Search

Excessive copper (Cu2+) causes adverse effects on human health and the ecological environment. Traditional methods for detecting Cu2+ have drawbacks such as high detection costs, complex operating conditions, and being time consuming. Therefore, there is an urgent need to develop simple detection methods to better meet specific health and environment quality needs. In this work, a paper-based fluorescence sensor was prepared (herein referred to as the as-prepared method) by immersing filter paper in aqueous polyethyleneimine (PEI) solution, and its potential use in Cu2+ detection was investigated. The results showed that the as-prepared paper samples, with fluorescence properties obtained by aggregation-induced luminescence of PEI, have selective recognition of Cu2+ based on the internal filtration effect, and the lowest detection limit is 0.03 μM. In addition, the relative error of this method is in the range of 1.80~2.23%, which is relatively comparable to the national standard method (0.63~630 μM), demonstrating high accuracy. Therefore, paper-based sensors with a simple preparation method have potential applications in the detection of Cu2+ in water. [ABSTRACT FROM AUTHOR]

Flexible paper-based materials play a crucial role in the field of flexible electromagnetic shielding due to their thinness and controllable shape. In this study, we employed the wet paper forming technique to prepare carbon fiber paper with a thickness gradient. The electromagnetic shielding performance of the carbon fiber paper varies with the ladder-like thickness distribution. Specifically, an increase in thickness gradient leads to higher reflectance of the carbon fiber paper. Within the X-band frequency range (8.2–12.4 GHz), reflectivity decreases as electromagnetic wave frequency increases, indicating enhanced penetration of electromagnetic waves into the interior of the carbon fiber paper. This enhancement is attributed to an increased fiber content per unit area resulting from a greater thickness gradient, which further enhances reflection loss and promotes internal multiple reflections and scattering effects, leading to increased absorption loss. Notably, at a 5 mm thickness, our carbon fiber paper exhibits an impressive average overall shielding performance, reaching 63.46 dB. Moreover, it exhibits notable air permeability and mechanical properties, thereby assuming a pivotal role in the realm of flexible wearable devices in the foreseeable future. [ABSTRACT FROM AUTHOR]

As air pollution escalates, the need for air filters increases. It is better that the filters used be based on natural fibers, such as non-wood fibers, which cause low damage to the environment. However, the short fiber lengths, low apparent densities, and high volumes of non-wood materials can make it challenging to prepare filter paper with the required mechanical and physical properties. In that context, this study focused on utilizing bamboo fibers to fabricate filter paper by employing the anthraquinone soda pulping method. The pulp underwent bleaching and oxidation processes, with the incorporation of cationic starch (CS) and polyvinyl alcohol (PVA) to enhance resistance properties, resulting in the creation of handmade filter papers. The findings revealed that the tear, burst, and tensile strength of filter paper increased with the oxidation and addition of CS and PVA. Air permeability increased with addition of PVA and combination of CS and PVA. FTIR demonstrated the conversion of hydroxyl groups in cellulose chains to carboxyl groups due to oxidation. SEM images illustrated alterations in the fiber structure post-oxidation treatment, with CS reducing pores while PVA and the CS-PVA combination enlarged pore size and enhanced porosity. The BET surface area surface area expanded with oxidation and the addition of the CS-PVA blend, indicating heightened filter paper porosity. Notably, the combined inclusion of CS and PVA not only augmented mechanical strength but also increased porosity while maintaining pore size. [ABSTRACT FROM AUTHOR]

In this study, Al paper and cellulose acetate (CA) filters derived from heated tobacco waste were successfully converted into current collectors and active materials for a supercapacitor device. Typically, heated tobacco contains electrically discontinuous Al paper. First, Al was extracted from the tobacco waste using HCl to produce Lewis acid (AlCl3). This acid was then used in an Al electrodeposition process utilizing the chloroaluminate ionic liquid reaction between the acid and the base (RCl) at room temperature. To enhance the conductivity, a supplementary coating of Al metal was applied to the Al paper through electrodeposition, thus re-establishing the electrical continuity of the discontinuous parts and forming an Al-coated current collector. Moreover, the CA filters were carbonized under a nitrogen atmosphere, yielding carbon precursors (C-CA) for the supercapacitor electrodes. To further enhance the electrochemical performance, nickel oxide (NiO) was incorporated into C-CA, resulting in C-CA@NiO with pseudocapacitance. The specific surface area of CA increased with carbonization and the subsequent incorporation of NiO. The as-synthesized C-CA and C-CA@NiO materials were applied to an Al-coated current collector to obtain C-CA- and C-CA@NiO-based electrodes, exhibiting stable electrochemical behavior in the voltage range of −1.0 to 0 V and 0 to 1.0 V, respectively. An asymmetric supercapacitor (ASC) device was assembled with C-CA@NiO and C-CA as the positive and negative electrodes, respectively. This ASC device demonstrated a high specific capacitance of 40.8 F g−1, while widening the operating voltage window to 2.0 V. The high electrochemical performance of the device is attributed to the successful Al electrodeposition, which facilitates the electrical conductivity and increased porosity of the C-CA@NiO and C-CA materials. To the best of our knowledge, this is a pioneering study in regards to the conversion of biomass waste into current collectors and active materials to fabricate a practical ASC device. Our findings highlight the potential of reusing Al paper and CA filters from heated tobacco waste as essential components of energy storage devices. [ABSTRACT FROM AUTHOR]

A thermoelectric generator (TEG) is one of the important energy harvesting sources for wearable electronic devices, which converts waste heat into electrical energy without any external stimuli, such as light or mechanical motion. However, the poor flexibility of traditional TEGs (e.g., Si-based TE devices) causes the limitations in practical applications. Flexible paper substrates are becoming increasingly attractive in wearable electronic technology owing to their usability, environmental friendliness (disposable, biodegradable, and renewable materials), and foldability. The high water-absorbing quality of paper restricts its scope of application due to water failure. Therefore, we propose a high-performance flexible waterproof paper-based thermoelectric generator (WPTEG). A modification method that infiltrates TE materials into cellulose paper through vacuum filtration is used to prepare the TE modules. By connecting the TE-modified paper with Al tape, as well as a superhydrophobic layer encapsulation, the WPTEG is fabricated. The WPTEG with three P–N modules can generate an output voltage of up to 235 mV at a temperature difference of 50 K, which can provide power to portable electronic devices such as diodes, clocks, and calculators in hot water. With the waterproof property, the WPTEG paves the way for achieving multi-scenario applications in humid environments on human skin. [ABSTRACT FROM AUTHOR]

This paper discusses the results of the micro-Raman analysis performed on paper-like graphene oxide (GO) samples consisting of many functionalised graphene layers and annealed at moderate temperatures (≤500 °C) under vacuum conditions (p ≃ 10−4 mbar). The analysis of the standalone samples revealed that the obtained material is characterised by a noticeable disorder level but still stays below the commonly accepted threshold of high or total disorder. GO formed in a simple way showed two spectral bands above 1650 cm−1 recorded very rarely or not at all and their origin has been discussed in detail. The results also confirmed the metastable character of multilayer GO after the annealing process at moderate temperatures as the C/O ratio was kept between 2 and 3 and the spectral features were stable within the annealing temperature range. [ABSTRACT FROM AUTHOR]

