories on PPMS landfill sites. Assessments of greenhouse gas (GHG) emissions in managed areas are facing various challenges. A non-flow-through, non-steady-state (NFT-NSS) chamber coupled to a frame permanently inserted into the landfilled substrates is a standard method for quantifying GHG emissions in managed areas, such as pulp and paper mill sludge (PPMS) landfill sites. Frequent measurements are needed to minimize uncertainties on GHG emission factors at the landfill site scale. However, maintaining a frame inserted into the substrates for a long time period is often impossible due to landfilling management operations. Therefore, GHG measurements using NFT-NSS chambers placed directly on substrates' surface could be an interesting option. Our objectives were to determine the relationships between CO 2 , CH 4 , and N 2 O fluxes measured with (F +) and without (F-) a frame inserted in the substrates' surface and to develop correction factors for fluxes measured without a frame. Measurements were made at different PPMS landfill sites in the province of Québec, Canada. Stronger GHG flux relationships were observed at the provincial (across sites) than the specific site scale: the variance in GHG fluxes from F- chambers explained up to 80 % of variance in fluxes from F + chambers. The measured CO 2 , CH 4 , and N 2 O fluxes in F- chambers were on average 53, 78, and 63 % lower, respectively, than those estimated by the models at provincial scale. The correction factors developed with this approach could greatly extend the number of sites where in situ GHG measurements can be done and would help refining GHG inventories at the provincial and national levels. [ABSTRACT FROM AUTHOR]

Background: Health care systems contribute significantly to greenhouse gas emissions. One source of these emissions is single-use products. Examination table paper does not confer protection against microbial contamination and thus can be omitted while following infection control standards. The objective is to eliminate the routine use of examination table paper in outpatient oncology clinics at BC Cancer. Methods: A quality improvement approach was used. Examination tables continued to be disinfected using wipes between patients, but table paper was not used. Plan-do-studyact cycles were performed at four regional cancer centres. Results: Pre-intervention, the cancer centres used 19 to 69 rolls of paper monthly. Postintervention, usage declined to 0 to 2 rolls monthly. This was associated with annual cost savings of $3974 and a reduction of 32 501 kg of carbon dioxide emissions. Conclusions: The use of examination table paper can be eliminated in outpatient clinics, resulting in both cost savings and a reduction in carbon dioxide emissions. [ABSTRACT FROM AUTHOR]

The present study examines the assumptions, modeling structure, and results of DICE-2023, the revised Dynamic Integrated Model of Climate and the Economy (DICE), updated to 2023. The revision contains major changes in the treatment of risk, the carbon and climate modules, the treatment of nonindustrial greenhouse gases, discount rates, as well as updates on all the major components. Noteworthy changes are a significant reduction in the target for the optimal (cost-beneficial) temperature path, a lower cost of reaching the 2 °C target, an analysis of the impact of the Paris Accord, and a major increase in the estimated social cost of carbon. [ABSTRACT FROM AUTHOR]

Furthermore, very complicated multiphase and thermal processes are the corner stone in modern industry, high technology development, energy conversion and utilization, renewable and sustainable energy technologies, just to name a few here. Therefore, it is essential to develop new technology to improve energy utilization efficient, sustainable energy and low carbon/zero carbon technology to reduce carbon footprint. [Extracted from the article]

Chemical upcycling of plastic waste from landfills to value-added products offers both economic and environmental benefits. Reported here is a simple method to convert high-density polyethylene (HDPE) into upcycled waxes in a very high yield (up to 93%). This selectivity is achieved by reducing the degradation temperature of HDPE via the addition of an inexpensive and reusable sodium chloride. These upcycled waxes had performance comparable to those of commercial rheology modifiers. In addition, kraft paper coated with these upcycled waxes exhibited excellent water- and oil resistance. A preliminary revenue analysis showed that this innovation allows plastic-to-wax to conversion with a three-fold revenue benefit over traditional ways of producing pyrolysis waxes from plastics. Also, sodium chloride reduces the pyrolysis temperature, thus reducing energy consumption and greenhouse gas emissions, supporting cleaner production, a circular economy, and generating less environmental pollution. The underlying concept reported herein can be extended to major plastics by reducing the degradation temperatures of plastics, thereby obtaining even better control over the pyrolysis products. Thus, these findings have the potential to enhance the circular economy of plastics and protect our environment from plastic waste. SYNOPSIS. Chemical upcycling of post-consumer polyethylene via a sodium chloride-catalyzed process. [Display omitted] • Demonstrated table salt-assisted pyrolysis of high-density polyethylene. • Converted polyethylene into upcycled waxes at mild temperatures and in high-yield. • Used upcycled waxes as rheology modifiers and water-proof coating material. • Performed preliminary revenue analysis. [ABSTRACT FROM AUTHOR]

Waste paper disposed in landfills notably contributes to greenhouse gas (GHG) emissions and impedes more sustainable, circular alternatives, such as recycling. In Hong Kong, this unsustainable approach is currently dominant as 68% of waste paper products are treated in landfills in 2020. To contextualize the impact of local waste paper management and explore mitigation potentials of circular alternatives, this paper develops a quantitative assessment framework around GHG emissions development trajectories. Combining guidelines of the Intergovernmental Panel on Climate Change (IPCC), national GHG inventories, and local parameters from life cycle analysis, five GHG emissions projections were simulated along the Shared Socioeconomic Pathways (SSPs) until 2060. Most recent baselines indicate that Hong Kong's current waste paper treatment generated 638,360 tons CO 2 -eq in 2020, comprising 1,821,040 tons CO 2 -eq from landfill and 671,320 tons CO 2 -eq from recycling, and −1,854,000 tons CO 2 -eq from primary material replacement. Proceeding along a Business-as-Usual scenario under SSP5, GHG emissions will dramatically increase to a net 1,072,270 tons CO 2 -eq by 2060, whereas a recycling-intensive scenario will lead to a net saving of −4,323,190 tons CO 2 -eq. To complement the quantitative evidence on the benefits of waste paper recycling, field research was conducted to explore the feasibility of circular policy innovation from the perspective of recycling stakeholders. These empirical qualitative and quantitative findings from stakeholders' business routines and material transactions provide crucial indications for policy and institutional innovation: Essentially, for Hong Kong to improve waste paper recycling capacities and facilitate a circular economy (CE), local stakeholders require support via fiscal policy measures (financial subsidies or tax reductions) and infrastructure improvements (delivery access and material storage). In sum, this study employs a novel analytical framework combining original qualitative and quantitative evidence to provide policy innovation towards circular, GHG emission-saving waste paper management. [Display omitted] • A new framework assessing greenhouse gas emissions from waste paper treatment. • Exploring long-term carbon neutrality pathways for managing waste paper. • Using empirical evidence from recycling stakeholders for circular policy innovation. [ABSTRACT FROM AUTHOR]

• Advancements in sludge processing to reduce particle and acidification emissions. • Reduced environmental footprint through innovative sludge treatment. • Sludge hydrochar carbon stabilization contributes to climate change mitigation. Proper management of wastewater treatment plant side streams in pulp and paper mills is a matter of great interest. This study evaluates the environmental impact of different strategies in the management of biosludge from pulp and paper mills in Finland through a Life Cycle Assessment methodology. The base industrial standard practice, biosludge incineration for energy recovery and ash landfill disposal (Scenario 1), was compared to the alternative process of hydrothermal carbonization. The hydrochar generated from hydrothermal carbonization was evaluated for energy recovery through incineration (Scenario 2), or for use in composting for nutrient recovery (Scenario 3). The results showed that the hydrothermal process improved the overall environmental performance of the sludge management, particularly in terms of energy consumption and greenhouse gas emissions. The use of hydrochar as a soil amendment in composting also resulted in a significant reduction on the environmental impact compared to the other two scenarios. Overall, this study highlights the potential of hydrothermal carbonization and hydrochar utilization as sustainable options for managing biosludge from pulp mills. [ABSTRACT FROM AUTHOR]

