Search

This report presents an investigation into the use of carbon paper electrodes prepared from chitosan-adhered graphene magnetite nanoparticles for the analysis of Cr(VI). The preparation and storage of carbon paper electrodes is a simple process, and these electrodes are easier to replace than electrodes modified by more conventional methods. The electrochemical detection of Cr(VI) using square wave adsorption cathodic dissolution voltammetry (SWAdCSV) with high selectivity and sensitivity, as well as the optimum conditions for the preparation of the electrodes and the electrode parameters affecting the SWAdCSV signal, were the main points of focus of the investigation. Cr(VI) was detected linearly in the range of 4-40 μg L-1 with a detection limit of 2.84 μg L-1. The electrode output precision, calculated as %RSD, was 7.16% (n = 6), and this was the measurement used for the detection of Cr(VI) in standard and test samples with recoveries between 89% and 114%. The results were consistent with those obtained using the standard UV-Vis spectrophotometric method with a paired t-test at 95% confidence level. [ABSTRACT FROM AUTHOR]

Selective enrichment of La(III) by green material as an industrial raw material is of great research interest. In this study, the selective interaction between P and La(III) was utilized, and waste paper (WP) modified with phytic acid (PA) was used to adsorb La(III) from water using a simple one-pot method. The adsorption capacity was 237.23 mg g−1 (30 °C, pH = 5, initial concentration of 200 mg L−1). The equilibrium isotherm fitted the Langmuir isotherm model well. The adsorption equilibrium was reached after 15 min. The adsorption kinetics followed the pseudo-second-order kinetic model, indicating that the adsorption mechanism of the material towards La(III) is single-layer chemisorption. It selectively adsorbed La(III) from four coexisting substances (Pb, Ni, Cu, and Co). After six cycles, the adsorption efficiency of the adsorbent material remained at 60%. [ABSTRACT FROM AUTHOR]

Employing a one-pot Schiff-base condensation approach, the derivative "cholyl hydrazide Schiff base of phenothiazine" (ChHSB-PTZ) based on cholic acid has been synthesized and characterized via standard procedures. ChHSB-PTZ demonstrates exceptional sensitivity towards Sn(II) metal ion detection through fluorescence "turn-off" behavior based on chelation-enhanced fluorescence quenching (CHEQ) even in the presence of various cations and anions. Through modified Stern–Volmer and Stern–Volmer graph analyses, the binding constant (Ka) and limit of detection (LOD) were found to be 2.8 × 1010 M−1 and 2.2 nM, respectively. A 1 : 1 stoichiometry between ChHSB-PTZ and the Sn(II) metal ion was found via Job's plot. Moreover, the distribution of electronic states in the ChHSB-PTZ Schiff base and the sensing mechanism (CHEQ) were clarified through the use of 1H NMR titration spectroscopy and density functional theory (DFT) calculations. ChHSB-PTZ test paper strips are developed as an essential tool to improve the analytical applicability of the device and enable the rapid, accurate, and affordable detection of Sn(II) metal ions in environmental analysis. [ABSTRACT FROM AUTHOR]

As a kind of organic basic compound containing nitrogen, biogenic amine is released from food spoilage and considered as an indicator for monitoring food freshness. Herein, an excellent dual-emission ratiometric fluorescent sensor for eight kinds of biogenic amines was established via the facile mixing of pH-responsive carbon dots and Rhodamine B. The developed sensor shows a rapid response (10 s), low limit of detection (0.733–3.943 μM) and a wide linear range (0–150 μM). More importantly, a portable fluorescent filter paper was prepared by simple dispersing the filter paper in a solution mixture of carbon dots and Rhodamine B. The obtained fluorescent filter paper based sensor showed an obvious color change in the presence of biogenic amine vapor derived from shrimp and mushroom. The results revealed that this sensor could realize the on-site and visual detection of biogenic amines in real food samples, making it suitable for potential application in food safety monitoring. [ABSTRACT FROM AUTHOR]

Developing new forms of flexible zinc–air (Zn–air) batteries is crucial to economic growth. Nevertheless, the absence of an oxygen evolution reaction catalyst with high catalytic efficiency and low-cost causes instability of Zn–air battery cycling and economic unviability, respectively. In this paper, a leaf-like N-doped carbon structure with CoS2 nanoparticles self-supported on carbon fiber paper (CoS2-CZ@CFP) was developed as an air electrode for Zn–air batteries, which not only uses nonprecious metal elements, but also has a self-supporting configuration, enhancing the contact between the catalyst and electrode while facilitating the transfer of electrons. Sulfur as the source gas was introduced into Co-doped metal–organic skeletons (Co-ZIFs) anchored on carbon fiber paper (CFP) for in situ vulcanizing transition metal Co, which successfully ensures the uniform distribution of sulfide particles in the carbon matrix, hence enriching active catalyst sites. The CoS2-CZ@CFP demonstrated an overpotential of 1.611 V at J = 50 mA cm−2, superior to RuO2@CFP (1.814 V). A Zn–air battery fabricated using the synthesized CoS2-CZ@CFP exhibited an extended life cycle of 117 h. This research paves the way for a novel method of designing self-supporting configurations of sulfides and carbon matrix composites as promising air electrodes applicable to Zn–air batteries. [ABSTRACT FROM AUTHOR]

A robust superhydrophobic filter paper was developed through a coating technique, simple and facile, cost-effective, eco-friendly, and defensible, for wide portfolio applications. To develop super hydrophobic filter papers, the paper was coated with inorganic–organic hybrid nanocomposites comprising zinc oxide, chitin, and polycaprolactone (chitin–ZnO–PCL) and zinc oxide, chitosan, and polycaprolactone (chitosan–ZnO–PCL) hybrids through the grafting method. The preparation of a superhydrophobic surface by dip-coating deposition is a facile process. Zinc oxide nanoparticles grafted with chitin–PCL and chitosan–PCL hybrids coated on paper exhibit superhydrophobic properties. Water contact angle measurement carried out using a goniometer showed the average static water angle values of 145° and 160° for the chitin–ZnO–PCL and chitosan–ZnO–PCL grafted hybrid coated surfaces, respectively. The surface morphology of the coating was studied using scanning electron microscopy, X-ray powder diffraction, UV radiation, and Fourier transform infrared spectroscopy. In addition, durability, oil/water separation, bio-degradability, and self-cleaning ability through water flush-out were also studied and reported. The results show that the coated filter papers possess excellent superhydrophobic properties for real-time applications. [ABSTRACT FROM AUTHOR]