The dynamic mechanical behavior and cushioning performance of honeycomb sandwich panels, which are extensively employed in product cushioning packaging due to their exceptional energy absorption capabilities, were examined using a combination of experimental and numerical methods. Several factors, such as maximum acceleration–static stress, cushioning coefficient–static stress, and other curves, were analyzed under various impact conditions. The simulated stress–strain, deformation modes, cushioning coefficients, and other parameters demonstrate consistency with the experimental results. The acceleration, maximum compression, and cushioning coefficient obtained from the experiment and simulation calculation were 30.68 g, 15.44 mm, and 2.65, and 31.96 g, 14.91 mm, and 2.79, respectively. The results indicate that all error values were less than 5%, confirming the precision and reliability of the model. Furthermore, the model was utilized to simulate and predict the cushioning performance of honeycomb sandwich panels with different cell structures and paper thicknesses. These results provide a solid basis for enhancing the design of subsequent honeycomb element structures. [ABSTRACT FROM AUTHOR]

Polyurethane foams are materials characterized by low density and thermal conductivity and can therefore be used as thermal insulation materials. They are synthesized from toxic and environmentally unfriendly petrochemicals called isocyanates and polyols, which react with each other to form a urethane group via the displacement of the movable hydrogen atom of the −OH group of the alcohol to the nitrogen atom of the isocyanate group. The following work describes the synthesis of polyurethane foams, focusing on using environmentally friendly materials, such as polyols derived from plant sources or modifiers, to strengthen the foam interface derived from plant precipitation containing cellulose derived from paper waste. The polyurethane foam industry is looking for new sources of materials to replace the currently used petrochemical products. The solutions described are proving to be an innovative and promising area capable of changing the face of current PU foam synthesis. [ABSTRACT FROM AUTHOR]

The formation of a cellular hierarchically organized NiO film on a carbon paper substrate under hydrothermal conditions using triethanolamine as a base has been studied. The thermal behavior of the carbon paper substrate with the applied semi-product shell was studied using synchronous thermal analysis (TGA/DSC) and it was demonstrated that such modification of the material surface leads to a noticeable increase in its thermal stability. Using scanning electron microscopy (SEM), it was shown that the NiO film grown on the carbon fiber surface is characterized by a complex cellular morphology, organized by partially layered individual nanosheets of about 4–5 nm thickness and lateral dimensions up to 1–2 μm, some edges and folds of which are located vertically relative to the carbon fiber surface. The surface of the obtained material was also examined using atomic force microscopy (AFM), and the electronic work function of the oxide shell surface was evaluated using the Kelvin probe force microscopy (KPFM) method. The electrochemical parameters of the obtained flexible NiO/CP electrode were analyzed: the dependence of the specific capacitance on the current density was determined and the stability of the material during cycling was studied, which showed that the proposed approach is promising for manufacturing hierarchically organized electrodes for flexible supercapacitors. [ABSTRACT FROM AUTHOR]

This work presents the results of paper laser processing. It begins with the selection and examination of the processing parameters, then an examination of the properties of the modified papers and examples of applications of the developed modification method. The properties of laser-modified paper were studied using reflectance spectrophotometry to examine the colour aspects of the modified papers, scanning electron microscopy (SEM) and confocal microscopy for a morphological analysis, and Raman spectroscopy to analyse the papers under the influence of laser light. The influence of laser processing on the wettability of paper and the evenness of unprinted and printed paper was also investigated. The knowledge gained on paper surface modification with laser light was used to propose several applications, such as methods of marking, tactile detection, the controlled removal of optical brightener, ink, and metallised coatings from paper packaging, highlighting the design and aesthetics of paper. The developed laser-assisted method shows a promising, ecological approach to the design of many value-added paper products. [ABSTRACT FROM AUTHOR]

This paper examines the impact of the CO2 laser parameters on the tensile strength, which is one of the most important properties of paper packaging in the process of cutting paper material. The study was performed on a paper material sample Fbb Board/Ningbo Spark C1S Ivory Board by examination of the influence of four independent variables: paper material grammage, cutting speed, laser power, and resolution on the tensile strength by using definitive screening design. Optimum process conditions of four variables that maximize the tensile strength were predicted and validated accordingly. Results confirm that laser power, paper material grammage, and cutting speed are the main process parameters that mostly affect the tensile strength. Besides individual parameters, two statistically significant interactions were obtained: laser power and cutting speed, and cutting speed and laser resolution. Maximum tensile strength values (20.37 N/mm) were achieved using the laser power of 60.6%, cutting speed of 3.24%, resolution of 2500 Hz, and a paper material grammage of 326.85 g/m2. With laser power at middle values and at a lower speed, a maximum tensile strength value can be obtained. Increasing the laser power and cutting speed will produce a slight lowering of tensile strength. [ABSTRACT FROM AUTHOR]

The main objective of the presented research was to find a model that describes the maximum compressive force of paper in its plane. The research began with crushing tests of a number of packaging paper samples of various lengths. It was shown that due to the specific structure of the paper and the high heterogeneity of its structure, packaging paper is material where it is difficult to determine the maximum compressive stress. Next, three analytical models describing the load capacity of a flat paper web were investigated and an alternative empirical model was proposed. The results of the performed tests are directly applicable in the calculation of the mechanical properties of corrugated cardboard and the determination of the load capacity of cardboard packaging. [ABSTRACT FROM AUTHOR]

The study aims to present the results of paper compression under an axial load. Different heights of samples subjected to compression were taken into account. The main goal of the analysis was to determine experimentally the maximum compression load. In addition, numerical models based on the finite element method (FEM) were validated to refer to empirical results. The performed numerical simulations were founded on Green–Lagrangian nonlinear equations for large displacements and strains. The progressive failure of the compressed orthotropic material after exceeding maximum stresses was based on Hill's anisotropy theory. Nonlinear calculations were conducted by using a typical Newton–Raphson algorithm for achieving a sequence convergence. The accuracy of the developed model was confirmed experimentally in compression tests. The technique of analysing the shape of the compressed paper sample on the basis of images recorded during the measurement was used. The obtained test results are directly applicable in practice, especially in the calculation of the mechanical properties of corrugated cardboard and in determining the load capacity of cardboard packaging. Knowing the maximum compressive stress that packaging paper can withstand allows packaging to be properly designed and its strength assessed in the context of the transport and storage of goods. [ABSTRACT FROM AUTHOR]

The applications of waste-derived fuel from paper mills in industrial boilers benefit the reduction of carbon emissions. However, the co-combustion of waste-derived fuel and coal causes significant changes in the characteristics of the ash and brings about the need to find possible means of the utilization of the ash produced. In this work fly, ash samples were collected from circulating fluidized bed (CFB) boilers co-combusting paper mill wastes with coal and analyzed in detail. The chemical, physical, and thermal characteristics of two different co-combustion fly ashes (CCFA) were investigated using X-ray fluorescence (XRF), X-ray diffraction (XRD), thermogravimetry (TG), and scanning electron microscope (SEM). The chemical composition of CCFA is largely affected by the fuel source type. Thermal analyses of CCFA show that the type of desulfurization system used by the boiler influences the form of sulfate present in the fly ash. The presence of calcium sulfite hemihydrate can cause a high loss in the ignition of CCFA. By comparing the physical requirements specified in the ASTM standard for coal fly ash to be used in concrete, the CCFA produced from paper mill wastes was found to show good potential as supplementary cementitious materials. [ABSTRACT FROM AUTHOR]