China is the top emitter of greenhouse gases in the world. Pulp and paper industry is one of eight the strictly regulated industries about carbon emission in China. However, estimates of carbon emissions from China's pulp and paper industry have been suffered from remarkable uncertainty. It is summarized that is aroused by the inaccuracy of factors evaluating energy consumption, and the huge gap between the calculation standards for assessing energy consumption in the production process and the actual level recorded in the factories. This paper re-evaluated the carbon emission of China's pulp and paper industry from the perspective of life cycle assessment, and applied more accurate emission factors, taking account of the actual energy consumption of the production process in factories, to estimate the actual carbon emissions in maximum. It is found that the national standards about the energy consumption quota of China's pulp and paper industry is no longer applicable, and the actual energy consumption regulated in the production process is far better than the advanced level given by the national standards. The greenhouse gas emission have been seriously overestimated approximately 12.00%–56.17% by international organizations. • Life Cycle Analysis of the China's pulp and paper Industry is conducted thoroughly. • The pulp flow of China's pulp and paper Industry is analyzed. • Energy regulated in factory is far better than the national standards' required. • Carbon emissions of China's pulp and paper Industry are overestimated. [ABSTRACT FROM AUTHOR]

Variable renewable energy-based power is expected to increase toward a sustainable society, although the power cannot be dispatched effectively due to its intermittent nature. To accelerate renewable energy implementation, we simulated energy flows of paper mills installing wind energy and evaluated their potentials to function as energy hubs for appropriate early-stage design. We targeted 39 Japanese paper mills assumed to have thermal energy storage, wind–thermal energy converters and regional woody biomass installed, and analyzed the amount of power and heat selling and life cycle greenhouse gas emissions. The results for the paper mills were compared with conventional mills to examine effective conditions for greenhouse gas reduction. The amount of power or heat selling depended on the capacity of the paper mill and the installed equipment. Most paper mills could reduce greenhouse gas using thermal energy storage, wind energy, and woody biomass. The paper mill with the highest life cycle greenhouse gas reduction, compared with conventional mills, could achieve a 190% reduction. To function as a cogeneration energy hub, the equipment installed in paper mills should be designed according to the conditions of the paper mills and their regions. • Paper mills have potential as energy hubs by integrating variable renewable energy. • Thermal energy storage and wind–thermal energy converters were studied. • Energy flows and greenhouse gas emissions of paper mills were simulated. • Most mills could provide stable power and/or heat supplies and reduce emissions. [ABSTRACT FROM AUTHOR]

China's rapid urbanization has led to the development of integrated transport networks, which requires the transport sector to pay particular attention to the integrated transport comprehensive carrying capacity (ITCCC). Concurrently, global climate change has focused the world community's attention on greenhouse gas concentrations like CO2. This study establishes an ITCCC measurement model of urban agglomerations (UAs) and measures the comprehensive carrying capacity from four factors: socio-economic, basic resources, transport facilities, and traffic environment. In particular, this paper takes carbon emission as a critical indicator of the traffic environment when considering the impact factors of ITCCC. Based on the data of China's five major UAs, this study estimates carrying capacity levels with the ITCCC model and analyses regional characteristics using the spatial-temporal differentiation method. The results show that the traffic environment significantly impacts the ITCCC. Further low-carbon transport policies and measures are recommended to achieve sustainable development of integrated transport in UAs. [ABSTRACT FROM AUTHOR]

• RCF wastes brick achieves 24% lower thermal properties than the control brick. • RCF wastes brick requires 10% lower firing temperature than the control brick. • Utilizing as-received waste materials requires zero grinding energy, benefiting manufacturers and cutting emissions. • Lower firing temperature saved $158,460 by cutting 417 tonnes of CO 2. Building materials drive the global economy, yet face severe environmental hurdles: resource depletion, greenhouse gas emissions, and waste generation. In order to mitigate the impact from these challenges, authorities seek sustainable and eco-friendly alternatives as an urgent need. This study focuses on the utilization of as-received rejected contaminated fines (RCF) obtained from the yellow bins' waste (paper) recycling process, in brick production. Diverse tests assessed the brick performance, including compressive strength, absorption rate, thermal conductivity, 3D CT scanning for morphological analysis, and durability analysis. Additionally, a leachate analysis was performed to evaluate the environmental implications. Economic benefits, particularly the reduction of CO 2 emissions, were also evaluated. The findings confirmed that as-received waste can be utilized for fired clay brick production without the need for pulverization. The novel brick product made with as-received RCF waste exhibited superior thermal characteristics (up to a 31.25 % reduction compared to control bricks) while meeting the essential compliance requirements outlined by national standards. Moreover, each firing cycle led to a potential value of up to USD 158,460 through a reduction of 417 tonnes of CO 2 , resulting from a 9.5 % reduction in firing temperature (1000 °C). The results from this study offer valuable insights into the potential of using RCF waste as a sustainable alternative in the brick manufacturing industry. This alternative could address the soaring demand in the current market, resolve the escalating solid waste crisis, and mitigate clay shortages, while providing a sustainable solution for the brick industry. [ABSTRACT FROM AUTHOR]

Summary: Despite major improvements in recycling over the last decades, the pulp and paper sector is a significant contributor to global greenhouse gas emissions and other environmental pressures. Further reduction of virgin material requirements and environmental impacts requires a detailed understanding of the global material flows in paper production and consumption. This study constructs a Sankey diagram of global material flows in the paper life cycle, from primary inputs to end‐of‐life waste treatment, based on a review of publicly available data. It then analyzes potential improvements in material flows and discusses recycling and material efficiency metrics. The article argues that the use of the collection rate as a recycling metric does not directly stimulate avoidance of virgin inputs and associated impacts. An alternative metric compares paper for recycling (recovered paper) with total fibrous inputs and indicates that the current rate is at just over half of the technical potential. Material efficiency metrics are found to be more useful if they relate to the reuse potential of wastes. The material balance developed in this research provides a solid basis for further study of global sustainable production and consumption of paper. The conclusions on recycling and efficiency should be considered for improving environmental assessment and stimulating a shift toward resource efficiency and the circular economy. [ABSTRACT FROM AUTHOR]

Life Cycle Assessment (LCA) is a well-established and informative method of understanding the environmental impacts of consumer products across the entire value chain. However, companies committed to sustainability are interested in more methods that examine their products and activities' impacts. Methods that build on LCA strengths and illuminate other connected but less understood facets, related to social and economic impacts, would provide greater value to decision-makers. This study is a LCA that calculates the potential impacts associated with Bounty ® paper towels from two facilities with different production lines, an older one (Albany, Georgia) representing established technology and the other (Box Elder, Utah), a newer state-of-the-art platform. This is unique in that it includes use of Industrial Process Systems Assessment (IPSA), new electricity and pulp data, modeled in open source software, and is the basis for the development of new integrated sustainability metrics (published separately). The new metrics can guide supply chain and manufacturing enhancements, and product design related to environmental protection and resource sustainability. Results of the LCA indicate Box Elder had improvements on environmental impact scores related to air emission indicators, except for particulate matter. Albany had lower water use impacts. After normalization of the results, fossil fuel depletion is the most critical environmental indicator. Pulp production, electricity, and fuels for product production drive fossil fuel depletion. Climate change, land occupation, and particulate matter are also relevant. Greenhouse gas (GHG) emissions by pulp, electricity, papermaking, and landfill methane from the disposed product, drive climate change impacts. Pulp provides significant offsets to balance climate change impacts due to sequestration of atmospheric carbon dioxide. Ninety-nine percent of land occupation is for the growth of the trees for pulp production. Papermaking, electricity, and pulp production cause the most potential particular matter formation. [ABSTRACT FROM AUTHOR]