Naphthalenediimide derivative-absorbed papers, which were prepared by dropping chloroform solution, showed fluorescence under photoirradiation after exposure to vapors of small aromatic guests. The fluorescence intensity and maximum wavelength depended on the type of guest aromatic molecules, similar to the crystal. The naphthalenediimide derivative-absorbed papers showed vapochromic and mechanochromic properties. [ABSTRACT FROM AUTHOR]

A simple, portable and cost-effective paper-based analysis device is developed for quantitative determination of ascorbic acid (AA) based on the UV-induced oxidation of 3,3′,5,5′-tetramethylbenzidine (TMB). The method does not involve the introduction of any enzyme or external oxidants. More importantly, large equipment is not needed and only a 20 μL sample is needed for each analysis which only takes 8 min. The filter paper is pre-treated with TMB and it turns blue upon UV irradiation because TMB is a self-photosensitizer. The phenol hydroxyl groups of AA can inhibit photo-triggered oxidation resulting in a lighter blue color. The color signal is captured using a smartphone and analyzed using color analysis software. A series of factors that affect the performance of the device are investigated, including the concentration of TMB, buffer pH, channel selection, and irradiation time. The analytical performance is evaluated, and the results show that the method has a wide detection range of 0.05–1.0 mmol L−1 as well as a high selectivity and reproducibility. The proposed method is applied for assaying AA in beverage samples and a VC tablet, and the results correspond to those obtained using the UV method. The results of the recovery test of human serum indicate that the proposed method is feasible in biological samples. This device is easy to fabricate, and convenient to store and transport. It is a truly portable device which has great potential in the on-site assay. [ABSTRACT FROM AUTHOR]

Sulphur doped graphitic carbon nitride (SGCN) was effectively prepared and comprehensively described. A straightforward synthetic process based on thermal condensation was reported for the synthesis of SGCN using thiourea as a precursor. Cyclic voltammetry (CV) and differential pulse voltammetry were used to evaluate the electrochemical performance of cortisol. SGCN sheets were used to boost the electro-catalytic activity, exhibiting very exceptional electrochemical behaviour towards cortisol. As a result, we obtained a broad linear response range of 0.1–100 μM, as well as a comparatively low detection limit (15.8 × 10−8 M). Furthermore, the fabricated SGCN/CFP electrode shows excellent selectivity in the presence of a large number of possible interfering species. SGCN comprises (C with N and S) heteroatoms, which most likely would have led to a better current response towards cortisol detection. Furthermore, the structural defects that generate additional active sites on the surface of SGCN may enhance the quick electron transfer that occurs during the oxidation of cortisol. [ABSTRACT FROM AUTHOR]

Viologens exhibit excellent color responses to external stimuli owing to their desirable redox properties. They have been widely studied in electrochromic and photoluminescent materials. Generally, polymeric materials have better processing properties and longer service life than small organic molecules. Herein, a viologen-containing polyurethane was synthesized and used to prepare an electrochromic device and a paper-based amine detector. The obtained electrochromic device displayed an excellent electrochromic behavior when subjected to an external voltage as low as 1.0 V. Moreover, the designed paper-based amine detector exhibits a highly sensitive color-change response when exposed to liquid amine solutions (down to 1 ppm concentration) or gaseous ammonia. The results of this study demonstrated that the developed viologen-containing polyurethane exhibits excellent electrochromic performance and the designed amine-detecting paper chips are an excellent tool for amine detection. [ABSTRACT FROM AUTHOR]

Valproic acid (VPA) is mainly used in the clinic to treat epilepsy, for which the therapeutic window is narrow to avoid causing adverse reactions such as hepatotoxicity and teratogenicity. Therefore, timely therapeutic drug monitoring is needed. A hapten containing a benzene ring and an amino group was designed and used to screen a monoclonal antibody (mAb) 3G10 with high specificity and sensitivity. The IC50 value of mAb 3G10 was ascertained as 68.13 ng mL−1 through an indirect competitive enzyme-linked immunosorbent assay. A colloidal gold-based immunochromatographic strip (CG-ICS) for the detection of free VPA in human serum was developed with gold-labeled mAb 3G10. Qualitative analysis of human serum samples can be conducted through visual observation. The visual limit of detection (vLOD) was 2 μg mL−1, and the cut-off value was 100 μg mL−1. A standard curve for quantitative detection was generated using a portable scanner, with a calculated LOD (cLOD) value of 0.144 μg mL−1 and a linear range of 0.565–48.385 μg mL−1. Comparing the results of CG-ICS for actual positive samples with those of a direct chemiluminescence kit, there was a good correlation between the two methods. Therefore, our CG-ICS can be applied to the rapid clinical monitoring of free VPA. [ABSTRACT FROM AUTHOR]

The water-soluble bromophenoxy-substituted naphthalimide derivative 1 and its copolymer P1 with acrylamide were synthesized and the photophysical properties of their host–guest complexes with cucurbit[8]uril (CB[8]) were studied. Notably, the host–guest complex CB[8]·1 showed long-lived RTP on filter paper and demonstrated a humidity response, making it suitable for use as an encryption ink. Furthermore, the solid powder of the host–guest complex between P1 and CB[8] exhibited a 4 s afterglow emission. [ABSTRACT FROM AUTHOR]