In protecting cultural heritage, deacidification is used to stabilize acidic papers, ensuring the neutralization of acids present in the paper. But in the process of aging, several mechanisms of degradation occur simultaneously. Therefore, substances used to stabilize the paper should contain an antioxidant component in addition to the deacidifying component. The effect of the antioxidant (hindered amine light stabilizers—HALS type) on the stabilization of lignin-containing acid papers during accelerated aging was studied in this work. The effective deacidification component was magnesium; the solvent was hexamethyldisiloxane (HMDSO). The 4-amino-2,2,6,6-tetramethylpiperidine series of hindered amine light stabilizers (HALS) was selected as appropriate for creating a modifying system based on HMDSO. The modification system was tested on samples of a model test acid lignin-containing paper (NOVO) and naturally aged acidic paper from the real book. The addition of substances to the proposed deacidification system has a favorable effect on stabilizing the pH during aging and provides the inhibition of the oxidative degradation products and stabilization of the cellulose degree of polymerization. It was confirmed that the application of the system containing deacidification and an antioxidant component may increase the effectiveness of the protection of acid groundwood paper heritage objects. Adding a tested antioxidant to the proposed deacidification system has a favorable effect on stabilizing the pH value for a long time in accelerated aging. [ABSTRACT FROM AUTHOR]

Sulfate attack is one of the drawbacks of cementitious materials for stabilized soils. In the current study, a durability comparison of stabilized soil with cement (Type IV) and waste paper fly ash (WPFA) was conducted. First, the treated soil's unconfined compressive strength (UCS) was tested. Next, the treated soil was subjected to various wetting/drying cycles with various sulfate concentrations and temperatures for a year. In the meantime, samples were taken for DRX, FTIR, and TGA microstructural analyses. Additionally, samples were manufactured to track swelling over an 800 day period. The outcomes show that WPFA's UCS remained constant. Furthermore, ettringite development can be seen in the microstructural studies, however testing on linear displacement over 800 days revealed no significant changes in swelling. Finally, SEM was used to verify the ettringite formation at 360 days in order to confirm the previous findings. All the results indicated that stabilizing soil with 5% of WPFA and 3% of cement IV is possible even in presence of high sulfate concentrations, while maintaining the durability of the structure. [ABSTRACT FROM AUTHOR]

The coefficient of friction for different contacting materials against skin is mainly influenced by the nature of the materials (synthetic and natural fabrics), mechanical contact parameters (interfacial pressure and sliding velocities), and physiological skin conditions (ambient humidity and skin moisture content). In the present research work, seven different types of papers used in everyday life were analyzed. The physical properties of these materials were determined through tensile tests and friction tests. By comparing mechanical properties with coefficient of friction, it was possible to conclude that the coefficient of friction is strongly correlated with the mechanical properties. [ABSTRACT FROM AUTHOR]

Flexible calcium carbonate (FCC) was developed as a functional papermaking filler for high loaded paper, which was a fiber-like shaped calcium carbonate produced from the in situ carbonation process on the cellulose micro-or nanofibril surface. Chitin is the second most abundant renewable material after cellulose. In this study, a chitin microfibril was utilized as the fibril core for making the FCC. Cellulose fibrils for the preparation of FCC were obtained by fibrillation of the TEMPO (2,2,6,6-tetramethylpiperidine-1-oxyl radical) treated wood fibers. The chitin fibril was obtained from the β-chitin from the born of squid fibrillated in water by grinding. Both fibrils were mixed with calcium oxide and underwent a carbonation process by the addition of carbon dioxide, thus the calcium carbonate attached on the fibrils to make FCC. When used in papermaking, both the FCC from chitin and cellulose gave a much higher bulk and tensile strength simultaneously than the conventional papermaking filler of ground calcium carbonate, while maintaining the other essential properties of paper. The FCC from chitin caused an even higher bulk and higher tensile strength than those of the FCC from cellulose in paper materials. Furthermore, the simple preparation method of the chitin FCC in comparison with the cellulose FCC may enable a reduction in the use of wood fibers, process energy, and the production cost of paper materials. [ABSTRACT FROM AUTHOR]

The present study reports on the development by thermoforming of highly sustainable trays based on a bilayer structure composed of paper substrate and a film made of a blend of partially bio-based poly(butylene succinate) (PBS) and poly(butylene succinate-co-adipate) (PBSA). The incorporation of the renewable succinic acid derived biopolyester blend film slightly improved the thermal resistance and tensile strength of paper, whereas its flexural ductility and puncture resistance were notably enhanced. Furthermore, in terms of barrier properties, the incorporation of this biopolymer blend film reduced the water and aroma vapor permeances of paper by two orders of magnitude, while it endowed the paper structure with intermediate oxygen barrier properties. The resultant thermoformed bilayer trays were, thereafter, originally applied to preserve non-thermally treated Italian artisanal fresh pasta, "fusilli calabresi" type, which was stored under refrigeration conditions for 3 weeks. Shelf-life evaluation showed that the application of the PBS–PBSA film on the paper substrate delayed color changes and mold growth for 1 week, as well as reduced drying of fresh pasta, resulting in acceptable physicochemical quality parameters within 9 days of storage. Lastly, overall migration studies performed with two food simulants demonstrated that the newly developed paper/PBS–PBSA trays are safe since these successfully comply with current legislation on plastic materials and articles intended to come into contact with food. [ABSTRACT FROM AUTHOR]

Thermochromic inks (TC) have received increasing attention in recent years, particularly in the design and packaging industries. Their stability and durability are crucial for their application. This study highlights the detrimental effects of UV radiation on the lightfastness and reversibility of thermochromic prints. Three commercially available TC inks with different activation temperatures and in different shades were printed on two different substrates, cellulose and polypropylene-based paper. Used inks were vegetable oil-based, mineral oil-based and UV-curable. The degradation of the TC prints was monitored using FTIR and fluorescence spectroscopy. Colorimetric properties were measured before and after exposure to UV radiation. The substrate with a phorus structure exhibited better colour stability, suggesting that the chemical composition and surface properties of the substrate play a crucial role in the overall stability of thermochromic prints. This can be explained by the ink penetration into the printing substrate. The penetration of the ink into the structure (cellulose fibres) protects the ink pigments from the negative effect of the UV radiation. Obtained results suggest that although the initial substrate may appear suitable for printing, its performance after ageing may not be optimal. In addition, the UV curable prints show better light stability than those made of mineral- and vegetable-based inks. In the field of printing technology, understanding the interplay between different printing substrates and inks is critical to achieve high-quality, long-lasting prints. [ABSTRACT FROM AUTHOR]