The low-carbon supply chain is one of the predominant topics towards a green economy and it establishes the opportunity to reduce carbon emissions across the product value chain. This paper focuses on recycling and optimized sourcing in the paper industry as a case company. The main objective is to engage the case company with their supplier networks to diminish the greenhouse gases (GHG) emissions and cost in their production process. It proposes a model to support the selection of the best green supplier and an allocation of order among the potential suppliers. The proposed model contains a two-phase hybrid approach. The first phase presents the rating and selection of potential suppliers by considering economics (cost), operational factors (quality and delivery), and environmental criteria (recycle capability and GHG emission control) using Fuzzy Technique for Order of Preference by Similarity to Ideal Solution (Fuzzy TOPSIS) methodology. The second phase presents the order allocation process using multi-objective linear programming in order to minimize cost, material rejection, late delivery, recycle waste and $$\mathrm{CO}_{2}$$ emissions in the production process. A case study from a paper manufacturing industry is presented to elucidate the effectiveness of the proposed model. The results demonstrate a 26.2 % reduction of carbon emission by using recycle products in the production process. The firm benefits by forming a systematic methodology for green supplier evaluation and order allocation. Finally, a conclusion and a suggested direction of future research are introduced. [ABSTRACT FROM AUTHOR]

Blue hydrogen (H 2) serves as a pivotal initial step towards emissions reduction and a seamless transition to green hydrogen by providing a cleaner alternative to grey hydrogen. Blue H 2 can be obtained through diverse pathways (i.e. , distinct processes and stages) within the hydrogen supply network (HSN), resulting in varying greenhouse gas emission levels. This paper uses the Life Cycle Assessment methodology to compare 18 different blue HSN pathways. Blue hydrogen is produced from three different processes (i.e. , Steam Methane Reforming (SMR), Partial Oxidation of Methane (POM), and Auto-Thermal Reforming (ATR)) that are coupled with carbon capture unit (CCU). Moreover, it can be conditioned to different states or carriers (i.e. , liquefied H 2 , compressed H 2 , ammonia, and methanol), stored using various methods, transported by different means according to its state, and reconditioned to its original state at end-users. The LCA results indicate that the NH 3 pathway has the least environmental impact measuring just 2.12 kgCO 2equ / kgH 2 compared to the other 18 blue HSN pathways. This pathway involves producing hydrogen from ATR process coupled with CCS, and eventually delivering as ammonia to consumers. Additionally, the blue H 2 results of this paper are compared to the green H 2 results discussed in the previous paper. The comparison highlights that integrating renewable energy in the form concentrated photovoltaic collectors produces the lowest emissions compared to all pathways. It reduces the emissions from 45.3% to 67% depending on the pathways, compared to the ATR process coupled with CCU. • SMR, POM, or ATR with carbon capture for blue hydrogen production. • This LCA study compares 18 blue HSN pathways for their environmental performance. • Different pathways within the HSN lead to various levels of GHG emissions. • NH 3 path emits the least emissions (2.12 kgCO 2equ /kgH 2) among blue H 2 paths. • CH 2 path emits the least emissions (0.080 kgCO 2equ /kWh) among all paths. [ABSTRACT FROM AUTHOR]

The paper reviews and evaluates a 30-year-long atmospheric CO2 data series measured at the Hegyhátsál tall-tower greenhouse gas monitoring site, a member of the World Meteorological Organization (WMO) Global Atmosphere Watch (GAW), US National Oceanic and Atmospheric Administration (NOAA), and pan-European Integrated Carbon Observation System (ICOS) networks. The paper also gives the technical description of the monitoring system and its changes over time and introduces the environment of the station. This low-elevation (248 m above mean sea level – m a.m.s.l.), mid-continental central European site shows a 3.90 ± 0.83 µmolmol-1 offset relative to the latitudinally representative marine boundary layer reference concentration, presumably due to European net anthropogenic emissions. The long-term trend (2.20 µmolmol-1yr-1) closely follows the global tendencies. In the concentration growth rate, the ENSO effect is clearly detectable with a 6–7-month lag time. The summer diurnal concentration amplitude is slightly decreasing due to the faster-than-average increase in the nighttime concentrations, which is related to the warming climate. The warming climate also caused a 0.96 ± 0.41 dyr-1 advance at the beginning of the summer CO2 -deficit season in the first half of the measurement period, which did not continue later. The summer CO2 -deficit season was extended by 9.0 ± 6.1 d during the measurement period. [ABSTRACT FROM AUTHOR]

The pursuit of climate action to meet net-zero targets has triggered the call for a global energy transition from fossil fuels to clean energy sources. However, this global energy transition does not entirely recognise all countries' social, economic and technological capacities as well as emission contributions as envisaged under the Common but Differentiated Responsibilities (CBDR) principle, which underlies international climate policy. It is concerned more with the outcome of transitioning to clean energy than with justice in the transition process. Recognition justice, an element of energy justice, enables us to identify the inequalities that global energy paradigms (such as the energy transition) can create and how a justice framework can help us understand the implications of energy injustice and address the inequities across energy systems. Recognition justice acknowledges the divergent perspectives rooted in social, economic and racial differences and the varied strengths of developed and developing countries. The energy transition process ought to recognise these differences so that they are reasonably expected to benefit everyone. Implementing the energy transition in the Global South (GS) in the same way as it is being advanced in the Global North will have security, justice, economic, resource-stranding, and sustainable development implications. This issue (of injustice in the energy transition) is aggravated by two dichotomous realities: many countries in the South will be most impacted by climatic changes, yet there remains political and social opposition to climate action through the energy transition. As a solution, this paper relies on the notion of recognition justice with support from the Rawlsian justice concept to argue that a delayed transition represents justice and recognises the peculiar nature and different circumstances of the GS. It identifies that learnings from the Kigali Amendment to the Montreal Protocol on Substances that Deplete the Ozone Layer and the notion of CBDR under international climate treaties can be mainstreamed into energy transition research and policies to achieve justice for countries of the GS. The paper further finds that a delayed transition for the GS will (i) enable the region to address sustainability-related issues of hunger and multidimensional poverty, essential to realising other Sustainable Development Goals, whilst gradually implementing energy transition policies; (ii) present an attractive case against political and social opposition to energy transition in the GS; (iii) advance the goal of CBDR already recognised under international climate treaties and the bifurcated approaches established in such treaties; and, finally, (iv) ensure that developed countries contributing the most to greenhouse gas emissions take the lead now and act while the GS effectuates national contributions sustainably. [ABSTRACT FROM AUTHOR]

This document is a compilation of research papers that explore the topics of Smart Cities and Positive Energy Districts (PEDs). The papers cover a range of subjects including energy efficiency, renewable energy communities, smart urban management, and financial schemes for sustainable neighborhoods. The findings emphasize the importance of energy renovation, potential energy and financial savings, and the need for collaborative approaches and policy direction to achieve sustainable urban development. The papers also provide insights into innovative solutions and technological advancements that can contribute to the realization of carbon-neutral and sustainable cities. This document serves as a valuable resource for library patrons conducting research on energy efficiency and sustainable building practices. [Extracted from the article]