We report the results of studies relating to the development of a conductive ink-coated, paper-based electrochemical DNA hybridization assay for the detection of the porA pseudogene of Neisseria gonorrhoeae (gonococcal DNA), the causative agent of gonorrhoea. Briefly, a conductive and highly homogenous ink was prepared by dispersing carboxylated MWCNTs (cMWCNTs) in a stable emulsion consisting of terpineol as solvent, carboxymethyl cellulose (CMC) as binder and polysorbate 80 (PS80) as the stabilizing agent. This cMWCNT-based ink was coated onto paper substrates to obtain cMWCNT@paper electrodes with a mean (± standard deviation, SD) resistivity of 1.066 (± 0.33) Ω cm. Furthermore, a magnetic bead (MB)-mediated hybridization assay comprising a specific 5′-biotinylated capture DNA probe (C) and 3′-methylene blue (MetB)-tagged detector DNA probe (D) was designed. These probes hybridized specifically with a porA target DNA sequence (T) forming a sandwich hybridization complex (C-T-D) at the MB surface. Thus formed C-T-D/Av/MB samples with different T concentrations were drop cast and adsorbed onto the cMWCNT@paper for electrochemical detection. The linear detection range and sensitivity of the electrochemical biosensing assay were found to be 100 fM–100 nM and 5.09 μA (log[concentration])−1, respectively. The biosensing assay was further shown to detect the target genomic gonococcal DNA in a mixture consisting of different DNA and protein interferents indicating its clinical viability. The results of rheological studies reveal that this thixotropic cMWCNT ink can be utilized for screen printing. These studies demonstrate the utilization of a conductive ink formulation for the fabrication of paper-based electrochemical sensing electrodes having high potential for cost-effective batch production and application in point-of-care (PoC) clinical diagnostics. [ABSTRACT FROM AUTHOR]

Pesticide residues are a serious problem towards agriculture, environment and food safety, so it is highly desirable to develop a swift, efficient and portable pesticide detection method. A fluorescence visual sensing method for glyphosine based on a nitrogen-doped biomass carbon quantum dot (N-CQD) paper-based sensor was developed. The fluorescence signal was quenched by Fe3+ in a static quenching process, and then the fluorescence of N-CQDs was recovered after adding glyphosine. Under the optimal experimental conditions and when tested with a fluorescence spectrofluorometer, the detection of glyphosine showed a two-stage linear pattern in the range of 0.1–0.6 μM and 0.6–1.6 μM with a detection limit of 0.075 μM. Then, the RGB values of different concentrations of glyphosine on the filter paper chip were detected by the software of the smartphone-color identifier. The logarithm of the glyphosine concentration was linearly related to the G value of RGB in the range of 0.25–10.00 mM and with a detection limit of 0.15 mM. The method was applied to measuring glyphosine-spiked juice and flour samples, and the recovery rates were 87.60–112.69% and 93.27–105.83%, respectively. The proposed N-CQDs/Fe3+ system had wide applications, and it was expected to be fast and effective at detecting pesticide residues. [ABSTRACT FROM AUTHOR]

A new fluorescent probe (T2) containing pyrene-hydrazone furan moieties was developed and synthesized through a two-step process and then coated onto filter paper to form a paper-based sensor for TNT detection. The T2 sensor uses photoinduced electron transfer (PET) induced fluorescence quenching to detect TNT. The sensor properties were studied using fluorescence spectra, 1H-NMR titration and density functional theory (DFT) calculations. The reaction time of the T2 paper-based sensor for TNT detection was only five minutes. A smartphone was used as an alternative instrument to detect fluorescence signals and a typical image J-processing application was employed to evaluate the grayscale values of the smartphone-captured photographs. The sensor showed a linear concentration range for TNT detection of between 30–500 μM and a detection limit of 30 μM. The T2 paper-based sensor was found to have high selectivity and sensitivity, and it can successfully detect and image TNT in actual samples. This research demonstrates that a T2 paper-based sensor is a promising alternative for TNT detection owing to its short reaction time, high selectivity, sensitivity, and easy applicability. [ABSTRACT FROM AUTHOR]

Metabolic alkalosis, the most common acid–base disorder, is related to significantly increased mortality in hospitalized patients. Hunting for pH sensors lying in the neutral to alkaline pH range still remains challenging and in demand. Herein, we engineered a colorimetric/fluorescent method for monitoring alkalic pH based on a phenylboronic acid-containing probe (DDPB). In this approach, the dicyanoisophorone group of DDPB acted as an optical signal moiety, while the boronic acid acted as the latent pH response site. It was exactly deciphered that the reversible pH monitoring principle is based on the deprotonation/protonation mechanism and intramolecular charge transfer (ICT) strategy via1H NMR and DFT calculations. This approach presented a pH-sensitive response over pH values ranging from 7.00 to 10.23 (pKa = 9.33) with excellent reversibility. We further explored its application in sensing pH on a paper substrate for visual and rapid detection. In addition, it was successfully applied to measure pH variations in HK-2 cells when the cells underwent alkalosis. This work extends the application of optical probes based on boronic acid under alkaline pH conditions, and provides a new strategy for the design of alkaline pH probes. [ABSTRACT FROM AUTHOR]

As a part of our ongoing research, we have synthesized a new fluorescence probe, p-C4A, based on a calix[4]arene substituted with 4-aminoquinoline moieties with amide linkages. p-C4A can selectively recognize Li+ and PO43− ions and has been characterized via an emission study, an absorption study, ESI-MS spectroscopy, a 1H NMR study and cyclic voltammetry. The fluorescence sensor p-C4A can operate over a concentration range of 5–170 nM for Li+ sensing and 5–80 nM for PO43− sensing. The R2 values obtained for the sensing of Li+ and PO43− ions are 0.9962 and 0.9911, respectively. p-C4A demonstrates a minimum detection limit of 6.15 nM for Li+ and 9.0 nM for PO43−. The quantum yields of p-C4A as its Li+ and PO43− ion complexes were found to be 0.014 and 0.27, respectively. Herein, we report an easy-to-use, low-cost, disposable, paper-based, fluorescent, wax-printed device for the rapid chemical screening of Li+ and PO43−. This device can be used as a quick, portable, multiple-test panel that is simple, lightweight, and disposable. Moreover, in order to assess its analytical applicability, the prepared sensor was successfully used for the determination of Li+ and PO43− from wastewater samples, validating the proposed ion recovery method with 96–99% recovery rates. [ABSTRACT FROM AUTHOR]

A chromone-based symmetrical dipodal Schiff base probe L was designed and synthesized for multi-analyte detection in both aqueous and organic media. L displayed a prominent 'turn-on' fluorescence response with Al3+ (LOD = 6.9 μM) via the chelation-enhanced fluorescence (CHEF) process in a fully aqueous medium based on the inhibition of the photoinduced electron transfer (PET) process. Moreover, the in situ generated [L-Al3+] system was able to detect pyrophosphate (PPi) under identical experimental conditions. The proposed sensing pathway is believed to be the complexation with aluminium, followed by the subsequent decomplexation of the system by PPi. Furthermore, as the probe was decorated with –NH functionalities, it attained fluorescence indications upon binding with a basic anion. The detection ability of the probe for fluoride ions (LOD = 6.8 × 10−8 M) in the organic medium was studied using the 'turn-off' emission change based on the formation of a N–H⋯F hydrogen bond and subsequent deprotonation, as well as a visual change in color from yellow to reddish-yellow under UV light. The in situ prepared [L-F−] adducts could potentially sense Zn2+ ions with a 'turn-on' response via the metal-induced release of the free probe. All of the spectroscopic analyses were recorded to support the recognition mechanism of the aforementioned analytes by the reported probe molecule L. The probe also found applications in testing real water samples. [ABSTRACT FROM AUTHOR]