In this study, high-pressure laminates (HPL) impregnated with phenol-formaldehyde (PF) resins enriched with kraft lignin were developed. Pulverised kraft lignin was added to the commercial PF resin in the amounts of 1% and 5% (solid to solid). Laminates were manufactured using pressure impregnation of the resins into the papers and using hot pressing of HPL in a laboratory press. Laminates with a lignin content of 1% (L-LPF-1) showed the highest bending strength (72.42 MPa) and Brinell hardness (9.41); they also exhibited the best moisture uptake (9.61) and thickness swelling after immersion in water (3.32%). Except for impact bending, laminates with a lignin content of 5% (L-LPF-5) had worse properties. However, the differences between the variants are mostly not statistically significant and are comparable with the results of commercial PF resin. Scanning electron microscopy confirmed the homogenous structure of produced laminates and the occurrence of cohesive failures in ruptured L-LPF-1 laminates, whereas in ruptured L-LPF-5 laminates adhesive failures were also observed. Based on the conducted research it can be said that the utilisation of kraft lignin as an additive to PF resin (in the amount of 1%) has a positive effect on the produced HPL. [ABSTRACT FROM AUTHOR]

The surface-enhanced Raman scattering (SERS) properties of low-dimensional semiconducting MXene nanoflakes have been investigated over the last decade. Despite this fact, the relationship between the surface characteristics and SERSing performance of a MXene layer has yet to be comprehensively investigated and elucidated. This work shows the importance of surface morphology on the overall SERS effect by studying few-layer Ti3C2Tx MXene-based SERS substrates fabricated by vacuum-assisted filtration (VAF) and spray coating on filter paper. The VAF deposition results in a dense MXene layer suitable for SERS with high spot-to-spot and substrate-to-substrate reproducibility, with a significant limit of detection (LoD) of 20 nM for Rhodamine B analyte. The spray-coated MXenes film revealed lower uniformity, with a LoD of 50 nM for drop-casted analytes. Moreover, we concluded that the distribution of the analyte deposited onto the MXene layer is affected by the presence of MXene aggregates created during the deposition of the MXene layer. Accumulation of the analyte molecules in the vicinity of MXene aggregates was observed for drop-casted deposition of the analyte, which affects the resulting SERS enhancement. Ti3C2Tx MXene layers deposited on filter paper by VAF offer great potential as a cost-effective, easy-to-manufacture, yet robust, platform for sensing applications. [ABSTRACT FROM AUTHOR]

As one of the raw materials of basic magnesium sulfate cement (BMSC), the activity of light-burned magnesium oxide (MgO) has an important effect on the hydration rate, hydration products, and mechanical properties of BMSC. To reveal the influence of packaging method, storage environment, and storage time on the activity of MgO and the mechanical properties of BMSC, an experiment was conducted by using ordinary woven bags, peritoneal woven bags, and plastic and paper compound bags to store the finished BMSC and the raw materials (light-burned MgO, MgSO4·7H2O, fly ash, and a chemical additive) under the conditions of natural environment, sealed environment, and wet environment, respectively. Comparative analysis of the effects of packaging method, storage conditions, and storage time on the activity of MgO and the mechanical properties of BMSC was performed through the mechanical strength test of mortar specimens. The results showed that in a sealed environment, the loss of a-MgO content in light-burned MgO was minimized, which was more conducive to keeping the mechanical properties of BMSC stable. In the wet environment, the mechanical strength of BMSC was significantly reduced in the early stage (1 day) due to the significant reduction in the activity of MgO, and the mechanical strength of the finished BMSC and prepared BMSC after 120 days of storage was still lost, regardless of the packaging method. However, the storage environment and packaging method had relatively little effect on the late mechanical strength (28 days) of BMSC. It is advisable to use ordinary woven bags for packaging in natural and sealed environments as this is more economical for engineering applications. Plastic and paper compound bags are superior to ordinary woven bags and peritoneal woven bags in wet environments. [ABSTRACT FROM AUTHOR]

This study evaluates the potential use of discarded plasterboard paper as fibers from buildings to reinforce concrete. Various concentrations of wastepaper fibers (0.5%, 1%, 1.5%, 2%, and 2.5% by weight of the binder) were investigated in this research. To mitigate the water absorption effect of the paper fibers, metakaolin was employed as a partial cement replacement. The results demonstrate that the inclusion of the wastepaper fiber enhances the mechanical and durability performance of the concrete. The optimal fiber proportion was identified as 1%, leading to a 29% increase in the compressive strength, a 38% increase in the splitting tensile strength, a 12% decrease in the water absorption, and a 23% decrease in the drying shrinkage with respect to the concrete containing 20% metakaolin. However, exceeding this optimal fiber content results in decreased mechanical and durability properties due to the fiber agglomeration and non-uniform fiber distribution within the concrete matrix. Based on the microstructural analysis, the improved performance of the concrete is ascribed to decreased porosity, more refined pore structure, and reduced propagation of microcracks within the concrete matrix in the presence of wastepaper fiber. According to the results, concrete containing 20% metakaolin and 1% wastepaper fiber exhibits durability and mechanical properties comparable to those of the traditional concrete. This finding highlights the significant promise of reducing dependency on conventional cement and incorporating suitable recycled materials, such as discarded plasterboard, and secondary by-products like metakaolin. Such a strategy encourages the preservation of resources, reduction in carbon dioxide emissions, and a decrease in the ecological footprint resulting from concrete production. [ABSTRACT FROM AUTHOR]

The title of the current Special Issue, "Feature Papers in Materials Simulation and Design", has identified the aims of this collection since its opening: the gathering of research works and comprehensive review papers that advance the understanding and prediction of material behavior at different scales, from atomistic to macroscopic, through innovative modeling and simulation. The paper by Chen et al. [[4]] aimed at studying the thermal properties and thermoelectric performance of imidazole-graphyne (ID-GY) by combining first principle calculations with the Boltzmann transport theory. The last paper by Cheng and Vescovini [[16]] presented instead an accurate and efficient numerical method for the analysis and design of Variable Stiffness (VS) laminates. Civalek et al. [[11]] developed an efficient eigenvalue algorithm for the axial vibration analysis of embedded short-fiber-reinforced micro-/nano-composite rods subjected to arbitrary boundary conditions. [Extracted from the article]

All-lignin coating formulations were prepared while combining water-soluble cationic kraft lignin (quaternized LignoBoost®, CL) and anionic lignosulphonate (LS). The electrostatic attraction between positively charged CL and negatively charged LS led to the formation of insoluble self-organized macromolecule aggregates that align to films. The structures of the formed layers were evaluated by atomic force microscopy (AFM), firstly on glass lamina using dip-coating deposition and then on handsheets and industrial uncoated paper using roll-to-roll coating in a layer-by-layer mode. Coated samples were also characterized by optical microscopy, scanning electron microscopy (SEM) coupled with energy dispersive spectroscopy (SEM/EDS), and contact angle measurements. It was suggested that the structure of all-lignin aggregates is the result of the interaction of amphiphilic water-soluble lignin molecules leading to their specifically ordered mutual arrangement depending on the order and the mode of their application on the surface. The all-lignin coating of cellulosic fiber imparts lower air permeability and lower free surface energy to paper, mainly due to a decrease in surface polarity, thus promoting the paper's hydrophobic properties. Moderate loading of lignin coating formulations (5–6 g m−2) did not affect the mechanical strength of the paper. [ABSTRACT FROM AUTHOR]