The research on automatic monitoring methods for greenhouse gases and hazardous gas emissions is currently a focal point in the fields of environmental science and climatology. Until 2023, the amount of greenhouse gases emitted by the livestock sector accounts for about 11–17% of total global emissions, with enteric fermentation in ruminants being the main source of the gases. With the escalating problem of global climate change, accurate and effective monitoring of gas emissions has become a top priority. Presently, the determination of gas emission indices relies on specialized instrumentation such as breathing chambers, greenfeed systems, methane laser detectors, etc., each characterized by distinct principles, applicability, and accuracy levels. This paper first explains the mechanisms and effects of gas production by ruminant production systems, focusing on the monitoring methods, principles, advantages, and disadvantages of monitoring gas concentrations, and a summary of existing methods reveals their shortcomings, such as limited applicability, low accuracy, and high cost. In response to the current challenges in the field of equipment for monitoring greenhouse and hazardous gas emissions from ruminant production systems, this paper outlines future perspectives with the aim of developing more efficient, user-friendly, and cost-effective monitoring instruments. [ABSTRACT FROM AUTHOR]

The global energy system is in transition. It is attempting to reach net‐zero greenhouse gas emissions by 2050. The systemic changes mean that the role of bioenergy will change. The potential of bioenergy to make a flexible contribution to the energy system is key for the achievement of global emission reduction ambitions and the functioning of the low‐carbon energy system and economy. As the volume of sustainably available biomass resources is limited, defining the contributions from bioenergy to a low‐carbon energy system and finding balances – and ideally synergies – between the different possible energy and climate system services that biomass can provide will be very important. The recognized system services include, among others, the flexible operation of bioenergy plants to integrate variable renewable energy sources and to provide negative carbon dioxide (CO2) emissions. Interest in flexible operation of bioenergy value chains, bioenergy with carbon capture and utilization as well as synergies with renewable hydrogen‐based value chains has increased recently. The objective of this paper is to present a holistic definition of flexible bioenergy as a system service based on the work conducted in International Energy Agency (IEA) Bioenergy Technology Collaboration Programme's Task 44 Flexible Bioenergy and System Integration, and to provide some practical examples. The paper also presents the different bioenergy system services and considers their definitions and interactions, as this is important in energy system design. The definition of flexible bioenergy shows that the flexibility provision from bioenergy goes far beyond the traditional definition of providing short‐term flexibility in the power sector. Indicators to demonstrate the value of services as well as further quantitative assessment of synergies and trade‐offs are needed to valorize the different services from bioenergy and create viable business cases. [ABSTRACT FROM AUTHOR]

The pulp and paper industry, which provides cellulose pulp and paper, bio-based energy and chemicals, is one of the largest energy consumers, greenhouse gases (GHG) and pollutant emitters among manufacturing industries. Although the environmental impact of the pulp and paper industry has been extensively studied, life cycle assessment (LCA) results have not yet reached a consensus. By means of a systematic review and meta-analysis, this article contributes to the quantification and harmonization of the life cycle environmental impacts of pulp making and paper making systems. Based on the screening of 45 cases of paper making and 18 cases of pulp making, we found that 1 t of paper results in about 950 kg carbon dioxide (CO 2 ) equivalent (CO 2 -eq) GHG emissions on average. However, there are distinct differences between countries and pulp and paper categories. The dominant factor influencing GHG emissions is energy use. In paper making, the pulp making process is responsible for 62% of energy use, 45% of GHG emissions, 48% of acidification potential, and 49% of eutrophication potential. The kg CO 2 -eq emissions of three different types of pulp were as follows: Kraft, 508 kg CO 2 -eq/t; chemi-mechanical, 513 kg CO 2 -eq/t; and recycled pulp, 408 kg CO 2 -eq/t. Excluding emissions from electricity and steam production, the convergence of carbon emissions is observed within the same categories of pulp. Straw-based pulp caused far more environmental impact than any other type because of the intensive inputs in agricultural activities as well as in the pulp making process. This research highlighted the inconsistencies in functional units, system boundaries, and methodologies and carbon neutrality assumptions in different LCA studies of pulp and paper making. Future studies should focus on the environmental impact of straw-based pulp making, system boundary unification, and calculation of biogenic carbon emissions. [ABSTRACT FROM AUTHOR]

The global cement industry produces over four billion tonnes annually. In recent years, the quest for increasing energy efficiency has led this industry to test and use “waste” materials as alternative fuels (AF). The objective of this study was to examine the use, as alternative fuel, of the shredded non-recycled plastics and paper residue (NRPP) of a materials recovery facility at the Balcones plant in San Antonio, Texas; this material has a Lower Heating Value (LHV) of about 17 MJ/kg and is called “engineered fuel” (EF). The results showed that EF consists of mostly paper fiber, a biogenic material, so its use helps to decrease CO 2 emissions from cement production. In the US, on an average about 4.3 MJ of thermal energy are used to dry, decompose, and sinter the carbonate minerals to produce one kg of “clinker” that is then ground to cement powder and mixed with other compounds. If the maximum amount of EF that can be used by the U.S. cement industry (83 million tonnes of cement per year) were to be separated at Material Recovery Facilities and used as alternative fuel in cement kilns, the diversion of non-recycled paper and plastics from landfills would amount to 17.7 million tonnes of EF. The general methodology used for the Life Cycle Assessment (LCA) is Eco-indicators 99 that uses the SimaPro database and four scenarios were assessed. The corresponding chemical structure of the EF was calculated and the associated emissions during combustion were determined. The laboratory analyses determined the average makeup of the sampled fuels consisted of 20% fossil based carbon and 80% biogenic. The use of EF in the cement industry reduces greenhouse gas emission by up to 3 tonnes of CO 2 per tonne of EF used in place of a high-quality coal. The study also found that use of EF in cement production has no adverse effect on the stack emissions of cement plants, nor on the quality of cement produced. The mercury concentration in the stack gas of U.S. cement kilns is well below the U.S. standard and the total dioxin emissions of all cement plants amount to only 0.05% of the dioxins emitted by all U.S. sources. Furthermore, the cement process incorporates the residual ash in the EF into the final clinker, thus resulting in both energy and materials recovery. [ABSTRACT FROM AUTHOR]

Greenhouse gas (GHG) emissions of the Quebec pulp and paper industry fell by more than 30 percent from 1990 to 2006. We use an energy demand model to analyze the contributions to this decrease of energy prices, product mix, technological change, and biomass use. The product mix is made of pulp, and cardboard, and paper. Pulp is an intermediate product for the industry, but not necessarily so for mills; vertical integration varies across mills and presents different opportunities to transfer heat between stages of production. Chemical and mechanical pulping processes are used to form two groups of pulp and paper mills. We find that changes of product mixes contributed the most to reduce GHG emissions, followed to a lesser extent by increases of fuel prices relative to electricity. The estimated electricity and fuel price elasticities are low. However it is still possible to significantly reduce GHG emissions by substituting natural gas for heavy fuel oil; such a substitution could be brought about by a small change of their relative price. [ABSTRACT FROM AUTHOR]