"Waste" is "wealth": the transformation of biomass waste into high value-added substances holds significant environmental and economic importance. In our work, orange peel was effectively transformed into valuable fluorescent carbon quantum dots (CQDs) by solvothermal treatment. The resultant CQDs displayed favorable dispersion and a mean particle size of 3.14 ± 0.71 nm. Moreover, these CQDs exhibited a characteristic excitation-dependent fluorescence behavior, which can produce the maximum emission wavelength at 506 nm with excitation at 400 nm. Upon the introduction of permanganate (MnO4−), the fluorescence intensity of CQDs diminished gradually caused by the inner filter effect (IFE) as well as the static quenching effect (SQE). The results revealed that the CQDs can serve as a fluorescent probe, which possessed high performance in terms of sensitivity for quantitative analysis of MnO4−, boasting a low detection limit of 3.31 μM. Subsequently, the application of this fluorescent probe in actual water samples was further explored, resulting in a recovery rate between 98.18% and 101.69%, with relative standard deviations (RSDs) ranging from 1.85% to 2.68%, which was highly satisfactory. The portable paper-based sensor, fabricated by depositing CQDs onto filter paper, is capable of quantitatively and visually detecting MnO4− in combination with a smartphone, thus providing a rapid on-site detection tool for MnO4−. As far as we know, this study provides the inaugural account of a smartphone-based portable sensor for visual determination of MnO4− by using biomass waste based CQDs, suggesting its immense potential for real-time monitoring applications. [ABSTRACT FROM AUTHOR]

The integration of smartphones with visual-based paper strips has gained great attention because of the rapid, low-cost, and relible analysis. Herein, we report on the synthesis of a red luminescent europiumbased metal organic framework (Eu-MOF) for the detection of folic acid in pharmaceutical formulations. The Eu-MOF showed strong and stable red emission fluorescence (excited at 270 nm), and the emission was significantly quenched upon exposure to folic acid due to the inner filter effect. A fluorometric assay in solution and visual detection based on fluorescence on a paper strip were used independently to quantify folic acid. The paper strips were prepared using chromatography paper and with the aid of a smartphone, folic acid was visually detected. In solution, the calculated LOD was 0.3 mM with a dynamic linearity range from 1.0 to 12.50 mM. Meanwhile, in the visual detection based on a smartphone integrated with a paper test strip, the linearity was from 1.0 to 9.0 mM with 0.12 mM as the LOD. Color analysis, from the photographs taken with a smartphone, was performed via analyzing the RGB coordinates using the Image-J program. The luminescent probe was applicable to detect folic acid in various drug tablets with recovery data ranging from 95 to 103%. The application of smartphones and fluorescent paper strips provides reliable detection of folic acid for on-site analysis, particularly in remote rural areas. [ABSTRACT FROM AUTHOR]

The sustainable goal of technological advancement is to go from lab to site through the development of a sensitive, specific and portable sensor for pollution monitoring. Herein, we report a completely portable colorimetric prototype device for the selective monitoring of lead (Pb) pollution, mainly in air, which relies on a new aspect of analysing the colorimetric assays on paper strips by the direct measurement of the retroreflective information, other than the available tedious image analysis methods. Our indigenously developed citrate-functionalized silver nanoparticles (AgNPs) embedded in cellulose paper strips showed significant localized surface plasmonic resonance (LSPR) peaks in the blue region and with the increase in the Pb concentration, the LSPR band in the blue region decreased and a new peak appeared in the green region of the electromagnetic spectrum due to the formation of larger aggregates. The prototype device monitored these spectral changes and accordingly gave the Pb content present in the sample. In this work, we made the sample under study by the acid digestion of one of the widely present air-suspended particulates, i.e., PbO2. The prototype device is a suitable fielddeployable technique for environmental Pb sensing and will open up new perspectives for future advancement in low-cost paper-based sensing. [ABSTRACT FROM AUTHOR]

It is significant to develop low-cost and highly efficient electrocatalysts for the hydrogen evolution reaction (HER) via electrochemical water splitting. Herein, we constructed P-doped NiCo2S4 nanowire arrays on carbon fiber paper (NiCo2S4−xPx/CFP) as a HER electrocatalyst in both acidic and alkaline media. Benefitting from P doping into NiCo2S4, the as-prepared NiCo2S4−xPx/CFP exhibits low HER overpotentials of 80 and 132 mV in acidic and alkaline media at a cathodic current density of 10 mA cm−2, respectively, which are far superior to counterparts of NiCo2S4 nanowire arrays on the carbon fiber paper (NiCo2S4/CFP). Meanwhile, the NiCo2S4−xPx/CFP presents excellent HER stability of 20 hours in acidic and alkaline media. From the results of density functional theory calculations, P doping can not only optimize the hydrogen adsorption energetics on each kind of atomic site of catalysts, but also strengthen the H2O molecule binding ability on the catalyst surface for the alkaline HER and favor kinetics of hydrogen adsorption and H2 formation on the catalyst surface for the acidic HER, eventually improving overall HER performances. The investigation of the HER mechanism modulated by P doping in our work offers novel inspiration to develop highly efficient ternary metal sulfides for the HER. [ABSTRACT FROM AUTHOR]

