Search

This research investigated the influence of the layered structure of paper on its selected strength properties. Two types of cellulose pulp were used: unbleached kraft pine pulp (UBSK) and unrefined bleached birch kraft pulp (BHK). Multi-ply papers were obtained from layers of appropriate grammage formed separately and bonded in a wet state. Paper layers were formed from primary pulps (UBSK and BHK) or their mixtures (threeply UBSK-BHK paper and three-ply UBSK-BHK-UBSK paper), from which various variants of laboratory paper samples were made. This work focused on three-layer papers. The obtained laboratory sheets were analysed for changes in tear resistance, tensile strength, bursting strength, short span compression strength (SCT), and corrugating medium test (CMT). In most cases, three-layer structures were characterised by higher strength parameters than single-layer papers. The tear strength and SCT of papers consisting of three layers formed from both mixed pulps were slightly lower than those of solid papers. The results demonstrate the feasibility of producing three-ply paper with significantly reduced variability in parameters such as elongation and bursting strength, which are inherently subject to high variability. [ABSTRACT FROM AUTHOR]

Paper, which is in fact a very complex cellulose-based product derived from different lignocellulosic resources, is usually regarded as a simple omnipresent commodity in our lives. Wood fibers derived from trees are the most employed sources for papermaking purposes. From an environmental protection perspective, and for their essential role in our life (they give us the life itself through their foliar system supporting the photosynthesis process), trees should not be extensively cut down and they should be used less and less for papermaking. Thus, employment of non-woody alternative sources for papermaking could be exploited more as an attractive and feasible option. [ABSTRACT FROM AUTHOR]

This paper reviews key advances in understanding the hydrodynamics of the forming section of papermaking during the years 1950 to 2000. Over this period papermaking advanced from rather slow-speed Fourdrinier machines to modern high-speed twin-wire formers. The advances are described in the context of technical problems faced at the time to increase machine speeds and improve paper properties. The scientific work and advances in machine design contributed greatly to the marvel of modern papermaking, which now includes machines 10 m wide operating at speeds over 100 km/h. [ABSTRACT FROM AUTHOR]

A variety of the Leucaena genus, Leucaena diversifolia, was used for pulp and paper making by kraft and refining processes and a OD(EP)DP bleaching sequence. The same species has been suggested as an energy crop and, in fact, this species used shows a high gross heating value; besides, this variety of Leucaena has appropriate characteristics for pulp and paper making. The holocellulose content was higher than Eucalyptus globulus, and ash and lignin contents were comparable to other varieties of Leucaena. Pulps with a kappa number between 17 and 18, and 21.4 cP viscosity were obtained using an active alkali concentration of 31%. Also, paper sheets showed good strength properties, comparable or even greater than those obtained with Eucalyptus or others varieties of Leucaena at comparable refining degrees, between 30 and 40 °SR. The pulp was successfully bleached in all cases with a kappa number below 1.5 in the EP stage and a value of brightness higher than 90%. [ABSTRACT FROM AUTHOR]

This article describes a facile method for the preparation of cellulosic catalyst paper: the in situ synthesis of gold nanoparticles (AuNPs) on zinc oxide (ZnO) whiskers, the preferential support for AuNPs, preloaded into a paper matrix. The ZnO paper composites were fabricated using a high-speed and low-cost paper-making technique, and immersed in an aqueous solution of HAuCl4. After drying, fine 5 nm AuNPs were successfully formed on the ZnO whiskers inside the paper matrix. As- prepared AuNPs@ZnO whisker-containing paper (AuNPs@ZnO paper) is similar to ordinary paper products, being flexible, lightweight, and easy to handle. The AuNPs@ZnO paper exhibited a high catalytic efficiency towards the reduction of 4-nitrophenol to 4-aminophenol in aqueous media. Furthermore, the addition of a polyamideamine epichlorohydrin resin provided a wet strength to the AuNPs@ZnO paper, which enables several catalyst recycles with no significant losses in catalytic activity. [ABSTRACT FROM AUTHOR]

Surface treatment is an important step of papermaking, namely for improving the final product quality. For uncoated printing and writing papers (P&W), surface sizing is becoming a common practice for controlling paper surface characteristics and liquid spreading and absorption. This work aims at evaluating the potential of assessing and controlling paper surface chemistry, by analyzing the impact of the application of different surface sizing formulations both on the chemical surface characteristics of the modified paper samples and on the final printing quality. For that, blends of cationic starch and minor quantities (5%, 10%, and 20% w/w) of four distinct copolymers of styrene were used, resulting in a total of 12 different surface sizing formulations. A sample surface sized only with cationic starch was taken as reference. Surface chemical properties were determined by using contact angle measurements and inverse gas chromatography. Finally, the inkjet printing quality was evaluated. The results revealed that the surface sizing treatments tested have a substantial influence on the surface energetics and partially explain the differences detected in the inkjet printing quality. [ABSTRACT FROM AUTHOR]