Abstract: Upflow anaerobic sludge blanket (UASB) reactor was installed to replace the conventional anaerobic lagoon treating bagasse wash wastewater from agro-based pulp and paper mill, to generate bio-energy and to reduce greenhouse gas emissions. The plant was designed to treat 12MLd−1 of wastewater having two 5ML capacity reactors, 5.75kgCODm−3 d−1 organic loading rate and 20h hydraulic retention time. In the plant 80–85% COD reduction was achieved with biogas production factor of 520Lkg−1 COD reduced. In 11 months 4.4 millionm3 of biogas was generated from bagasse wash wastewater utilizing UASB process. Utilization of the biogas in the Lime Kiln saved 2.14ML of furnace oil in 9 months. Besides significant economic benefits, furnace oil saving reduced 6.4GgCO2 emission from fossil fuel and conversion of the anaerobic lagoon into anaerobic reactor reduced 2.1Gg methane emission which is equal to 43.8Gg of CO2. [Copyright &y& Elsevier]

Due to the huge amounts of wastewater discharge and the high pollution loads in papermaking industry, many greenhouse gases (GHG) are emitted in the papermaking wastewater treatment process. The wastewater dissolved oxygen (DO) control has been considered as the most cost-effective control solution for GHG reduction in wastewater treatment plants (WWTP). However, the competition between contaminant removal efficiency and GHG reduction hinders the drastic reduction of GHG emissions from WWTP. In this study, based on the established integrated GHG emission model, explicitly considering the total GHG reduction targets on the premise of effluent compliance, an intelligent control scheme has been developed for an activated sludge process in a paper mill. Regarding DO as the controlled variable, the proposed hierarchical optimal proportional-integral (HOPI) control scheme was established consisting of three layers: 1) Layer 1 for the effluent quality estimation, 2) Layer 2 for the optimal DO set point determined by genetic algorithm with the influent variations to obey discharging norms and reduce GHG emissions, 3) Layer 3 for the DO tracking proportional integral (PI) control with the controller parameters adjusted by the back propagation neural network to track the dynamically optimized DO set points. The simulation results showed that, compared with the open-loop (OL) operation (averaged aeration, 10/h), the proposed HOPI control (averaged aeration, 7.9/h) reduced the GHG emissions by 12.54% under the premise of discharging norms, which was mainly attributed to the reduction of the aeration electricity consumption. In contrast, the PI control (averaged aeration, 12.9/h) increased the GHG emissions by 7.48% compared with the OL operation. Thus, the proposed HOPI control strategy has demonstrated potential for the application of GHG reduction in industrial WWTPs. [ABSTRACT FROM AUTHOR]

Due to the huge amounts of wastewater discharge and the high pollution loads in papermaking industry, many greenhouse gases (GHG) are emitted in the papermaking wastewater treatment process. The wastewater dissolved oxygen (DO) control has been considered as the most cost-effective control solution for GHG reduction in wastewater treatment plants (WWTP). However, the competition between contaminant removal efficiency and GHG reduction hinders the drastic reduction of GHG emissions from WWTP. In this study, based on the established integrated GHG emission model, explicitly considering the total GHG reduction targets on the premise of effluent compliance, an intelligent control scheme has been developed for an activated sludge process in a paper mill. Regarding DO as the controlled variable, the proposed hierarchical optimal proportional-integral (HOPI) control scheme was established consisting of three layers: 1) Layer 1 for the effluent quality estimation, 2) Layer 2 for the optimal DO set point determined by genetic algorithm with the influent variations to obey discharging norms and reduce GHG emissions, 3) Layer 3 for the DO tracking proportional integral (PI) control with the controller parameters adjusted by the back propagation neural network to track the dynamically optimized DO set points. The simulation results showed that, compared with the open-loop (OL) operation (averaged aeration, 10/h), the proposed HOPI control (averaged aeration, 7.9/h) reduced the GHG emissions by 12.54% under the premise of discharging norms, which was mainly attributed to the reduction of the aeration electricity consumption. In contrast, the PI control (averaged aeration, 12.9/h) increased the GHG emissions by 7.48% compared with the OL operation. Thus, the proposed HOPI control strategy has demonstrated potential for the application of GHG reduction in industrial WWTPs. [ABSTRACT FROM AUTHOR]

Land-use change in the boreal forest region leads to agriculture to be carried out on acid, shallow and low fertility soils. To correct soil fertility and promote crop productivity, manure and inorganic fertilizers are added, increasing the risk for greenhouse gas emissions (GHGE). To reduce the reliance on synthetic soil amendments while taking advantage of locally relevant industrial by-products, wood ash (WA) and paper sludge (SL) have been proposed as soil amendments for a range of soil types. We posited that amending soils with WA , SL and biochar will improve soil health parameters and fertility of boreal soils. Microbial activity resulting to nitrogen losses and availability were assessed. WA had a stronger ameliorative effect on acid boreal soils compared to SL. Both WA and SL increased soil microbial biomass and basal respiration resulting in higher net mineralization and thus significant increases in CO 2 emissions. Co-application of urea with WA or SL further increased net mineralization compared to when used independently. Conversely, the biochar's effect was short-lived and not significant. Nevertheless, addition of biochar was shown to reduce CO 2 emissions in all cases except in WA amended soils. No significant differences were observed in CH 4 emissions across all treatments. WA and SL may improve soil fertility and quality but could also contribute significantly to GHG emissions in acid boreal soils. Further research is recommended to assess the mitigating effect of various biochar feedstocks on GHG emissions when co-applied with WA and SL. • The effect of wood ash and paper sludge on acid soils was tested in incubation tests. • Both increased the soil microbial biomass, respiration, and net mineralization. • Greenhouse gas emissions were larger for paper sludge amended soils. • Supplementing biochar to wood ash increased soil CO 2 fluxes. • Supplementing biochar to paper sludge or limestone ash reduced soil CO 2 fluxes. [ABSTRACT FROM AUTHOR]

Simple Summary: Dairy farming is a significant source of pollutant gas emissions, contributing to climate change and air quality degradation. Understanding these emissions in milk production promotes productive efficiency and sustainable resource use. The aim of this paper is to provide a comprehensive analysis of ammonia and greenhouse gas emissions in dairy farming, utilizing bibliometric analysis methods. Articles featuring experimental data collection were selected, exclusively in English. The databases considered were Scopus and Web of Science. The analyses were conducted using Bibliometrix version 4.0.0 and VOSviewer version 1.6.20 tools to create knowledge maps visualizing information on research countries, institutions, author collaborations, and keyword networks. The search yielded 187 articles related to major pollutant gases such as methane, ammonia, carbon dioxide, nitrous oxide, and hydrogen sulfide. This study provided valuable insights into gas emission sources, air quality, environmental sustainability, and animal welfare, as well as identifying gaps and critical points in research on the topic. Ammonia and greenhouse gas emissions in dairy farming are crucial for climate change mitigation and sustainable agriculture. This research can contribute to academic interests while enhancing agricultural practices and informing environmental policies. The relevance of this research will persist with the growing demand for sustainable practices, as more researchers and organizations recognize the importance of gas emissions and mitigation research. A deeper understanding of gas emissions in milk production is crucial for promoting productive efficiency, sustainable resource use, and animal welfare. This paper aims to analyze ammonia and greenhouse gas emissions in dairy farming using bibliometric methods. A total of 187 English-language articles with experimental data from the Scopus and Web of Science databases (January 1987 to April 2024) were reviewed. Publications notably increased from 1997, with the highest number of papers published in 2022. Research mainly focuses on ammonia and methane emissions, including quantification, volatilization, and mitigation strategies. Other gases like carbon dioxide, nitrous oxide, and hydrogen sulfide were also studied. Key institutions include the University of California–Davis and Aarhus University. Bibliometric analysis revealed research evolution, identifying trends, gaps, and future research opportunities. This bibliometric analysis offers insights into emissions, air quality, sustainability, and animal welfare in dairy farming, highlighting areas for innovative mitigation strategies to enhance production sustainability. This research contributes to academia, enhancing agricultural practices, and informing environmental policies. It is possible to conclude that this research is a valuable tool for understanding the evolution of research on gas emissions in dairy cattle facilities, providing guidance for future studies and interventions to promote more sustainable production. [ABSTRACT FROM AUTHOR]