Recently, hydrogen peroxide (H2O2) has been used as a disinfectant in sanitizers for cleaning hands, and solid surfaces of hospitals, offices and homes to prevent the spread of the COVID-19 virus. The effluents from domestic, hospital and municipal waste should be monitored for their H2O2 content to avoid the entry of this toxic pollutant into the ecosystem. Therefore, we developed a low-cost graphene (Gr)-printed paper electrode for determination of H2O2 using cyclic voltammetry (CV). An office inkjet-printer and Gr nano-ink stabilized with ethyl cellulose (EC) were used for the fabrication of printed paper electrodes (PPEs) to determine H2O2 quantitatively. A stable Gr–EC nano-ink (2%) with viscosity and surface tension values of 12 mPa S−1 and 35 mN M−1, respectively, was formulated to obtain conductive electrodes. A wide linear range (2 μM–25 mM) with a better limit of detection (0.28 μM) for the determination of H2O2 was obtained when the Gr–EC/PPE was used as a working electrode. Further, the Gr–EC/PPE was successfully employed for analysis of H2O2 in wastewater. The electrochemical determination of H2O2 using the Gr–EC/PPE as an electrode in CV is rapid, economical, flexible and eco-friendly when compared with previously reported methods. [ABSTRACT FROM AUTHOR]

The integration of paper-based devices with fluorescent nanomaterials as recognition elements has offered novel opportunities for biosensing with enhanced sensitivity and selectivity, as well as stable signals. This work innovatively designed a fluorescent paper-based device for enantioselective sensing of D -alanine (D -Ala), where carbon dots (CDs) grafted cellulose paper (PCD) was used as the fluorophore and the in situ generated gold nanoparticles (AuNPs) were used as quenchers. D -α-Amino acid oxidase (DAAO) stereo-selectively catalyzed D -Ala to produce hydrogen peroxide (H2O2), which mediated the in situ formation of PCD/AuNPs composites and quenched the fluorescence of PCD based on fluorescence resonance energy transfer (FRET). Under optimal conditions, the designed PCD/AuNPs demonstrated a reliable quenching response to D -Ala in the range of 1–100 μM and the limit of detection was 0.55 μM. Moreover, the platform was applied to detect D -Ala in serum, simulated gastric fluid samples, and was further employed to determine D -Ala in BGC-823 gastric cancer cells with satisfactory results. Ultimately, the PCD/AuNPs platform provided a novel strategy for the development of reliable and sensitive assays based on paper-based devices. It has great potential to be utilized in enantioselective sensing and clinical early diagnosis. [ABSTRACT FROM AUTHOR]

The practicality of portable fluorescent detectors has attracted widespread attention. Herein, a series of luminogens was obtained via integrating pyrrole/fluorinated-pyrrole with triphenylamine in high yield. The emission performance was modified via varying the F and CN substituents on the pyrrole ring. The compounds TPACHO and TPAFCHO, with aldehyde-group-substituted pyrrole, exhibit significant mechanochromic luminescence (MCL) behavior and typical AIEE properties. The compounds TPA2CN and TPA2FCN can efficiently detect liquid and gaseous hydrazine hydrate, and they can achieve paper-based detection through visually clear emission color switching from yellow/orange to blue. The minimum detectable concentration of hydrazine was 10 mM. Moreover, TPA2CN exhibits good inhibitory activity toward human nasopharyngeal tumor cells (CNE1) and it has application prospects in tumor cell detection and biological cell monitoring. Thus, such functionalized paper can be applied as highly selective discriminating test strips for hydrazine hydrate. [ABSTRACT FROM AUTHOR]

This work presents the development of a green paper-based analytical device (Green-PAD) array for pH detection. The array was obtained with natural dyes extracted from red cabbage (Brassica oleracea) and butterfly pea flower (Clitoria ternatea); a filter paper was used as a substrate. The RGB indexes of the PADs' colors were extracted from the pictures taken using a smartphone or using a specifically developed RGB detector (Arduino-based) to obtain RGB indexes not affected by the light and the photocamera sensitivity. Multi-technique chemometric models were developed for calculating the pH value, starting from the RGB triplet of each sensing PAD. A preliminary and explorative chemometric analysis with PCA (partial component analysis) and TWPCA (3-way PCA) was carried out. Partial least square regression, PLS, was then applied to correlate the color of the PAD's picture with the solutions' pH. Different solutions at various pHs, ranging from 1 to 13, were obtained by titrating orthophosphoric acid with standardized NaOH, and they were used to create PLS models. Some real samples were examined as a test set, and the results were validated with pH-meter measurements. The ability of the PLS to model the experimental data was satisfactory since a good agreement between the experimental and fitted pH values was obtained. The proposed PADs were prepared with natural dyes and filter papers, so they are completely biodegradable and eco-friendly. Their fabrication does not require toxic or expensive reagents and sophisticated equipment. Also, the developed RGB detector, built-up with low-cost components and recycled batteries, adds value making the measurement cheap, easy and feasible also by non-expert people. [ABSTRACT FROM AUTHOR]

This document is a contents list for the New Journal of Chemistry, a publication by The Royal Society of Chemistry. It provides information about the journal's editorial, cover image, and articles featured in the current issue. The articles cover a wide range of topics in chemistry, including electrodeposition, supercapacitors, catalysis, and photocatalysis. Some specific papers discussed include the bactericidal effects of zeolitic imidazolate frameworks, the use of nanoparticle-decorated glyceryl monostearate as a targeted drug carrier, and the construction of S@C composites for Mg-S batteries. Other papers explore topics such as metal-organic framework-derived bimetallic oxides as anode materials for lithium-ion batteries, advancements in protection of steel surfaces using polystyrene supported nanoparticles, and the enhancement of vanadium dioxide for supercapacitor applications. The document also includes papers on coordination chemistry, synthetic approaches for coumestan derivatives, and the design of metal complexes for targeting breast cancer. [Extracted from the article]

This document is a contents list for the New Journal of Chemistry, a publication by The Royal Society of Chemistry and the Centre National de la Recherche Scientifique. It includes titles and authors of various articles covering topics such as hydrogenation products of fatty acids, macrocycles obtained from condensation reactions, and the characteristics of copper(II) Schiff base complexes as antimicrobial agents. Other papers mentioned in the document discuss catalytic hydrogenation, drug encapsulation, and the removal of pollutants from water. The document includes three papers and a correction, covering topics such as the synthesis of diaminoacetylene, the Z-scheme of 2D structured BCN and Ti MOF heterojunctions for photocatalytic hydrogen evolution, and the crafting of flexible film photocatalysts for formic acid production from CO2 and cyclization of thioamides. [Extracted from the article]