Flexible respiratory monitoring devices have become available for outside-hospital application scenarios attributable to their improved system wearability. However, the complex fabrication process of such flexible devices results in high prices, limiting their applications in real-life scenarios. This study proposes a flexible, low-cost, and easy-processing paper-based humidity sensor for sleep respiratory monitoring. A paper humidity sensing model was established and sensors under different design parameters were processed and tested, achieving high sensitivity of 5.45 kΩ/%RH and good repeatability with a matching rate of over 85.7%. Furthermore, the sensor patch with a dual-channel 3D structure was designed to distinguish between oral and nasal breathing from origin signals proved in the simulated breathing signal monitoring test. The sensor patch was applied in the sleep respiratory monitoring of a healthy volunteer and an obstruct sleep apnea patient, demonstrating its ability to distinguish between different respiratory patterns as well as various breathing modes. [ABSTRACT FROM AUTHOR]

To study the friction and wear performance of carbon fiber reinforced friction materials under different working conditions, paper-based friction materials with different fibers were prepared. Experiments on the SAE#2 test bench were conducted to study the infectors including friction torques, surface temperature, coefficient of friction (COF), and surface morphologies. The results were analyzed, which indicated that the carbon fiber reinforced friction material could provide a higher friction torque and a lower temperature rising rate under the applied high pressure and high rotating speed conditions. As the pressure increased from 1 MPa to 2.5 MPa, the friction torque of plant fiber reinforced material increased by 150%, the friction torque of carbon fiber reinforced material increased by 400%, and the maximum temperature of plant fiber reinforced and carbon fiber reinforced material reached the highest value at 1.5 MPa. Thus, carbon fibers not only improved the COF and friction torque performance but also had advantages in avoiding thermal failure. Meanwhile, carbon fiber reinforced friction materials can provide a more stable COF as its variable coefficient (α) only rose from 38.18 to 264.62, from 1 MPa to 2.5 MPa, which was much lower than the natural fiber reinforced friction materials. Simultaneously, due to the good dispersion and excellent mechanical properties of PAN chopped carbon fibers, fewer pores formed on the initial surface, which improved the high wear resistance, especially in the intermedia disc. [ABSTRACT FROM AUTHOR]

In order to further improve the performance of impregnated paper decorated blockboard (ecological board), high-density fiberboard (HDF) was selected as the equilibrium layer to replace the commonly used poplar veneer. Results showed that the performance of HDF ecological board can be comparable to that of poplar veneer ecological board. It had good appearance quality, and its surface scratch resistance, surface wear resistance, water resistance and mechanical properties met the requirements of National Standard GB/T 34722-2017. The surface cracking resistance of the ecological board prepared with HDF as the equilibrium layer reached the highest level (grade 5), far better than that of the poplar veneer ecological board. This was because HDF was a relatively homogeneous material, and its dry shrinkage in both the transverse direction and along the grain direction was much lower than that of the poplar veneer. This characteristic of HDF made it possible to improve the dimensional stability and bending resistance of blockboard substrates under dry and hot conditions. The formaldehyde emission of the HDF ecological board was higher than that of the poplar veneer ecological board, but it met the formaldehyde emission requirements of indoor materials according to GB 18580-2001. [ABSTRACT FROM AUTHOR]

Embossing is a converting process in which the surface of a tissue paper sheet is changed under high pressure, allowing different functions. In this work, the authors intend to study how the embossing pressure affects the main properties of tissue paper, using a laboratory embossing system. An optimum pressure was achieved at 2.8 bar to this embossing laboratory set-up. The effect of pressure when densifying the paper sheet gives it a gain in mechanical strength but no differences in terms of liquid absorbency. The two embossing patterns present different behaviors but both evidence losses in mechanical and softness properties. On the other hand, the finite element method (FEM) does not show clear evidence of how the pressure affects the paper strength. For the deco die, it is possible to observe that the amount of yielding is slightly higher for lower pressure (2.4 bar), but this plasticity state parameter is very similar for 2.8 bar and 3.2 bar. For the micro die, FEM simulations of the manufacturing pressure do not show a considerable impact on the amount of plasticity state of the material; only for 3.2 bar, it shows a change in the pattern of the plasticity state of the paper during the embossing processes. In the end, to achieve a final product with excellent quality, it is important to make a compromise between the various properties. [ABSTRACT FROM AUTHOR]

Efficient and sustainable energy storage remains a critical challenge in the advancement of energy technologies. This study presents the fabrication and electrochemical evaluation of a self-supporting electrode material composed of MnO2 nanorods grown directly on a carbon paper and carbon nanotube (CNT) substrate using a hydrothermal method. The resulting CNT/MnO2 electrodes exhibit a unique structural architecture with a high surface area and a three-dimensional hierarchical arrangement, contributing to a substantial electrochemical surface area. Electrochemical testing reveals remarkable performance characteristics, including a specific capacitance of up to 316.5 F/g, which is 11 times greater than that of conventional CP/MnO2 electrodes. Moreover, the CNT/MnO2 electrodes demonstrate outstanding retention capacity, exhibiting a remarkable 165% increase over 10,000 cycles. Symmetric supercapacitor devices utilizing CNT/MnO2 electrodes maintain a large voltage window of 3 V and a specific capacitance as high as 200 F/g. These results underscore the potential of free-standing CNT/MnO2 electrodes to advance the development of high-performance supercapacitors, which can be crucial for efficient and sustainable energy storage solutions in various industrial and manufacturing applications. [ABSTRACT FROM AUTHOR]

The characterization and modeling of the out-of-plane behavior of fiber-based materials is essential for understanding their mechanical properties and improving their performance in various applications, especially in the forming process. Despite this, research on paper and paperboard has mainly focused on its in-plane behavior rather than its out-of-plane behavior. However, for accurate material characterization and modeling, it is critical to consider the out-of-plane behavior. In particular, delamination occurs during forming processes such as creasing, folding, and deep drawing. In this study, three material models for paperboard are presented: a single all-material continuum model and two composite models using different cohesion methods. The two composite models decouple in-plane and out-of-plane behavior and consist of continuum models describing the behavior of individual layers and cohesive interface models connecting the layers. Material characterization experiments are performed to derive the model parameters and verify the models. The models are validated using three-point bending and bulge tests and show good agreement. A case study is also conducted on the application of the three models in the simulation of a deep drawing process with respect to wrinkle formation. By comparing the simulation results of wrinkle formation in the deep drawing process, the composite models, especially the cohesive interface composite model, show greater accuracy in replicating the experimental results, indicating that a single continuum model can also be used to represent wrinkles. [ABSTRACT FROM AUTHOR]

The lightweight aggregates used by the civil engineering market are sintered at a high temperature, about 1200 °C. In times of high energy prices and regulation of carbon dioxide emissions, lightweight aggregate products of the high-temperature process in sales marketing are not readily accepted. This study developed a sintered-type paper sludge lightweight aggregate. In order to reduce energy consumption, substitution of some reservoir sediment clay in paper sludge substitutes is to be expected. The study used two types of paper sludge (green clay paper sludge and paper pulp sludge). The sintering temperature was reduced effectively as the green clay paper sludge was substituted for some of the reservoir sediment clay, and the optimum substitute ranges of green clay paper sludge were 10%-50%. The optimum substitute ranges of the paper pulp sludge were 10%-40%. Test results show that the properties of aggregates have a particle density of 0.66-1.69 g/cm3, a water absorption of 5%-30%, and a loss on ignition of 10%-43%. The loss on ignition of aggregate became greater with the increase in paper sludge content. This means that the calorific value provided by the paper sludge will increase as paper sludge content increases. Paper sludge can therefore be considered a good material to provide heat energy for sintering lightweight aggregate. [ABSTRACT FROM AUTHOR]