Vehicle electrification has shown the potential to reduce environmental impacts and greenhouse gas emissions from the transport sector. As electric vehicles (EVs) become increasingly prominent, the efficient placement of charging infrastructure poses a complex challenge that demands careful consideration. This paper delves into the investigation of how travel and parking patterns, derived from empirical data on freight vehicles, influence the optimal distribution of charging infrastructure across the freight network. This paper presents a node-based approach to optimize the allocation of charging infrastructure tailored explicitly for freight transport. The study identifies optimal locations for operator-owned charging infrastructure by leveraging GPS-based data collected from a fleet of freight vehicles operating in the greater Gothenburg metropolitan area. This research aims to enhance our understanding of the charging infrastructure requirements inherent in the freight transport system and provide decision support to logistics companies contemplating the shift from conventional fossil fuel vehicles to electric freight vehicles. The proposed model holds the potential for seamless adaptation to diverse freight transport systems, offering valuable insights to expedite the transition toward fossil-free freight transport on a broader scale. • Complexity in charging infrastructure placement for freight transport. • Empirical data from a fleet of freight vehicles in Gothenburg metropolitan area. • Investigation of travel and parking patterns of freight vehicles. • Node-based optimization approach to allocate charging infrastructure. [ABSTRACT FROM AUTHOR]

Key long-lived greenhouse gases (CO2, CH4, and N2O) are perhaps among the best-studied components of the Earth's atmosphere today; however, attempts to predict or explain trends or even shorter-term variations of these trace gases are not always successful. Infrared spectroscopy is a recognized technique for the ground-based long-term monitoring of the gaseous composition of the atmosphere. The current paper is focused on the analysis of new data on CO2, CH4, and N2O total columns (TCs) retrieved from high resolution IR solar spectra acquired during 2009–2022 at the NDACC atmospheric monitoring station of St. Petersburg State University (STP station, 59.88°N, 29.83°E, 20 m asl.). The paper provides information on the FTIR system (Fourier-transform infrared) installed at the STP station, and an overview of techniques used for the CO2, CH4, and N2O retrievals. Trends of key greenhouse gases and their confidence levels were evaluated using an original approach which combines the Lomb–Scargle method with the cross-validation and bootstrapping techniques. As a result, the following fourteen-year (2009–2022) trends of TCs have been revealed: (0.56 ± 0.01) % yr−1 for CO2; (0.46 ± 0.02) % yr−1 for CH4; (0.28 ± 0.01) % yr−1 for N2O. A comparison with trends based on the EMAC numerical modeling data was carried out. The trends of greenhouse gases observed at the STP site are consistent with the results of the in situ monitoring performed at the same geographical location, and with the independent estimates of the global volume mixing ratio growth rates obtained by the GAW network and the NOAA Global Monitoring Laboratory. There is reasonable agreement between the CH4 and N2O TC trends for 2009–2019, which have been derived from FTIR measurements at three locations: the STP site, Izaña Observatory and the University of Toronto Atmospheric Observatory. [ABSTRACT FROM AUTHOR]

This paper presents a method for designing low carbon bio-based building materials, also named bio-concretes, produced with wood wastes in shavings form (WS) and cementitious pastes. As the aggregates phase of bio-concretes is composed of plant-based particles, known as porous and high water-absorbing materials, the bio-concretes cannot be designed by using the traditional design rules used for conventional mortar or concrete. Then, the method used in the current paper is an adaptation of a previous one that has been developed in a recent paper where bio-concretes were produced with a cement matrix, three types of bio-aggregates, and a proposal of a design abacus. However, when that abacus is used for designing WBC with low cement content in the matrix, the target compressive strength is not reached. In the present paper, the method is extended to low cement content matrix (up to 70% of cement substitution) and also considering the greenhouse gas (GHG) emission of the WBC. To obtain data for proposing a new design abacus, an experimental program was carried out by producing nine workable WBCs, varying wood volumetric fractions (40–45–50%), and water-to-binder ratios. The bio-concretes produced presented adequate consistency, lightness (density between 715 and 1207 kg/m3), and compressive strength ranging from 0.64 to 12.27 MPa. In addition, the GHG emissions of the WBC were analysed through the Life Cycle Assessment methodology. From the relationships obtained between density, compressive strength, water-to-binder ratio, cement consumption, and GHG emissions of the WBC, calibration constants were proposed for developing the updated and more complete abacus regarding an integrated mix design methodology. [ABSTRACT FROM AUTHOR]

Simple Summary: The United Nations' goals for sustainability, like Zero Hunger by 2030, urge us to find new ways to produce food without harming nature. As traditional resources for feed, like soymeal and fishmeal, become scarcer and more expensive, exploring alternative protein sources is one options. Research on using insect meal instead of fishmeal shows promise in terms of animal growth and feed efficiency. This paper assesses the socio-economic benefits and costs of production of insect meal to substitute fishmeal in feed, while also focusing on factors that would affect performance most. The study evaluates the economic value of insect-based products, waste, and greenhouse gas reduction as socio-economic benefits. Data from laboratory trials and case studies on black soldier fly and yellow mealworm reveal negative balances of socio-economic benefits and costs; however, it is possible that upscaling and more effective technologies could move this positively. Changes in nutrient market values could also shift the balance as well as prevent impact on marine ecosystems from reduction fishery; this was not evaluated but could contribute to the overall outcome. Thus, although the current assessment shows a negative balance, it does not necessarily mean that the production of insect meal for feed is not beneficial for society in the long term. Sustainability targets set by the United Nations, such as Zero Hunger by 2030, encourage the search for innovative solutions to enhance food production while preserving the environment. Alternative protein sources for feed, while conventional resources like soymeal and fishmeal become more expensive and scarcer, is one of the possibilities. Studies on substituting fishmeal with insect meal show promising results in terms of animal growth and feed efficiency. This paper aims to assess the socio-economic benefits and costs of insect meal substituting fishmeal in feed and to highlight the factors influencing performance most. The study evaluates the economic value of insect-based products, waste reduction, and reduced greenhouse gas emissions as socio-economic benefits. It combines empirical data derived from laboratory trials and two case studies covering black soldier fly (Hermetia illucens) and yellow mealworm (Tenebrio molitor). Current analyses reveal negative socio-economic balances, emphasizing that reduction of operating and investment costs through upscaling and technological advancements can give a positive move, as well as factors such as current market valuations for nutrients can change significantly. Thus, a negative balance at the moment does not mean that insect rearing, and larva processing are not desirable from a long-term socio-economic perspective. [ABSTRACT FROM AUTHOR]