The document is a contents list for the New Journal of Chemistry, a journal focused on new directions in chemistry. It includes a list of communications and papers featured in the journal's latest issue, covering a range of topics such as the synthesis of specific compounds, analysis of porosity evolution, and the role of certain ions in chemical reactions. The journal is published by The Royal Society of Chemistry and the Centre National de la Recherche Scientifique. This document is a list of papers published in The Royal Society of Chemistry and the Centre National de la Recherche Scientifique journal, New J. Chem., in 2024. The papers cover a range of topics including crystal structures, semiconducting properties, and photocatalysis. The document provides a brief summary of each paper's topic and authors. [Extracted from the article]

The New Journal of Chemistry, published by The Royal Society of Chemistry, has released its latest issue containing a variety of articles on different topics in chemistry. The articles cover subjects such as photophysicochemical properties, synthesis of novel compounds, and catalytic reactions. Some specific topics explored in the papers include the synthesis of fluorescent compounds, structural dynamics of phosphorus-containing diesters, emission properties of glass ceramics, and the influence of different cations on spectral properties. Other papers discuss luminescence in lead-free perovskites, synthesis of materials for supercapacitors, photocatalytic activities of nanocomposites, and the adsorption and separation of composite pollutants. The journal aims to connect the world with the chemical sciences. [Extracted from the article]

The document is a contents list for the New Journal of Chemistry, a publication by The Royal Society of Chemistry. It provides a list of articles and papers that will be published in the journal, covering a wide range of topics such as asymmetric reactions, sodium-ion storage, and bone tissue engineering. The journal aims to connect the world with the chemical sciences. The document also includes two corrections for previously published papers. [Extracted from the article]

The New Journal of Chemistry, published by The Royal Society of Chemistry, has released its latest issue containing a variety of articles and papers on chemistry-related topics. The journal aims to connect the world with the chemical sciences and features papers on bioethanol fermentation, hydrogels in energy storage and biomedical technologies, environmentally responsible production, and other subjects. The document is a list of papers published in the journal, covering topics such as metal-organic frameworks, cycloaddition reactions, photochromic films, supercapacitors, computational predictions, catalysis, nanospheres, electrochemical sensors, and quantum dots. These papers offer valuable insights and advancements in the fields of chemistry and materials science. [Extracted from the article]

The document is a contents list for the New Journal of Chemistry, a publication that aims to connect the world with the chemical sciences. It provides information about the articles and papers included in the journal's latest issue. The articles cover a range of topics in chemistry, including the structural basis for Cu(II) metallocycle hexamer formation, photocatalyst-free hydrothiolation of gem-difluoroalkenes with thiols, and the construction of an alkynyl-containing porous polymer for enhanced photocatalytic H2O2 generation. The journal also invests its profits back into the chemistry community. Additionally, the document includes a correction to a previous paper on the effect of electrolyte optimization. [Extracted from the article]

The New Journal of Chemistry, published by The Royal Society of Chemistry and the Centre National de la Recherche Scientifique, contains a variety of research papers on topics such as graphite exfoliation, EPR characterization of N-oxyl radicals, anticancer efficacy, protoplast regeneration, semiconducting carbon nanotubes, and electrochemical sensing. The journal aims to provide new directions in chemistry and offers valuable insights and research findings for library patrons conducting research in these areas. The document is a list of papers published in the journal, covering a range of topics in chemistry and materials science, including pH-responsive nanotheranostics, synthesis of fused molecules, removal of tetracycline from water, and comparison of different species using UPLC-Q-TOF-MS. [Extracted from the article]

The document is a contents list for the New Journal of Chemistry, a publication by The Royal Society of Chemistry and the Centre National de la Recherche Scientifique. It features a variety of articles and papers covering topics such as anti-counterfeiting printing, monitoring platinum(IV) complexes, and the removal of uranium from the kidneys. The journal also provides information on training courses and resources for professional development in chemistry. The papers offer valuable insights and advancements in the field, making it a valuable resource for researchers and professionals in chemistry. [Extracted from the article]

The New Journal of Chemistry, published by The Royal Society of Chemistry and the Centre National de la Recherche Scientifique, has released a list of papers published in 2024. These papers cover a wide range of topics in the field of chemistry, including photothermal properties of MXenes, pseudomorphic transformation of silica, and adsorption behavior of chloramphenicol. Other papers explore drug abuse detection in hair samples, photocatalytic performance, small-molecule tracer imaging, catalytic studies, colorimetric sensing, and more. These papers offer valuable research and insights in various areas of chemistry. [Extracted from the article]

The aim of this paper is to evaluate the quality of 13 batches of rice and 17 batches of paddy. Differential scanning calorimetry curves, Fourier transform infrared spectroscopy, ultraviolet spectroscopy and electrochemical curves of 30 batches of rice and paddy were collected, and this paper utilized the quantitative fingerprints evaluated by using the systematic quantitative fingerprinting method, macro qualitative similarity (S m) and macro quantitative similarity (P m) to reflect the internal differences of the samples. A new quality assessment method was explored to quantify the obtained fingerprint profiles and to compare the correlation between the original fingerprints and the quantum fingerprints using a t-test. Using the parameters S m and P m as analysis criteria, hierarchical clustering analysis (HCA), orthogonal partial least squares discriminant analysis (OPLS-DA) and the equal-weight integrated evaluation method were used to evaluate the quality of the four analysis methods. [ABSTRACT FROM AUTHOR]

As one of the effective methods for hydrogen production, water electrolysis has been widely studied. However, the high overpotential challenge faced by the anode and the limitation of the electron transfer rate in this process significantly inhibit the efficiency of hydrogen production, which has become the main obstacle to overcome in the current research. The use of thermodynamically more favorable organic compounds to oxidize at the anode instead of traditional water oxidation (OER) is an effective strategy to optimize the process of electrolytic hydrogen production. In this paper, Ni3S2 catalysts co-doped with non-noble metals Li and Mn were prepared on nickel foam and used for the glycerol oxidation reaction (GOR) coupled with the hydrogen evolution reaction (HER). In alkaline solution, Li, Mn–Ni3S2@NF exhibits good GOR and HER performance. Specifically, overpotentials of 1.58 V vs. RHE and 0.54 V vs. RHE are required to reach a current density of 200 mA cm−2, respectively, and the catalytic performance of the material remains good after a long-term test. Li, Mn–Ni3S2@NF as a bifunctional catalytic material oxidizes glycerol to formate, and its faradaic efficiency (FE) is as high as 91%, and the volume of hydrogen production is close to the theoretical value. In addition, the replacement of the OER by the GOR can reduce the energy consumption by about 17.44%. [ABSTRACT FROM AUTHOR]