In recent years, several studies have reported the recycling of by-products generated by the paper industry and their application to the construction industry. A majority of the existing studies used waste paper sludge ash, and considerable energy is consumed in such incineration processes. This may further contribute to air pollution. In this study, we used waste newspaper (WNP), which underwent a simple crushing process without a separate high-temperature treatment process, and we integrated it in cement mortar. We prepared mortars containing 0%, 0.2%, 0.4%, 0.6%, 0.8%, and 1.0% ground WNP as a cement substitute. Subsequently, the fluidity, compressive strength, tensile strength, carbonation depth, drying shrinkage, and microstructure of the mortars were compared and analyzed. The 28-day compressive strength of the mortar samples with WNP was approximately 3.2–16.1% higher than that of the control sample. The 28-day accelerated carbonation depth of the samples with WNP was approximately 1.03–1.61 mm. Furthermore, their carbonation resistance was approximately 5.2–39.4% higher than that of the control sample. Compressive strength, tensile strength, and carbonation resistance were improved by appropriately using ground WNP as a cement substitute in cement mortar. In this study, the appropriate amount of WNP according to the mechanical properties of cement mortar was found to be 0.4–0.8%, and considering the durability characteristics, the value 0.6 was the most ideal. [ABSTRACT FROM AUTHOR]

In this work, we present a systematic study on solid Surface Enhanced Raman Scattering (SERS) substrates consisting of Au and Ag nanoparticles (NPs) loaded on filter paper with the dip-coating method. The aim of this work is to explore how a series of parameters (e.g., concentration of colloidal solution, different porosity of filter paper, and the presence of an aggregating agent) affects the analytical performance of paper-based SERS substrates. All the substrates developed in this study have been analyzed with two non-resonant probe molecules, 4-mercaptobenzoic acid (4-MBA) and adenine, in terms of (i) inter-sample repeatability, (ii) intra-sample repeatability, (iii) sensitivity, and (iv) overall SERS performance in terms of analyte quantification. Moreover, the issue of how to evaluate the repeatability for a solid SERS substrate is carefully discussed. [ABSTRACT FROM AUTHOR]

The goal of this paper is to fabricate innovative diaphragm headphones using graphene oxide paper (GOP) and GOP/epoxy nanocomposites (GOPC). Initially, graphene oxide suspension is fabricated, and the vacuum filtration method is adopted to make GOP. Then, vacuum bag molding is used to fabricate GOPC from GOP. Hot pressing and associated molds are adopted to fabricate line-indented (GOPC-L) or curve-indented patterns (GOPC-C) on the GOPC. The performances of one kind of GOP and three kinds of GOPC diaphragm headphones are analyzed based on their sound pressure level (SPL) curves achieved by the Soundcheck measurement system. There are four important processing parameters that will influence the performance of the diaphragm, including material type GOP versus GOPC, indented pattern type, sonication time on suspension, and graphene weight fraction in suspension. Compliances of various diaphragms are measured by the Klippel LPM laser measurement system. The results indicate that effects of sonication time and graphene weight fraction on SPL of GOP and GOPC headphones are in reverse, and this is associated with their difference on compliance (modulus), mass, damping ratio, and microstructure uniformity. Either GOPC-L or GOPC-C seems to improve the microstructure of the GOPC, and leads to better SPL performance. The correlation between the previous four factors and SPLs of four kinds of diaphragm headphones is proposed by using scanning electron microscope (SEM) to examine the microstructure of these diaphragms. [ABSTRACT FROM AUTHOR]

This study explores the pyrolysis process applied to various non-utilized waste materials, specifically focusing on separated plastics from municipal waste, wood waste (including pallets and window frames), paper rejects, and automotive carpets. Different combinations of these waste materials were subjected to pyrolysis, a process involving high-temperature treatment (600 °C) in a nitrogen atmosphere. The resulting products, including biochar, gas, and liquid fractions, as well as the residual waste materials, underwent comprehensive analysis. The evaluation of pyrolysis products emphasizes their quality, energy content, and potential applications. Notably, the pyrolysis gas derived from the combination of separated municipal plastics and waste wood exhibited the highest calorific value at 49.45 MJ/m3. Additionally, Mixture 2, consisting of plastic and wood waste, demonstrated the highest calorific value for the pyrolysis condensate, reaching 30.62 MJ/kg. Moreover, Mixture 3, benefiting from biochar utilization as a sorbent, displayed the highest iodine value at 90.01 mg/g. [ABSTRACT FROM AUTHOR]

The preparation of graphene materials from biomass resources is still a challenge, even more so if they are going to be employed as supports for electrocatalysts for water splitting. Herein, we describe the preparation and characterization of graphene oxides (GOs) from solid macroalgae waste obtained after processing an agar–agar residue. The structural and morphological characterization of the obtained GO confirm the presence of a lamellar material that is composed of few layers with an increased number of heteroatoms (including nitrogen) if compared with those observed in a GO obtained from graphite (reference). Three-dimensional electrodes were prepared from these GOs by depositing them onto a fibrous carbon paper, followed by electrodeposition of the catalyst, NiFe. The electrocatalytic performance of these hybrid systems for the oxygen evolution reaction (OER) showed a proactive effect of both graphene materials toward catalysis. Moreover, the electrode prepared from the algae-based graphene showed the highest electrocatalytic activity. This fact could be explained by the different structure of the algae-based graphene which, due to differences in the nucleation growth patterns and electroactive sites developed during the electrodeposition process, produced more reactive NiFe species (higher oxidation state). [ABSTRACT FROM AUTHOR]

In kraft paper mills, supersonic steam jets are used to remove deposits that build up on the heat exchanger tubes in the recovery boiler. In this study, the fracture toughness KC and work of fracture, WF, of simulated boiler deposits were measured at temperatures up to 500 °C to determine the optimal conditions for deposit removal. The model deposits experienced an important brittle to ductile transition at ~450 °C. Above this temperature, ductile deposits required lower peak force, but four times more energy to fracture when compared to those tested at lower temperatures. The transition was clear in scanning electron micrographs of the fracture surfaces. The findings have significant implications for mills wishing to optimize sootblower performance. [ABSTRACT FROM AUTHOR]