This comprehensive review addresses the vital environmental concerns posed by conventional petroleum-based plastics, particularly in the context of the packaging industry's extensive reliance on these materials. As nearly 99% of plastics originate from non-renewable petrochemical sources and their non-biodegradable nature leads to widespread waste accumulation and harmful emissions upon disposal, the need for sustainable alternatives has become paramount. This paper explores the escalating environmental and health repercussions linked to traditional plastics, underscored by global initiatives, including restrictions on single-use plastics, aimed at mitigating these challenges. In response, the paper highlights the growing interest in environmental friendly biopolymers, which can be sourced from renewable biological materials or synthesized from biopolymers such as starch, casein etc. The classification of biopolymers into three primary categories; natural biopolymers, microbial fermentation-derived biopolymers, and polymerized monomers from biomass is comprehensively examined. Furthermore, the paper emphasizes the pivotal role of biopolymer properties, such as barrier characteristics, mechanical strength, heat resistance, biodegradability, flexibility, food contact safety, and cost-effectiveness, in determining their suitability for packaging applications. It also stresses the importance of conducting life cycle assessment (LCA) to holistically evaluate the environmental sustainability of biopolymers. This review highlights the potential of integrating biopolymers into packaging materials as a promising avenue to reduce the adverse environmental impact of traditional plastic production. These biodegradable materials, with their diverse properties and renewability, offer a sustainable approach to mitigating plastic waste and lowering greenhouse gas emissions. However, further research, development, and collaborative efforts are essential to optimize biopolymer performance, reduce production costs, and facilitate broader adoption. Embracing biodegradable polymers represents a commitment to resource efficiency, waste reduction, and environmental preservation, fostering a more sustainable and ecofriendly future. [ABSTRACT FROM AUTHOR]

As the global shipping industry experiences rapid expansion, the imperative to address greenhouse gas emissions and environmental impact becomes increasingly paramount. Hydrogen has emerged as a pivotal and eco-friendly energy source, offering a pathway towards carbon neutrality and a complete zero-carbon transition in maritime operations. However, the widespread adoption of hydrogen-powered ships hinges on the establishment of robust regulations and technical standards. This paper conducts a comprehensive examination of hydrogen fuel cell (FC) technology in ships, scrutinizing the role of international classification societies and exploring existing standards and regulations within the maritime industry, specifically centered around hydrogen energy. The study outlines a strategic developmental roadmap for a green shipping hydrogen energy system tailored for hydrogen FC-powered ships in China. Emphasizing the differences in hydrogen application between fuel cell vehicles and ships, the paper elucidates technical challenges unique to hydrogen FC-powered ships. Furthermore, it proposes a visionary framework for future technical standards, advocating for the creation of a ship-based hydrogen energy standard system, the development of core technical standards, and a heightened focus on safety regulations. Through comprehensive analysis and compelling argumentation on hydrogen fuel cell ship technology and standards, this paper underscores the indispensable role that technical standards play in propelling the advancement of environmentally friendly shipping. Beyond serving as an informative resource, the paper aims to provide valuable guidance and direction for the future demonstration, application, and promotion of hydrogen fuel cell ship technology. Ultimately, it underscores the pivotal role of technical standards in advancing sustainable maritime transportation. • Analyze hydrogen energy technical standards from the production, storage, safety. • Comparison of hydrogen energy technical differences between vehicles and ships. • Outline the unique challenges of applying hydrogen technology to ship operations. • Constructed a technical standard framework for future hydrogen energy ships. [ABSTRACT FROM AUTHOR]

The paper reviews and evaluates a 30-year-long atmospheric CO2 data series measured at Hegyhátsál tall-tower greenhouse gas monitoring site, a member of WMO GAW, NOAA, and ICOS networks (id. code: HUN). The paper also gives the technical description of the monitoring system, and that of the physical environment of the station. This low elevation (248 m above m.s.l.), mid-continental Central European site shows a 3.90±0.83 µmol mol‑1 offset relative to the latitudinally representative marine boundary layer reference concentration presumably due to the European net anthropogenic emissions. The long-term trend (2.20 µmol mol‑1 year‑1) closely follows the global tendencies. In the concentration growth rate, the ENSO effect is clearly detectable with a 6–7 months lag-time. The summer diurnal concentration amplitude is slightly decreasing due to the faster-than-average increase of the nighttime concentrations, which is related to the warming climate. The warming climate also caused a 0.96±0.41 day year‑1 advance in the beginning of the summer CO2-deficit season in the first half of the measurement period, which did not continue later. [ABSTRACT FROM AUTHOR]

Nowadays, one of the main challenges facing green innovation management is how to enhance the performance of innovation processes by utilizing asymmetric input and output data. Therefore, this paper develops an improved SBM model analysis framework for evaluating the green innovation efficiency of asymmetric input and output data. The framework is applied to assess the technical (TE), managerial (PTE), and scale (SE) efficiencies of new energy companies under three input variables (R&D personnel input, R&D capital input, and comprehensive energy consumption input), two desirable output variables (green technology output and economic output), and one undesirable output variable (greenhouse gas emissions). Then, environmental factors and random factors are eliminated from the obtained input slack variables based on the SFA model, placing decision-making units in a homogeneous environment. The results demonstrate that TE, PTE, and SE are improved after eliminating environmental factors and random factors. Subsequently, based on the entropy method, this paper classifies companies' green innovation patterns into four categories and provides targeted solutions. The purpose of this paper is to provide an evaluation method for new energy companies to understand green innovation efficiency and assist decision makers in identifying the most optimal resource allocation approach. The proposed improved SBM model contributes to the literature and to industry practice by (1) providing a reliable evaluation of green innovation efficiency under asymmetric input and output data; (2) determining effective improvement actions based on a slack analysis of environmental variables and random variables that lead to improved process performance; and (3) making fuzzy innovation performance efficient to facilitate understanding and managing innovation resource allocation quality. [ABSTRACT FROM AUTHOR]

This paper defends strong emissions sufficientarianism as an approach to assigning moral rights to generate greenhouse gas emissions. Strong emissions sufficientarianism holds that only subsistence emitting is morally permissible. This paper argues that, since it is uncertain how many subsistence emissions there will be, the present generation owes it to future generations to refrain from generating non-subsistence emissions, not to risk imposing on them a tragic choice between sacrificing themselves and contributing to very dangerous climate change. The paper also addresses the charge that emissions sufficientarianism, in general, is too permissive since it entails a right to contribute to very dangerous climate change. The overall message is that, given the moral urgency posed by climate change, there is little room for distributive principles besides emissions sufficientarianism. This casts doubt on the appropriateness of relying on carbon budgets in assigning rights to emit. [ABSTRACT FROM AUTHOR]

Peatlands cover only 3–4% of the Earth's surface, but they store nearly 30% of global soil carbon stock. This significant carbon store is under threat as peatlands continue to be degraded at alarming rates around the world. It has prompted countries worldwide to establish regulations to conserve and reduce emissions from this carbon rich ecosystem. For example, the EU has implemented new rules that mandate sustainable management of peatlands, critical to reaching the goal of carbon neutrality by 2050. However, a lack of information on the extent and condition of peatlands has hindered the development of national policies and restoration efforts. This paper reviews the current state of knowledge on mapping and monitoring peatlands from field sites to the globe and identifies areas where further research is needed. It presents an overview of the different methodologies used to map peatlands in nine countries, which vary in definition of peat soil and peatland, mapping coverage, and mapping detail. Whereas mapping peatlands across the world with only one approach is hardly possible, the paper highlights the need for more consistent approaches within regions having comparable peatland types and climates to inform their protection and urgent restoration. The review further summarises various approaches used for monitoring peatland conditions and functions. These include monitoring at the plot scale for degree of humification and stoichiometric ratio, and proximal sensing such as gamma radiometrics and electromagnetic induction at the field to landscape scale for mapping peat thickness and identifying hotspots for greenhouse gas (GHG) emissions. Remote sensing techniques with passive and active sensors at regional to national scale can help in monitoring subsidence rate, water table, peat moisture, landslides, and GHG emissions. Although the use of water table depth as a proxy for interannual GHG emissions from peatlands has been well established, there is no single remote sensing method or data product yet that has been verified beyond local or regional scales. Broader land-use change and fire monitoring at a global scale may further assist national GHG inventory reporting. Monitoring of peatland conditions to evaluate the success of individual restoration schemes still requires field work to assess local proxies combined with remote sensing and modeling. Long-term monitoring is necessary to draw valid conclusions on revegetation outcomes and associated GHG emissions in rewetted peatlands, as their dynamics are not fully understood at the site level. Monitoring vegetation development and hydrology of restored peatlands is needed as a proxy to assess the return of water and changes in nutrient cycling and biodiversity. [ABSTRACT FROM AUTHOR]

