Search

Thermoplastic resin transfer molding (T-RTM) technology was applied to synthesize graphene nanoplatelets-based nanocomposites via anionic ring-opening polymerization (AROP). Polyamide 6 (PA6) was obtained by AROP and was used as the polymeric matrix of the developed nanocomposites. The non-isothermal crystallization behavior of PA6 and nanocomposites was analyzed by differential scanning calorimetry (DSC). Nanocomposites with 0.5 wt.% of graphene nanoplatelets (GNPs) with two different diameter sizes were prepared. Results have shown that the crystallization temperature shifted to higher values in the presence of GNPs. This behavior is more noticeable for the nanocomposite prepared with smaller GNPs (PA6/GN). The crystallization kinetic behavior of all samples was assessed by Avrami and Liu's models. It was observed that GNPs increased the crystallization rate, thus revealing a nucleating ability, and also validated the reduction of half-time crystallization values. Such tendency was also supported by the lower activation energy values determined by Friedman's method. [ABSTRACT FROM AUTHOR]

Carboxymethyl cellulose use in industry is ubiquitous. Though it is recognized as safe by the EFSA and FDA, newer works have raised concerns related to its safety, as in vivo studies showed evidence of gut dysbiosis associated with CMC's presence. Herein lies the question, is CMC a gut pro-inflammatory compound? As no work addressed this question, we sought to understand whether CMC was pro-inflammatory through the immunomodulation of GI tract epithelial cells. The results showed that while CMC was not cytotoxic up to 25 mg/mL towards Caco-2, HT29-MTX and Hep G2 cells, it had an overall pro-inflammatory behavior. In a Caco-2 monolayer, CMC by itself increased IL-6, IL-8 and TNF-α secretion, with the latter increasing by 1924%, and with these increases being 9.7 times superior to the one obtained for the IL-1β pro-inflammation control. In co-culture models, an increase in secretion in the apical side, particularly for IL-6 (692% increase), was observed, and when RAW 264.7 was added, data showed a more complex scenario as stimulation of pro-inflammatory (IL-6, MCP-1 and TNF-α) and anti-inflammatory (IL-10 and IFN-β) cytokines in the basal side was observed. Considering these results, CMC may exert a pro-inflammatory effect in the intestinal lumen, and despite more studies being required, the incorporation of CMC in foodstuffs must be carefully considered in the future to minimize potential GI tract dysbiosis. [ABSTRACT FROM AUTHOR]

In recent years bioactive textiles have risen to the forefront of consumers perception due to their potential protection against virus, fungi and bacteria. However, traditional textile staining is an eco-damaging process that and current methods of textile functionalization are expensive, complicated and with great environmental impact. With that in mind, this work sought to show a possible solution for this problematic through the usage of a novel one step textile dyeing and functionalization method based upon nanoencapsulated textile dyes (NTDs). To do so navy blue everzol NTDs were produced with chitosan, cotton dyed, characterized through FTIR and SEM and biological potential evaluated through biocompatibility screening and antimicrobial activity against skin pathogens. The data obtained showed that NTDs effectively dyed the target textile through a coating of the cotton fibre and that NTDs formed hydrogen bonds with the cellulose fibre via electrostatic interactions of the chitosan amino groups with cotton sulphate groups. From a biocompatibility perspective NTDs dyed cotton had no deleterious effects upon a skin cell line, as it promoted cellular metabolism of HaCat cells, while traditionally died cotton reduced it by 10%. Last but not least, NTDs dyed cotton showed significant antimicrobial activity as it reduced viable counts of MRSA, MSSA and A. baumannii between 1 and 2 log of CFU while traditional dyed cotton had no antimicrobial activity. Considering these results the novel method proposed shows is a viable and ecological alternative for the development of antimicrobial textiles with potential biomedical applications. [ABSTRACT FROM AUTHOR]

This work aimed to study the effect of the incorporation of graphene nanoplatelets (GRA 0.5% and 1% (w/w)) on the matrices of biobased polymers composed of starch-based materials (B20) and poly(butylene succinate) (PBS) using pine rosin (RES) as a compatibilizer. Three formulations were produced (B20/RES/PBS, B20/RES/PBS/GRA0.5%, and B20/RES/PBS/GRA1%), and their mechanical properties (tensile, flexural, hardness, and impact), rheological behavior, thermal properties (thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC)), chemical analysis (Fourier transform infrared-attenuated total reflectance (FTIR-ATR) spectroscopy), and contact angle were evaluated. Hardness (Shore D), tensile, and flexural moduli increased, whereas elongation at break and toughness decreased as GRA content increased. FTIR studies strongly supported the existence of interactions between polymeric matrices and the large surface area of GRA. The viscosity flow curves were well fitted to the Cross-Williams-Landel-Ferry (Cross-WLF) model, and the three formulations exhibited non-Newtonian (shear-thinning) behavior. The analysis of water contact angles indicated that the formulation surfaces have hydrophilic behavior. All the samples are thermally stable, and the results of this study can be used to optimize the application of biobased graphene-based composites for applications in injection molding industries. [ABSTRACT FROM AUTHOR]

This work aims to evaluate the influence of two starch-based materials (B16 and B20) on the moisture sorption isotherms, determined at 30, 40, and 50 °C, where B16 contains 5% (w/w) more starch than B20. Thermodynamic functions (differential enthalpy (∆Hdif), differential entropy (∆Sdif), integral enthalpy (Δhint), integral entropy (ΔSint), free Gibbs energy (∆G), and spreading pressure (φ)) were used to understand the water-binding behaviors and the energy requirements to remove the moisture content from the surface of these materials. The moisture sorption isotherms exhibited type III behavior, and the Guggenheim–Anderson–de Boer (GAB) model was the most suitable to fit the experimental moisture adsorption data. The adsorption isotherms of microparticles were enthalpy-controlled, with isokinetic temperature values of 221.45 and 279.77 K for B16 and B20, respectively, being higher than the harmonic mean temperature (312.94 K). The values of ∆G were positive (45.274 and 44.307 kJmol−1 for B16 and B20, respectively), indicating a non-spontaneous process. The spreading pressure values increased with increasing water activity (aw) for all isotherms. Higher values of ∆Hdif and ∆Sdif obtained from B16 confirmed its higher number of sorption sites available for binding with water molecules when compared to B20, making it less suitable for application in the food packaging industry. [ABSTRACT FROM AUTHOR]