Search

The operation of solar photovoltaic installations for many years may lead to problems such as reduced energy efficiency and aging of components. Under this framework, replacing certain components in the facility to extend the service life of the power plant is viewed, in some cases, as a feasible strategy. However, despite its enormous strategic interest for the solar PV industry, we find that revamping PV installations has been the focus of very few scientific publications, and even less so when it comes to analyzing real facilities. Thus, this paper performs a techno-economic analysis of three revamping strategies at a real PV power plant located in the south-east of Spain. The strategies consist of substituting, in each case, the PV modules, the inverter, and both components. The simulated results show that the highest production value by installed power is obtained when both the modules and the inverter are replaced. In the same vein, the economic analysis reveals this scenario as the most favorable in terms of profitability. Based on the results obtained, an interesting future line of research would be focused on the extension of the analysis at country level to study the joint impact of numerous revamping actions. • Techno-economic analysis of revamping projects of a real solar PV power plant. • Replacing modules and inverter emerges as the most feasible strategy. • Study's applicability extends to other revamping initiatives and geographical regions. • Economic outcomes allow the most cost-effective alternatives to be determined. • This research can contribute to efficient and sustainable energy planning. [ABSTRACT FROM AUTHOR]

Energy performance certificate databases are a key tool for mapping national building stock and thus fostering greater overall energy efficiency. This paper presents an insight into the energy performance of residential and tertiary sector buildings in Spain, through an analysis of the first 129,635 energy performance certificates issued for existing buildings, collected by the Catalan Institute of Energy. Most of the residential buildings or building units that were studied were “E” class (53.6%). Single-family houses were found to use more energy on average (248.0 kWh p /m 2 ) than individual dwellings (183.2 kWh p /m 2 ). Tertiary sector buildings were found to have slightly better energy performance (26.4% of buildings were rated “D class”), with an average energy consumption of 317.8 kWh p /m 2 . Modern buildings consume less energy, as they must meet the higher energy performance requirements stated in thermal building regulations. Residential buildings or building units located in hotter climate zones consume slightly less energy than those located in colder zones, mainly because heating accounts for a high percentage of overall energy expenditure (70–75% in residential buildings). A significant proportion of the energy consumed in tertiary sector buildings is for lighting (37.2%). This research defines the current energy consumption baseline of existing buildings in Spain. The results can help to prioritize energy conservation efforts according to building type, construction period, climate zone and specific end-uses. They may also help public authorities to plan future energy policies, and construction practitioners to identify market segments and business strategies. [ABSTRACT FROM AUTHOR]

Hot-dip galvanisation (HDG) is the method most commonly used to protect steel surfaces from corrosion. However, HDG involves very intensive consumption of energy and resources. This paper aims to evaluate the environmental performance and hotspots in the Spanish HDG sector using cradle-to-gate life cycle assessment (LCA). Two Spanish HDG industrial plants, with different galvanisation capacities and manufacturing processes, were selected for the case study. The LCA revealed that the consumption of energy, fuels and nonrenewable resources were the most relevant environmental burdens at both plants. Steel was the main contributor, as it had the greatest influence on the plants' environmental profiles. The consumption of primary zinc and natural gas, used to dry and heat the molten zinc bath, also contributed to the impact of the HDG plants. This work proposes a normalisation to compare the Spanish sector against a European reference based on the average of 66 companies in 14 countries. The impacts of the Spanish HDG plants being studied were generally below the EGGA values, although the results are strongly influenced by the type of steel and the degree of material reuse implemented in the steel manufacturing process. The study lays the foundations for improvements in the resource efficiency and productivity of galvanisation plants. We propose alternatives such as the use of secondary zinc or modifications that will extend the lifespan of pickling baths, which would contribute to a more sustainable use of resources in the galvanising industry. Image 1 • The hot-dip galvanisation (HDG) sector in Spain was assessed via LCA. • Two HDG plants with different production properties provided detailed data inventories. • The highest impacts were found in the production of steel and primary zinc. • Using secondary zinc and extending pickling bath's lifespan would improve HDG. • The impacts of the Spanish HDG plants were generally below the European average. [ABSTRACT FROM AUTHOR]