Search

Phosphorylated fibers offer a broad range of applications, particularly in thermal insulation, notably with wood fibers, provided they exhibit improved mechanical characteristics. Despite encountering challenges in applying traditional papermaking methods, the creation of paper or board sheets with phosphorylated pulp fibers remains a challenge. Findings suggest that phosphorylation-modified fibers show increased roughness. Moreover, in comparison with unbeaten kraft sheets (KF) and thermomechanical pulp sheets (TMP), those made from phosphorylated kraft fibers (PKF), using a cationic coagulant and a flocculant, demonstrate significant enhancements in burst index, break index, and tensile energy absorption by 2.12 times, 1.7 times, and 2.77 times, respectively. Similarly, phosphorylated TMP sheets, prepared with a dual polymeric system (coagulant/flocculant), exhibit improvements of 1.42 times, 1.33 times, and 1.82 times, respectively, in these properties. The study emphasizes the ameliorating effect of cationic polymeric agents on the charge impact of phosphorylated fibers on overall sheet quality, while also highlighting the substantial influence of hot-pressing lignin-containing paper on all determined physical properties. [ABSTRACT FROM AUTHOR]

Banana stem is a known alternative to wood for the production of pulp and paper. During the production of paper, it is extremely important to save costs and time while at the same time enhancing quality of produced paper. In the present study, paper was developed from banana stem fiber by optimizing its density. Response surface methodology (RSM) using Box-Behnken design (BBD) was used to determine optimum blending parameters of the developed papers. The influence of banana stem fiber amount (250-1000 g), water amount (1-2liters) and blending time (5-10 min) on paper density was ana)lyzed using software Stat-Ease 360, Version 13. The optimum conditions of banana stem fiber amount, water amount and blending time to achieve a density of 675.75 g/m3 were determined as 461.83 g, 1.31liters, and 8.53 min, respectively. ANOVA results revealed that the quadratic model best fits the density response, with blending time and banana stem fiber amount as the most significant model terms. Linear effects were more predominant than quadratic and interaction effects. The developed density model was in close agreement with experimental findings with an R² value of 0.9748. Developed paper had cellulosic contents, with volatiles as high as 82.11%wb and 2.11% wb ash composition. Future works on thermal properties of paper are encouraged. [ABSTRACT FROM AUTHOR]

The production of release coatings has been increasing in recent years because of their use in various fields. However, commercially available release coatings are regarded as non-recyclable. As a consequence, the repulping of these residues is difficult, and their presence in the recycling stream represents an important source of contamination. One solution to this problem is to use new coating materials that can replace the siliconized backing, provided that these new materials are recyclable. As a solution to this problem, the authors propose the use of alkylated phosphorylated fibers to produce an environmentally friendly and inexpensive release paper. The results show that a surface application of hydrophobic phosphorylated fibers reduces the surface free energy of the paper support, as well as the peel strength, which facilitates the separation of the adhesive tape. [ABSTRACT FROM AUTHOR]

This paper presents the limitations and potential of ATR-FTIR spectroscopy applied to the study of cellulosic textile collections The technique helps to differentiate natural fibres according to the content of lignin, pectin, hemicellulose, and wax, although some problematic issues should be considered. The spectral differences derived from the environmental humidity uptake and the plant composition are reviewed and discussed in the light of new experimental data. Diagnostic bands are proposed that can discriminate between different fibres from different plants. The contribution of ageing is also considered, demonstrating that sometimes aged fibres cannot be reliably recognised. In contrast, the potential of ATR-FTIR spectroscopy to discriminate between natural and modified fibres is discussed and proven. The best results were obtained when microinvasive ATR-FTIR spectroscopy was coupled with SEM observations. The proposed protocol was tested on microsamples of various cellulosic materials from traditional Japanese samurai armours dating from the 16th to the 20th centuries (Morigi Collection, Museo delle Culture, Lugano, Switzerland). The results facilitated a complete characterisation of the materials and demonstrated that the protocol can be used to study a wide variety of cellulosic materials, including both natural and man-modified fibres, and paper. [ABSTRACT FROM AUTHOR]

