Search

The eco-design considers the factors to prepare biocomposites under an end-of-life scenario. PLA/sisal biocomposites were obtained from amorphous polylactide and sisal loadings of 10, 20 and 30 wt% with and without coupling agent, and subjected to biodegradation in soil according to standard ISO846. Mass-loss, differential scanning calorimetry and size-exclusion chromatography were used for monitoring biodegradation. A statistical factorial analysis based on the molar mass M n and crystallinity degree X C pointed out the relevance and interaction of amount of fibre and use of coupling agent with the time of burial in soil. During the preparation of biocomposites, chain scission provoked a similar reduction of M n for coupled and non-coupled biocomposites. The amount of fibre was relevant for the increase of X C due to the increase of nucleation sites. The coupling agent accelerated the evolution of both factors: reduction of M n and the consequent increase of X C , mainly during biodegradation in soil. Both factors should be balanced to facilitate microbial assimilation of polymer segments, since bacterial digestion is enhanced by chain scission but blocked by the promotion of crystalline fractions. [ABSTRACT FROM AUTHOR]

Environmental awareness of the global waste problem has driven the development of new green composites made from either renewable or biodegradable materials. Among the variety of available green composites, natural composites based on poly-lactic acid (PLA) have shown noteworthy performance due to their short degradation time after disposal, good strength, and ease of processing by conventional methods. In particular, green composites manufactured with PLA matrix reinforced with Manicaria Saccifera fabric (MF) display mechanical properties that have shown to be very competitive compared with similar materials. In this study, the tensile properties of a green composite of PLA reinforced with MF are optimized by using a Taguchi method approach. The processing parameters, fabric chemical treatment parameters, compression molding parameters, and fiber content are analyzed simultaneously to yield the optimum biocomposite properties. The predicted optimum parameters are experimentally verified. Tensile tests and scanning electron microscope (SEM) analysis are used. Significant improvements on both the tensile strength (114.2%), and the elastic modulus (120.6%) of the biocomposite are achieved. [ABSTRACT FROM AUTHOR]

Biocomposites with tunable properties were successfully prepared through ionic assembly between anionic carboxymethyl cellulose (CMC) and cationic copolymers (quaternized poly( l -lactide)-block-poly N , N -dimethylamino-2-ethyl methacrylate) (PLA- b -PDMAEMA). The quaternized PDMAEMA segment not only works as a compatibilizer between hydrophilic CMC and hydrophobic PLA, but also acts as a lubricant between these two rigid biopolymers. The 1 H NMR (nuclear magnetic resonance) spectra demonstrated successful synthesis of PLA- b -PDMAEMA with controlled molecular weight of PDMAEMA segment. The results from scanning electronic microscopy (SEM) and Fourier transform infrared spectrometry (FTIR) verified the interaction between quaternized copolymer micelles and anionic CMC networks. The resultant biocomposite could form a transparent and uniform film after casting. Both storage moduli and maximum degradation temperature of PLA/CMC composites were increased with the reduction of molecular weight of PDMAEMA segments. It suggests that the properties of biocomposite materials can be tailored by adjusting the chain length of inclusive PDMAEMA segment. [ABSTRACT FROM AUTHOR]

Highlights: [•] PLA/kenaf biocomposites were prepared using extrusion and compression molding. [•] APP increased flame retardancy and thermal properties of biocomposites. [•] APP decreased compatibility between the PLA and kenaf fiber. [•] Alkali treatment improved thermal stability and decreased char formation. [Copyright &y& Elsevier]

Abstract: Over the last few years, intensive research has been devoted to the exploitation of “green products” based on natural resources for both matrices and as reinforcements in composite systems. The mechanical properties of reinforced biocomposites, such as flax/polylactic acid (PLA), are largely governed by interfacial properties between the two constituents apart from their intrinsic properties. Although many papers indirectly demonstrate the importance of optimising the interface between these two polymers, the exact nature of the interaction between the natural fibre and the polymeric matrix has not been clearly investigated on a fundamental level and is presently a major technological limitation of these materials. This work presents the first direct study of adhesion forces, by colloidal force microscopy, between smooth PLA films representing the polymer matrix, and a microbead of cellulose that mimic the cellulose material in flax fibres. Normalised adhesion force measurements have shown the importance of capillary forces when experiments were carried out under ambient conditions. Experiments, conducted under dry air, allowed for the deduction of the contribution of pure van der Waals forces, and our results, through the calculation of the Hamaker constant, show that these forces, for the PLA/cellulose/air system, were lower than those obtained for the cellulose/cellulose/air system and hence underlined the importance of optimising the interface among these materials. This study demonstrates the capacity of AFM to probe direct interactions in complex systems by adjusting the nature of the surface and the probe to mimic the materials in contact. Furthermore, the technique can be operated in a variety of environments, consistent with composite making and provides particular opportunity for testing and improving the properties of these new classes of composite materials. [Copyright &y& Elsevier]