Hydrogen sulfide is present in active or extinct volcanic areas (mofettas). The habitable premises in these areas are affected by the presence of hydrogen sulfide, which, even in low concentrations, gives off a bad to unbearable smell. If the living spaces considered are closed enclosures, then a system can be designed to reduce the concentration of hydrogen sulfide. This paper presents a membrane-based way to reduce the hydrogen sulfide concentration to acceptable limits using a cellulosic derivative–propylene hollow fiber-based composite membrane module. The cellulosic derivatives considered were: carboxymethyl–cellulose (NaCMC), P1; cellulose acetate (CA), P2; methyl 2–hydroxyethyl–cellulose (MHEC), P3; and hydroxyethyl–cellulose (HEC), P4. In the permeation module, hydrogen sulfide is captured with a solution of cadmium that forms cadmium sulfide, usable as a luminescent substance. The composite membranes were characterized by SEM, EDAX, FTIR, FTIR 2D maps, thermal analysis (TG and DSC), and from the perspective of hydrogen sulfide air removal performance. To determine the process performances, the variables were as follows: the nature of the cellulosic derivative–polypropylene hollow fiber composite membrane, the concentration of hydrogen sulfide in the polluted air, the flow rate of polluted air, and the pH of the cadmium nitrate solution. The pertraction efficiency was highest for the sodium carboxymethyl–cellulose (NaCMC)–polypropylene hollow fiber membrane, with a hydrogen sulfide concentration in the polluted air of 20 ppm, a polluted air flow rate (QH2S) of 50 L/min, and a pH of 2 and 4. The hydrogen sulfide flux rates, for membrane P1, fall between 0.25 × 10−7 mol·m2·s−1 for the values of QH2S = 150 L/min, CH2S = 20 ppm, and pH = 2 and 0.67 × 10−7 mol·m−2·s−1 for the values of QH2S = 50 L/min, CH2S = 60 ppm, and pH = 2. The paper proposes a simple air purification system containing hydrogen sulfide, using a module with composite cellulosic derivative–polypropylene hollow fiber membranes. [ABSTRACT FROM AUTHOR]

The strain-hardening geopolymer composite (SHGC) is a new type of fiber concrete with excellent ductility and environmental friendliness. However, the high cost of fibers greatly limits its widespread application. This paper proposes the use of untreated low-cost polyvinyl alcohol (PVA) fibers and polyethylene (PE) fibers to develop a low-cost, high-performance SHGC. Axial compression and axial tension tests were conducted on the SHGC with different PE fiber volume fractions (1%, 1.5%, and 2%) and different PVA fiber replacement ratios (0%, 25%, 50%, 75%, and 100%) to investigate the hybrid effects of fibers with different surface properties and to reveal the mechanism of fiber hybridization on the mechanical behavior of SHGCs. The results show that increasing the PE fiber volume fraction improves the compressive and tensile ductility of the SHGC while increasing the PVA fiber replacement rate impacts the strength indicators positively due to the good interface effect formed between its hydrophilic surface and the matrix. When the PVA fiber replacement ratio is 100%, the compressive strength (93.4 MPa) of the SHGC is the highest, with a 21.1% increase compared to the control group. However, the tensile strength shows a trend of first increasing and then decreasing with the increase in the PVA fiber replacement ratio, reaching the highest at a 25% replacement ratio, with a 12.5% increase compared to the control group. Furthermore, a comprehensive analysis of the economic and environmental performance of the SHGC indicates that a 25% PVA fiber replacement ratio results in the best overall economic benefits and relatively low actual costs, although the effect of fiber hybridization on carbon emission indicators is not significant. This paper provides new ideas and a theoretical basis for designing low-cost SHGCs. [ABSTRACT FROM AUTHOR]

Constructing photonic crystals with core-shell structured nanoparticles is an important means for applications such as secure communication, anti-counterfeiting marking, and structural color camouflage. Nonetheless, the precise synthesis technology for core-shell structured nanoparticles at the hundred-nanometer scale faces significant challenges. This paper proposes a controlled synthesis method for core-shell structured nanoparticles using a template method. By using 100 nm diameter silica nanospheres as templates and coating them with a ferroferric oxide shell layer, SiO2@Fe3O4 core-shell structured nanoparticles with regular morphology and good uniformity can be obtained. The study experimentally investigated the effects of feed amount, modifiers, temperature, and feed order on the coating effect, systematically optimizing the preparation process. Centrifugal driving technology was used to achieve structural colors in the visible wavelength range. Additionally, the method successfully created well-defined and uniform core-shell structured nanoparticles using 200 nm diameter silica nanospheres as templates, demonstrating that this controllable synthesis method can effectively produce core-shell structured nanoparticles over a wide range of particle sizes. The template method proposed in this paper can significantly improve morphological regularity and size uniformity while effectively reducing the preparation cost of core-shell structured nanoparticles. [ABSTRACT FROM AUTHOR]

With the aim to systematically analyze the ambient relative humidity on the shrinkage strain of Engineered Geopolymer Composites (EGCs), this paper studied four variables (fly ash to ground granulated blast furnace slag mass ratio, alkali content, water–binder ratio, and fiber volume content) though orthogonal experimental design and three different relative humidity values (30%, 60%, and 100% RH). The results indicated that, for EGC specimens under 30% RH and 60% RH, the decrease in slag content and increase in alkali content both resulted in greater drying shrinkage. The addition of fibers effectively reduced the shrinkage strain, while a minor impact on shrinkage was presented by the W/B ratio. The first and second key factors affecting the drying shrinkage strain were the FA/GGBS ratio and the alkali content. The optimal ratio of FA/GGBS, alkali content, and fiber volume fraction were 0/100, 4%, and 1.5%, respectively. Dring shrinkage strain was decreased with the increase in ambient relative humidity. Compared with the shrinkage strain under 30% RH, the reduction in shrinkage strain under 60% RH and 100%RH was up to 46.1% and 107.5%, respectively. At last, a relationship between shrinkage strain and curing age under 30% and 60% RH was established with a fitting degree from 0.9492 to 0.9987, while no clear relationship was presented under 100% RH. The results in this paper provide a practical method for solving the shrinkage problem of EGCs. [ABSTRACT FROM AUTHOR]

This paper mainly explores the feasibility of using desert sand (DS) and recycled aggregate in cement-stabilized bases. Recycled coarse aggregate (RCA) and DS serve as the substitutes of natural coarse and fine aggregates, respectively, in cement-stabilized bases. A four-factor and four-level orthogonal test is designed to analyze the unconfined compressive strength, splitting tensile strength, and compressive resilient modulus. Furthermore, this paper investigates the effects of cement content, fly ash (FA) replacement rate, RCA replacement rate, and DS replacement rate on the road performance of cement-stabilized bases composed of RCA and DS. The test results reveal that the performance of cement-stabilized bases with partial RCA instead of natural coarse aggregate (NCA) and partial DS instead of natural fine aggregate satisfies the road use. The correlation and microscopic analyses of the test results imply the feasibility of applying DS and recycled aggregate to cement-stabilized bases. This paper calculates and evaluates the life cycle of carbon emissions of desert sand and recycled coarse aggregate cement-stabilized macadam (DRCSM) and finds that both DS and RCA can reduce the carbon emissions of CSM, which has a positive effect on improving the environment and solving the climate crisis. It is hoped that this paper can offer a solid theoretical foundation for promoting the application of DS and recycled aggregate in road engineering. [ABSTRACT FROM AUTHOR]