A novel 3D luminescent metal–organic framework (MOF) denoted as [Eu(BTA)0.5(H2BTA)0.5(H2O)]n (Cj-2) has been constructed from a π-conjugated ligand with a tetracarboxylate group, 1,2,4,5-benzenetetracarboxylic acid (BTA), via solvothermal synthesis. Structural analysis reveals that the Cj-2 framework is composed of tetranuclear secondary building units (SBUs) containing uncoordinated carbonyl groups which provide feasible recognition sites to interact with analytes. Cj-2 shows a trinodal (4,6,10)-connected 3D topological network consisting of tetranuclear SBUs. Cj-2 displays outstanding potential as a luminescent sensor for detecting o-NP and Cd2+ in DMF suspension, with remarkable sensitivity and selectivity through the luminescence quenching effect. Cj-2 displays excellent luminescence quenching behaviour in the presence of other competing interfering analytes and can be recycled at least four times for sensing o-NP and Cd2+. For Cd2+ ions, it is the host–guest interactions and for the nitroaromatic compounds, it is the competitive absorption of excitation energy and the electron transfer mechanism that are the probable mechanisms for such sensing processes. Moreover, visual fluorescent test papers based on Cj-2 were assembled and employed to selectively detect nitroaromatic compounds and metal ions. Based on the aforementioned results, Cj-2 can be considered as a potential luminescence sensor for detecting Cd2+ and o-NP. [ABSTRACT FROM AUTHOR]

Graphitic carbon nitride (gCN) has shown great potential in photocatalysis. Developing suitable cocatalysts is a critical way to enhance gCN's photocatalytic performance. In this paper cobalt–nickel bimetallic phosphide (CoNiP) was used as a cocatalyst to modify gCN. A gCN/CoNiP composite was successfully prepared by a simple hydrothermal method. XRD, XPS, SEM, UV-vis DRS, and PL characterization studies showed that a Schottky junction-like structure was constructed between gCN and CoNiP, which intensified the visible light response, enhanced the charge transfer rate and prohibited the recombination of photogenerated carriers, thus significantly improving gCN photocatalytic activity. Under simulated sunlight, the removal efficiency of methylene blue (10 mg L−1) was 97.8% by 120 min of irradiation, 44.6% higher than that of gCN. The quenching experiment showed that ˙O2−, ˙OH and h+ were the main active species. Based on the above points, the possible mechanism of photocatalysis was deduced. [ABSTRACT FROM AUTHOR]

Manganese dioxide is attractive for energy storage but still needs to be combined with highly conductive materials to improve its electrochemical properties. In this paper, δ-MnO2/GNS composites with three-dimensional structures were synthesized by anchoring hydrangea-like δ-MnO2 on graphene substrates. Physicochemical analysis shows that δ-MnO2 is uniformly anchored on the graphene surface, and adjacent hydrangea-like δ-MnO2 self-assembles to build a three-dimensional conductive network, and this special structure not only provides abundant surface active sites but also more fast channels for electron transport during electrochemical reactions. The optimized composite (δ-MnO2/GNS-1.8) exhibited excellent electrochemical performance with a high specific capacitance of 326.6 F g−1 at a current density of 0.2 A g−1 and a cycling performance of 97.1%. Asymmetric supercapacitors assembled with δ-MnO2/GNS and activated carbon (AC) exhibited energy densities up to 42.2 W h kg−1 at a power density of 196.8 W kg−1. Hydrangea-like δ-MnO2 anchored on GNS has great potential for application as a high-performance supercapacitor electrode material. [ABSTRACT FROM AUTHOR]

In this paper, the geometric configuration, electronic properties, and optical characteristics of an InS/GaTe heterojunction have been computed using the foundational principles of density functional theory. The analysis indicates that when the interlayer distance is 3.88 Å, the binding energy is the most negative, indicating that the structure is the most stable. The bandgap of the two monolayers is larger than that of the heterojunction, which makes the photogenerated electrons of the heterojunction more easily excited. The InS/GaTe heterojunction is a type-II heterojunction that enhances the efficient dissociation of electron–hole pairs. In addition, the InS/GaTe heterojunction demonstrates strong absorption of ultraviolet light, rendering it suitable for applications in ultraviolet detectors and related fields. Furthermore, the bandgap electron transfer direction of the InS/GaTe heterojunction can be controlled by applying electrical force and mechanical pressure. The optical absorption coefficient of the InS/GaTe heterojunction can be adjusted to modify its optical properties. Finally, the possible future applications of the InS/GaTe heterojunction are discussed. [ABSTRACT FROM AUTHOR]

The degree of ease of use and the readily observable signals associated with the detection process are critical factors in determining the success of a detection strategy. Considering this perspective, we report the detection of phosgene by modulating the photophysical characteristics of a molecular probe, Xanth-NH2. The probe is non-emissive in nature, but the presence of phosgene facilitates the probe's radiative decay, which enables phosgene detection via fluorescence turn-on change. The fluorescence changes vary linearly with phosgene concentration, contributing to a nanomolar level detection limit for phosgene. Additionally, under a controlled set of conditions, the half-time for the reaction of Xanth-NH2 with phosgene is 68 s. To demonstrate the potential application of Xanth-NH2, probe-loaded paper strips or silica gel were developed as an economic tool for the detection of phosgene in vapor or solution phase. Phosgene detection has been accomplished with a portable UV light source and a smartphone to track minute changes during the detection event. [ABSTRACT FROM AUTHOR]