• 72% − 80% of fibre was recovered from disposable coffee cups. • 2% and 3% consistency shredded cups required > 100 kWh/tonne to repulp with 3 refiner passes. • Pulp quality did not significantly diminish after repulping using a single-disk refiner. Over 64 billion paper-plastic laminate (PPL) coffee cups are consumed between the United States and Canada annually, the majority accumulating in landfills due to a hydrophobic plastic inner-lining. Recycling can mitigate environmental damage and provide economic value from repurposed products. We found that standard repulping methods were insufficient to separate fiber from plastic due to the low intensity of treatment. To increase process intensity, we mechanically refined shredded PPL coffee cups and Kraft eucalyptus sheets (control) at 2%, 3%, and 4% consistencies with three passes to determine the energy required to separate fibers from plastic and the effects on fiber quality. 2% and 3% consistency PPL cups measured under 40 kWh/tonne of input material for one refiner pass and ∼ 80 kWh/tonne for 4% consistency PPL cups. Recovered fiber fraction totaled 87.7%, 85.3%, and 80.5% of input mass of Kraft eucalyptus and 72.3%, 72.6%, and 79.6% of input mass of PPL cups at 2%, 3%, and 4% consistency, respectively. Fines content of PPL cups jumped from 8% pre-refining to ∼ 30% post-refining while Kraft eucalyptus fibers were unaffected, suggesting that breaking the plastic-fiber bonds results in fines generation. Mean fiber length of PPL cups slightly decreased with consistency and tensile strength improved. Freeness decreased with consistency only in PPL cup samples. These results demonstrate a low energy requirement to effectively separate fiber and plastics in PPL cups as well as minimal impact on fiber quality using existing refining technology, and provides an estimate of the financial costs of local recycling efforts. [ABSTRACT FROM AUTHOR]

Xylan is primarily found in the secondary cell wall of plants providing strength and integrity. To take advantage of the reinforcing effect of xylan in papermaking, it is crucial to understand its role in pulp fibers, as it undergoes substantial changes during pulping. However, the contributions of xylan that is added afterwards (extrinsic) and xylan present after pulping (intrinsic) remain largely unexplored. Here, we partially degraded xylan from refined bleached softwood kraft pulp (BSKP) and adsorbed xylan onto BSKP. Enzymatic degradation of 1 % xylan resulted in an open hand sheet structure, while adsorption of 3 % xylan created a denser fiber network. The mechanical properties improved with adsorbed xylan, but decreased more significantly after enzymatic treatment. We propose that the enhancement in mechanical properties by adsorbed extrinsic xylan is due to increased fiber-fiber bonds and sheet density, while the deterioration in mechanical properties of the enzyme treated pulp is caused by the opposite effect. These findings suggest that xylan is decisive for fiber network strength. However, intrinsic xylan is more critical, and the same properties cannot be achieved by readsorbing xylan onto the fibers. Therefore, pulping parameters should be selected to preserve intrinsic xylan within the fibers to maintain paper strength. [Display omitted] [ABSTRACT FROM AUTHOR]

Understanding water absorbency in paper is challenging as fibre swelling and out-of-plane deformation occur simultaneously during liquid imbibition. Liquid absorption is commonly accessed by gravimetric tests, which provides limited information on the local spatial and temporal distribution of fluid in the substrate. In this work, we developed iron tracers to map liquid imbibition in paper by in situ precipitation of iron oxide nanoparticles during passage of the wetting front. The iron oxide tracers were found to be robustly attached to the cellulosic fibres. After liquid absorption tests, absorbency was investigated by mapping the distribution of iron in 3D using X-ray micro-computed tomography (μCT) and in 2D using energy-dispersive X-ray spectroscopy. We demonstrate a difference in tracer distribution between the wetting front and the fully saturated region supporting that imbibition proceeds in two phases, i.e. liquid percolation through the cell wall initially prior to filling of the external pore spaces. Critically, we demonstrate that these iron tracers enhance image contrast and allow for new imaging modalities in μCT for fibre networks. [Display omitted] [ABSTRACT FROM AUTHOR]

Paper is a material exhibiting a complex microstructure that is composed of a network of fibres at the micro-level. When subjected to external loading or variations in moisture conditions over different time scales, changes in strain that are non-linear with respect to time are observed at the sheet level (macro-scale). In order to investigate this time-dependent behaviour of paper, a creep power law model is implemented within a finite element approach at the level of single fibres. This rate-dependent model is found to capture experimental results available in literature for single fibres with a good agreement (both quantitatively and qualitatively). Based on the identified model at the level of single fibres, the time-dependent hygro-mechanical response is upscaled towards the network scale. To this end, random model networks of ribbon shaped fibres are generated and their response is simulated. The network-scale response, emerging from the rate-dependent fibre model, demonstrates the ability to predict the response of networks subjected to relaxation at a constant moisture level. The developed numerical model predicts lower values of overall stress response in single fibres as compared to networks. Also, stress relaxation predicted by the rate-dependent model in the cross-direction of the networks is in agreement with the experimental observations by Johanson and Kubát (1967). Therefore, one of the remarkable findings of the present work is that the developed rate-dependent model is robust enough to capture the sheet scale response also qualitatively. Based on the study of these computational results, a better understanding is achieved regarding the influence of mechanical and rate-dependent properties of single fibres on the hygro-expansion of complete fibre networks, and in particular of paper sheets. • A rate-dependent non-linear model is developed to study creep in paper networks. • It is calibrated with experiments on the single paper fibres with a good match. • It also captures the experimental response of the networks qualitatively. • One of the remarkable achievement of our work is the robustness of the model. [ABSTRACT FROM AUTHOR]