Pulp and paper industry is one of the eight critical industries for controlling carbon emissions in China. As the paper productions increase, the pulp and paper industry may fail in achieving the emission reduction target due to the rapid growth of greenhouse gas emissions. The study uses life cycle assessment to evaluate the greenhouse gas emissions of China's papermaking industry chain in order to propose emission reduction targets and find ways to achieve the emission reduction targets for China's papermaking industry. Considering the net carbon absorption of plant raw materials and the extensive paper industrial chain, this study obtained that the greenhouse gas emission of major paper types under corresponding pathways ranges from 1.96 t CO 2 eq/t paper to 6.55 t CO 2 eq/t paper. Plant carbon sink can reduce greenhouse gas emissions by 14.3%–42.9% under virgin fiber-based pathways. This study found that the greenhouse gas emissions caused by terminal products of 814 papermaking enterprises counted in China were 282.23 Mt CO 2 eq in 2015, accounting for 10.23% of the total greenhouse gas emissions of manufacturing industries and construction. To achieve the emission reduction target by 2050, emissions of the pulp and paper industry in China have been investigated from the perspective of three ideal energy structures. The research findings show that the emission reduction target of Intended Nationally Determined Contribution will be achieved in 30 years if the energy structure of the pulp and paper industry is adjusted only based on the optimal 450 scenario. In terms of other energy structures, the pulp and paper industry should assume afforestation areas ranged from 5900 km2 to 223,000 km2 at least to make up for the greenhouse gas emissions beyond allowance, which accounts for 0.85%–32.16% of the existing areas of plantation forestry in China. • Statistics in this work reveal the problem of excess capacity in China's pulp and paper industry. • GHG emission of paper products in different pathways range from 1.95 to 6.52 t CO 2 eq/t paper. • Energy supply mode transition is conductive to green development of pulp and paper industry. • Pulp and paper enterprises should assume afforestation areas to achieve emission reduction targets. [ABSTRACT FROM AUTHOR]

Summary: In this article, we explore why dairy science, technology, and innovation will for the foreseeable future remain important, and some of the future trends we can expect in the field. Given the nutrient richness and density of milk, its ubiquitous production and utility of use to produce foods and food ingredients, dairy will almost certainly continue to play an important role in diets and the global food system. Annual milk production at over 900 billion litres represents approximately 8% of total food biomass but has a disproportionate contribution to global nutrient provision. The value of the global dairy market will reach over $860 billion in 2024, employing approximately 240 million people, and supporting the livelihoods of up to one billion. The importance and long history of dairy has fuelled a vast amount of research in dairy science and technology with hundreds of thousands of papers published in the field. Given the amount of existing dairy science and technology is there anything significant left to be done? However, with advances in numerous other fields such as materials, biology and biochemistry, analytical technology, computing technology, etc., the opportunities in dairy science and technology also advance. Future innovations in the dairy sector will include those relating to environmental science and technology, the food matrix, foods tailored to diets for life stages and lifestyles, developments based on our expanding knowledge of microbiomes, and new opportunities from the use of AI. Dairy is the target for technology‐enabled disruption by those looking to produce substitute products. Some of the technologies to produce dairy alternatives will feature in the future of dairy innovation but the impact is more likely to complement rather than disrupt the dairy sector. [ABSTRACT FROM AUTHOR]

The quality assurance of the earth-atmosphere system, which runs primarily to temperature variations and other disturbances of the earth's climate, compels the assessment of greenhouse gases (GHG) emissions due to various Organizations for Economic Co-operation and Development (OECD) countries' human activities that disturb the radioactive energy balance. The purpose of this paper is to thus determine the usefulness and acceptability of statistical process control for assessing the level of GHG emissions from OECD countries. We apply the exponentially weighted moving average (EWMA) control charts with one-time, two-time, and three-time smoothing processes for monitoring the process variance under a repetitive sampling scheme, named S 2 -EWMA RS , S 2 -DEWMA RS and S 2 -TEWMA RS charts, and also utilize a cumulative sum (CUSUM) control chart under a repetitive sampling scheme, named as S2-CUSUMRS chart, to assess these countries' emission levels of GHG. The control charts are a graphical representation of the trend product of sequential procedures. All the OECD countries can thus independently measure their emission level of GHG as a self-assessment tool. Consequently, we recommend use of the advanced control charts as a tool for OECD assessment at an individual country level. [ABSTRACT FROM AUTHOR]

There is scope for improving the sustainability of intensive dairy farms through the uptake of sustainable production practices such as more grass‐based feeding systems. Such feeding systems can reduce feed‐food competition and the environmental impacts of feed production, among other farm‐level and societal benefits. However, empirical research on how farmers' feed choices mis(align) with sustainability transitions and the associated drivers is limited. This paper explores the trade‐offs that farmers make between the environmental, social and economic sustainability impacts of grass‐based feeding systems based on data from Swedish dairy farmers. Using an identity‐based utility framework and a hybrid latent class model, we find substantial heterogeneity in dairy farmers' trade‐offs between feed‐related sustainability attributes: greenhouse gas emissions, biodiversity, animal welfare, feed self‐sufficiency, feed cost and milk yield. Furthermore, our findings demonstrate that farmers who are strongly interested in the environmental and social sustainability impacts of their dairy feeding systems, beyond economic gains, are motivated mainly by their pro‐environmental and pro‐social identities. Overall, our findings imply that identity‐enhancing interventions are promising policy instruments for encouraging the uptake of more grass‐based feeding systems. [ABSTRACT FROM AUTHOR]

The European Climate Law sets a legally binding target of net zero greenhouse gas emissions by 2050. In this regard, in 2023 the EU Environmental Council decided that from 2035 onwards only CO2‐neutral new cars will be licensed in the European Union. Simultaneously, since the energy crisis caused by the Russian invasion of Ukraine, fuel prices increased in Germany. This has made more and more households think about purchasing an e‐car. However, not every household has the opportunity to install their own wallbox, and when travelling long distances, e‐car users are dependent on the availability of ample public charging stations. Against this background, with a special focus on rural areas, this paper considers the questions whether and where spatial inequalities in the accessibility of public charging stations might currently exist. To approach these questions, based on an empirical analysis of the 2023 official location data of public charging points in Germany, we examine the nationwide distribution, accessibility and available capacity of public charging stations in Germany at small‐scale from the point of view of the 'household' as well as those who travel by e‐car within Germany. In order to evaluate the location data of public charging stations we mainly use raster‐based accessibility analysis methods as well as isotropic kernel intensity estimates. We found that, in contrast to the common belief, the network of public charging stations is quite dense. However, taking a closer look reveals that the charging infrastructure in Germany has so far been tailored to the needs of intra‐regional travelers (commuting, shopping, leisure) rather than to those of the residential population with no access to their own wallbox (daily recharging in close proximity to one's home) or the mid‐ to long‐distance travelers. [ABSTRACT FROM AUTHOR]