O-Vanillin derived Schiff base 1-[(E)-(2-hydroxy-3-methoxybenzylidene) amino]-4-methylthiosemicarbazone (VCOH) has been synthesized for colorimetric and fluorescence chemosensors towards PO43− ions. A fluorescence 'turn-on' sensing mechanism of VCOH towards PO43− ions has been explained due to emission from the VCO− ion formed upon transfer of the phenolic proton of VCOH to a PO43− ion. The 1 : 1 stoichiometry between the VCOH probe and PO43− ion is confirmed by Job's plot based on UV-vis titration. The limit of detection (LOD) of VCOH towards PO43− ions is found to be 0.49 nM. The PO43− ion sensing property of probe VCOH has been applied to prepare portable paper strips and for the analysis of real water samples. Fluorescence 'turn-on' and 'turn-off' responses of VCOH towards PO43−and H+ respectively have been used to construct a molecular logic gate. Fluorescence based sensing studies in which the concentration of analytes is adjusted over a broad range can be both laborious and expensive. In order to address these challenges, we have utilized various soft computing methods, including artificial neural networks (ANN), fuzzy logic (FL), and adaptive neuro-fuzzy inference systems (ANFIS), to appropriately model the 'turn-on' and 'turn-off' behaviors of the VCOH probe upon addition of PO43− and H+ respectively as well as to predict the experimental sensing data. [ABSTRACT FROM AUTHOR]

The document is a contents list for the New Journal of Chemistry, a journal focused on new directions in chemistry. It includes various articles and papers on topics such as lithium-ion batteries, organic synthesis, photocatalysts, and nanocatalytic systems. The journal is published by The Royal Society of Chemistry and the Centre National de la Recherche Scientifique. [Extracted from the article]

The chemistry of silver nanoparticles incorporating a covalently bound complexing agent is dealt with in this paper. The particles have been obtained by the direct reaction of silver ions with the ranelate species obtained from an old antiosteoporotic drug. The ranelate ion exhibits a thiophene structure encompassing a cyanonitrile and two carboxylic groups, in addition to a chelating nitrilebis(diacetate) moiety. Through metal substitution and redox processes involving decarboxylation at the C5-thiophene position, chocolate-brown silver-ranelate nanoparticles (AgNP@Ran) have been generated. As corroborated by the XPS and Raman data, the nanoparticles are strongly stabilized by Ag–C bonds and are inert to substitution. This allows the exploration of their coordination chemistry in the presence of transition and rare earth metal ions, under the influence of plasmonics and the SERS effect. Due to the small nanoparticle size and the high energy spectral band (415 nm), although no significant SERS response has been detected in the excitation range of 488–785 nm, a gradual enhancement has been observed over time, at 488 nm. This observation was ascribed to the laser-induced aggregation of the silver nanoparticles, leading to the SERS effect. The silver ranelate nanoparticles exhibited dramatic changes in their optical and SERS spectra in the presence of transition metal ions such as Cu(II), forming stable complexes in aqueous solution. In the case of Tb3+ ions, instead of the SERS effect, an enhanced fluorescence emission was observed, involving energy transfer from the ranelate ligand to the terbium 4f levels. In this way, silver ranelate nanoparticles make interesting optical sensors for metal ions and can be useful as fluorescent/plasmonic markers for chemical and biological systems. [ABSTRACT FROM AUTHOR]

Cell phones, tablets, laptop computers, and many other consumer technology gadgets use lithium-ion batteries (LIBs). The characteristics of lithium batteries include a high specific energy, great efficiency, and a long life. Owing to their distinctive qualities, lithium batteries are now the preferred power source for the electronics industry, with annual production in billions of units. This paper discusses several safety hazards introduced by mechanical, thermal, and electrical abuse as well as cutting-edge fixes for these difficulties. This review sought to achieve a deeper understanding of the safety risks of lithium-ion batteries depending on materials chemistry together with a positive response to these problems. This review discusses different methods for enhancing cell safety, including cooling, balancing, and cell chemistry. It then examines current safety regulations and associated testing procedures. Finally, it concludes with observations on potential future advancements and the prospects for safer lithium-ion batteries (LIBs). [ABSTRACT FROM AUTHOR]

In this paper, nitrogen-doped carbon quantum dots (N-CQDs) were prepared by using citric acid as a carbon source and ethylenediamine as a nitrogen source. Then, N-CQDs were added into a deep eutectic solvent (DES) synthesized from acrylamide (AM), urea (U), and choline chloride (ChCl). The N-CQDs/P(AM-U-ChCl) composite hydrogels were prepared by light polymerization. The chemical composition and microstructure of N-CQDs/P(AM-U-ChCl) composite hydrogels were characterized in detail using scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and Fourier transform infrared spectroscopy (FTIR). This article further explored the influence of the content of N-CQDs on the mechanical properties, adsorption properties, and detection performance of the composite hydrogel. The results showed that the composite hydrogels exhibited the best mechanical properties when N-CQDs' content was 0.3 wt%. The adsorption performance of N-CQDs/P(AM-U-ChCl) composite hydrogels for Fe3+ was significantly enhanced due to the carboxyl groups contained in N-CQDs. In detecting tert-butylhydroquinone (TBHQ), the composite hydrogel showed a good linear correlation in the concentration range of 0–200 mg L−1, and the detection limit of TBHQ reached 0.849 mg L−1. This study provides a new idea for preparing composite hydrogel materials with excellent mechanical properties and functionality. Also, it demonstrates their potential application value in heavy metal ion adsorption and organic molecule detection. [ABSTRACT FROM AUTHOR]

In this paper, a NiAl-LDH with the characteristic structure of a hydrotalc-like compound was applied as a carrier in a two-step hydrothermal process, and a MnCdS/In2S3/NiAl-LDH composite material was successfully prepared by loading MnCdS and In2S3 on the flower spherical-like surface of NiAl-LDH. The combination of NiAl-LDH with In2S3 and MnCdS made the band gap smaller and the light absorption range larger, thus increasing the utilization rate of light. 50% MnCdS/In2S3/NiAl-LDH composites had the best photoinduced charge separation and highest surface enrichment of photogenerated electrons. In the degradation experiment of crystal violet (CV), 50% MnCdS/In2S3/NiAl-LDH composites showed superior photocatalytic degradation efficiency (>98.5%) under full spectrum light. Furthermore, the applicability and universality of photocatalysts were studied by observing the degradation of CV by MnCdS/In2S3/NiAl-LDH composites under different conditions. In addition, the composites showed excellent hydrogen production capacity in the photolysis of water, in which hydrogen production within 8 hours was about 7661.51 μmol g−1. By combining the results of active species capture experiments, density functional theory (DFT) calculations and photoelectrochemical experiments, the possible mechanism of double S-scheme heterojunction photocatalysis among NiAl-LDH, In2S3 and MnCdS was inferred, which is one of the main reasons for the enhancement of photocatalytic activity. [ABSTRACT FROM AUTHOR]