With the increasing drilling depth of mines, the cross-complexity of fissures in the rock body, and the frequent occurrence of sudden water surges, polymer slurry, with its advantages of good permeability and strong water plugging, is increasingly used in mine grouting projects. Additional research is needed in order to further improve the grouting performance of polymer slurry, ensure the safety of mining operations, and reduce the grouting cost. In this paper, a polymer composite grouting material was prepared with diphenyl methyl diisocyanate, polyether polyol, and fly ash, as the main raw materials, with coupling agent and catalyst as auxiliary reagents. The performance of the composite grouting material in terms of mechanical properties, thermal stability, hydrophobicity, and bonding was explored. This study's findings indicated that incorporating fly ash led to notable enhancements in the thermal stability and water resistance of the polymer slurry. Furthermore, the introduction of fly ash notably raised the starting degradation temperature of the polymer, boosted the water contact angle of the composite material, and reduced the density and reaction temperature of the composite material. In addition, the catalyst and coupling agent as auxiliary reagents affected the polymers in terms of mechanical properties; in this paper, dibutyltin dilaurate was used as the catalyst, and organosilanes were used as the coupling agent. The catalyst successfully sped up the polymer's gel time, however, an excessive quantity of catalyst compromised the polymer's mechanical characteristics. The addition of organosilanes has a positive effect on the dynamic mechanical properties of the composites, fracture toughness, compression, bending, and bond strength. The research can offer a theoretical direction for creating polymer mixtures in mine grouting projects. [ABSTRACT FROM AUTHOR]

The aim is to reduce the elastic deformation of the web and side walls of low-stiffness thin-walled beams when the floating fixture method is used. This paper takes the number and position of fixture points as the optimization variables, establishes a calculation model of elastic deformation, and constructs the objective function of maximum total elastic deformation. An optimized solution utilizing the augmented multiplier method is employed, which forms the basis for the fixture layout optimization method to reduce the elastic deformation of low-stiffness thin-walled beams. A theoretical calculation, simulation analysis, and the fixture layout optimization of total maximum elastic deformation were completed using an aluminum alloy low-stiffness thin-walled beam as an example. The results show that based on the optimized layout, the average relative error between the calculated value and the simulated value of total maximum elastic deformation is 17.43%, and the simulated value of maximum elastic deformation is reduced by 48.49% after optimizing the fixture layout. The measured value is reduced by 0.02 mm on average, and deformation is reduced by 74.07%, which verifies the effectiveness of the floating fixture layout optimization control of machining elastic deformation proposed in this paper. [ABSTRACT FROM AUTHOR]

The simulation of nano-scratching on metallic substrates using smooth particle hydrodynamics (SPH) has been attempted by researchers in recent years. From a review of the existing SPH simulations of nano-scratching processes, it was found that mainly two different material constitutive models (i.e., the Johnson–Cook model and the elasto-plastic model) were employed to describe the material flow. In the majority of these investigations, the Johnson–Cook model was employed to characterise the stress flow of the material subjected to scratching. A natural question remains as to which material constitutive model is preferable for the SPH modelling of nano-scratching when quantitatively predicting the process outcomes. In this paper, a quantitative comparison of material responses during the nano-scratching of copper is reported when the process is simulated using SPH with two different constitutive material models, namely the Johnson–Cook and the elasto-plastic models. In particular, the simulated cutting and normal forces as well as the machined topography using both approaches are compared with the experimental work reported in the literature. The SPH-based simulation results in this paper are investigated based on the following three aspects: (a) cutting and normal forces with different material models and depths of the cut, (b) the effect of the cutting speed on forces and its dependence on adopted material models, and (c) the effect of adopted material models on the surface topography of machined nano-grooves. The SPH simulation results showed that using the Johnson–Cook material model, cutting and normal forces were closer to the experimental data compared to the results obtained with the elasto-plastic model. The results also showed that the cross-sectional profile of simulated nano-grooves using the Johnson–Cook model was closer to the experimental results. Overall, this paper shows that the selection of the Johnson–Cook model is preferable for the SPH modelling of the nano-scratching process. [ABSTRACT FROM AUTHOR]

The increasing concern over environmental sustainability has prompted various industries to reassess their practices and explore greener alternatives. Dentistry, as a significant contributor to waste generation, is actively seeking methods to minimize its environmental footprint. This paper examines the environmental implications of clear aligner therapy (CAT) in orthodontics and explores strategies to prioritize sustainability in aligner manufacturing and usage. CAT has gained popularity as a viable alternative to traditional fixed appliances due to advancements in biomaterials and computer-aided design (CAD) and manufacturing (CAM) technologies. The global market for clear aligners is expanding rapidly, with significant growth projected in the coming years. To address these challenges, this paper proposes adopting the principles of reduce, reuse, recycle, and rethink (4Rs) in orthodontic practices. Strategies such as minimizing resource consumption, incorporating recycled materials, and promoting proper aligner disposal and recycling can significantly reduce environmental harm. This paper explores emerging technologies and materials to mitigate the environmental impacts of CAT. Additionally, initiatives promoting aligner recycling and repurposing offer promising avenues for reducing plastic waste and fostering a circular economy. In conclusion, while CAT offers numerous benefits in orthodontic treatment, its environmental impact cannot be overlooked. By implementing sustainable practices and embracing innovative solutions, the orthodontic community can contribute to a more environmentally conscious future while continuing to provide quality care to patients. [ABSTRACT FROM AUTHOR]

The green production of nanocomposites holds great potential for the development of new materials. Graphene is an important class of carbon-based materials. Despite its high carrier mobility, it has low light absorption and is a zero-bandgap material. In order to tune the bandgap and improve the light absorption, S, N co-doped low-dimensional C/C nanocomposites with polymer and graphene oxide nanoribbons (the graphene oxide nanoribbons were prepared by open zipping of carbon nanotubes in a previous study) were synthesized by one-pot carbonization through dimensional-interface and phase-interface tailoring of nanocomposites in this paper. The resulting C/C nanocomposites were coated on untreated A4 printing paper and the optoelectronic properties were investigated. The results showed that the S, N co-doped C/C nanoribbon/carbon dot hybrid exhibited enhanced photocurrent signals of the typical 650, 808, 980, and 1064 nm light sources and rapid interfacial charge transfer compared to the N-doped counterpart. These results can be attributed to the introduction of lone electron pairs of S, N elements, resulting in more transition energy and the defect passivation of carbon materials. In addition, the nanocomposite also exhibited some electrical switching response to the applied strain. The photophysical and doping mechanisms are discussed. This study provides a facile and green chemical approach to prepare hybrid materials with external stimuli response and multifunctionality. It provides some valuable information for the design of C/C functional nanocomposites through dimensional-interface and phase-interface tailoring and the interdisciplinary applications. [ABSTRACT FROM AUTHOR]

In this paper, the precipitation behavior and its effect on resistivity in a new type of nickel–iron-based alloy during short-term aging were investigated. During the aging process, the γ ′ phase increases in average size and decreases in number, with its area fraction fluctuating over time. This fluctuation is caused by the mismatch in the redissolution and growth rates of the γ ′ phase. As the area fraction of the γ ′ phase increases, the content of solute atoms in the matrix that scatter electrons decreases, lowering the resistivity of the alloy. Additionally, the continuous precipitation of M 23 C 6 at grain boundaries during aging causes the resistivity to gradually increase. This paper explains the fluctuation in the total amount of γ ′ phase during short-term aging and proposes a new method for characterizing the precipitation behavior of the γ ′ phase in the novel alloy using the relative trend of resistivity changes. [ABSTRACT FROM AUTHOR]